Filtry
wszystkich: 1420
wybranych: 1094
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: DEGREE OF MICROPHASE SEPARATION
-
Comparison of the powers of energy losses in a variable capacity displacement pump determined without or with taking into account the power of hydraulic oil compression
PublikacjaPowers of energy losses in a variable capacity displacement pump are compared with or without taking into account the power of hydraulic oil compression. Evaluation of power of liquid compression in the pump was made possible by the use of method, proposed by the Author, of determining the degree of liquid aeration in the pump. In the method of determining the liquid aeration in the pump and of powers of volumetric losses of liquid...
-
Hard carbon derived from rice husk as low cost negative electrodes in Na-ion batteries
PublikacjaHere, we report the synthesis of hard carbon materials (RH) made from natural rice husk through a single pyrolysis process and their application as an anode in sodium-ion batteries. The studies show that the electrochemical properties of RHs are affected by the treatment temperatures, which determine the materials morphology, in particular, their degree of graphitization and extent of continuous channels (nanovoids). The latter...
-
ATTEMPT AT EVALUATING THE INFLUENCE OF BENDING STRESS ON SHAFT WEAR PROCESSES IN WATER LUBRICATED SLIDING BEARING WITH A RUBBER BUSHING
PublikacjaWater lubricated bearings find increasingly wide application in shipbuilding or hydro–power industry, the popularity stemming from their numerous advantages. Unfortunately, as it turns out, water lubricated bearings do not always meet expectations, as on occasion they become subject to intense, premature wear which requires costly repair. One of the still unexplained phenomena is the process of excessive bearing wear, in particular...
-
TOXICOLOGICAL ASSESSMENT OF FOOD PACKAGES EXTRACTS
PublikacjaIn the scientific literature related to the widely understood issue of packaging materials designed to have contact with food (Food Contact Materials – FCM) there is much information on raw materials used for their production, their physiochemical properties, types and parameters. There is also a great number of publications on the management and disposal of used packaging. Unfortunately, not much attention is given to the matters...
-
Finite element modeling of plastic hinges based on ductility demand-capacity method using nonlinear material for dynamic analysis
PublikacjaThe article discusses modeling plastic hinges in reinforced concrete interme-diate supports using finite elements methods. The ductility demand-capacitymethod was used to determine the geometrical parameters of cross-section plas-ticization zones, their ability to move and rotate, as well as their ductility. Dueto the varied geometry and stiffness of the supports and their nonlinear behav-ior under dynamic load, this method was...
-
Determination of moisture resistance of covered electrodes according to PN-EN ISO 14372
PublikacjaMoisture present in the electrode covering is one of the sources of diffusible hydrogen in welded joints. In order to study the diffusible hydrogen content in deposited metal, a stand for moisturizing covered electrodes, in accordance with the PN-EN ISO 14372 standard, was built. After the stand was completed, a test of moisturizing the electrodes was carried out and measurements of the diffusible hydrogen content in deposited...
-
A new technology of crude vegetable oil degumming with rhamnolipid solutions
PublikacjaA new technology of crude vegetable oil degumming is described. It is based on rhamnolipid biocomplex solution application for phosphatides removal. The rhamnolipid biocomplex produced by Pseudomonas sp. PS-17 was used as biosurfactant. Rapeseed oil was used in all experiments. First, it was degummed with H2SO4 in order to remove all phosphatides and then 1% (w/w) of granular soybean lecithin was added. Model oil was treated with...
-
Employing a biofeedback method based on hemispheric synchronization in effective learning
PublikacjaIn this paper an approach to build a brain computer-based hemispheric synchronization system is presented. The concept utilizes the wireless EEG signal registration and acquisition as well as advanced pre-processing methods. The influence of various filtration techniques of EOG artifacts on brain state recognition is examined. The emphasis is put on brain state recognition using band pass filtration for separation of individual...
