Filters
total: 954
-
Catalog
- Publications 421 available results
- Journals 151 available results
- Publishing Houses 2 available results
- People 20 available results
- Projects 4 available results
- Laboratories 1 available results
- e-Learning Courses 194 available results
- Events 1 available results
- Open Research Data 160 available results
Search results for: EN 1317
-
DLC coating doped with W in ring-on-ring sliding with water lubrication 20MPa/0.1m/s
Open Research DataWear tests in sliding friction of 1% W (tungsten) doped DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 20MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: WATER. Tribometer: PT-3. Overall test time >15h. The test was...
-
DLC coating doped with W in ring-on-ring sliding with water lubrication 10MPa/0.1m/s
Open Research DataWear tests in sliding friction of 1% W (tungsten) doped DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 10MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: WATER. Tribometer: PT-3. Overall test time >15h. The test was...
-
Video traffic data - Interchanges Podwarpie (S1-86) - Entry + exit lanes, Poland
Open Research DataThe data includes video traffic data registered with 4 video cameras on entry or exit lanes of the Podwarpie interchange within S1 expressway in Poland (interchange of expressway S1 and national road 86), located in the Silesian Agglomeration). The data covers the one day: 23.05.2017 (expressway S1).
-
Fiber optic displacement sensor with signal analysis in spectral domain
PublicationIn this paper, a study of a low-coherence fiber optic displacement sensor is presented. The sensor consisted of a broadband source whose central wavelength was either at 1310 nm or 1550 nm, a sensing Fabry-Pérot interferometer operating in reflective mode and an optical spectrum analyzer acting as the detection setup. All these components were connected by a single-mode fiber coupler. Metrological parameters of the sensor were...
-
Influence of temperature and interactions with ligands on dissociation of dsDNA and ligand-dsDNA complexes of various types of binding : an electrochemical study.
PublicationSeveral medicinally important compounds that bind to dsDNA strands via intercalation (C-1311, C-1305, EtBr), major groove binding (Hoechst 33258) and covalent binding (cis-Pt) were examined. The obtained results suggest that both the transfer of conformation B to C and the denaturation process, for the ligand-dsDNA complexes, except for covalently bound cis-Pt, took place at higher temperatures compared to the unbound helix. Furthermore,...
-
Combination of terrestrial laser scanning and UAV photogrammetry for 3D modelling and degradation assessment of heritage building based on a lighting analysis: case study—St. Adalbert Church in Gdansk, Poland
PublicationThe construction of the St. Adalbert Church in Gdansk dates to 1310. It is a church of rich history and great historical value, and its care is challenging. In this study, the combination of unmanned aerial vehicle (UAV) photogrammetry and terrestrial laser scanning (TLS) was used to accurately build a 3D model of the church. Together with the collected historical inventory documentation, the historic building information model...
-
Rheology studies of multiple times processed poly(lactic acid)-carbon black composites
Open Research DataThis dataset contains MFR/MVR (melt flow rate) rheology studies of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The study aims to observe structural differences and applied properties changes under multiple reprocessing of the composite material at different temperatures...
-
Real-Time Gastrointestinal Tract Video Analysis on a Cluster Supercomputer
PublicationThe article presents a novel approach to medical video data analysis and recognition. Emphasis has been put on adapting existing algorithms detecting le- sions and bleedings for real time usage in a medical doctor's office during an en- doscopic examination. A system for diagnosis recommendation and disease detec- tion has been designed taking into account the limited mobility of the endoscope and the doctor's requirements. The...
-
Projekt dwóch belek hybrydowych dla firmy H+H Polska sp. z o.o.
PublicationOpracowanie stanowi projekt dwóch belek nadprożowych o długości 3,0 m każda o przekroju poprzecznym belki hybrydowej (beton konstrukcyjny łączony z betonem komórkowym) nawiązującej do wymiaru bloczka z betonu komórkowego firmy H+H Polska sp. z o.o. o wymiarach (szerokość × wysokość × długość): 24 × 24 × 60 cm, odmiany D600 o średniej wytrzymałości na ściskanie 3,0 MPa (zgodnie z kartą techniczną w załączniku do opracowania). Całkowita...
-
Innovative cold-formed GEB section under compression
PublicationCold-formed steel sections extensively affect the modern steel construction industry. Not only are they used as secondary elements like purlins or sheeting, but also they can serve as primary load-bearing members in fabricated steel panels and trusses. A new cross-section called shortly a GEB may serve as that member. However, its existence of the metal building structures industry depends on the exact, optimal dimensional parameters...
