Filtry
wszystkich: 2897
wybranych: 1987
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: AIR EXCESS RATIO
-
Experimental tuning of AuAg nanoalloy plasmon resonances assisted by machine learning method
PublikacjaPlasmonic nanostructures based on AuAg nanoalloys were fabricated by thermal annealing of metallic films in an argon atmosphere. The nanoalloys were chosen because they can extend the wavelength range in which plasmon resonance occurs and thus allow the design of plasmonic platforms with the desired parameters. The influence of initial fabrication parameters and experimental conditions on the formation of nanostructures was investigated....
-
Nitrogen mass balance and mathematical model of a Structured- Bed Reactor (SBRRIA)
PublikacjaAn up-flow structured-bed reactor subjected to recirculation and intermittent aeration (SBRRIA) was operated under varying influent conditions. The influent COD/N ratio was adjusted by maintaining a stable organic loading rate (average of 1.07 kgCOD m-3 d-1) and changing the nitrogen loading rate from 0.1 to 0.4 kg N m-3. Therefore, three different COD/N ratios were tested: 9.7±1 (Scenario 1); 7.6±1 (Scenario 2) and 2.9±1 (Scenario...
-
Thermo-Chemical Decomposition Study of Polyurethane Elastomer Through Glycerolysis Route with Using Crude and Refined Glycerine as a Transesterification Agent
PublikacjaDue to the increasing amount of polyurethane waste, chemical recycling of these materials is a topic of growing interest for many researchers. The primary pur- pose of polyurethane feedstock recycling is to recover the starting polyol. In this study glycerolysis using glycerine from two sources and two purity grades is proposed as a method of chemical recycling. The main effort of this paper focuses on the employment of commercial...
-
A Broadband Circularly Polarized Wide-Slot Antenna with a Miniaturized Footprint
PublikacjaThis letter presents a novel and simple feeding technique for exciting orthogonal components in a wide-slot antenna. In this technique, a rectangular bracket-shape parasitic strip is placed at the open end of the straight microstrip line to excite the fundamental horizontal and vertical components of the circular polarization (CP). The proposed technique—when employed in conjunction with the asymmetrical geometry of coplanar waveguide...
-
Deep eutectic solvents based highly efficient extractive desulfurization of fuels – Eco-friendly approach
PublikacjaThe developed process is based on alternative, green and cheap solvents for efficient desulfurization of fuels. Several deep eutectic solvents (DESs) were successfully synthesized and studied as extraction solvents for desulfurization of model fuel containing thiophene (T), benzothiophene (BT) and dibenzothiophene (DBT). The most important extraction parameters (i.e. kind of DES, DES: fuel volume ratio, hydrogen bond acceptor:...
-
Modeling of Passive and Forced Convection Heat Transfer in Channels with Rib Turbulators
PublikacjaThe main goal of the research presented in this paper was the experimental and numerical analysis of heat enhancement and aerodynamic phenomena during air flow in a channel equipped with flow turbulators in the form of properly configured ribs. The use of ribs intensifies the heat transfer and at the same time increases not only the flow resistance but also the energy costs. Therefore, designing modern heat exchangers with optimal...
-
Spectral Analysis of Capital Markets
PublikacjaIn this paper the problem of cycles existence in capital markets is addressed. A spectral analysis algorithm, which reduces signal-to-noise ratio, is proposed to derive cycle periodograms for the yield function of DJIA, WIG~20, and NIKKEI 225 indices. Peaks of the the periodograms provide premises to postulate the existence of some possible cycles. The 3.5 year periodicity in all 3 indices, which can be related to Kitchin cycle...
-
The Effect of Long Term Service at Elevated Temperatures on Microstructure Degradation of Austenitic Reformer Tubes
PublikacjaThe paper analyses the relationship between an increase of the inner diameter of tubes made of Manaurite XM cast steel and transformations occurring in their microstructure due to long-lasting operation in methane reformer. Examinations included metallographic analysis with light microscope (LM), scanning electron microscope (SEM) and microanalysis of the chemical composition of precipitates (EDX). It was indicated that there is...