-
Current trends in analytical strategies for determination of polybrominated diphenyl ethers (PBDEs) in samples with different matrix compositions – Part 1.: Screening of new developments in sample preparation
PublikacjaPolybrominated diphenyl ethers (PBDEs) are ubiquitous compounds in the environment. Restrictions on the use of PBDEs introduced at the beginning of the 21st century have not eliminated these highly persistent and bioaccumulative compounds from the environment. Despite many existing regulations to control and phase out, extensive research on PBDEs is still necessary to fully evaluate the hazard their create to the environment. In...
-
The effect of full-cell impregnation of pine wood (Pinus Sylvestris L.) on the fine dust content during sawing on a frame sawing machine
PublikacjaIn this paper the results of the analysis of the effect of the impregnation treatment of pine wood on the granularity of sawdust from the sawing process on the frame sawing machine PRW 15M are presented. Granulometric analyses of chips from impregnated and unimpregnated pine wood implies that the impregnation of pine wood does not affect the size and structure of the sawdust produced. A major ≈ 95% share of the formed chips is...
-
SPECTRAL-BASED MODAL PARAMETERS IDENTIFICATION WITH MULTIPLE PARTICLE SWARMS OPTIMIZATION
PublikacjaThe paper presents usage of a Particle Swarm Optimization [1] based algorithm for spectral-based modal parameters identification. The main algorithm consists of two groups of swarms, namely, scouts and helpers. For the first group additional penalizing process is provided to force separation of scouting swarms in frequency space. The swarms have an ability to communicate with each other. At first stage, each swarm focuses on a...
-
Physical and Thermophysical Properties of 1-Hexyl-1,4-diaza[2.2.2]bicyclooctanium Bis(trifluoromethylsulfonyl)imide Ionic Liquid
PublikacjaOwing to their unique properties, ionic liquids (ILs) have become a real alternative to organic compounds. Nowadays, ILs are commonly used in a number of areas such as chemical synthesis and separation techniques. However, ionic liquids continue to have a limited applicability in industry because the information on their physical and chemical properties is not readily available. This paper presents, for the first time, the results...
-
Cuticular lipids of insects as potential biofungicides
PublikacjaThe term ''lipids'' refers to fatty acids, their derivatives and substances related with them biochemically or by the functions in the body. Lipids include compounds with different chemical structure. There are lipids with structures based on long-chain carboxylic acids and their direct derivatives, namely: fatty acids, alkanes, some alkenes, aldehydes and long chain alcohols and their derivatives (esters). The variety of lipid...
-
Distillation cleanup preceded gc determination of short-chain monocarboxylic acids in aqueous and solid samples of wastewater origin = Oznaczanie krótkołańcuchowych kwasów monokarboksylowych w próbkach wodnych i stałych pochodzących z oczyszczalni ścieków z wykorzystaniem chromatografii gazowej poprzedzonej destylacją
PublikacjaShort-chain monocarboxylic acids (SCMAs) (C2-C5) formed in the process of aerobic biodegradation of larger organic molecules should often be monitored to optimize wastewater biological treatment and study the processes of converting organic waste matter into methane, etc. Gas chromatography (GC) seems a method of choice for such a task. Majority of samples require clean up before they can be injected into GC system. In this work...
-
Determination of terpene profiles in potential superfruits
PublikacjaThe aim of this work was to characterize and compare the profiles of volatile terpenes in four potential superfruits. These profiles were determined using headspace solid-phase microextraction coupled with comprehensive two-dimensional gas chromatography linked to time-of-flight mass spectrometry. The proposed technique allowed the separation and identification of 79 terpenes present in cape gooseberry, crabapple, cherry silver...
-
Method for Clustering of Brain Activity Data Derived from EEG Signals
PublikacjaA method for assessing separability of EEG signals associated with three classes of brain activity is proposed. The EEG signals are acquired from 23 subjects, gathered from a headset consisting of 14 electrodes. Data are processed by applying Discrete Wavelet Transform (DWT) for the signal analysis and an autoencoder neural network for the brain activity separation. Processing involves 74 wavelets from 3 DWT families: Coiflets,...