-
Influence of nonlinearities on the efficiency and accuracy of FEM calculations on the example of a steel build-up thin-walled column
PublicationDue to the increase of computing capabilities of standard processing units, it is possible to perform complex analyses, considering a number of nonlinearities, such as geometric, material and boundary (contact) even on personal computers. In the paper, the authors have analysed the efficiency and accuracy of standard PC’s FEM calculations performed in Abaqus CAE 2017 software on the example of a critical load assessment of a thin-walled...
-
Naprężenia własne cienkich blach walcowanych
PublicationArtykuł traktuje o istotności uwzględniania naprężeń szczątkowych w analizie nośności elementów konstrukcyjnych z kształtowników giętych na zimno. Wpływ naprężeń własnych powstających w wyniku wytwarzania, transportu i montażu konstrukcji, w przypadku elementów wykonanych z cienkich arkuszy blach jest znaczący. Według [PN-EN-1993-1-1:2006] elementy cienkościenne, jako elementy o przekrojach klasy czwartej, ze względu na swoją...
-
Supporting development of the smart ship technology by CFD simulation of ship behavior in close to real operational conditions
PublicationThe shipping industry is at the milestone of technological development – autonomous ships. Involving smart technologies accelerates development of green and safe shipping. Also IMO regulations, especially EEDI en-hanced application of new technologies. Meeting economic and ecological requirements future ships need to be designed with respect to increased reliability and operational performance. Design process of ships may be improved...
-
Experimental research of the effect of face milling strategy on the flatness deviations
PublicationIn this paper the dependencies between face milling strategy of EN AW6082-T6 aluminum alloy samples, with difference thicknesses (6, 8, and 12 mm) and two cold rolling directions, and flatness deviations were presented. Three strategies of milling included different proportions of material removed from both sides of the plates. This approach allowed to control the proportions of residual surface stresses on both sides of the specimens,...
-
Verification of Selected Calculation Methods Regarding Shear Strength in Reinforced and Prestressed Concrete Beams
PublicationThe purpose of this article was an attempt to compare selected calculation methods regarding shear strength in reinforced and prestressed concrete beams. Several calculation methods were tested. This included codes: PN-EN 1992-1-1:2008 [1], ACI 318- 14 [2] and fib Model Code for Concrete Structures 2010 [3]. The analysis also consists of methods published in technical literature. Calculations of shear strengths were made based...
-
Technical Mechanics 2 (PG_00049753), I stop, En, [W,C], zima 22/23
e-Learning CoursesLectures and tutorials devoted to basic issues of Strength of Materials (stress and strain states, the Hook's law, geometrical properties of an area, bending, shearing, torsion, deflection lines of beams, buckling and yielding criteria).
-
DLC coating doped with W in ring-on-ring sliding with saline solution (0.9% wt.) lubrication 20MPa/0.1m/s
Open Research DataWear tests in sliding friction of 1% W (tungsten) doped DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 20MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9% wt.). Tribometer: PT-3. Overall test time >15h....
-
DLC coating doped with W in ring-on-ring sliding with saline solution (0.9% wt.) lubrication 10MPa/0.1m/s
Open Research DataWear tests in sliding friction of 1% W (tungsten) doped DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 10MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9% wt.). Tribometer: PT-3. Overall test time >15h....
-
Video traffic data - Interchange Lotnisko (S2-S79) - Exit +entry lanes, Poland
Open Research DataThe data includes video traffic data registered with 8 video cameras at entry or exit lanes of the Lotnisko interchange within S2 expressway in Poland (interchange of expressway S2 and expressway S79), located in the Warsaw Agglomeration. The data covers the one day: 05.09.2017 (expressway S2).
-
Radio Communication Antennas and MIMO Techniques (2023/24)
e-Learning CoursesCourse assigned to the following subject: - Radio Communication Antennas and MIMO Techniques (profile Radio Communication Systems and Networks [EN])
-
Implementation of SiN thin film in fiber-optic sensor working in telecommunication range of wavelengths
PublicationMirrors are used in optical sensors and measurement setups. This creates a demand for mirrors made of new materials and having various properties tailored to specific applications. In this work, we propose silicon covered with a thin silicon nitride layer as a mirror for near-infrared measurements. SiN layer was deposited on a standard silicon wafer with a Low-Pressure Chemical Vapor Deposition furnace. Then, the created layer...
