Filtry
wszystkich: 1649
wybranych: 1277
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: standard
-
Management Information Base module for electrical power system configuration and use
PublikacjaInternet standards describe a virtual information store, termed the Management Information Base (MIB), which is made available through Simple Network Management Protocol (SNMP). No standard MIB exists to date for monitoring power lines in facilities over IP network. This paper defines a subset of the MIB for power system monitoring.
-
Ultimate strength analysis of bulk carriers corrugated bulkheads
PublikacjaPrzedstawiono rozważania i obliczenia, których celem była ocena jakości standardu wytrzymałości grodzi falistych masowców, wprowadzonego w 1998 r. przez IACS i wdrożonego do konwencji SOLAS. Wykonane nieliniowe obliczenia MES nośności granicznej zginanych fal grodzi wykazują, że standard ten jest zbyt optymistyczny.
-
Experimental investigation into surface texture effect on journal bearings performance
PublikacjaThe aim of this study was to analyse the performance of journal bearings with specially created dimples on the sliding surface and operating under various conditions. The texture was created on the bearing surface that co-acted with the smooth journal; moreover, the variation of the textured surface of the journal mating with the smooth bearing was tested, and the results were compared to those obtained with the standard smooth...
-
Application of Impedance Spectroscopy for Bi1−xNdxFeO3 Ceramics Characterization
PublikacjaIn the present paper the synthesis conditions for fabrication of Bi1−xNdxFeO3 ceramics are reported. The single phase polycrystalline samples of Bi1−xNdxFeO3 were prepared by standard solid state reaction method from the mixture of oxides viz.: Bi2O3, Fe2O3 and Nd2O3. The samples were characterized by impedance spectroscopy in the frequency range 10Hz – 1MHz at room temperature.
-
Simulation investigation of perovskite-based solar cells
PublikacjaThree models of thin-layer lead-halide perovskite solar cells with different electron-transport layers (TiO2,SnO2,ZnO) were investigatedby the simulation method. The perovskite layer thickness was optimized for all the systems. The analysis of the standard photovoltaic cell performanceparameters at various operating temperatures was performed. The best performance was achieved for the system with theSnO2conductive layer.
-
Szacowanie estymaty menzurandu temperatury skóry człowieka podczas próby wysiłkowej
PublikacjaW artykule zaprezentowano wyniki pomiarów temperatury skóry człowieka podczas próby wysiłkowej. Ponieważ uzyskane wyniki nie podlegają rozkładowi normalnemu, wyznaczono wartości pięciu różnych estymatorów menzurandu. Otrzymane rezultaty wykazały, że w rozważanym przypadku najlepszy estymator menzurandu otrzymujemy z metody bootstrap, ponieważ charakteryzuje się on najmniejszym odchyleniem standardowym.
-
Soxhlet Extraction and New Developments Such as Soxtec in: Comprehansive Sampling and Sample Preparation
PublikacjaSoxhlet extraction is one of the most popular techniques for extraction of analytes from solid materials. Since its discovery in 1879, the standard Soxhlet technique has been routinely applied in almost every analytical laboratory. Up to this day, Soxhlet extraction technique remains a standard technique to which the performance of modern extraction techniques is compared.Over the years, an intensive research on different modifications...
-
Arterial cannula shape optimization by means of the rotational firefly algorithm
PublikacjaThe article presents global optimization results of arterial cannula shapes by means of the newly modified firefly algorithm. The search for the optimal arterial cannula shape is necessary in order to minimize losses and prepare the flow that leaves the circulatory support system of a ventricle (i.e. blood pump) before it reaches the heart. A modification of the standard firefly algorithm, the so-called rotational firefly algorithm,...
