Filters
total: 701
filtered: 642
Search results for: heavyweight concrete
-
Modeling of capillary fluid flow in concrete using a DEM-CFD approach
PublicationSformułowano połączone podejście do modelowania dwufazowego przepływu wody napędzanego hydraulicznie i kapilarnie w nienasyconym betonie. Proces przepływu analizowano numerycznie w mezoskali w warunkach dwuwymiarowych (2D), łącząc metodę elementów dyskretnych (DEM) z obliczeniową dynamiką płynów (CFD) w warunkach izotermicznych. Przeprowadzono w pełni sprzężone hydromechaniczne testy symulacyjne na małych próbkach betonu o uproszczonej...
-
Numerical analysis of behaviour of reinforced concrete elements under eccentric compression
PublicationPrzedstawiono wyniki modelowania nośności elementów żelbetowych stosując metodę elementów skończonych. Do opisu betonu zastosowano sprężysto-plastyczne prawo materiałowe wg Druckera-Pragera. Do modelowania stali zbrojeniowej zastosowano sprężysto-plastyczne prawo materiałowe według von Misesa. Obliczenia wykonano dla ścian żelbetowych.
-
A Non-local elasto-plastic model to describe localisations of deformation in concrete
PublicationPrzedstawiono wyniki numerycznej symulacji lokalizacji odkształceń stosując metodę elementów skończonych na bazie nielokalnego prawa sprężysto-plastycznego dla betonu. Prawo wykorzystuje długość charakterystyczną. Obliczenia dla ściskania jednoosiowego pokazały, że wyniki numeryczne nie zależą od siatki MES. Osiągnięto pełną regularyzację problemu brzegowego.
-
The method of analysis of damage reinforced concrete beams using terrestial laser scanning
PublicationThe authors present an analysis of the possibility to assess deformations and mechanisms of destructing bent reinforced concrete beams using the terrestrial laser scanning. As part of the experiments carried out at the Regional Laboratory of Construction of the Concrete Structures Division of the Civil and Environmental Engineering Faculty at Gdansk University of Technology, the reinforced concrete beams were subjected to destruction...
-
Electrochemical investigations of conductive coatings applied as anodes in cathodic protection of reinforced concrete
Publication -
THE METHOD OF ANALYSIS OF DAMAGE REINFORCED CONCRETE BEAMS USING TERRESTRIAL LASER SCANNING
PublicationThe authors present an analysis of the possibility to assess deformations and mode of failure of R-C beams using terrestrial laser scanning. As part of experiments carried out at the Regional Laboratory of Construction (at Gdansk University of Technology), reinforced concrete beams were subjected to destruction by bending and by shear. The process of press impact on the reinforced concrete beam was recorded using terrestrial laser...
-
Effect of admixtures on fresh grout and two-srtage (pre-placed aggregate) concrete
PublicationPrzedstawiono rezultaty badań doświadczalnych przeprowadzonych dla betonu uzyskanego metodą dwuetapową. Główną przeszkodą szerokiego zastosowania metody betonowania dwuetapowego Polcrete była niska wydajność urządzenia wytwarzającego mikrozaprawę - ultramiksera (UM). Celem przeprowadzonych badań laboratoryjnych było dobranie odpowiednich dodatków i domieszek, które umożliwią wytworzenie mikrozaprawy o takich samych parametrach...
-
The influence of texturing of the surface of concrete substrate on its adhesion to cement mortar overlay
Publication -
Experimental Study and Finite Element Modeling of Reinforced Concrete Column Having an Opening
Publication -
The quality management in precast concrete production and delivery processes supported by association analysis
Publication -
Investigation of Durability Properties for Lightweight Structural Concrete with Hemp Shives Instead of Aggregate
Publication -
Effect of a characteristic length on crack spacing in a reinforced concrete bar under tension
Publication -
DETECTION OF DEBONDING IN STEEL BARS EMBEDDED IN CONCRETE USING GUIDED WAVE PROPAGATION
PublicationThe paper presents a non-destructive diagnostic technique based on guided wave propagation phenomenon used to assess the adhesive bonding between a steel bar and a concrete cover. Double-layered cylindrical specimens with different levels of debonding and its location were investigated. The influence of bonding length on the excitation of multiple modes of longitudinal guided waves was analysed. Numerical simulations of guided...
