Filtry
wszystkich: 1155
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: MORTAR COMPRESSIVE STRENGTH
-
Influence of cyclic frozen and defrost on mechanical properties of polytetrafluoroethylene (PTFE)-coated woven fabrics
PublikacjaThis research aims to determine the influence of the cyclic process of freezing and defrosting on the mechanical properties of the chosen glass fibres and PTFE-coated woven fabrics. The specimens were subjected to freezing at about −20 °C for 4 h and thawing by full immersion into the water at about +20 °C for 4 h. The fabric samples after 25 and 50 frozen cycles were air-dried at room temperature for one week and then subjected...
-
Badania wytrzymałościowe zgrzein łączących pręty zbrojeniowe o średnicy Ø30mm
PublikacjaZakres badań dotyczy oceny wytrzymałościowej zgrzein doczołowych, wykonanych metodą zwarciową. Elementami zgrzewanymi były pręty zbrojeniowe o średnicy Ø30mm. Badania związane są z okresową kontrolą stabilności parametrów zgrzewarki, szczególnie w odniesieniu do górnych, dopuszczalnych przez producenta zakresów parametrów zgrzewania oraz analizą wyników i porównaniu rezultatów prób wytrzymałościowych uzyskanych w 2019 i 2020 w...
-
Some problems of slide bearing material fatigue evaluation.
PublikacjaA slide bearing alloy resistance against fatigue failures have been investigated for three different lubricants, different heat loadings and different stress ratio κ values. The research methods and data handling procedures for determination of particular parameter effects on fatigue strength have been described and analysed for experiments that were set and performed in laboratory tester SKMR-2. Main and interaction effects of...
-
Effect of slightly crosslinked butyl rubber and compatibilizer additives on properties of recycled polyethylene-ground tire rubber blends
PublikacjaSlightly crosslinked butyl rubber, (PhMe2CO)(2) and maleic anhydride were added as compatibilizer to the recycled polyethylene-ground tire rubber blends. Recycled postprodn. and postconsumer (shredded bottle caps) polyethylene wastes were used. The thermoplastic compns. were studied for statistic and dynamic mech. properties and morphol. The addn. of butyl rubber resulted in a decrease of the tensile strength and hardness of the...
-
Processing of point cloud data retrieved from terrestrial laser scanning for structural modeling by Finite Element Method
PublikacjaFinite Element Method is one most popular contemporary method of strength analysis. The method is an advanced method for solving differential equations, based on discretization, which means that area is divided into finite elements. Each finite element has a solution of the equation approximated by specific functions and performing the actual calculations only for nodes of this division. Finite Element Method is widely used in...
-
Optimization of biocorrosion resistance and mechanical properties of PM Ti–XAl–2Fe–3Cu alloys by response surface methodology
PublikacjaIn the current study, the biocorrosion resistance and mechanical properties of the Ti–XAl–2Fe–3Cu (wt%) (X = 6, 4, 2 wt%) alloy produced by powder compact extrusion of blended elemental powders were optimized by using the response surface methodology in order to gain the best combination of processing parameters. To run the optimization process, central composite design with three equal levels of oxygen, hydrogen and aluminum was...
-
Eksperymentalna weryfikacja procedury szacowania wytrzymałości młodego betonu wg normy ASTM C1074
PublikacjaW referacie przedstawiono metodę służącą oszacowaniu wytrzymałości betonu w trakcie procesu dojrzewania (ang. Maturity Method) bazującą na procedurze określonej zgodnie z amerykańską normą, która uwzględnia wpływ połączonych efektów temperatury i czasu na rozwój wytrzymałości betonu. Standardy ASTM C1074 zostały opracowane przez NBS (ang. National Bureau of Standards) z uwagi na powtarzające się wypadki na palcu budowy wynikające...
-
The Influence of Articular Cartilage Thickness Reduction on Meniscus Biomechanics
PublikacjaObjective Evaluation of the biomechanical interaction between meniscus and cartilage in medial compartment knee osteoarthritis. Methods The finite element method was used to simulate knee joint contact mechanics. Three knee models were created on the basis of knee geometry from the Open Knee project. We reduced the thickness of medial cartilages in the intact knee model by approximately 50% to obtain a medial knee osteoarthritis...