-
A Model-Order Reduction Approach for Electromagnetic Problems With Nonaffine Frequency Dependence
PublikacjaThe aim of this paper is to present a novel model-order reduction (MOR) technique for the efcient frequency-domain nite-element method (FEM) simulation of microwave components. It is based on the standard reduced-basis method, but the subsequent expansion frequency points are selected following the so-called sparsied greedy strategy. This feature makes it especially useful to perform a fast-frequency sweep of problems that lead...
-
Analysis of abrasive particle trajectories during single-sided lapping process with driven conditioning ring
PublikacjaIn this paper new kinematics systems were studied for a single lapping process. In order to ensure the constant profile wear of the tool a standard kinematic system can be changed. Lapping is carried out by applying loose abrasive grains between two surfaces and causes a relative motion between them. The result is a finish of multi-directional lay. During process, the mechanism of surface formation are decisively affected by a...
-
Heteroclinic solutions of Allen-Cahn type equations with a general elliptic operator
PublikacjaWe consider a generalization of the Allen-Cahn type equation in divergence form $-\rm{div}(\nabla G(\nabla u(x,y)))+F_u(x,y,u(x,y))=0$. This is more general than the usual Laplace operator. We prove the existence and regularity of heteroclinic solutions under standard ellipticity and $m$-growth conditions.
-
Estimation of wind pressure acting on the new palm house in Gdansk
PublikacjaThis paper deals with the problem of numerical simulations of wind loads acting on a Palm House with complex geometry. Flow simulations with aid of computational fluid dynamics procedures have been performed to check if the pressure distributions for the structure are greater than those calculated using the standard design codes with assumption that the Palm House horizontal cross sections are described by smooth cylinders.
-
Boron Difluoride Complexes of Carbamoyl Meldrum's Acids
Publikacja5-[Hydroxy(aryl/alkylamino)methylene]-2,2-dimethyl-1,3-dioxane-4,6-diones react with BF3•Et2O in mild conditions leading to the formation of boron difluoride complexes of carbamoyl Meldrum's acids. The X-ray structure has been obtained for one representative complex. The obtained new compounds are fairly stable at standard ambient conditions and easily isolable.
-
A reactive algorithm for deducing nodal forwarding behavior in a multihop ad-hoc wireless network in the presence of errors
PublikacjaA novel algorithm is presented to deduce individual nodal forwarding behavior from standard end-to-end acknowledgments. The algorithm is based on a well-established mathematical method and is robust to network related errors and nodal behavior changes. The proposed solution was verified in a network simulation, during which it achieved sound results in a challenging multihop ad-hoc network environment.
-
On Solvability of Boundary Value Problems for Elastic Micropolar Shells with Rigid Inclusions
PublikacjaIn the framework of the linear theory of micropolar shells, existence and uniqueness theorems for weak solutions of boundary value problems describing small deformations of elastic micropolar shells connected to a system of absolutely rigid bodies are proved. The definition of a weak solution is based on the principle of virial movements. A feature of this problem is non-standard boundary conditions at the interface between the...
-
Adaptive Multiplex Resource Allocation Method for DAB+ Broadcast System
PublikacjaIn this paper an adaptive multiplex resource allocation method for the DAB+ broadcast system is presented. An analysis of content transmitted over different radio programs with respect to their profile is discussed. Simulation results of an adaptive multiplexer, as well as the technological demonstrator, fully compatible with the DAB+ standard, are described. The concept is verified by a subjective quality assessment study of real-time...
-
Podejście nauczycieli akademickich do rozwoju narzędzi e-learningowych na wyższych uczelniach technicznych
PublikacjaPlatforma edukacyjna na uczelni wyższej stała się już standardem. Jest wyznacznikiem nowoczesno- ści danej uczelni. Wpływa na jej konkurencyjność. Mimo to, istnieje przekonanie że środowisko nauczycieli akademickich nie jest gotowe do akceptacji nowych środków nauczania. Postanowiono zbadać ten problem. Artykuł zawiera odpowiedź na pytanie jaki stosunek do metod e-nauczania panuje wśród nauczycieli akademickich, nie posiadających...