-
The Impact of Homogeneity of High Modulus Asphalt Concrete Layer on Low-Temperature Cracking
PublicationDuring winter season of 2012 numerous transverse cracks developed in high-modulus asphalt concrete (HMAC) base of newly constructed motorway. Pavement cracked both in transverse joint locations and in the area between them. Research which was conducted during investigation of the causes and mechanisms of cracking consisted of: field examination, laboratory testing of specimens cored out of the existing pavement, computational analyses...
-
Effect of Particle Size of Fly Ash Microspheres (FAMs) on the Selected Properties of Concrete
PublicationThis paper presents the investigations of selected properties of concrete containing two fractions of fly ash microspheres (FAMs) with grain size up to 200 μm and up to 500 μm. Concrete mixtures with ordinary Portland cement and three substitution rates of cement by FAMs, 1.3%, 2.0%, and 2.6%, were investigated. For all concrete mixes, the constant water–binder ratio (w/b) equal to 0.50 was used. The research program included the...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublicationThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
Internal imaging of concrete fracture based on elastic waves and ultrasound computed tomography
PublicationThe condition assessment of concrete structures belongs to the greatest challenges of non-destructive testing. Monitoring the fracture process of concrete and detecting cracks at the earliest possible stage is a vital aspect to ensure the safety of civil engineering objects. The use of ultrasound tomography enables imaging the internal structure of a tested element. This study aims at the visualization of fracture damage in concrete...
-
Experiments and calibration of a bond-slip relation and efficiency factors for textile reinforcement in concrete
PublicationTextile reinforcement yarns consist of many filaments, which can slip relative each other. At modelling of the global structural behaviour, interfilament slip in the yarns, and slip between the yarns and the concrete can be considered by efficiency factors for the stiffness and strength of the yarns, and by applying a bond-slip relation between yarns and concrete. In this work, an effective and robust method for calibration of...
-
Fire-induced spalling of ultra-high performance concrete: A systematic critical review
PublicationUltra-high performance concrete (UHPC) is a novel concrete class characterized by a compressive strength of more than 150 MPa. One of the most significant drawbacks of employing UHPC is that is very low permeability owing to its great compactness of dense structure increases the risk of fire-induced spalling. It is challenging for fire safety and structural engineers to predict and analyze this issue due to the lack of widely accepted...
-
Non-uniqueness of fracture parameter choice in simulations of concrete cracking at mesoscale level
PublicationIn the paper a non-uniqueness of fracture parameter choice in simulations of cracking process in plain concrete specimens at mesoscale level under monotonic static loading is analysed. The Finite Element Method is used, where cracks are defined in a discrete way using interface cohesive elements with nonlinear material law including softening. The concrete mesostructure (such as: cement matrix, air voids, aggregates, and Interfacial...
-
Data-Driven Modeling of Mechanical Properties of Fiber-Reinforced Concrete: A Critical Review
PublicationFiber-reinforced concrete (FRC) is extensively used in diverse structural engineering applications, and its mechanical properties are crucial for designing and evaluating its performance. The compressive, flexural, splitting tensile, and shear strengths of FRCs are among the most important attributes, which have been discussed more extensively than other properties. The accurate prediction of these properties, which are required...
-
Characterization of corrosion in reinforced concrete beams using destructive and non-destructive tests
PublicationThe paper presents both non-destructive and destructive experimental tests on steel-reinforced concrete beams subjected to electrochemical corrosion. To examine the condition and behavior of the specimens, destructive tests were carried out, i.e., a three-point bending together with a modulated ultrasonic wave test. In addition, a series of non-destructive experiments were conducted, such as the potential measurement method, low-frequency...