-
Parametry mechaniczne platformy roboczej na podstawie badań DMT
PublikacjaNośność platformy roboczej określana jest w sposób analogiczny do nośności podłoża uwarstwionego, w którym warstwa wierzchnia zbudowana z gruntu niespoistego spoczywa na słabonośnym podłożu z gruntu spoistego. Badanie DMT wykorzystano do wyznaczenia parametrów wytrzymałościowych podłoża (kąta tarcia wewnętrznego warstwy górnej i wytrzymałości na ścinanie bez odpływu podłoża słabonośnego) oraz do wyznaczenia modułu odkształcenia...
-
Buckling analyses of cylindrical metal silos containing bulk solids
PublikacjaThe paper presents quasi-static 3D buckling analysis results of thin-walled cylindrical metal silos with and without bulk solids. The behaviour of the bulk solid was described with a hypoplastic constitutive model. Non-linear analyses with geometric and material non-linearity were performed with a perfect and an imperfect silo shell. Different initial geometric imperfections were considered. The influence of internally stored bulk...
-
SUBSOIL CHARACTERISTICS OF THE VISTULA RIVER DIKES
PublikacjaThe results of CPTU tests are used to determine the strength parameters of a dike subsoil. Stress state and stress history of the subsoil under the flood embankment was evaluated with CPTU and DMT tests. Normally consolidated soil was found under the central part of the dike, while the subsoil near the dike toe is found to be overconsolidated. Due to consolidation the undrained shear strength of the subsoil under the central part...
-
Wyznaczanie wytrzymałości betonu na podstawie funkcji dojrzałości wg amerykańskiej normy ASTM C1074-11
PublikacjaArtykuł poświęcono wyznaczaniu wytrzymałości betonu na podstawie funkcji dojrzałości wg normy ASTM C1074-11 (ang. Maturity Method). Metoda bazuje na rejestracji zmian tem - peratury w trakcie hydratacji dojrzewającego betonu. Wartykule zaprezentowano procedurę badawczą służącą wyznaczeniu funk - cji dojrzałości dla wybranej mieszanki betonowej oraz zależności wytrzymałość-dojrzałość. Celem badań jest wyznaczanie zmian w czasie...
-
Bearing capacity of the working platform with kinematic method
PublikacjaBearing capacity of the working platform for heavy tracks was analysed using Distinct Layout Optimization (DLO) method. The platform layer constructed from cohesionless soils is resting on weak cohesive subgrade. Different thickness of the platform, its effective angle of internal friction and undrained shear strength of the soft soil were taken into consideration. Kinematic method permits different failure mechanisms to be analyzed....
-
Meso‐scale analyses of size effect in brittle materials using DEM
PublikacjaThe paper describes numerical meso-scale results of a size effect on strength, brittleness and fracture in brittle materials like concrete. The discrete element method (DEM) was used to simulate the size effect during quasi-static splitting tension with the experimental-based meso-structure. The two-dimensional (2D) calculations were carried out on concrete cylindrical specimens with two diameters wherein two different failure...
-
Pressure-induced flow processing behind the superior mechanical properties and heat-resistance performance of poly(butylene succinate)
PublikacjaWe propose a pressure-induced flow (PIF) processing method for the simultaneous enhancement of strength, toughness, and heat resistance of biodegradable poly(butylene succinate) (PBS). The pressure and temperature were systematically adjusted to optimize the tensile strength of PBS. Under the optimized processing conditions, the structured PBS was characterized by relatively high strength of 89.5 MPa, toughness of 21.4 kJ·m−2 ,...
-
Styrene-Butadiene Rubber/Modified Ground Tire Rubber Blends Co-Vulcanization: Effect of Accelerator Type
PublikacjaGround tire rubber was thermo-mechanically modified with using a co-rotating twin screw extruder. Modification of GTR was conducted in autothermal conditions. Styrene-butadiene rubber and modified ground tire rubber blends were prepared via two-roll milling. Obtained compounds were cured with conventional system (sulfur/vulcanization accelerator ratio was 2:1). During this research three commonly vulcanization accelerators (MBT,...
