Filters
total: 677
filtered: 492
-
Catalog
Chosen catalog filters
Search results for: BPA
-
Pressure-induced phase transitions in LnTe (Ln=La, Gd, Ho, Yb) and AmTe
PublicationThe structural behaviour under compression of different lanthanide (La, Gd, Ho, Yb) and actinide (Am) monochalcogenides is studied by means of in situ high-pressure x-ray diffraction. All the investigated compounds crystallize at ambient conditions within a cubic (B1) NaCl-type structure but show different behaviours at high pressures. LaTe and AmTe undergo B1 to B2 (CsCl-type structure) phase transitions, starting at 9 GPa and...
-
Chemical composition, antioxidant and anticancer effects of the seeds and leaves and indigo (polygonum tinctorium Ait.) Plant
PublicationSeeds and leaves of indigo (Polygonum tinctorium Ait.) plant were investigated and compared with another medicinal plant named prolipid for their properties such as chemical composition, antioxidant, and anticancer effects by Fourier transform infrared, three-dimensional fluorescence spectroscopy, and electrospray ionization-MS in negative mode. It was found that polyphenols, flavonoids, and flavanols were significantly higher...
-
Mono- and polynuclear Co(II) silanethiolates with aliphatic diamines
PublicationFour Co(II) complexes, [Co{SSi(OtBu)3}2(dmpda)] 1, [Co{SSi(OtBu)3}2(bda)2]n2 [Co{SSi(OtBu)3}2(pda)2]n3 and [Co{SSi(OtBu)3}2(hda)2]n4 [dmpda = 3-(dimethylamino)-1-propylamine; bda = 1.4-butanediamine; pda = 1.5-pentanediamine; had = 1.6-hexanediamine] have been synthesized and characterized using X-ray diffraction. Complex 1 is mononuclear and contains Co(II) coordinated by dmpda molecule in chelating mode, whereas compounds 3 and...
-
The motion influence on respiration rate estimation from low-resolution thermal sequences during attention focusing tasks
PublicationGlobal aging has led to a growing expectancy for creating home-based platforms for indoor monitoring of elderly people. A motivation is to provide a non-intrusive technique, which does not require special activities of a patient but allows for remote monitoring of elderly people while assisting them with their daily activities. The goal of our study was to evaluate motion performed by a person focused on a specific task and check...
-
Optimization of biocorrosion resistance and mechanical properties of PM Ti–XAl–2Fe–3Cu alloys by response surface methodology
PublicationIn the current study, the biocorrosion resistance and mechanical properties of the Ti–XAl–2Fe–3Cu (wt%) (X = 6, 4, 2 wt%) alloy produced by powder compact extrusion of blended elemental powders were optimized by using the response surface methodology in order to gain the best combination of processing parameters. To run the optimization process, central composite design with three equal levels of oxygen, hydrogen and aluminum was...
-
Design and Implementation of a Dual-band Filtering Wil-kinson Power Divider Using Coupled T-shaped Dual-band Resonators
PublicationThe paper introduces a novel structure of a dual-band filtering Wilkinson power divider (WPD). Its essential component is a dual-band bandpass filter (BPF), implemented using coupling lines and two T-shaped resonators. The BPF is incorporated into the divider structure to suppress the unwanted harmonics within the circuit. The latter is achieved owing to a wide stopband of the filter. The deigned dual-band WPD can suppress third...
-
Quality Control of Bacterial Extracellular Vesicles with Total Protein Content Assay, Nanoparticles Tracking Analysis, and Capillary Electrophoresis
PublicationExtracellular vesicles (EVs) were isolated from Pectobacterium zantedeschiae culturing media using direct ultracentrifugation (UC), iodixanol cushion ultracentrifugation (ICUC), and iodixanol density gradient ultracentrifugation (IDGUC) techniques. The isolates were characterized with total protein content assay (bicinchoninic acid assay, BCA), nanoparticles tracking analysis (NTA), and capillary electrophoresis (CE). A satisfactory...