-
Application of extended Finite Element Method to cracked concrete elements - numerical aspects
PublicationArtykuł omawia zastosowanie rozszerzonej metody elementów skończonych do zarysowanych elementów betonowych. Obliczenia wykonano dla elementów poddanych zginaniu i mieszanemu ściskaniu - rozciąganiu. Wyniki porównano z doświadczeniami.
-
Machine learning-based seismic response and performance assessment of reinforced concrete buildings
PublicationComplexity and unpredictability nature of earthquakes makes them unique external loads that there is no unique formula used for the prediction of seismic responses. Hence, this research aims to implement the most well-known Machine Learning (ML) methods in Python software to propose a prediction model for seismic response and performance assessment of Reinforced Concrete Moment-Resisting Frames (RC MRFs). To prepare 92,400 data...
-
Proceedings of the fib Symposium 2019: Concrete - Innovations in Materials, Design and Structures 2019
PublicationDesigning a concrete mix is a process of synthesizing many components, it is not a simple process and requires extensive technical knowledge. The design process itself focuses on obtaining the required strength of concrete. Very often designing a concrete mix takes into account the need to maintain the proper water-demand and frost-resistance features. The parameters that influence the concrete class most significantly are the...
-
Cost Analysis of Prefabricated Elements of the Ordinary and Lightweight Concrete Walls in Residential Construction
PublicationGlobal economic growth causes an increase in natural resources exploitation, particularly in construction branch. The growing use of electricity contributes to climate change. Therefore, it is necessary to search the solutions, which will allow for reducing natural resources exploitation. One of the many opportunities to do that is the application of the recycled materials. The authors of the given article have analyzed three variants...
-
Impact of reclaimed asphalt pavement (RAP) on low-temperature properties of asphalt concrete
PublicationHot mix recycling is a practice which enables reusing materials from old asphalt pavements. Current Polish regulations allow usage of RAP only for binder and base courses, and its amount is limited. Asphalt mixtures with RAP material have to fulfil requirements stated for typical asphalt mixtures. The research presents low-temperature properties of twelve different asphalt concretes with RAP material, determined using three-point...
-
Baseline-free debonding detection in reinforced concrete structures by elastic wave propagation
PublicationThe article presents the results of the numerical and experimental analysis concerning wave propagation in reinforced concrete (RC) beams with various extent of debonding between the steel rod and concrete cover. The main aim of the paper was to consider the unsolved research gaps, which considerably limit the application of wave-based methods in practice. The propagation of the flexural wave modes excited and registered on the...
-
Concrete Compressive Strength Under Changing Environmental Conditions During Placement Processes
PublicationThe technological process of concrete production consists of several parts, including concrete mix design, concrete mix production, transportation of fresh concrete mix to a construction site, placement in concrete framework, and curing. Proper execution of these steps provides good quality concrete. Some factors can disturb the technological process, mainly temperature and excessive precipitation. Changing daily temperature and...
-
Field Evaluation of High Modulus Asphalt Concrete Resistance to Low-Temperature Cracking
PublicationHigh-modulus asphalt concrete has numerous advantages in comparison to conventional asphalt concrete, including increased resistance to permanent deformations and increased pavement fatigue life. However, previous studies have shown that the construction of road pavements with High Modulus Asphalt Concrete (HMAC) may significantly increase the risk of low-temperature cracking. Those observations were the motivation for the research...
-
Experimental study of corrosion in reinforced concrete by acoustic emission and electrochemical noise techniques
PublicationTechnika emisji akustycznej jest znaną metodą badań korozji zbrojenia żelbetu. Źródłem aktywności akustycznej są zawsze zjawiska o naturze mechanicznej. Przedstawiono wynik badań akustycznych zbrojonego betonu w warunkach polaryzacji anodowej, przyspieszającej procesy korozyjne. Symultanicznie prowadzona była rejestracja szumu elektrochemicznego. Dla umożliwienia korelacji wyników, uzyskanych obiema technikami, wykonana została...
-
Electrochemical investigations of conductive coatings applied as anodes in cathodic protection of reinforced concrete.