-
Temper bead welding of S420G2+M steel in water environment
PublikacjaThe article presents the idea of the use of Temper Bead Welding (TBW) technique to improve the weldability of high strength steel at underwater wet welding conditions. Wet welding method with the use of covered electrodes is described. This work shows results of metallographic examinations and hardness measurements of samples of S420G2+M steel with weld beads performed under water. It has been shown that Temper Bead Welding technique...
-
Selected Problems of Machine Dynamics II
Kursy OnlineThe following set of lectures is performed: 1. LECTURE No.1 - INTRODUCTION TO SELECTED PROBLEMS OF MACHINE DYNAMICS. STRUCTURES and MACHINES 2. LECTURE No.2 - ENVIRONMENT, LOADS ON STRUCTURES and MACHINES 3. LECTURE No.3 - DYNAMICS of STRUCTURES and MACHINES 4. LECTURE No.4 - STRENGTH of STRUCTURES and MACHINES 5. LECTURE No.5 - SPECIAL PROBLEMS ASSOCIATED with DYNAMICS and STRENGTH of STRUCTURES and MACHINES
-
Selected Problems of Machine Dynamics
Kursy OnlineThe following set of lectures is performed: 1. LECTURE No.1 - INTRODUCTION TO SELECTED PROBLEMS OF MACHINE DYNAMICS. STRUCTURES and MACHINES 2. LECTURE No.2 - ENVIRONMENT, LOADS ON STRUCTURES and MACHINES 3. LECTURE No.3 - DYNAMICS of STRUCTURES and MACHINES 4. LECTURE No.4 - STRENGTH of STRUCTURES and MACHINES 5. LECTURE No.5 - SPECIAL PROBLEMS ASSOCIATED with DYNAMICS and STRENGTH of STRUCTURES and MACHINES
-
Selected Problems of Machine Dynamics - advances
Kursy OnlineThe following set of lectures is performed: 1. LECTURE No.1 - INTRODUCTION TO SELECTED PROBLEMS OF MACHINE DYNAMICS. STRUCTURES and MACHINES 2. LECTURE No.2 - ENVIRONMENT, LOADS ON STRUCTURES and MACHINES 3. LECTURE No.3 - DYNAMICS of STRUCTURES and MACHINES 4. LECTURE No.4 - STRENGTH of STRUCTURES and MACHINES 5. LECTURE No.5 - SPECIAL PROBLEMS ASSOCIATED with DYNAMICS and STRENGTH of STRUCTURES and MACHINES
-
Selected Problems of Machine Dynamics - advances
Kursy OnlineThe following set of lectures is performed: 1. LECTURE No.1 - INTRODUCTION TO SELECTED PROBLEMS OF MACHINE DYNAMICS. STRUCTURES and MACHINES 2. LECTURE No.2 - ENVIRONMENT, LOADS ON STRUCTURES and MACHINES 3. LECTURE No.3 - DYNAMICS of STRUCTURES and MACHINES 4. LECTURE No.4 - STRENGTH of STRUCTURES and MACHINES 5. LECTURE No.5 - SPECIAL PROBLEMS ASSOCIATED with DYNAMICS and STRENGTH of STRUCTURES and MACHINES
-
Strenght of materials towards applications, PG_00053661
Kursy OnlineThe aim of the course is to perform the following subjects: 1. LECTURE No.1 - INTRODUCTION TO SELECTED PROBLEMS OF MACHINE DYNAMICS. STRUCTURES and MACHINES 2. LECTURE No.2 - ENVIRONMENT, LOADS ON STRUCTURES and MACHINES 3. LECTURE No.3 - DYNAMICS of STRUCTURES and MACHINES 4. LECTURE No.4 - STRENGTH of STRUCTURES and MACHINES 5. LECTURE No.5 - SPECIAL PROBLEMS ASSOCIATED with DYNAMICS and STRENGTH of STRUCTURES and MACHINES
-
Efektywność skrępowania betonu w grubościennych słupach typu Concrete-Filled Steel Tube o przekroju kołowym
PublikacjaW słupach typu CFST w stanie granicznym dochodzi do zwiększenia wytrzymałości betonu rdzenia na skutek jego skrępowania. Zaistnienie tego zjawiska zależy od wielu czynników. Jednym z najważniejszych z nich jest sztywność obwodowa płaszcza stalowego. Jej wpływ na efektywność wzrostu wytrzymałości betonu rdzenia przebadano eksperymentalnie na grupie 48 grubościennych słupów CFST. Wykazano, że nadmierne zwiększanie grubości płaszcza...