-
Electrochemical formation of the adduct between antitumor agent C_1311 and DNA nucleoside dG. 75.
PublicationPrzyjmuje się, że metaboliczna aktywacja przeciwnowotworowej pochodnej C_1311 jest procesem koniecznym dla jej aktywności przeciwnowotworowej. Wykazano wcześniej, że taka aktywacja prowadzi do kowalencyjnego wiązania się leku z DNA w komórce nowotworowej. Aby zbadać molekularny mechanizm powyższej reakcji metabolicznej przeprowadzono badania elektrochemicznego utleniania pochodnej C_1311. Wykazano w pracy, że dwa produkty elektrochemicznego...
-
Handelingen van het Genootschap voor geschiedenis, gesticht onder de benaming 'Société d'Émulation' te Brugge: driemaandelijks tijdschrift voor de studie van geschiedenis en oudheden van Vlaanderen
Journals -
Handelingen van het Genootschap voor geschiedenis, gesticht onder de benaming 'Société d'Émulation' te Brugge: driemaandelijks tijdschrift voor de studie van geschiedenis en oudheden van Vlaanderen
Journals -
The operation mode of E/E/PE system and its influence on determining and verifying the safety integrity level = Rodzaj pracy systemu E/E/PE i jego wpływ na określanie i weryfikację poziomu nienaruszalności bezpieczeństwa
PublicationNorma PN-EN 61508 wprowadza kryteria probabilistyczne dla wyróżnionych rodzajów pracy systemów E/E/PE, które związane są z poziomami nienaruszalności bezpieczeństwa SIL. Dla systemów sterowania i zabezpieczeń, pracujących w trybie rzadkiego przywołania do działania, kryterium tym jest przeciętne prawdopodobieństwo niewypełnienia funkcji bezpieczeństwa na żądanie PFDavg. W przypadku systemów realizujących funkcje bezpieczeństwa...
-
Designate CTOD Heat Affected Zone of butt weld, Report No: WOiO/II/76/2013
PublicationTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
Designate CTOD of Weld Metal of butt weld, No WOiO/II/108/2013
PublicationTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
Wpływ zastosowania nakładek wzmacniających środnik na nośność i sztywność doczołowego węzła śrubowego.
PublicationCiągłe dążenie do upraszczania elementów konstrukcyjnych oraz znajdowania mniej czasochłonnych rozwiązań wykonawczo – montażowych wraz z nieuchronnym wzrostem kosztów robocizny determinują m.in. eliminację z procesów technologicznych tych etapów, które nie podlegają automatyzacji. Taką czynnością jest przede wszystkim spawanie dodatkowych wzmocnień i usztywnień węzłów w postaci żeber. Efektem wieloletnich badań jest metoda przedstawiona...
-
Designate of CTOD for WM and HAZ, report no: WOiO/II/122/2014
PublicationTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
CTOD designation for WM and HAZ in butt joint made from S460 ML steel, Expertise No. WOiO/II/82/2015
PublicationTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
WYKORZYSTANIE TECHNIK OLFAKTOMETRII TERENOWEJ I GC×GC-TOFMS DO OCENY UCIĄŻLIWOŚCI ZAPACHOWEJ POWIETRZA ATMOSFERYCZNEGO NA OBSZARACH PRZYLEGŁYCH DO SKŁADOWISKA ODPADOW KOMUNALNYCH W GDAŃSKU SZADÓŁKACH
PublicationW artykule przedstawiono wyniki badań przeprowadzonych na obszarach sąsiadujących ze składowiskiem odpadów komunalnych w Gdańsku-Szadółkach. Do oceny uciążliwości zapachowej powietrza atmosferycznego wykorzystano technikę olfaktometrii terenowej. Narzędziami, których wykorzystanie umożliwia badanie właściwości zapachowych odorantów występujących w powietrzu atmosferycznym in-situ są olfaktometry terenowe, których zastosowanie umożliwia...
-
Wpływ stanu zachowania materiału konstrukcyjnego na nośność zabytkowych drewnianych słupów, w żuławskich domach podcieniowych, z XVIII i XIX wieku.
PublicationPowstało wiele opracowań dotyczących zagadnień architektonicznych domów podcieniowych na Żuławach, ale brak na ten temat publikacji dotyczących problematyki techniczno-konserwatorskiej. Niniejszy artykuł jest fragmentem badań prowadzonych obecnie przez autora. Jest pierwszą próbą wykonania analizy statyczno- wytrzymałościowej wybranych, zabytkowych drewnianych podcieni z obszaru Delty Wisły, wraz z opisem stanu zachowania. W tekście...