PublicationW pracy przedstawiono rezultaty badań elektrochemicznych polimerów przewodzących z pigmentem grafitowym. Wyznaczono parametry elektrochemiczne badanych powłok w trakcie długotrwałej polaryzacji zbrojonego betonu. W oparciu o pomiary impedancyjne wyznaczono parametry elektrochemiczne powłok przewodzących. Wykazano, że badane powłoki mogą być stosowane w ochronie katodowej żelbetu. Badania wykazały, że optymalne stężenie grafitu...
-
Discrete modeling of micro-structure evolution during concrete fracture using DEM
PublicationW artykule pokazano wyniki dyskretne DEM dla betonu poddanego ściskaniu i rozciąganiu jednoosiowemu. Wyniki siła-przemieszczenie i zarysowania porównano z doświadczeniami. Szczególną uwagę zwrócono na zjawiska mikrostrukturalne podczas zarysowania na poziomie kruszywa.
-
Modelling of size effects in concrete using elasto-plascity with non-local softening
PublicationArtykuł przedstawia numeryczne symulacje MES efektów skali w materiałach kruchych takich jak beton , wykonane w warunkach płaskiego stanu odkształceń. Materiał był modelowany w ramach sprężysto-plastyczności z izotropowym wzmocnieniem i osłabieniem. W obszarze ściskania przyjęto liniowe kryterium Druckera-Pragera z niestowarzyszonym prawem płynięcia a w obszarze rozciągania liniowe kryterium Rankina ze stowarzyszonym prawem płynięcia....
-
FE-analysis of failure behaviour of reinforced concrete columns under eccentric compression
PublicationArtykuł omawia obliczanie słupów żelbetowych poddanych ściskaniu mimośrodowemu z uwzględnieniem lokalizacji odkształceń. Obliczenia wykonano przy zastosowaniu MES i sprężysto-plastycznego prawa konstytutywnego rozszerzonego o długość charakterystyczną mikrostruktury za pomocą teorii nielokalnej.
-
Effect of a characteristic length on crack spacing in a reinforced concrete bar under tension.
PublicationW artykule przedstawiono wyniki numerycznej obliczenia rozstawu rys w pręcie żelbetowym poddanemu rozciąganiu. Obliczenia wykonano przy zastosowaniu sprężysto-plastycznego modelu rozszerzonego o długość charakterystyczna mikrostruktury przy pomocy teorii nielokalnej.
-
Effect of aggregate structure on fracture process in concrete using 2D lattice model
PublicationArtykuł przedstawia symulacje rys w betonie przy zastosowaniu nowego modelu siatkowego. Zbadano wpływ rozkładu i wielkości kruszywa oraz wpływ strefy kontaktu na nośność i propagacje rys. Obliczenia były dwuwymiarowe.
-
Measurements and calculations of the width of the fracture process zones on the surface of notched concrete beams
PublicationArtykuł omawia wyniki pomiaru i analizy numerycznej szerokości strefy pękania w belkach betonowych z nacięciem. Do pomiarów zastosowano metodę DIC. Do symulacji zastosowano model sprężysto - plastyczny i model z degradacją sztywności. Oba modele zostały rozszerzone o nielokalne osłabienie. Wyniki symulacji porównano z doświadczeniami.
-
DEM modelling of concrete fracture based on its structure micro-CT images
PublicationW rozdziale książki zawarto numeryczne wyniki mezoskopowe dotyczące postępującego pękania betonu na poziomie kruszywa. Do badania procesu pękania belki betonowej z karbem w trzech (3D) i dwóch (2D) wymiarach zastosowano metodę elementów dyskretnych (DEM). Niejednorodność betonu uwzględniono stosując czterofazowy opis: kruszywo, zaprawa, makropustki i międzyfazowe strefy przejściowe. W obliczeniach DEM na podstawie zdjęć rentgenowskich...