-
Unprecedented Adhesive Performance of Propylene-Based Hydroxyl Functionalized Terpolymers
PublikacjaThe synthesis of hydroxyl functionalized propylene-based terpolymers and their performance as hot melt adhesives were investigated. The products comprise uniformly distributed butyl and 4-hydroxyl-butyl branches along the polypropylene backbone. Despite the low hydroxyl-functionality level of ≤ 0.5 mol%, hydroxyl functionalized terpolymers show formidable adhesion to aluminum and steel providing an adhesive strength exceeding 16...
-
A benchmark for particle shape dependence
PublikacjaParticle shape is a major parameter for the space-filling and strength properties of granular materials. For a systematic investigation of shape effect, a numerical benchmark test was set up within a collaborative group using different numerical methods and particles of various shape characteristics such as elongation, angularity and nonconvexity. Extensive 2D shear simulations were performed in this framework and the shear strength...
-
Particle shape dependence in 2D granular media
PublikacjaParticle shape is a key to the space-filling and strength properties of granular matter. We consider a shape parameter eta describing the degree of distortion from a perfectly spherical shape. Encompassing most specific shape characteristics such as elongation, angularity and non-convexity, eta is a low-order but generic parameter that we used in a numerical benchmark test for a systematic investigation of shape dependence in sheared...
-
Microstructure, mechanical properties, and flame retardancy of nanoclay-incorporated polyurethane flexible foam composites
PublikacjaThe present work seeks to investigate microstructure, mechanical properties, and flame retardancy of polyurethane/nanoclay flexible foam composites. In this regard, we prepared various nanocomposites with and without nanoclay and observed the resulting morphologies to correlate them with the other corresponding characteristics. The results provided support for the fact that tensile strength and compression set will increase with...
-
FE analysis of a coupled energetic-statistical size effect in plain concrete beams with varying material properties.
PublikacjaThe numerical FE investigations of a coupled energetic-statistical size effect in unnotched concrete beams of similar geometry under quasi-static three point bending were performed within elasto-plasticity with non-local softening. The stochastic FE analyses were carried out with three different beam sizes. Deterministic calculations were performed with the uniform distribution of a uniaxial tensile strength. In statistical calculations...
-
Negative Poisson’s ratio from pentagons: A new auxetic structure combining three different auxetic mechanisms
PublikacjaA novel class of two-dimensional auxetic structures based on the pentagon motif is proposed. Their mechanical properties are investigated by combining molecular mechanics simulations with a simple three-parameter mechanical model which assumes perfectly elastic behavior. It is predicted that the proposed structures – termed as double re-entrant honeycomb – may possess unique mechanical characteristics, which include complete and...
-
The XRD diffraction patterns of (La0.3Sr0.6Ce0.1)0.9FexTi(1-x)O3-δ (x=0.1, 0.2 and 0.3) materials after reduction at 900 deg.C in hydrogen
Dane BadawczeThe (La0.3Sr0.6Ce0.1)0.9FexTi(1-x)O3-δ (x=0.1, 0.2 and 0.3) materials were synthesized via the Pechini method. First, the reagents in the form of nitrates were weighed and dissolved in DI water. In another beaker, a stoichiometric amount of titanium (IV) butoxide (Ti(OBu)4) was mixed together with reagent-grade ethylene glycol (EG), and citric acid...