-
Photoconduction and magnetic field effect on photoconduction in hole-transporting star-burst amine (m-MTDATA) films
PublikacjaPhotoconduction and magnetic field effect on photoconduction have been investigated as a function of electric field strength, excitation light intensity and wavelength in vacuum evaporated films of m-MTDATA (4,4′,4″-tris(N-(3-methylphenyl)-N-phenylylamino) triphenylamine), the starburst amine commonly used as hole-transporting material in organic light-emitting diodes. The photocurrent is found to be generated by the singlet exciton...
-
Pervaporation Zeolite-Based Composite Membranes for Solvent Separations
PublikacjaThanks to their well-defined molecular sieving and stability, zeolites have been proposed in selective membrane separations, such as gas separation and pervaporation. For instance, the incorporation of zeolites into polymer phases to generate composite (or mixed matrix) membranes revealed important advances in pervaporation. Therefore, the goal of this review is to compile and elucidate the latest advances (over the last 2-3 years)...
-
Introduction to the special issue on machine learning in acoustics
PublikacjaWhen we started our Call for Papers for a Special Issue on “Machine Learning in Acoustics” in the Journal of the Acoustical Society of America, our ambition was to invite papers in which machine learning was applied to all acoustics areas. They were listed, but not limited to, as follows: • Music and synthesis analysis • Music sentiment analysis • Music perception • Intelligent music recognition • Musical source separation • Singing...
-
MXene-based materials for removal of antibiotics and heavy metals from wastewater– a review
PublikacjaAs a novel family of 2D materials, MXenes provide an extensive variety of applications in water and effluent treatment due to their distinctive properties and attractive applicability, including superior electrical conductivity, higher thermal stability, hydrophilicity, and high sorption-reduction capacity. Their excellent sorption selectivity makes them perfect for removing hazardous contaminants. Currently, MXene-based materials...
-
Fully Separated Flow Control Using DBD Plasma Actuators Located at the Leading Edge of an Airfoil
PublikacjaIn the framework of the PLASMAERO European project, experiments were conducted to investigate the authority of surface DBD plasma actuators to alter a fully separated flow around an airfoil in order to improve its aerodynamic performances in its natural stall regime. In this paper, unsteady excitation control is more specifically investigated. The key control parameter studied here is the burst frequency which periodically imposes...
-
Adaptation of the arbitrary Lagrange–Euler approach to fluid–solid interaction on an example of high velocity flow over thin platelet
PublikacjaThe aim of this study is to analyse the behaviour of a thin plate with air flow velocities of 0.3–0.9 Ma. Data from the experiment and numerical tools were used for the analysis. For fluid–solid interaction calculations, the arbitrary Lagrange–Euler approach was used. The results of the measurements are twofold. The first one is the measurement of the flow before and after vibrating plate, i.e. pure flow plate, and the second consists...
-
Równolegle przebiegające procesy separacji pianowej jonów Al(III), Cu(II) i Zn(II) z roztworów ich mieszanin
PublikacjaMetody flotacji jonowej i precypitacyjnej należą do procesów separacji pianowej, wykorzystujących zdolność selektywnej adsorpcji niektórych składników roztworu na powierzchni międzyfazowej gaz – ciecz. Do zalet separacji pianowej zalicza się m.in. niewysokie koszty inwestycyjne i eksploatacyjne oraz wysoką skuteczność w obróbce roztworów rozcieńczonych. Celem pracy jest ocena wpływu kluczowych parametrów na wydajność i przebieg...
-
AUTOMATIC OPTIMIZATION OF ADAPTIVE NOTCH FILTER’S FREQUEN CY TRACKING
PublikacjaEstimation of instantaneous frequency of narrowband com- plex sinusoids is often performed using lightweight algo- rithms called adaptive notch filters. However, to reach high performance, these algorithms require careful tuning. The paper proposes a novel self-tuning layer for a recently intr o- ducedadaptive notch filtering algorithm. Analysis shows th at, under Gaussian random-walk type assumptions, the resultin g solution converges...
