Wyszukiwarka
Wyniki wyszukiwania dla: degradation kinetics
-
Removal efficiency of phenol by ozonation process with calcium peroxide from aqueous solutions
PublikacjaPhenol has been introduced as a priority pollutant by the US Environmental Protection Agency. Advanced oxidation processes (AOPs) are one of the most efcient methods for removal of non-degradable organic pollutants in aqueous solutions. The removal efciencies of phenol and COD under optimal conditions pH=3, phenol concentration=5 mg/L, CaO2 concentration=0.025 mg/L, temperature 25 °C, 1 g/min ozonation rate and contact time=90...
-
Fabrication, Microstructure and High Temperature Corrosion Resistance of Porous Alloys for Solid Oxide Fuel Cells
PublikacjaPorous alloys find use in modern Solid Oxide Fuel Cells as the supporting structures. As they are exposed to high temperatures (> 500°C) an oxide scale forms on their surface due to high temperature corrosion phenomena. Since the ratio between the surface area and volume is much higher than for planar samples, formation of the oxide can lead to a breakaway oxidation after relatively short times. Therefore corrosion properties of...
-
Laser reflectance interferometry system with a 405 nm laser diode for in-situ measurement of CVD diamond thickness
PublikacjaIn situ monitoring of the thickness of thin diamond films during technological processes is important because it allows better control of deposition time and deeper understanding of deposition kinetics. One of the widely used techniques is laser reflectance interferometry (LRI) which enables non-contact measurement during CVD deposition. The authors have built a novel LRI system with a 405 nm laser diode which achieves better...
-
ANALYSIS OF UNCONTROLLED WEAR IN THE AREA OFA BELLEVILLE SPRING OF A FRICTION TORSIONAL VIBRATIONDAMPER IN A MOTOR VEHICLE CLUTCH
PublikacjaThe article describes the problem of excessive tribological wear of a torsional vibration damper built into a single-disc friction clutch of a truck vehicle. In contrast to the controlled, design-based wear of damper’s friction rings, i.e., wear whose kinetics are known and predictable, uncontrolled wear at Belleville spring contact surfaces effects in a premature decrease in the damper’s friction torque and, consequently, loss...
-
Hydrogen direct reduction and reoxidation behaviour of high-grade pellets
PublikacjaHigh grade pellets with basicity index close to 0.5 were directly reduced in pure hydrogen atmosphere. The reduction experiments were performed in the temperature range 800 e1000 C at the pressure of 8 bar. The pellets internal structure was analysed through micro tomography observations in the unreduced and reduced conditions. After reduction, the pellets showed a variation of porosity up to more than 15% with a remarkable change...
-
Cure kinetics of epoxy/MWCNTs nanocomposites: Isothermal calorimetric and rheological analyses
PublikacjaA combinatorial route has been applied in cure kinetics study of epoxy nanocomposites containing multi-walled carbon nanotubes (MWCNTs) based on differential scanning calorimetry and rheokinetic analyses under isothermal conditions. Pristine and amine-modified MWCNTs bearing primary and secondary amines were used at very low concentrations (0.1 and 0.3 wt.% based on epoxy weight). Model-free and model-fitting methods were applied...
-
Influence of Gd deposition on the oxidation behavior and electrical properties of a layered system consisting of Crofer 22 APU and MnCo2O4 spinel
PublikacjaIn the study, the surface of the Crofer 22APU ferritic steel was modified with gadolinium oxide nanoparticles and a protective-conducting layer consisting of the MnCo2O4 spinel. This system was studied in the context of application in IT-SOFC interconnects. Four types of samples were studied: unmodified steel, steel coated with a manganese-cobalt spinel layer, steel modified with gadolinium oxide nanoparticles, and a system consisting...
-
Removal of nonsteroidal anti-inflammatory drugs and analgesics from wastewater by adsorption on cross-linked β-cyclodextrin
PublikacjaWe present a method using the material in the form of cross-linked β-cyclodextrin (CD) showing high efficiency in the simultaneous removal of hazardous pollutants from sewage, such as diclofenac (DIC), ibuprofen (IBU), ketoprofen (KETO), naproxen (NAPR), salicylic acid (SALI) and tramadol (TRAM). The material is stable and particularly easy to regenerate. The sorbent probably remembers the shape of the contaminants, which increases...
-
Photophysics of Ru(II) Dyads Derived from Pyrenyl-Substitued Imidazo[4,5-f][1,10]phenanthroline Ligands.
PublikacjaThe photophysics of a series of Ru(II) dyads based on the 2-(1-pyrenyl)-1H-imidazo[4,5-f][1,10]-phenanthroline ligand was investigated. The ability of these metal complexes to intercalate DNA and induce cell death upon photoactivation makes them attractive photosensitizers for a range of photobiological applications, including photodynamic therapy. In the present study, time-resolved transient absorption and emission spectroscopy...