-
Linear and nonlinear impedance of iron containing silicate glasses
Dane BadawczeThe linear and nonlinear impedance ofglasses doped with iron oxide were measured. Glass samples (50 SiO2-50-xPbO-xFe2O3 in mol%) were prepared by the conventional melt quenching technique. The substrates were powdered in a mortar and melted in Al2O3 crucibles. The melting was conducted in air at 1623K. The melts were poured out on plate heated up to...
-
Topography of barium-vanadate glasses
Dane BadawczeThe topography of barium-vanadate glasses was measured. Samples of the composition of xBaO-(100-x)V2O5 where x= 30, 40 and 45 (in %mol) were prepared by the conventional melt quenching technique. Appropriate amounts of reagents: BaO (≥99.9%, P.P.H STANLAB Sp.J.) and V2O5 (≥99.9%, POCH) were thoroughly mixed in an agate mortar. The melting was performed...
-
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublikacjaIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...
-
Mechanical characteristics of welded joints between different stainless steels grades
Publikacjanvestigation of mechanical characteristics of welded joints is one of the most important tasks that allow determining their functional properties. Due to the very high, still rising, cost of some stainless steels it is justified, on economic grounds, welding austenitic stainless steel with steels that are corrosion-resistant like duplex ones. According to forecasts the price of...
-
Termooksydacyjna i fotooksydacyjna degradacja pianek poliuretanowych
PublikacjaPrzeprowadzono ocenę efektywności działania wybranych środków przeciwstarzeniowych w sztywnych piankach poliuretanowych, otrzymywanych na drodze syntezy jednoetapowej. Ocenę tę oparto na pomia-rach zmian barwy oraz wytrzymałości mechanicznej zsyntezowanych materiałów. Na podstawie analizy uzyskanych wyników stwierdzono, iż dodatek 3% mieszaniny I rzędowego antyutleniacza fenolowego oraz benzotriazolowego absorbera UV znacząco zmniejsza...
-
On the Buckling Response of Axially Pressurized Nanotubes Based on a Novel Nonlocal Beam Theory
PublikacjaIn the present study, the buckling analysis of single-walled carbon nanotubes (SWCNT) on the basis of a new refined beam theory is analyzed. The SWCNT is modeled as an elastic beam subjected to unidirectional compressive loads. To achieve this aim, the new proposed beam theory has only one unknown variable which leads to one equation similar to Euler beam theory and is also free from any shear correction factors. The equilibrium...
-
Roller burnishing
PublikacjaThe paper shows the process of roller burnishing as a method of finishing machine components. Based on own research the author presents the effects of the roller burnishing process to increase the hardness and residual stress as well as the wear and fatigue strength of burnishing components.
-
Numerical analysis of lumbar spine injury during road safety barrier collision
PublikacjaPurpose: Enhancing road safety is a critical goal worldwide, necessitating the development of clear standards for road safety systems. This study focuses on lumbar spine (L-spine) compression injuries during collisions with concrete road safety barriers (RSBs). It aims to analyze internal forces during impact to understand L-spine injury biomechanics in such accidents. Methods: The research included a literature review, analyzing...
-
The Possibilities of Improving the Fatigue Durabilityof the Ship Propeller Shaft by Burnishing Process
PublikacjaHeavily loaded structural elements operating in a corrosive environment are usuallyquickly destroyed. An example of such an element is a ship propeller operating in a seawaterenvironment. This research presents a fatigue resistance test performed on elements operating inseawater. Different processing parameters applied on the samples in particular were compared withthe specimens whose surface had been burnished differently and...
-
The effect of numerical 2D and 3D FEM element modelling on strain and stress distributions at laser weld notches in steel sandwich type panels
PublikacjaLike other means of transport, merchant ships face the problem of increasing requirements concerning the environment protection, which, among other issues, implies the reduction of fuel consumption by the ship. Here, the conventional approach which consists in making use of higher strength steels to decrease the mass of the ship hull can be complemented by the use of new steel structures of sandwich panel type. However, the lack...