-
Production of self-compacting concrete using limestone powder
PublikacjaAlthough there are visible signs of its gradual acceptance in North Africa through its limited use in construction, Libya has yet to explore the feasibility and applicability of self-compacting concrete (SCC) in new construction. The current study revolves around SCC made of locally available materials and the harsh environmental conditions. This paper deals with the investigation into the effect of the water to powder ratio and...
-
Experimental research on helical coil biomass boiler with oil as a heating fluid
PublikacjaThis paper presents an experimental research of helical coil biomass boiler with thermal oil heating agent. Heat exchanger consists of two coaxial helical coils swept by the flue gases. The burner is a single vertical retort connected to the fuel tank (wooden pellets). The boiler is a part of micro-power plant in which the heat from the boiler is exchanged with low-boiling HFE7100 to produce steam for a custom steam turbine. The...
-
Influence of Annealing Atmospheres on Photoelectrochemical Activity of TiO2 Nanotubes Modified with AuCu Nanoparticles
PublikacjaIn this article, we studied the annealing process of AuCu layers deposited on TiO2 nanotubes (NTs) conducted in various atmospheres such as air, vacuum, argon, and hydrogen in order to obtain materials active in both visible and UV–vis ranges. The material fabrication route covers the electrochemical anodization of a Ti plate, followed by thin AuCu film magnetron sputtering and further thermal treatment. Scanning electron microscopy...
-
Effect of the North Atlantic Thermohaline Circulation on changes in climatic conditions and river flow in Poland
Publikacja: The purpose of this study is to find connections between the North Atlantic Thermohaline Circulation (NA THC), climate elements, such as cloud cover, precipitation, air temperature, sunshine duration, and relative humidity, and flow of rivers in Poland. The intensity of NA THC was characterized by the DG3L index, which was established to assess changes in the amount of heat transported by NA THC along with the transport of water...
-
Gas turbines – technological development and potential use in CAES systems
PublikacjaThis article briefly describes Compressed Air Energy Storage (CAES), focusing on the technological development of one of the key elements of such systems – the gas turbines. It presents the basic parameters and features of gas turbines, as well as turbine classes with example models. Main tendencies in the structural and technological development are discussed. Changes and trends on electric energy markets are becoming more and...
-
Analytics of airport runoff water samples
PublikacjaThe everyday activities at airports, such as aircraft and ground vehicle washing, cleaning, de/anti-icing operations, fuelling, and fuel combustion, removing weeds are the main sources of airport industrial wastes. Runoff waters from airport areas constitute a serious environmental problem as they contribute to air, water, and soil pollution. The paper supplies general information on the technologies for treating airport runoff...
-
Research on the phenomena of warming up and free cooling down the car engine
PublikacjaThe average cold start temperature in Europe is 9 degrees C. However, not the average is the most important for the composition of exhaust gases and associated air pollution. The most onerous for the environment are the winter starts when automotive emissions of harmful gases add up in cities with those of home heating systems. The paper presents preliminary studies of warming up and cooling down processes in various environmental conditions....
-
Wpływ właściwości czynników chłodniczych na straty egzergii w pompie ciepła (Influence of Refrigerants Properties for Exergy Losses in Heat Pump)
PublikacjaArtykuł poświęcony jest wpływowi występujących w pompie ciepła strat egzergii na jej efektywność energetyczną, a co za tym idzie koszty funkcjonowania instalacji. Autorzy prezentują tu metodologię obliczeniową, która może być zastosowana w procesach projektowania układów cieplno-przepływowych. Obliczenia zostały wykonane na podstawie typowego układu powietrznej pompy ciepła pracującej w klimacie środkowo-europejskim. Ponadto w...