-
Formaty zapisu cyfrowych dokumentów muzycznych
PublikacjaW pracy zwrócono uwagę na problem przechowywania różnych postaci muzyki występujących w cyfrowych dokumentach muzycznych. Przedstawiono ogólną charakterystykę istniejących formatów zapisu danych muzycznych oraz wybrane cyfrowe formaty muzyczne. Przedstawiono również propozycję stworzenia uniwersalnego formatu opisu danych muzycznych w oparciu o istniejący standard MPEG-7.
-
Macromodels for Efficient Analysis of Open-Region Problems Using the Finite Element Method
PublikacjaThis paper presents a local model-order reduction, called macromodeling, applied to speed-up the simulations of open-region problems, analyzed by means of finite element method. This technique is illustrated by a numerical example, which deals with a dielectric resonator antenna (DRA). The obtained results show that the proposed approach is reliable and can significantly increase the standard finite element method efficiency.
-
SIMPLIFIED MODELING OF STRESS AND DEFLECTION LIMIT STATES OF UNDERGROUND TANKS
PublikacjaFuel tanks are designed with regard to standard actions and operating conditions. The work analyses the impact of corrosion and other means to variation of stresses and deformation of a horizontal underground tank shell. The computations are preliminary. Due to the long computational time of the entire tank the analysis is restricted to its part only. The full analysis is bound to assess structural reliability, further allowing...
-
Measurement system based on USB Z-Wave controller
PublikacjaA wireless measurement system based on the Z-Wave standard is presented in this paper. The system is composed of a U SB Z-Stick Gen5 controller connected to a Personal Computer and a Fibaro controller FGRGBWM-441. Operation of the system is controlled by software written in C++ using OpenZWave library. Some metrological aspects of the system are evaluated: accuracy, linearity, resolution and frequency of voltage measurements.
-
Non-Newtonian Mathematics Instead of Non-Newtonian Physics: Dark Matter and Dark Energy from a Mismatch of Arithmetics
PublikacjaNewtonian physics is based on Newtonian calculus applied to Newtonian dynamics. New paradigms such as ‘modified Newtonian dynamics’ (MOND) change the dynamics, but do not alter the calculus. However, calculus is dependent on arithmetic, that is the ways we add and multiply numbers. For example, in special relativity we add and subtract velocities by means of addition β1⊕β2=tanh(tanh−1(β1)+tanh−1(β2)), although multiplication β1⊙β2=tanh(tanh−1(β1)⋅tanh−1(β2)),...
-
Inwentaryzacja miejsc zdarzeń kryminalnych przy wykorzystaniu naziemnego skaningu laserowego
PublikacjaInwentaryzacja miejsc zdarzeń kryminalnych przy wykorzystaniu naziemnego skaningu laserowego jest rozwiązaniem często spotykanym przy w rozwiniętych krajach Europy i Ameryki Północnej. W Polsce znajdujemy pierwsze zastosowania do rejestrowania zdarzeń kryminalnych o szczególnym stopni skomplikowania lub związanych z nieprzeciętną liczbą ofiar. Zasadniczo jednak skaning laserowy stosuje się w sprawach o zabójstwo, a rzadko w rozwiązaniach...
-
Investigation of vortex assisted magnetic deep eutectic solvent based dispersive liquid–liquid microextraction for separation and determination of vanadium from water and food matrices: Multivariate analysis
PublikacjaA new and simple vortex assisted magnetic deep eutectic solvent dispersive liquid–liquid microextraction procedure (VA-MDES-DLLME) was developed for the determination of vanadium (V) in food and water samples by flame atomic absorption spectrometry (FAAS). In the extraction medium, a bis(acetylpivalylmethane) ethylenediimine (H2APM2en) was used for the complexation of V(V) in sample solution at pH 6. The VA-MDES-DLLME was optimized...