-
Fracture Surface Topography Parameters for S235JR Steel Adhesive Joints After Fatigue Shear Testing
PublicationThis paper presents the experimental results of a study investigating the effect of holes and notches made on the overlap ends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets bonded with Araldite 2024-2 epoxy adhesive were tested. For comparative reasons, static shear strength tests and high-cycle fatigue strength tests were performed. Adhesive-filled joints having three holes, each with a diameter...
-
Polyurethanes Crosslinked with Poly(vinyl alcohol) as a Slowly-Degradable and Hydrophilic Materials of Potential Use in Regenerative Medicine
PublicationNovel, slowly-degradable and hydrophilic materials with proper mechanical properties and surface characteristics are in great demand within the biomedical field. In this paper, the design, synthesis, and characterization of polyurethanes (PUR) crosslinked with poly(vinyl alcohol) (PVA) as a new proposition for regenerative medicine is described. PVA-crosslinked PURs were synthesized by a two-step polymerization performed in a solvent...
-
Modelowanie propagacji wiązek optycznych dla potrzeb konstrukcji systemów ramanowskich
PublicationW komunikacie zaproponowano wykorzystanie metody propagacji wiązki BPM do wspomagania procesu projektowania systemów ramanowskich przeznaczonych do badania struktur. Modelowania komputerowe zostało wykorzystane do optymalizacji wprowadzania wiązki laserowej do materiału, co zapewni zwiększenie efektywności wzbudzania sygnału rozpraszania ramanowskiego w wybranym miejscu w warstwie.
-
Biodegradability of simulant fluids and crude oil in aquatic environment
PublicationBiodegradowalność symulantów płynów była oceniana poprzez pomiar CO2 (EPA 560/6-82-003). Badaniu poddawane były emulsyjne i nieemulsyjne symulanty ropy oraz lekka ropa naftowa typu A z Północnej Ameryki. Uzyskane wyniki wskazują na łatwą biodegradowalność obu symulantów w porównaniu do badanej ropy naftowej.
-
Finding the Right Solvent: A Novel Screening Protocol for Identifying Environmentally Friendly and Cost-Effective Options for Benzenesulfonamide
PublicationThis study investigated the solubility of benzenesulfonamide (BSA) as a model compound using experimental and computational methods. New experimental solubility data were collected in the solvents DMSO, DMF, 4FM, and their binary mixtures with water. The predictive model was constructed based on the best-performing regression models trained on available experimental data, and their hyperparameters were optimized using a newly...
-
THE PROPERTIES OF NANOSILVER – DOPED NANOHYDROXYAPATITE COATING ON THE Ti13Zr13Nb ALLOY
PublicationThe aim of this research was to study the properties of nanohydroxyapatite (nanoHAp) and nanohydroxyapatite, doped with nanosilver (nanoHAp/nanoAg), coatings obtained by an electrophoretic deposition process. The suspensions was prepared by dispersing 0.1 g of HAp nanopowder for nanoHAp coatings and 0.1 g of nanoHAp and 0.025 g nanoAg for nanoHAp/nanoAg coatings. The deposition was carried out for 1 min at 50 V voltage followed...
-
Corrosion fatigue crack propagation rate characteristics for weldable ship and offshore steels with regard to the influence of loading frequency and seawater temperature
PublicationAfter Vosikovsky (1975), the corrosion fatigue crack growth rate (CFCGR) characteristics have been divided into three regions. The region-III rates are very close to mechanical fatigue crack growth rates. CFCGR formulae, including the long-crack length effect (in region I only), the loading frequency effect (in region II only), and the saltwater temperature effect, have been proposed. It has been assumed that CFCGR is proportional...