-
System sejsmiki refleksyjnej do poszukiwania morskich złóż węglowodorowych
PublikacjaW poszukiwaniu morskich złóż węglowodorowych wykorzystywane są różne metody zaliczane do tzw. sejsmiki refleksyjnej. Jedną z nich jest wykorzystanie systemu sejsmiki refleksyjnej holowanego za statkiem specjalistycznym przeznaczonym do badań sejsmicznych. Jest to złożony ruchomy układ techniczny składający się z wielu elementów składowych, takich jak: system wzbudzania fal akustycznych, system rejestracji odbijanych fal akustycznych...
-
Cross-linked epoxy-isocyanate blends containing Epidian-6 modified by glycols
PublikacjaPolymeric films of cross-linked structure may be formed using epoxy-isocyanate blends composed of Epidian-5 epoxy resin, 4,4’-diphenylmethanediisocyanate (MDI), Z-1 polyamine hardener and Epidian-6 epoxy resin modified by glycols. The effect of the component natures and ratio, process temperature and time on the gel-fraction content, as well as film hardness, was examined. The chemistry of the film forming process was determined...
-
Capacitively coupled ECG measurements - a CMRR circuit improvement
PublikacjaA typical galvanic-connected electrocardiogram (ECG) measurement system utilizes two signal’s electrodes and a third one in driven-right-leg (DRL) circuit for improving a common-mode rejection ratio(CMRR) of the acquisition system. In capacitive-coupled ECG similar techniques are used, however it is expected, that the utilized DRL subsystem is formed using a capacitive coupling approach, too. An improvement of the acquisition system...
-
Trichloridobis(ethyldiphenylphosphine)-(tetrahydrofuran)molybdenum(III)
PublikacjaIn the mononuclear title compound, [MoCl3(C4H8O)(C14H15P)2], obtained by the reaction of trichlorotris(tetrahydrofuran)molybdenum(III) and ethyldiphenylphosphine in tetrahydrofuran (THF) solution, the MoIII atom is six-coordinated by one O atom of a THF molecule, two P atoms from two ethyldiphenylphosphine ligands and three Cl atoms in a distorted octahedral geometry. The C atoms of the THF molecule are disordered over two positions...
-
Interpolator wykorzystujący filtr z maskowaniem charakterystyki częstotliwościowej
PublikacjaInterpolator o dużej krotności wymaga stosowania dolnoprzepustowych filtrów cyfrowych o bardzo wąskim paśmie przejściowym. Przekłada się to na dużą złożoność obliczeniową i problemy z projektowaniem filtrów interpolacyjnych. W pracy zaproponowano użycie metody FRM rozbijającej filtr o wąskim paśmie przejściowym na grupę filtrów o obniżonych wymaganiach, co zmniejsza liczbę niezerowych współczynników. W rezultacie użycie tego rozwiązania...
-
Pressure pulsations in turbine blade seal clearance
PublikacjaThe paper presents the results of numerical and experimental investigations into pressure forces generated in a turbine labyrinth seal. The experiments were performed on a single-stage air model turbine of the impulse type, while the numerical results were obtained by means of CFD Fluent Code. The performed experimental research and numerical calculations prove that in a shroud clearance the pressure pulsates and the effects of...
-
Passive sampling and/or extraction techniques in environmental analysis: a review
PublikacjaThe current state-of-the-art of passive sampling and/or extraction methods for long-term monitoring of pollutants in different environmental compartments is discussed in this review. Passive dosimeters that have been successfully used to monitor organic and inorganic contaminants in air, water, sediments, and soil are presented. The application of new approaches to the determination of pollutants at the sampling stage is discussed....
-
Monoterpenes emissions from different samples of wood-based materials – laminated chipboards and medium-density fiberboards (MDF)
PublikacjaThe paper presents the results of studies on emission rates of monoterpenes, carried out with the use of a new type of device - Markes’ Micro-Chamber/Thermal Extractor™ (μ-CTE250). Subject of studies were different types of wood-based materials such as: laminated chipboards and medium-density fiberboards (MDF). Based on the results obtained one can conclude that the laminated chipboards may affect the indoor air quality in much...