-
Radio Channel Measurements in Body-to-Body Communications in Different Scenarios
PublikacjaThis paper presents body-to-body radio channel measurements at the 2.45 GHz band, for different body motion scenarios and on-body antenna placements, and both indoor and outdoor environments. Measurement equipment, investigated scenarios and considered environments are described, an initial analysis of results being presented. The mean path loss and the standard deviation depend on the mutual location of transmitting and receiving...
-
Radio Channel Measurements in Body-to-Body Communications in Different Scenarios
PublikacjaThis paper presents body-to-body radio channel measurements at the 2.45 GHz band, for different body motion scenarios and on-body antenna placements, and both indoor and outdoor environments. Measurement equipment, investigated scenarios and considered environments are described, an initial analysis of results being presented. The mean path loss and the standard deviation depend on the mutual location of transmitting and receiving...
-
Path Loss Analysis in Off-Body Channels in Indoor Environment
PublikacjaThis temporary document describes an analysis of path loss in off-body channels in an indoor environment. The influence of body orientation and on-body antenna placement on path loss in off-body communications as well as of different bodies has been investigated. Five static scenarios, six distances between body and antenna and eight body orientations were analysed; moreover, two dynamic scenarios were investigated. The smallest...
-
New matrix-free reference material for ethene in the form of optical fibres
PublikacjaReference materials are indispensable in the qualitycontrol and quality assurance of analytical measurements. Onenovel approach to the generation of standard gaseous mixturesof toxic, reactive, volatile, labile, and malodorous substancesinvolves thermal decomposition or rearrangement, under definedtemperature conditions, of compounds immobilized, bychemical bonding, on the surface of an appropriate carrier torelease specific amounts...
-
Secure Quaternion Feistel Cipher for DICOM Images
PublikacjaAn improved and extended version of a quaternion-based lossless encryption technique for digital image and communication on medicine (DICOM) images is proposed. We highlight and address several security flaws present in the previous version of the algorithm originally proposed by Dzwonkowski et al. (2015). The newly proposed secure quater- nion Feistel cipher (S-QFC) algorithm...
-
Path-based methods on categorical structures for conceptual representation of wikipedia articles
PublikacjaMachine learning algorithms applied to text categorization mostly employ the Bag of Words (BoW) representation to describe the content of the documents. This method has been successfully used in many applications, but it is known to have several limitations. One way of improving text representation is usage of Wikipedia as the lexical knowledge base – an approach that has already shown promising results in many research studies....
-
Dokumentacja Projektowa. Wymagania dla konstrukcji stalowych. Część 2
PublikacjaOmówione zostały wymagania odnośnie wykonania rysunków warsztatowych konstrukcji stalowych stosownie do przyjętej techniki i technologii wytwarzania. W tym kontekście przestawionio wymagania do specyfikacji technicznej precyzującej standard wykonania stalowych elementów konstrukcyjnych. Poruszona została kwestia właściewej kontroli procesu projektowania konstrukcji z uwzglenieniem wymagań wprowadzanej normy europejskiej PN-EN 1990.
-
PROBABILISTIC ANALYSIS OF A SPACE TRUSS BY MEANS OF A MULTIDIMENSIONAL VARIABLE DESCRIPTION
PublikacjaThe objective of this paper is to present a variant of the point estimate method (PEM) to determine mean values and standard deviations of limit loads of engineering structures. This approach is illustrated by limit state analysis of a space truss, considering geometric and material imperfections. The calculations were performed for different random models, so the influence of random parameters on the limit load of the truss can...
-
Path Loss Measurements in Wideband Radio Link Designed for Maritime Environment
PublikacjaIn the article, the research and analysis of path loss in designed and evaluated digital radio link for high-speed data transmission in maritime environment is presented. Collected samples of received signal were used to determine the mean path loss and its standard deviation. Measuring campaign was carried out in a real maritime conditions. The mean value of path loss reached 126 dB on a distance of 11.16 km.