-
Effect of ionic liquids on surface and photocatalytic properties of selected semiconducttors
PublicationThe main aim of this doctoral dissertation was to explain the role of ionic liquids in shaping the morphology of selected semiconductors, thereby enhancing the photocatalytic activity. In order to achieve this goal, the following research steps were taken: (i) developing synthesis methods of selected semiconductors, with particular emphasis on the electrochemical oxidation method; (ii) understanding the influence of the selected...
-
Towards a Framework for Context Awareness Based on Textual Process Data
PublicationContext awareness is critical for the successful execution of processes. In the abundance of business process management (BPM) research, frameworks exclusively devoted to extracting context from textual process data are scarce. With the deluge of textual data and its increasing value for organizations, it be-comes essential to employ relevant text analytics techniques to increase the awareness of business process (BP) workers,...
-
The 41Σ+ electronic state of LiCs molecule
PublicationThe 41Σ+ state of LiCs molecule is observed experimentally for the first time. The inverted perturbation approach (IPA) method is used to derive the potential energy curve of the state from the measured spectra. The experiment is accompanied by theoretical calculations of adiabatic potentials for excited states in LiCs including 41Σ+, performed with the MOLPRO program package. The irregular shape of the 41Σ+ state potential predicted...
-
Synteza, właściwości i zastosowanie nowych (bio)degradowalnych poliestrouretanów.
PublicationArtykuł stanowi przegląd literaturowy dotyczący badań nad syntezą i wybranymi właściwościami dwóch grup nowych (bio)degradowalnych poliestrouretanów. W skłąd jednego z nich wchodzi polilaktyd (PLA) a drugiego alifatyczno-aromatyczny kopolimer poli[(tereftalanu-1,4-butylenu-co-(adypinianu 1,4-butylenu)] (BTA) i/lub ataktyczny poli(RS]-3-hydroksymaślan (a-PHB).
-
Activated Tungsten Inert Gas Weld Characteristics of P91 Joint for Advanced Ultra Supercritical Power Plant Applications
PublicationActivated Tungsten Inert Gas (A-TIG) welding, a variant of tungsten inert gas (TIG) welding, was used for welding P91. In Generation IV power plants, P91 welds are prone to premature failure due to the presence and formation of brittle phases and creep at high temperatures. When performing A-TIG welding, the flux composition plays a role in the reversal of the Marangoni flow in the weld pool, which ultimately determines the level...
-
Partial characterization of indigo (Polygonum tinctorium Ait.) plant seeds and leaves
PublicationThe aim of this study was to assess the contents of indigo's bioactive compounds, its antioxidant and anticancer activities in acetone, hexane and DMSO extracts and to compare the overall bioactivity with another more used medicinal plant named prolipid. It was found that the contents of the bioactive compounds in the studied extracts from different parts of indigo plant varied (P < 0.05): the significantly highest content of polyphenols...
-
Microcracking monitoring and damage detection of graphene nanoplatelets-cement composites based on acoustic emission technology
PublicationThis study aims to identify the micro-cracking pattern and structural applications of cement composites replaced with 0 wt%, 0.04 wt%, and 0.08 wt% contents of graphene nanoplatelets (GNPs) over cement weight through acoustic emission (AE) monitoring under mechanical degradation. The ultraviolet-visible spectroscopy (UV–vis) results showed that at 60 min sonication period, GNP-4 showed maximum absorbance rate of 16.15% compared...
-
Negocjacyjna metoda generowania protokołu uzgodnień na platformie EBXML
PublicationCelem standardu ebXML jest ustanowienie globalnej platformy dla biznesu elektronicznego, umożliwiającej dowolnym przedsiębiorstwom( bez względu na ich wielkość i lokalizację)poszukiwanie partnerów handlowych i realizowanie transakcji kupna-sprzedaży w oparciu o wymianę dokumentów elektronicznych o strukturze logicznej opisanej w XML.Podstawą do nawiązania kontaktu przez dowolny podmiot jest publikowany przez niego w specjalnym...