-
Challenges and opportunities related to the use of sewage sludge ash in cement-based building materials – A review
PublikacjaDue to the increasingly demanding legal regulations, regarding both sewage sludge (SS) and solid residues obtained during its thermal utilization processes, new solutions to limit their negative impact on the environment are sought. One approach that eliminates the risk of sewage sludge ash (SSA) is its use in cement building materials. The article contains a detailed literature review regarding the use of SSA in mortars and concretes,...
-
Influence of Water-Induced Degradation of Polytetrafluoroethylene (PTFE)-Coated Woven Fabrics Mechanical Properties
PublikacjaThe impact of water-induced degradation on the mechanical properties of the chosen two PTFE-coated, glass threads woven fabrics is investigated in this paper. The paper begins with a survey of literature concerning the investigation and determination of coated woven fabric properties. The authors carried out the uniaxial tensile tests with an application of flat and curved grips to establish the proper values of the ultimate tensile...
-
Fluid–solid interaction on a thin platelet with high-velocity flow: vibration modelling and experiment
PublikacjaThe paper concerns the nonlinear behaviour of a thin platelet that is streamlined in an aerodynamic tunnel. The air velocity in the aerodynamic tunnel was at 858.9 km/h or 0.7 Ma (Ma—Mach number is a dimensionless quantity in fluid dynamics representing the ratio of flow velocity past a boundary to the local speed of sound). This experiment was numerically simulated using FSI (fluid–solid interaction) tools, namely the coupling...
-
Thermal and mechanical properties of polyurethanes modified with L-ascorbic acid
PublikacjaIn this study we report the thermal and mechanical properties of polyurethanes modified with ascorbic acid (AA). Ascorbic acid was used as a modifier at concentration of 1 or 2 mass%. The antioxidative properties of AA may improve the biocompatibility of the obtained materials, which were designed for biomedical applications. In this paper we describe characterization of obtained unmodified and ascorbic acid modified polyurethanes...
-
Analytical Buckling of FG Nanobeams on The Basis of A New One Variable First-Order Shear Deformation Beam Theory
PublikacjaIn this work, buckling analysis of functionally graded (FG) nanobeams based on a new refined beam theory has been analyzed. The beam is modeled as an elastic beam subjected to unidirectional compressive loads. To achieve this aim, the new obtained beam theory has only one variable which leads to one equation similar to the Euler beam theory and also is free of any shear correction factor. The equilibrium equation has been...
-
Experimental and numerical evaluation of mechanical behaviour of composite structural insulated panels
PublikacjaComposite structural insulated panels (CSIPs) are novel prefabricated elements for structural applications. Panels under consideration are made from glass-fibre reinforced magnesia cement boards as facesheets and expanded polystyrene foam (EPS) as a core. Quasi-static full-scale and model bending tests under monotonic loading were performed to recognize mechanical properties of CSIPs in flexure. In addition, tensile, compressive,...
-
Corrigendum to “Fatigue life improvement using low transformation temperature weld material with measurement of residual stress” [Int. J. Fatigue 164 (2022) 107137]
PublikacjaWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
Fatigue life improvement using low transformation temperature weld material with measurement of residual stress
PublikacjaWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
Numerical simulation of laminate composite specimens failure
PublikacjaThis work presents some numerical results concerning simulation of failure of laminate composite specimens. In the article two tests to determine ultimate strength in an orthotropic layer, are considered: tension (TT1) and compression (TC1) test. The outcome is compared with experimental data provided by [9,10].
-
Laser Welding of UNS S33207 Hyper-Duplex Stainless Steel to 6061 Aluminum Alloy Using High Entropy Alloy as a Filler Material
PublikacjaThe high entropy alloy (HEA) filler used during the fabrication method determines the reliability of HEAs for steel-aluminum dissimilar alloy configuration. HEAs have a direct impact on the formation of intermetallic compounds (IMC) formed by the interaction of iron (Fe) and aluminum (Al), and influence the size of the joint’s interaction zone. A novel welding process for Fe-Al alloy joints was developed to prevent the development...