-
SIMULATIONS OF FRACTURE IN CONCRETE BEAMS UNDER BENDING USING A CONTINUUM AND DISCRETE APPROACH
PublicationThe paper describes two-dimensional meso-scale results of fracture in notched concrete beams under bending. Concrete was modelled as a random heterogeneous 4-phase material composed of aggregate particles, cement matrix, interfacial transitional zones and air voids. Within continuum mechanics, the simulations were carried out with the finite element method based on a isotropic damage constitutive model enhanced by a characteristic...
-
A constitutive law for concrete with smooth transition from continuous into discontinuous cracks’ description
PublicationPaper presents a constitutive model for concrete that combines a continuous and discontinuous crack’s description to simulate the concrete under tensile dominated loads. In a continuum regime, two different constitutive laws were used. First, a plasticity model with the Rankine failure criterion and an associated flow rule was used. Second, a constitutive law based on isotropic damage mechanics was formulated. Both model alternatives...
-
Evaluation of suitability for 3D printing of high performance concretes
Publication -
The Effect of Aggregate Shape on the Properties of Concretes with Silica Fume
Publication -
Porosimetric, Thermal and Strength Tests of Aerated and Nonaerated Concretes
Publication -
Shear fracture of longitudinally reinforced concrete beams under bending using Digital Image Correlation and FE simulations with concrete micro-structure based on X-ray micro-computed tomography images
PublicationThe paper presents experimental and numerical investigations of the shear fracture in rectangular concrete beams longitudinally reinforced with steel or basalt bar under quasi-static three point bending. Shear fracture process zone formation and development on the surface of beams was investigated by Digital Image Correlation (DIC) whereas thorough analyses of 3D material micro-structure, air voids, width and curvature of shear...
-
Modes of Failure Analysis in Reinforced Concrete Beam Using Laser Scanning and Synchro-Photogrammetry
PublicationThe following paper reveal the limitations and possibilities of terrestrial laser scanning technology adaptation in diagnostics of reinforced concrete beams. In this paper, authors present potential spectrum of TLS use in modes of failure analysis of R-C beams and determines under which conditions the laser technologies might be applied. Research was carried out at the Regional Laboratory of Structural Engineering at Gdansk University...
-
Experimental investigation of Steel–Concrete–Polymer composite barrier for the ship internal tank construction
PublicationTransportation of dangerous cargo by ships demands ensuring an appropriate protection level in case of an accident. Two of the most dangerous accident types resulting in an oil spill are grounding and ship to ship collision. The article presents results of research on a new composite construction for a ship hull that increases structural safety during collision. The concept of semi-elastic Steel–Concrete–Polymer structure is presented....
-
The effect of aggregate characteristics on the fracture behaviour of fine-grained concrete under tensile loading
PublicationArtykuł przedstawia analizę wpływu kruszywa na zjawisko pękania drobnoziarnistego betonu podczas quasi-statycznego trzypunktowego zginania. Beton został opisany jako stochastyczny i niejednorodny materiał trzyfazowy. Dwuwymiarowe obliczenia numeryczne dla betonowych belek z nacięciem wykonano metodą elementów skończonych stosując izotropowy materiałowy model z degradacją sztywności rozszerzony o długość charakterystyczną mikrostruktury...
-
Numerical studies on size effects in concrete beams. Architecture Civil Engineering Environment ACEE
PublicationW artykule przedstawiony wyniki obliczeń efektów skali w belkach betonowych podczas zginania. Zastosowano model sprężysto-plastyczny z nielokalnym osłabieniem. Rozkład wytrzymałości na rozciąganie był stochastyczny - przestrzennie skorelowany. Belki były geometrycznie podobne. Wyniki porównano z modelem efektu skali Bazanta.
-
Restoration and preservation of the reinforced concrete poles of fence at the former Auschwitz concentration and extermination camp
PublicationThe objective of this study was to assess the present state of the reinforced concrete poles of fence at the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp. The poles were subjected to renovation about 10 years ago. After this time some deficiencies of applied renovation method were noticed. Cracks appeared between fresh and original part of concrete cover. Analysis of the reasons of these failures...