-
AutoCAD: Examination of Factors Influencing User Adoption
PublicationThe primary purpose of the research is to examine and validate determinants of user intention to use AutoCAD software, utilising the constructs from prior studies in a more integrated model. The paper proposes a revised Technology Acceptance Model (TAM) for measuring the adoption of AutoCAD. In the study, a latent construct PPA (perceived physical accessibility) was added to the proposed research model as a new determinant of AutoCAD...
-
Ocena jakości dostępnych na rynku suplementów diety zawierających kwasy tłuszczowe z rodziny n-3
PublicationCoraz większą uwagę zwraca się obecnie na uzupełnianie diety w NNKT, zwłaszcza kwasy EPA i DHA z rodziny n-3, w które bogaty jest olej rybi. Zbadano jakość dostępnych na krajowym rynku suplementów diety produkowanych z oleju rybiego w postaci kapsułek żelatynowych, ze szczególnym uwzględnieniem składu kwasów tłuszczowych i stabilności oksydatywnej.
-
Wpływ warunków ciśnieniowej filtracji na przebieg biologicznego usuwania azotu amonowego z wody w procesie nitryfikacji = Effect of pressure filtration conditions on nitrification process used for ammonia nitrogen removal from water
PublicationW pracy przedstawiono wyniki badań laboratoryjnych nad wpływem podwyższonego, zmiennego ciśnienia (do 0,8 MPa) na przebieg usuwania azotu amonowego z wody na nitryfikacyjnym złożu filtracyjnym. Wykazano, że ani podwyższone ciśnienie, ani jego zmiany nie wpływają hamująco na przebieg procesów nitryfikacji. Stwierdzono pozytywny wpływ płukania filtrów biologicznych na usuwanie azotu amonowego z wody.
-
Wyniki badań trwałościowych uszczelnień wału silnika hydraulicznego
PublicationW artykule przedstawiono wyniki badań różnych uszczelek wału ukierunkowane na wybór uszczelki o największej trwałości przy pracy pod ciśnieniem cieczy 2 MPa i z prędkością poślizgu min 2 m/s. Cieczą roboczą jest woda – ciecz o najgorszych właściwościach smarnych. W artykule opisano również oryginalny przyrząd, który pozwolił na pomiar wszystkich parametrów węzła uszczelniającego.
-
Ab initio chemical kinetics of Isopropyl acetate oxidation with OH radicals
PublicationGlobal reactivity descriptors of isopropyl acetate (IPA) and thermo-kinetic aspects of its oxidation via OH radicals have been studied. Transition state theory (TST) was utilized to estimate the bimolecular rate constants. Ten oxidation pathways have been investigated, and all of them are exothermic. The potential energy diagram has been sketched using different pre- and post-reactive complexes for all reaction pathways. Rate coefficient...
-
Photosensitive and pH-dependent activity of pyrazine-functionalized carbazole derivative as promising antifungal and imaging agent
PublicationCarbazole skeleton plays a significant role as a structural scaffold of many pharmacologically active compounds. Pyrazine-functionalized carbazole derivative was constructed by coupling 2-amino-5-bromo-3-methylaminepyrazine (ABMAP) into 3 and 6 positions of the carbazole ring. Multi-experimental methods were used, e.g., potentiometric, spectroscopic (ATR, UV, XRD powder,1H and13C NMR), electrochemical (cyclic voltammetry), and...
-
Chemical, Physical, and Mechanical Properties of 95-Year-Old Concrete Built-In Arch Bridge
PublicationThis research aimed to determine the durability and strength of an old concrete built-in arch bridge based on selected mechanical, physical, and chemical properties of the concrete. The bridge was erected in 1925 and is located in Jagodnik (northern Poland). Cylindrical specimens were taken from the side ribs connected to the top plate using a concrete core borehole diamond drill machine. The properties of the old concrete were...