-
Automatic Optimization Of Adaptive Notch Filter’s Frequency Tracking
PublikacjaEstimation of instantaneous frequency of narrowband com- plex sinusoids is often performed using lightweight algo- rithms called adaptive notch filters. However, to reach high performance, these algorithms require careful tuning. The paper proposes a novel self-tuning layer for a recently intr o- ducedadaptive notch filtering algorithm. Analysis shows th at, under Gaussian random-walk type assumptions, the resultin g solution converges...
-
Experimental ultimate strength assessment of stiffened plates subjected to marine immersed corrosion
PublikacjaThis study experimentally analyses the impact of marine immersed corrosion degradation on the compressive strength of the stiffened plates where the lower degradation levels were considered. The corrosion degradation test was accelerated by controlling the natural corrosion environmental factors, avoiding applying an electric current. Different groups of corrosion degradation levels and initial plate thicknesses were investigated....
-
INDICES FOR ASSESSING POTENTIAL ENVIRONMENTAL HAZARD FROM FUTURE SHIP SCRAPPING PROCESS, DETERMINABLE IN SHIP DESIGN STAGE
PublikacjaThis paper shortly presents the issue of utilization of ships after their withdrawal from service. Information on number of floating units liquidated in previous years was presented. Hazards to the environment , health and life of workers employed in the Far East ship scrapping yards operating on the beaches, were indicated. Then, the most important rules which have to make the ship recycling process safe were referred to. This...
-
The Method of a Two-Level Text-Meaning Similarity Approximation of the Customers’ Opinions
PublikacjaThe method of two-level text-meaning similarity approximation, consisting in the implementation of the classification of the stages of text opinions of customers and identifying their rank quality level was developed. Proposed and proved the significance of major hypotheses, put as the basis of the developed methodology, notably about the significance of suggestions about the existence of analogies between mathematical bases of...
-
Movement perception with the use of a motorized delta armrest and virtual reality
PublikacjaIn this paper we present a combination of neuroscience experiments with the use of a parallel armrest robot to study the effects of temporal delays and spatial biases on the movement perception. A dedicated armrest to guide and manipulate the arm has been developed for these experiments. It is a three-degree-of-freedom Delta structure. In combination with a virtual reality application, the movement perception has been evaluated....
-
Dual functionality of amphiphilic 1-alkyl-3-methylimidazolium hydrogen sulfate ionic liquids: surfactants with catalytic function
PublikacjaA series of amphiphilic 1-alkyl-3-methylimidazolium hydrogen sulfate ionic liquids were synthesized. Acidic hydrogen sulfate ionic liquids with the alkyl chains C6–C14 are characterized by good surface properties. Their surface properties (adsorption and micellization parameters, degree of ionization of micelles, Krafft temperatures and thermodynamic parameters) were determined. Synthesized ionic liquids were applied as a co-catalyst...
-
PREPARATION AND CHARACTERIZATION OF CoFe2O4/TiO2-PANI HYBRID NANOCOMPOSITE WITH MAGNETIC AND PHOYOCATALYTIC ACTIVITY
PublikacjaHybrid nanocomposites consisting of inorganic component and organic conducting polymer are promising materials, which can be applied in heterogeneous photocatalysis. Titanium(IV) oxide is widely used photocatalysts due to its non-toxicity, low cost and chemical stability. The main disadvantage of TiO2 is low photocatalytic activity under visible light. Conducting polymers, also known as conjugated polymers are polymer materials...
-
Magnetic photocatalysts for water treatment
PublikacjaThe concept of magnetic photocatalysts with separation function requires ferromagnetic material with high magnetic susceptibility to an external magnetic field to enable recycling of composite nanoparticles. Currently, much attention is devoted to functionalization of photocatalyst using MFe2O3, where M =Fe, Zn, Co, Mn. However direct contact between photocatalyst and magnetic iron oxide particles leads to photodissolution of iron...