-
Improved methods for stator end winding leakage inductance calculation
PublikacjaCalculating the stator end-winding leakage inductance, taking into account the rotor, is difficult due to the irregular shape of the end-winding. The end-winding leakage may distribute at the end of the active part and the fringing flux of the air gap. The fringing flux belongs to the main flux but goes into the end-winding region. Then, not all the magnetic flux occurring in the end region is the end-winding leakage flux. The...
-
Numerical and experimental investigation of thermal convection near electric devices with vertical channels
PublikacjaThis paper presents the results of numerical and experimental investigation of thermal convection near heat emitting surfaces of an electric device. For the intensification of thermal convection, special vertical channels were formed near the heat emitting surfaces of the device. An experimental test has proved that there is an optimal length of the channels – thermal convection is the most intensive then. Air velocity vectors...
-
Weldability of S460ML High Strength Low Alloy Steel in Underwater Conditions
PublikacjaThe paper presents experimental evaluation of susceptibility of the high strength S460ML steel to cold cracking in the conditions of wet welding with the use of covered electrodes. From the results of Tekken tests it was found out that the investigated steel was characterised, in the conditions of the carried out experiments (underwater wet welding and air welding with rutile electrodes), of high susceptibility to cold cracking....
-
A LABORATORY STAND FOR THE ANALYSIS OF DYNAMIC PROPERTIES OF THERMOCOUPLES
PublikacjaIn the present elaboration, problems connected with measurements of high variable temperatures of gases are introduced and the impact of dynamic properties of different construction solutions of thermoelements on the accuracy of the measurements is considered. A laboratory stand built within research under doctoral thesis, destined for analysis of dynamic properties of thermocouples is also described. Results of numerical simulation...
-
Consumer Bankruptcy Prediction Using Balanced and Imbalanced Data
PublikacjaThis paper examines the usefulness of logit regression in forecasting the consumer bankruptcy of households using an imbalanced dataset. The research on consumer bankruptcy prediction is of paramount importance as it aims to build statistical models that can identify consumers in a difficult financial situation that may lead to consumer bankruptcy. In the face of the current global pandemic crisis, the future of household finances...
-
The impact of slowly biodegradable organic compounds on the oxygen uptake rate in activated sludge systems
PublikacjaThe hydrolysis process of slowly biodegradable substrate (Xs) have impact on the efficiencies of nutrient removal in activated sludge systems. Measurement of OUR and corresponding COD is accepted as a very useful tool to reflect the consumption of biodegradable substrates. The influence of the readily biodegradable substrate (Ss) in biological wastewater treatment systems has been extensively investigated, but little is known about...
-
The impact of slowly biodegradable organic compounds on the oxygen uptake rate in activated sludge systems
PublikacjaThe hydrolysis process of slowly biodegradable substrate (Xs) have impact on the efficiencies of nutrient removal in activated sludge systems. Measurement of OUR and corresponding COD is accepted as a very useful tool to reflect the consumption of biodegradable substrates. The influence of the readily biodegradable substrate (Ss) in biological wastewater treatment systems has been extensively investigated, but little is known about...
-
An optimal designed experiment for the alkaline hydrolysis of feather keratin
PublikacjaFeathers, burdensome waste from the poultry industry, can be a cheap source of keratin, a protein with excellent physico- chemical, biological, and mechanical properties. Acid and alkaline hydrolyses are usually adopted for isolation of keratin from its natural resources. This study aimed at assessing the statistically significant effect of input variables in the alkaline hydrolysis of keratin from chicken feathers on the process...
-
Diamine derivatives of dimerized fatty acids and bio-based polyether polyol as sustainable platforms for the synthesis of non-isocyanate polyurethanes
PublikacjaA series of environmentally friendly non-isocyanate polyurethanes (NIPUs) were successfully prepared via the polyaddition reaction of bio-based polyether polyol-based cyclic carbonate with diamine derivative of dimerized fatty acids. The syntheses of NIPUs were realized by the three-step method in the absence of toxic solvents and, importantly, the process of carbonation did not require the use of elevated pressure. The effect...