-
Liquefaction of alder wood as the source of renewable and sustainable polyols for preparation of polyurethane resins
PublicationLiquefaction of wood-based biomass gives different polyol properties depending on the reagents used. In this article, alder wood sawdust was liquefied with glycerol and poly(ethylene glycol) solvents. Liquefaction reactions were carried out at temperatures of 120, 150 and 170 °C. The obtained bio-polyols were analyzed in order to establish the process efficiency, hydroxyl number, acid value, viscosity and structural characteristics...
-
Neural Graph Collaborative Filtering: Analysis of Possibilities on Diverse Datasets
PublicationThis paper continues the work by Wang et al. [17]. Its goal is to verify the robustness of the NGCF (Neural Graph Collaborative Filtering) technique by assessing its ability to generalize across different datasets. To achieve this, we first replicated the experiments conducted by Wang et al. [17] to ensure that their replication package is functional. We received sligthly better results for ndcg@20 and somewhat poorer results for...
-
Influence of stress on oxidation behaviour of carbon steel studded coil.
PublicationAnalizowano awarię wężownicy kołkowej ze stali węglowej pracującej przez 10 lat w środowisku przegrzanej pary w temperaturze 290ºC i ciśnieniu 0,67 MPa. Obserwacje mikroskopowe powierzchni i przekroju rury ukazały drobne pęknięcia w ściance wynikające z procesu selektywnego utleniania. Zastosowano metodę elementów skończonych w celu ustalenia zależności postępu korozji od ciśnienia i obciążenia cieplnego.
-
Ekspertyza naukowo-techniczna dotyczącą wybranych parametrów geowłóknin Elcen
PublicationPrzedmiotem ekspertyzy były badania parametrów fizycznych, wytrzymałościowych i hydraulicznych geowłóknin o symbolach: 150, 200, 300, 400, 500 i 600. W ramach prac badawczych określono następujące parametry techniczne: - masa powierzchniowa, - grubość pod obciążeniem: 2, 20 i 200 kPa, - wytrzymałość na rozciąganie i wydłużenie względne (metodą szerokich próbek), - siła przy przebiciu statycznym (metodą CBR), - charakterystyczna...
-
The combined effect of moderate pressure and chitosan on Escherichia coli and Staphylococcus aureus cells suspended in a buffer and on natural microflora of apple juice and minced pork
PublicationW pracy określono przeżywalność bakterii Escherichia coli i Staphylococcus aureus oraz naturalnej mikroflory soku jabłkowego i rozdrobnionego mięsa świńskiego po działaniu ciśnienia 193 MPa w temp. -20 C w obecności chitozanu. Stwierdzono, że traktowanie mikroorganizmów ciśnieniem w obecności chitozanu pozwala na przedłużenie trwałości badanych produktów przechowywanych w temperaturze chłodniczej o około 8-10 dni.
-
Improvement of microstructure and mechanical properties of high dense sic ceramics manufactured by high-speed hot pressing
PublicationNon-oxide ceramics possess high physical-mechanical properties, corrosion and radiation resistance, which can be used as a protective materials for radioactive wastes disposal. The aim of the present study was the manufacturing of high density SiC ceramics with advanced physical and mechanical parameters. The high performance on the properties of produced ceramics was determined by the dense and monolithic structure. The densified...
-
Poliuretanowo-stalowe konstrukcje sandwiczowe typu SIP
PublicationOpisano sposób otrzymywania elementów warstwowych stalowo-poliuretanowych typu SIP (Structural insulated panels). Rdzenie wykonano z mikroporowatych poliuretanów o różnej budowie chemicznej. Okładziny natomiast zastosowano ze stali weglowej. Dla wzmocnienia adhezji pomiędzy stalą a poliuretanem zastosowano klej. Na podstawie pomiarów mechanicznych stwierdzono, że moduł ścinania konstrukcji SIP i rdzenia z pianki PUR wynosił od...