-
A conceptual design and numerical analysis of the mixerless urea-SCR system
PublikacjaIn the present study, an innovative design of the urea-selective catalytic reduction (SCR) system without conventional mixing elements was developed. The aim was to obtain a high degree of urea decomposition, and uniform ammonia distribution at the inlet to the catalyst, while minimising the liquid film deposition and keeping the compact design. The concept of the design was based on creating high turbulences and elongating...
-
Characterization of small and medium enterprises (SMES) of Pomeranian Region in six sigma methodology application
PublikacjaThe paper presents the rarely researched and important issue for SMEs competitiveness - knowledge and practical application of Six Sigma methodology. The results of research conducted by Authors allow to answer the question - to what degree SMEs of Pomeranian region are aware of importance and prepared for systemic control and improvement of their processes?W opracowaniu poruszono istotne, z punktu widzenia podnoszenia konkurencyjności...
-
Towards automating repairs of IT systems
PublikacjaThis paper presents formal description of working principles of the repair library, being the essential component of the Repair Management Framework (RMF), which aims at automating the process of repairing IT systems, and consists also of the Repair Management Model (RMM) and the Repair Management System (RMS). RMM introduces two mathematical models (model of monitoring and model of repair processes), general enough to cover the...
-
Design of a microrobotic wrist for needle laparoscopic surgery
PublikacjaThe paper addresses the design of a micro wrist for needle laparoscopic surgery (needlescopy) using MEMS technology and an original 3 degree of freedom, 3D architecture. Advancement in needlescopy drives the development of multi-dof micro-tools 1-2mmin diameter with 3D mobility but standard available fabricationtechniques are for 2.5D structures. The paper discusses thedevelopment steps and design solutions for the realization...
-
Use of the AHP Method for Preference Determination in Yacht Design
PublikacjaA sailing yacht is a human-centred product, the design of which revolves primarily around the wants and desires of the future owner. In most cases, these preferences are not measurable, such as a personal aesthetic feeling, or a need for comfort, speed, safety etc. The aims of this paper are to demonstrate that these preferences can be classified and represented numerically, and to show that they are correlated with the type...
-
Preeclampsia Risk Prediction Using Machine Learning Methods Trained on Synthetic Data
PublikacjaThis paper describes a research study that investigates the use of machine learning algorithms on synthetic data to classify the risk of developing preeclampsia by pregnant women. Synthetic datasets were generated based on parameter distributions from three real patient studies. Four models were compared: XGBoost, Support Vector Machine (SVM), Random Forest, and Explainable Boosting Machines (EBM). The study found that the XGBoost...
-
Use of the AHP Method for Preference Determination in Yacht Design
PublikacjaA sailing yacht is a human-centred product, the design of which revolves primarily around the wants and desires of the future owner. In most cases, these preferences are not measurable, such as a personal aesthetic feeling, or a need for comfort, speed, safety etc. The aims of this paper are to demonstrate that these preferences can be classified and represented numerically, and to show that they are correlated with the type of...
-
A Framework of A Ship Domain-Based Near-Miss Detection Method Using Mamdani Neuro-Fuzzy Classification
PublikacjaSafety analysis of navigation over a given area may cover application of various risk measures for ship collisions. One of them is percentage of the so called near- miss situations (potential collision situations). In this article a method of automatic detection of such situations based on the data from Automatic Identification System (AIS), is proposed. The method utilizes input parameters such as: collision risk measure based...
-
Analysis of balancing of four stroke V6 engines
PublikacjaAnalysis of balance of V6 engines with a common-pin crankshaft depending on a cylinder bank angle and the crank radius to connecting rod length ratios , based on the relations derived, is presented in the paper. The bank angles providing the lowest moment of inertia forces in reciprocating motion, for selected values, were determined. The position of the plane of the main counterweights in order to maximum balance of the moment...