-
Phenolic compounds from Nerium oleander leaves: microwave assisted extraction, characterization, antiproliferative and cytotoxic activities
PublikacjaA microwave-assisted extraction (MAE) method was used for the extraction of phenolic compounds from Nerium oleander leaves. The influence of variables such as ethanol concentration, microwave power, irradiation time and liquid/solid ratio on polyphenol extraction was modelled using a second-order regression equation based on response surface methodology (RSM). The optimal conditions for MAE were: extraction solvent 35% ethanol...
-
Process Control of Biogas Purification Using Electronic Nose
PublikacjaNowadays, biogas produced from landfills and wastewater treatment plants or lignocellulosic biomass is important sustainable and affordable source of energy. Impurities from biogas stream can cause a serious odor problem, especially for residents of areas immediately adjacent to production plants. Therefore, biogas pre-treatment is necessary to protect engines that convert biogas into energy and in order to increase the specific...
-
Development of Gas Sensor Array for Methane Reforming Process Monitoring
PublikacjaThe article presents a new method of monitoring and assessing the course of the dry methane reforming process with the use of a gas sensor array. Nine commercially available TGS chemical gas sensors were used to construct the array (seven metal oxide sensors and two electrochemical ones). Principal Component Regression (PCR) was used as a calibration method. The developed PCR models were used to determine the quantitative parameters...
-
Green TPUs from Prepolymer Mixtures Designed by Controlling the Chemical Structure of Flexible Segments
PublikacjaThis study concerns green thermoplastic polyurethanes (TPU) obtained by controlling the chemical structure of flexible segments. Two types of bio-based polyether polyols—poly(trimethylene glycol)s—with average molecular weights ca. 1000 and 2700 Da were used (PO3G1000 and PO3G2700, respectively). TPUs were prepared via a two-step method. Hard segments consisted of 4,4?- diphenylmethane diisocyanates and the bio-based 1,4-butanodiol...
-
Numerical Analysis of Turbulent Flow over a Backward-facing Step in an Open Channel
PublikacjaComputational examinations of the flow field in an open channel having a single Backward--Facing Step (BFS) with a constant water depth of 1.5 m were performed. The effects of the expansion ratio, and the flow velocity along the reattachment length, were investigated by employing two different expansion ratios of 1.5 and 2, and eight various flow velocities of 0.5, 1, 2, 3, 4, 5, 7.5 and 10 m/sec in the Computational Fluid Dynamic...
-
Magnetic semiconductor photocatalysts for the degradation of recalcitrant chemicals from flow back water
PublikacjaIn the present study treatability of persistent organic compounds from the flow back water after hydrauling fracturing was investigated. The combination of TiO2 photocatalyst and magnetic oxide nanoparticles enhance the separation and recoverable property of nanosized TiO2 photocatalyst. Fe3O4/ TiO2 and Fe3O4@SiO2/TiO2 nanocomposites were prepared by heteroagglomeration. The photocatalysts’ characteristics by X-ray diffractometry...
-
Viability of fruit seed oil O/W emulsions in personal care products
PublikacjaThe use of fruit seed oils in personal care products is of significance to both their function and image. Poland is an important processor of fruit products within the EU, and thus has a large availability of seeds from domestic fruits, which are normally considered to be a waste material or feed for livestock. Unfortunately, current literature is scarce of the suitability of these oils for topical dermatological use in the form...
-
A fast start-up of the organotrophic anammox process inoculated with constructed wetland sediment
PublikacjaOrganotrophic anaerobic ammonium oxidation (anammox) bacteria can utilize small volatile fatty acids with nitrate as electron acceptors with less energy consumption and no biomass production. To achieve a faster and stable start-up of organotrophic anammox process, in this study, the growth of organotrophic anammox bacteria seeded from hybrid constructed wetland (CW) sediment under different TOC/TN ratios and different chloramphenicol...