-
Verification of punching shear outside the shear cap by the direct method
PublicationThe proposition of a method to verify the punching resistance for very large supports based on the EN 1992-1-1 standard is described in this paper. The present standard guidelines for the calculation of the punching resistance for large supports are also summarised. The proposed direct method is compared with other standard methods using an example taken from design practice. This method consists of a direct check of the shear...
-
Functional phase bistability in a nanocrystalline RbMn[Fe(CN)6] thin film fabricated by matrix-assisted laser evaporation
PublicationOne of the main barriers hindering applications of Prussian blue metal assemblies is their poor processability, which makes the fabrication of intact thin films very difficult. In this work, a nanocrystalline RbMn[Fe(CN)6]·xH2O film on silicon substrate was obtained for the first time via laser-stimulated deposition and investigated. Temperature-induced phase transition and bistability within broad hysteresis loop (120 K), along...
-
Głębokie Sieci Neuronowe Do Analizy Danych
e-Learning Courses{mlang pl}Kurs przeznaczony jest dla studentów kierunku Inżynieria Danych.{mlang} {mlang en}Course for Data Analysis students.{mlang}
-
UAV Survey Images - orthophotomap - Gdynia Container Terminal Day Light- MP2
Open Research DataDataset description: Raw images from photogrammetric survey. Object: Parking place near by Gdynia Container Terminal - day light photosLocation: Gdynia, Pomerania, PolandDrone type: DJI Mavic Pro 2Flight plan: Single GridTarget Product: OrthophotoDate: 15.10.2020Direct georeferencing: yesMetadata data: yes/GPSGCP: Yes - Description and position includedGCP...
-
Oprawy ze średniowiecznych rękopisów muzycznych w księgozbiorze Jana Bernarda Bonifacia = Medieval musical manuscript leaves as bookbindings in the book-collection of Giovanni Bernardino Bonifacio
PublicationNiniejsza praca zawiera analizę jakościową i ilościową zespołu analogów, składającego się z około 30 druków (XVI wiek), oprawionych w średniowieczne rękopisy muzyczne na pergaminie z zapisem neumatycznym (XIV/XV wiek) z księgozbioru Jana Bernarda Bonifacia (1517-1597), fundatora Biblioteki Rady Miejskiej w Gdańsku (Bibliotheca Senatus Gedanensis). W centrum interesowania autorki znalazły się wyżej wymienione oprawy, a w szczególności...
-
Oprawy ze średniowiecznych rękopisów muzycznych w księgozbiorze Jana Bernarda Bonifacia = Medieval musical manuscript leaves as bookbindings in the book-collection of Giovanni Bernardino Bonifacio
PublicationNiniejsza praca zawiera analizę jakościową i ilościową zespołu analogów, składającego się z około 30 druków (XVI wiek), oprawionych w średniowieczne rękopisy muzyczne na pergaminie z zapisem neumatycznym (XIV/XV wiek) z księgozbioru Jana Bernarda Bonifacia (1517-1597), fundatora Biblioteki Rady Miejskiej w Gdańsku (Bibliotheca Senatus Gedanensis). W centrum interesowania autorki znalazły się wyżej wymienione oprawy, a w szczególności...
-
ENG_Architectural Design sem 6_2022_2023_KAMiUP
e-Learning CoursesThe course concerns the shaping of marketplace facilities with accompanying functions. The course presents a multifaceted approach to the issues, including technical, legal, economic, environmental, and cultural issues. The aim of the course, based on a case study in Gdańsk (Marketplace Gdańsk-Wrzeszcz (Targowisko Gdańsk-Wrzeszcz) and its surroundings), is to understand the problem of regeneration of exhibition spaces and to develop...
-
Fully enzymatic mediatorless fuel cell with efficient naphthylated carbon nanotube-laccase composite cathodes
PublicationAn efficient, mediator-free enzymatic glucose/O2 biofuel cell with an oxygen intensive anode based on glucose dehydrogenase is presented. In the device,the power of the biofuel cell and electrode potentials of each of the enzymatic electrodes were monitored in parallel under the biofuel cell working conditions. The carbon nanotube composite biocathode demonstrates an almost constant electrode potential vs. saturated calomel electrode...