-
Introduction = Wstęp
Publication''Przestrzeń publiczna - determinanta miasta europejskiego'' to tytuł sesji seminaryjnej, która odbyła sie w marcu 2005 roku jako spotkanie doktorantów zajmujących sie problemami współczesnego miasta europejskiego. Sesja była dopełnieniem warstztatów międzynarodowych zorganizowanych przez studenckie koło naukowe BUA Brygada Urbanistyczno-Architektoniczna pt:''Pawilon Europejski. E-pawilon?''. Temat jednoczącej się Europy znalazł...
-
Electric field effect on luminescence, and photoconduction in electron donor - electron acceptor organic solid films
PublicationZaobserwowano silne wygaszenie fotoluminescencji (80%) i duże fotoprądy (1mA/cm2) w układzie dendrymer aminowy m-MTDATA (donor elektronu) : pochodna fenantroliny BPT (akceptor elektronu) niedomieszkowanym oraz zawierającym domieszkę w postaci organicznego kompleksu platyny PtL2Cl. W interpretacji wyników uwzględniono elektrycznopolową dysocjację singletowych ekscypleksów m-MTDATA:BPT i trypletowych ekscypleksów m-MTDATA : PtL2Cl...
-
Hydrogen assisted cracking of high-strength weldable steel in sea-water.
PublicationOceniono niszczenie wodorowe stali o wysokiej wytrzymałości i jej złączy spawanych przy różnych rodzajach obciążenia w wodzie morskiej. Przeprowadzono próby rozciągania z małą prędkością odkształcenia i zmęczenia niskocyklowego w wodzie morskiej przy polaryzacji katodowej. Badano stal gatunku 17HMBVA o minimalnej granicy plasyczności 690 MPa oraz jej złącza spawane automatycznie łukiem krytym i ręcznie łukowo elektrodą otuloną.
-
Problemy bezpieczeństwa informacji w środowisku przetwarzania wszechobecnego
PublicationPrzetwarzanie wszechobecne jest dziedziną informatyki, któracoraz szerzej zaczyna pojawiać się w życiu przeciętnego człowieka, ułatwiając mu wykonywanie codziennych czynności. Przedstawiono pryncypia mechanizmów bezpieczeństwa, które należy bra pod uwagę przy implementacji tego typu systemu. Pokrótce opisano ideę przetwarzania wszechobecnego oraz aplikacji agentowych. Omówiono najważniejsze mechanizmy zabezpieczeń komunikacji...
-
Millimeter Wave Negative Refractive Index Metamaterial Antenna Array
PublicationIn this paper, a novel negative refractive index metamaterial (NIM) is developed and characterized. The proposed metamaterial exhibits negative effective permittivity (εeffe) and negative effective permeability (µeffe) at millimeter wave frequency of 28GHz. This attractive feature is utilized to enhance the gain of a microstrip patch antenna (MPA). Two thin layers of 5 5 subwavelength unit cell array of NIM are placed above a...
-
Cross-Linking, Morphology, and Physico-Mechanical Properties of GTR/SBS Blends: Dicumyl Peroxide vs. Sulfur System
PublicationIn this work, ground tire rubber and styrene–butadiene block copolymer (GTR/SBS) blends at the ratio of 50/50 wt%, with the application of four different SBS copolymer grades (linear and radial) and two types of cross-linking agent (a sulfur-based system and dicumyl peroxide), were prepared by melt compounding. The rheological and cross-linking behavior, physico-mechanical parameters (i.e., tensile properties, abrasion resistance,...
-
Wpływ nagniatania umacniającego na wytrzymałość zmęczeniową wałów okrętowych
PublicationW artykule przedstawiono przyczyny pękania śrubowych wałów okrętowych oraz możliwości zwiększenia ich trwałości, wskutek podwyższenia wytrzymałości zmęczeniowej połączenia wtłaczanego śruba - wał śrubowy przez nagniatanie umacniające. Badania wykonano na próbkach o średnicy 25 mm na specjalnie w tym celu zbudowanej w Politechnice Gdańskiej maszynie zmęczeniowej MZ 30 z wodnym systemem chłodzenia próbki przy użyciu cieczy. Próbki...