-
Hydrogen effects in duplex stainless steel welded joints - electrochemical studies
PublikacjaIn this work results on the influence of hydrogen on passivity and corrosion resistance of 2205 duplex stainless steel (DSS) welded joints are described. The results were discussed by taking into account three different areas on the welded joint: weld metal (WM), heat-affected zone (HAZ) and parent metal. The corrosion resistance was qualified with the polarization curves registered in a synthetic sea water. The conclusion is that,...
-
Sewage sludge pretreatment by low thermal disintegration for better efficacy of sludge digestion process
PublikacjaThe wastewater water treatment plant (WWTP) sector and it is developing technologies strive to be implement circular economy. The methane production from the sludge digestion process constitute promising source of the renewable energy for WWTP and approaching circular economy assumptions. For this reason, the objective of the study was to examine the modification of sludge characteristics due to the low temperature pretreatment....
-
2-Coloring number revisited
Publikacja2-Coloring number is a parameter, which is often used in the literature to bound the game chromatic number and other related parameters. However, this parameter has not been precisely studied before. In this paper we aim to fill this gap. In particular we show that the approximation of the game chromatic number by the 2-coloring number can be very poor for many graphs. Additionally we prove that the 2-coloring number may grow...
-
A novel heterogeneous model of concrete for numerical modelling of ground penetrating radar
PublikacjaThe ground penetrating radar (GPR) method has increasingly been applied in the non-destructive testing of reinforced concrete structures. The most common approach to the modelling of radar waves is to consider concrete as a homogeneous material. This paper proposes a novel, heterogeneous, numerical model of concrete for exhaustive interpretation of GPR data. An algorithm for determining the substitute values of the material constants...
-
Development and Research of the Text Messages Semantic Clustering Methodology
PublikacjaThe methodology of semantic clustering analysis of customer’s text-opinions collection is developed. The author's version of the mathematical models of formalization and practical realization of short textual messages semantic clustering procedure is proposed, based on the customer’s text-opinions collection Latent Semantic Analysis knowledge extracting method. An algorithm for semantic clustering of the text-opinions is developed,...
-
Nitrogen conversion during treatment of various type of wastewater in multistage treatment wetlands
PublikacjaThe objective of this investigation was to recognize nitrogen speciation during wastewater treatment in three multistage TWs (MTWs), which are assuming more a most effective in nitrogen removal than single stage TWs. Carried out investigations and analysis enable for determination of conditions, relationships and processes responsible for nitrogen conversions in subsequent stages of MTWs. In treated wastewater and reject water...
-
Algorithms for testing security in graphs
PublikacjaIn this paper we propose new algorithmic methods giving with the high probability the correct answer to the decision problem of security in graphs. For a given graph G and a subset S of a vertex set of G we have to decide whether S is secure, i.e. every subset X of S fulfils the condition: |N[X] \cap S| >= |N[X] \ S|, where N[X] is a closed neighbourhood of X in graph G. We constructed a polynomial time property pseudotester based...
-
Examination of selected failure criteria with asymmetric shear stresses in the collapse analysis of laminated shells
PublikacjaThe paper is concerned with failure analysis of composite shells performed with the usage of the nonlinear 6‐parameter shell theory with drilling rotation degree of freedom. This special theory embodies naturally unlim-ited translations and rotations and is suitable for analysis of irregular shells for instance with various, partic-ularly orthogonal, intersections. The presence of the drilling rotation is inherently accompanied...
-
Modified Preisach model of hysteresis in multi air gap ferrite core medium frequency transformer
PublikacjaThis article presents the modified Preisach model of hysteresis for a 3-phase medium frequency transformer in a 100 kW dual active bridge converter. The transformer magnetic core is assembled out of ferrite I-cores, which results in multiple parasitic air gaps. For this transformer, the hysteresis loops were measured and parameters of the Preisach model were determined. The Preisach distribution function is approximated with a...