-
Influence of oxygenation of constructed wetlands for effectiveness of contaminants removal
PublicationBadania prowadzono w trzech hybrydowych systemach hydrofitowych (HSH): Wiklinie, Wieszynie i Wiedersbergu. Obiekty charakteryzowały się różnym ładunkiem doprowadzanej SO. Określenie jakości SO w ściekach polegało na przeprowadzeniu analizy specjacji substancji organicznej zgodnie z metodyką podaną w niemieckich wytycznych ATV-131. Na podstawie analizy frakcji ChZT wykazano, że szybkość rozkładu SO (k) w złożach była determinowana...
-
Video traffic data - Interchange Slowackiego (S8-Slowackiego), Poland
Open Research DataThe data includes video traffic data registered with 4 video cameras at entry or exit lanes of the Slowackiego interchange within S8 expressway in Poland (interchange of expressway S8 and Slowackiego street), located in the Warsaw Agglomeration. The data covers the one day: 10-11.05.2017 (expressway S8).
-
Video traffic data - Interchange Broniewskiego (S8-Broniewskiego), Poland
Open Research DataThe data includes video traffic data registered with 4 video cameras at entry or exit lanes of the Broniewskiego interchange within S8 expressway in Poland (interchange of expressway S8 and Broniewskiego street), located in the Warsaw Agglomeration. The data covers the two days: 10-11.05.2017 (expressway S8).
-
Wpływ zmian dopuszczalnych wartości parametrów geometrycznych i kinematycznych na podatność modernizacyjną układów torowych
PublicationPodatnością modernizacyjną nazywamy stopień przystosowania analizowanego odcinka linii kolejowej do zmiany prędkości eksploatacyjnej. Skala możliwych zmian prędkości (w sensie jej zwiększenia) jest wypadkową istniejącego układu geometrycznego linii w planie, ograniczeń lokalizacyjnych oraz dopuszczalnych wartości parametrów geometrycznych i kinematycznych. Jakiekolwiek zmiany tych ostatnich wpływają bezpośrednio na obliczenie elementarnych...
-
Verification of selected calculation methods regarding shear strength in beams without web reinforcement
PublicationThe purpose of the article was to compare selected calculation methods regarding shear strength in reinforced concrete beams without web reinforcement. Several calculation methods were tested. This included codes: PN-EN 1992-1-1:2008, ACI 318-14 and fib Model Code for Concrete Structures 2010. The analysis also consists of authorial methods published in technical literature. Calculations of shear strengths were made based on experimental...
-
Electrochemical simulation of enzymatic transformations studied for the selected antitumor acridine derivatives
PublicationThe elucidation of the metabolic pathways and the biotransformation mechanisms of potential drugs is a crucial point in drug development. It allows to know the activation routes of the new biologically active compounds, especially in respect to their possible toxicity. Generally, in vivo or in vitro experiments with liver microsomes or hepatocytes are performed. However, these testing schemes are tedious, time consuming and of...
-
Katedra Systemów i Sieci Radiokomunikacyjnych – punkt wymiany danych
e-Learning Courses{mlang en}The course constans general materials for bachelor and master degree students.{mlang}{mlang pl}Kurs zawiera materiały dla studentów I oraz II stopnia.{mlang}
-
Wydatki na opiekę zdrowotną a efekty zdrowotne – analiza porównawcza krajów europejskich metodą DEA
PublicationEfektywnie działające systemy ochrony zdrowia mają istotne znaczenie dla zapewnienia społeczeństwu jakości życia na odpowiednim poziomie. Średnie wydatki dla krajów UE wynosiły w 2000 r. 1836 dol., a w 2012 r. osiągnęły poziom 3317 dol. na osobę z uwzględnieniem parytetu siły nabywczej (Purchasing Power Parity, PPP). W krajach Europy Środkowo-Wschodniej nienależących do UE całkowite wydatki na zdrowie są znacznie niższe, a proporcja...
-
The Specific Nature of Chemical Composition of Water from Volcanic Lakes Based on Bali Case Study
PublicationThe research area was localized in the Indonesian Archipelago, at the latitude of eight and nine degrees S on the one of the Lesser Sunda group island provinces, Bali (563,3 km2). Two massive calderas (Mount Batur 1717 m above sea level.; Mount Sangiyang 2093 m above sea level) are one of the most prominent landforms in the chain of volcanic mountain ranges of the Bali Island. Lake Batur (17,18 km2) and Batur Spring (which are...
-
Podstawy eksploatacji maszyn i urządzeń energetycznych, L, EN, sem. 5, zima 22/23 (PG_00042066)
e-Learning Courses