-
BIOGAS PRODUCTION FROM BAKERY WASTES -DYNAMICS, RETENTION TIME AND BIOGAS POTENTIAL
PublikacjaThis paper presents results of bakery-waste methane-fermentation. The scope of the study covers the determination of basic physicochemical parameters, process dynamics and retention time as well as biogas composition and biogas efficiency. Methane fermentation process was carried out in accordance with German Standard DIN 38414 S8 and under condition of 38°C. Conclusion: bakery wastes have big potential for biogas production.
-
Eye-tracking everywhere - software supporting disabled people in interaction with computers
PublikacjaIn this paper we present comprehensive system for communication with computer by gaze. One of the main assumptions behind this work was to provide solution that can be used with standard RGB webcam. The proposed comprehensive system included the eye tracking module and user interface for convenient gaze interaction with computer. As a result a fully functional application was developed. The average accuracy of the eye tracking...
-
Microcrystalline diamond film evaluation by spectroscopic optical coherence tomography
PublikacjaThis study has focused on the microcrystalline diamond film (MCD) thickness evaluation. For this purpose, optical coherence tomography (OCT) enhanced by spectroscopic analysis has been used as a method of choice. The average thickness of the tested layer was about 1.5 µm, which is below the standard 2-point OCT resolution. In this case, the usefulness of the spectroscopic analysis was confirmed for the evaluation of the thickness...
-
Influence of Actual Curing Conditions on Mechanical Properties of Concrete in Bridge Superstructures
PublikacjaThis article presents the research on the mechanical characteristics of concrete in the construction of three concrete bridges. A system of recording the internal temperature of concrete and automatic control of laboratory ovens was used for specimen curing. This allowed the specimens to be cured under conditions similar to those occurring in the structure. Before the construction, reference blocks were used to define similar curing...
-
Methods of data extraction from sub-bottom profiler's signal
PublikacjaData obtain during sounding Gdansk Bay with SES-2000 Standard parametric sub-bottom profiler has two types of information: envelope and pure signal. First is used to plot echograms in real time and contain envelope of echo. The second one is stored during sounding and can be processed after recording data. Comparison of results will be shown and discussed. First step in investigation was proper configuration of small measurement...
-
Digital Public Service Innovation: Framework Proposal
PublikacjaThis paper proposes the Digital Public Service Innovation Framework that extends the "standard" provision of digital public services according to the emerging, enhanced, transactional and connected stages underpinning the United Nations Global e-Government Survey, with seven example "innovations" in digital public service delivery -- transparent, participatory, anticipatory, personalized, co-created, context-aware and context-smart....
-
New kinematic systems in single-sided lapping and their influence on lap wear
PublikacjaPrevious studies on one-sided lapping allow to state that not only parameters of lapping elements (i.e. properties of workpiece, abrasive grains and lapping plate) impact on a lapping efficiency. Influential are also kinematics and dynamics of the process. It is crucial to control an average velocity of lapping (v), a distribution of tangential acceleration (at), a nominal pressure (p), a lapping time (t) and disposal of workpiece...
-
FEM analysis of composite materials failure in nonlinear six field shell theory
PublikacjaThe monography deals with the problem of failure initiation in thin laminated composites. Known techniques of laminate structures modelling are briefly characterised. Eventually, shell based approach is chosen for the purpose of the description of the composite structures behaviour, as it predicts their deformation and states of stress effectively in a global sense. The nonlinear six parameter shell theory (6p theory) with asymmetric...
-
Numerical Estimation of Hull Hydrodynamic Derivatives in Ship Maneuvering Prediction
PublikacjaPrediction of the maneuvering characteristics of the ship at the design stage can be done by means of model tests, computational simulations or a combination of both. The model tests can be realized as direct simulation of the standard maneuvers with the free running model, which gives the most accurate results, but is also the least affordable as it requires very large tank or natural lake, as well as complex equipment of the...