-
Influence of Giant Reed (Arundo Donax L.) Culms Processing Procedure on Physicochemical, Rheological, and Thermomechanical Properties of Polyethylene Composites
PublikacjaGiant reed (Arundo donax L.) is a plant species with a high growth rate and low requirements, which makes it particularly interesting for the production of different bioproducts, including natural fibers. This work assesses the use of fibers obtained from reed culms as reinforcement for a high-density polyethylene (HDPE) matrix. Two different lignocellulosic materials were used: i) shredded culms and ii) fibers obtained by culms...
-
Investigation of Thermoplastic Polyurethanes Synthesized via Two Different Prepolymers
PublikacjaThe man aim of this work was to investigate the effect of the molecular weight of polyols, mixture of prepolymers, and [NCO]/[OH] molar ratio used during the prepolymer chain extending step on the chemical structure, thermomechanical and mechanical properties, and thermal stability of thermoplastic poly(ether-urethane)s In this work thermoplastic poly(ether-urethane)s were synthesized by using polyols with a various molecular weight,...
-
Investigation of the Combustion Processes in the Gas Turbine Module of an FPSO Operating on Associated Gas Conversion Products
PublikacjaIn this paper, we consider the issue of thermo-chemical heat recovery of waste heat from gas turbine engines for the steam conversion of associated gas for offshore vessels. Current trends in the development of offshore infrastructure are identified, and the composition of power plants for mobile offshore drilling units and FPSO vessels is analyzed. We present the results of a comparison of power-to-volume ratio, power-to-weight...
-
Identification of Optocoupler Devices with RTS Noise
PublikacjaThe results of noise measurements in low frequency range for CNY 17 type optocouplers are presented. The research were carried out on devices with different values of Current Transfer Ratio (CTR). The methods for identification of Random Telegraph Signal (RTS) in noise signal of optocouplers were proposed. It was found that the Noise Scattering Pattern method (NSP method) enables to identify RTS noise as non-Gaussian component...
-
Mechanical and structural investigations of wings of selected insect species
PublikacjaThis paper presents research and measurements leading to obtaining the Young’s modulus of wing bearing structures of selected insect species. A small testing machine intended for three-point bending and equipped with instruments registering low forces was constructed for the needs of the experiment. The machine was used to perform numerous bending tests of wings of three species of insects (obtained from a breeding farm): Attacus...
-
Sensorless Field Oriented Control of Five Phase Induction Motor with Third Harmonic Injection
PublikacjaIn this paper, a sensorless field oriented control system of five-phase induction machine with the 3rd harmonic rotor flux is presented. Two vector models, α1-β1 and α3-β3, were transformed into d1-q1, d3-q3 models oriented in rotating frames, which correspond to the 1st and 3rd harmonic plane respectively. The authors proposed the linearization of the model in d-q coordinate frames by introducing a new variable “x” which is proportional...
-
Digits Recognition with Quadrant Photodiode and Convolutional Neural Network
PublikacjaIn this paper we have investigated the capabilities of a quadrant photodiode based gesture sensor in the recognition of digits drawn in the air. The sensor consisting of 4 active elements, 4 LEDs and a pinhole was considered as input interface for both discrete and continuous gestures. Index finger and a round pointer were used as navigating mediums for the sensor. Experiments performed with 5 volunteers...
-
Short-Term Observations of Rainfall Chemistry Composition in Bellsund (SW Spitsbergen, Svalbard)
PublikacjaGlobal warming results in increasingly widespread wildfires, mostly in Siberia, but also in North America and Europe, which are responsible for the uncontrollable emission of pollutants, also to the High Arctic region. This study examines 11 samples of rainfall collected in August in a coastal area of southern Bellsund (Svalbard, Norway). It covers detailed analysis of major ions (i.e., Cl−, NO3−, and SO42−) and elements (i.e.,...
-
The reduction of auxiliaries power demand: The challenge for electromobility in public transportation
PublikacjaAn important role in the consumption of electric energy in urban transport are non-traction needs (auxiliaries), the main part of which is heating and air condition (HVAC). Auxiliaries are responsible for almost half of total energy consumption (normal weather conditions) and in the winter (or hot summer) it reaches up to 70% in daily scale. The reduction of energy used for non-traction needs is currently the main challenge related...