-
The effects of bifunctional linker and reflux time on the surface properties and photocatalytic activity of CdTe quantum dots decorated KTaO3 composite photocatalysts
PublicationNovel CdTe-KTaO3composite photocatalysts were successfully synthesized by using thioglycolic acid(TGA) or 3-mercaptopropionic acid (MPA) as linker molecules which facilitated attachment of CdTequantum dots to the surface of KTaO3nanocubes. The as-prepared photocatalysts were characterizedby UV–vis diffuse reflectance spectroscopy (DRS), X-ray diffraction (XRD), scanning electron microscopy(SEM), transmission electron microscopy...
-
Electronic States of Tris(bipyridine) Ruthenium(II) Complexes in Neat Solid Films Investigated by Electroabsorption Spectroscopy
PublicationWe present the electric field-induced absorption (electroabsorption, EA) spectra of the solid neat films of tris(bipyridine) Ru(II) complexes, which were recently functionalized in our group as photosensitizers in dye-sensitized solar cells, and we compare them with the results obtained for an archetypal [Ru(bpy)3]2+ ion (RBY). We argue that it is difficult to establish a unique set of molecular parameter values by discrete parametrization...
-
Bio-Based Polyurethane Networks Derived from Liquefied Sawdust
PublicationThe utilization of forestry waste resources in the production of polyurethane resins is a promising green alternative to the use of unsustainable resources. Liquefaction of wood-based biomass gives polyols with properties depending on the reagents used. In this article, the liquefaction of forestry wastes, including sawdust, in solvents such as glycerol and polyethylene glycol was investigated. The liquefaction process was carried...
-
Linear and Nonlinear Optical Properties of Azobenzene Derivatives Modified with an (Amino)naphthalene Moiety
PublicationThe design of two-photon absorbing azobenzene (AB) derivatives has received much attention; however, the two-photon absorption (2PA) properties of bis-conjugated azobenzene systems are relatively less explored. Here, we present the synthesis of six azobenzene derivatives and three bisazobenzenes substituted (or not) at para position(s) with one or two amino group(s). Their linear and nonlinear absorption properties are studied...
-
Influence of boundary conditions in calibration chamber
PublicationPrzedstawiono wyniki badań modelowych penetracji w komorze kalibracyjnej z zastosowaniem modeli o różnej średnicy. Badania przeprowadzono w piasku średnio zagęszczonym i zagęszczonym przy stałej składowej poziomej naprężenia i przy składowej pionowej naprężenia w gruncie do 400 kPa. Określono wpływ warunków brzegowych na uzyskane wyniki oporu podstawy/oporu stożka lub ostrza dylatometru. Wyznaczono współczynniki korekcyjne oraz...
-
Poliuretanowo-stalowe konstrukcje sandwiczowe typu SPS
PublicationPrzedstawiono sposób otrzymywania elementów warstwowych stalowo-poliuretanowych oraz wyniki ich badań wytrzymałościowych w próbach jednoosiowego zginania. Otrzymane elementy charakteryzowały się różnym stopniem rozwinięcia i przygotowania powierzchni oraz środkiem adhezyjnym. Na podstawie pomiarów stwierdzono, że moduł ścinania (G) dla układów warstwowych wynosił od 94 do 97 MPa, co świadczy o tym, że zastosowane środki adhezyjne...
-
Numerical modelling of DMT test in calibration chamber
PublicationAnaliza numeryczna badania DMT wykonanego w komorze kalibracyjnej w Katedrze Geotechniki Politechniki Gdańskiej. Badania przeprowadzono w piasku Lubiatowo średnio zagęszczonym i zagęszczonym przy składowej pionowej naprężenia 100 kPa. Modelowano proces wciskania ostrza dylatometru oraz fazę odkształcenia membrany. Analiza parametryczna uwzględnia wpływ wartości kąta tarcia wewnętrznego i dylatancji oraz modułu odkształcenia uzyskanych...