-
Assessment of unusual failure in crankshaft of heavy-duty truck engine
PublikacjaThe unusual premature failure of a heavy-duty truck engine crankshaft has been the subject of a rigorous study, and this manuscript describes it in detail. The failure was happened to begin with the growth of the crack from the surface defects, in the form of the clusters of non-metallic inclusions, in the lubrication hole zone of the first main journal, which was the stress concentration zone. A series of experiments including...
-
Estimation of Failure Initiation in Laminated Composites by means of Nonlinear Six-Field Shell Theory and FEM
PublikacjaThe monography deals with the problem of failure initiation in thin laminated composites. Known techniques of laminate structures modelling are briefly characterised. Eventually, shell based approach is chosen for the purpose of the description of the composite structures behaviour, as it predicts their deformation and states of stress effectively in a global sense. The nonlinear six parameter shell theory (6p theory) with asymmetric...
-
Macromodels for efficient FEM simulations of waveguides and resonators
PublikacjaThis paper introduces a novel technique for enhancing the efficiency of the finite element method (FEM) by incorporating special modules, called macromodels, into the standard eigenvalue formulation. The number of unknowns in the separated macromodel subdomain can be significantly reduced by orthogonal projection, using the efficient nodal order reduction algorithm. The idea of macromodels implementation is demonstrated on a simple...
-
Zastosowanie technologii internetowych w realizacji systemów zdalnego nauczania
PublikacjaW referacie dokonano przeglądu systemów zdalnego nauczania. Przedstawiono ich podstawową klasyfikację oraz prowadzone prace standaryzacyjne, w szczególności standard SCORM. Omówiono technologie internetowe stosowane w systemach e-learningu oraz ich wpływ na sposób tworzenia tych systemów oraz efektywność procesu dydaktycznego. Wskazano najbardziej prawdopodobne kierunki rozwoju systemów e-learningu wspartych technologiami internetowymi.
-
The overview of reactors used for the production of precipitated calcium carbonate via carbonation route
PublikacjaCarbonation is one of the methods for the production of precipitated calcium carbonate (PCC) on the industrial scale. A gaseous CO2 is used as a reagent in this process. The hydrodynamic conditions gener-ated in the reactor affect the course of the process and the characteristics of the precipitated calcium carbonate particles. This paper discusses the construction of standard reactors and new proposed con-struction used for the...
-
Electrochemical capacitor temperature fluctuations during charging/discharging processes
PublikacjaThepaperpresentsaproposalofusingadditionalstatisticalparameterssuchas:standarddeviation,variance, maximum and minimum increases of the observed value that were determined during measurements of temperature fields created on the surface of the tested electrochemical capacitor. The measurements were carriedoutusingthermographicmethodsinordertosupportassessmentoftheconditionofelectrochemical capacitorunderclassicdurabilitytestsbasedonmethodsofdeterminationofcapacityandequivalentseries...
-
Basic Hand Gestures Classification Based on Surface Electromyography
PublikacjaThis paper presents an innovative classification system for hand gestures using 2-channel surface electromyography analysis. The system developed uses the Support Vector Machine classifier, for which the kernel function and parameter optimisation are conducted additionally by the Cuckoo Search swarm algorithm. The system developed is compared with standard Support Vector Machine classifiers with various kernel functions. The average...
-
Identyfikacja gatunku stali zastosowanej w obiektach budowlanych
PublikacjaEksploatacja istniejących metalowych konstrukcji budowlanych często związana jest z zagadnieniem koniecznej szczegółowej identyfikacji rodzaju materiału stalowego pod kątem je go cech wytrzymałościowych i składu chemicznego. Dostępne standardowe metody laboratoryjne zazwyczaj wymagają pobrania z konstrukcji próbek materiału do badań, co nie zawsze jest możliwe. W artykule zaprezentowano alternatywne metody oceny wymienionych cech...