-
Optically transparent boron-doped nanocrystalline diamond films for spectroelectrochemical measurements on different substrates
PublikacjaFabrication process of optically transparent boron nanocrystalline diamond (BNCD) electrode on silicon and quartz substrate was shown. The B-NCD films were deposited on the substrates using Microwave Plasma Assisted Chemical Vapor Deposition (MWPACVD) at glass substrate temperature of 475 ºC. A homogenous, continuous and polycrystalline surface morphology with high sp3 content in B-NCD films and film thickness depending from substrate...
-
Assessment of High-Temperature Oxidation Properties of 316L Stainless Steel Powder and Sintered Porous Supports for Potential Solid Oxide Cells Applications
PublikacjaIn this work, oxidation properties of austenitic 316L stainless steel powder and sintered porous support were investigated at the temperature range of ~600-750 °C for 100 hours in ambient air. Oxidation kinetics was determined by continuous thermogravimetry and analyzed employing parabolic rate law. It was observed that oxidation leads to the formation of an oxide scale, with substantial oxidation occurring at ≥ 650 °C in the powder....
-
Multisine impedimetric monitoring with an in-depth distribution of relaxation times analysis of WE43 and AZ31 magnesium alloys corrosion
PublikacjaThis research aims to develop and utilize an impedance-based tool for monitoring non-stationary electrochemical processes, coupling the multisinusoidal perturbation signal approach and distribution of relaxation times (DRT) analysis for the first time. The approach was used to distinguish independent processes occurring at the surface of AZ31 and WE43 Mg alloys undergoing corrosion in Hank’s Balanced Salt Solution at 37 °C. We...
-
Direct reduction of pellets through hydrogen: Experimental and model behaviour
PublikacjaThis paper presents the hydrogen reduction behaviour of industrial pellets designed for the efficient hydrogen based direct reduction. The pellets were provided with very low non ferrous oxides percentage (0.52 of basicity index) and with the absence on TiO2 oxides. The pellets measured diameters in the range 1.14–1.72 cm and were characterized in terms of porosity, pores size, tortuosity and compression strength. The pellets were...
-
Effect of TiO2 Concentration on Microstructure and Properties of Composite Cu–Sn–TiO2 Coatings Obtained by Electrodeposition
PublikacjaIn this work, Cu–Sn–TiO2 composite coatings were electrochemically obtained from a sulfate bath containing 0–10 g/L of TiO2 nanoparticles. The effect of TiO2 particles on kinetics of cathodic electrodeposition has been studied by linear sweep voltammetry and chronopotentiometry. As compared to the Cu–Sn alloy, the Cu–Sn–TiO2 composite coatings show rougher surfaces with TiO2 agglomerates embedded in the metal matrix. The highest...
-
Proton-Electron Hole Interactions in Sr(Ti,Fe)O3−δ Mixed-Conducting Perovskites
PublikacjaOxides in which total electrical conductivity is determined by the partial conductivities of three types of charge carriers i.e. holes/ electrons, oxygen ions, and protons are key components of well-functioning proton ceramic fuel cells. Apart from electrochemical properties also easily modified microstructure is an important feature of the electrodes. In the paper, a group of SrTi1−xFexO3−δ (STF, x = 0.2–0.8) perovskites prepared...
-
Transport of paracetamol in swellable and relaxing polyurethane nanocomposite hydrogels
PublikacjaPolyurethane hydrogels are potentially attractive materials for biomedical applications. They are able to absorb large amount of water, biological fluids or active substances, and thus, they have potential to be used as absorbents or wound-healing dressings. They are also used for the controlled release of therapeutics because of their capacity to embed biologically active agents in their water-swollen network. The presence of...
-
Monitoring of crosslinking of a DGEBA-PAMAM adhesive in composite/aluminium bonded joint using mechanical and ultra-sound techniques
PublikacjaAdhesive cure is an important and determining aspect of strength and stability of bonded structures. Crosslinking of the polymer leads to the adhesive strength, stiffness and durability. Depending on the resin and curing agent used, cure time can vary from minutes to weeks, even then 100% crosslinking not being guaranteed. Standard methods based on dynamic mechanical analysis (DMA) or calorimetric techniques (DSC, DTA) are valuable...
-
Enhanced electrochemical performance of SnS-PPy-carbon black composite with a locust bean gum as a binder as in anode in lithium-ion batteries
PublikacjaWater-soluble binders—locust bean gum (LBG) and carboxymethyl cellulose (CMC) were tested with the SnS anode modified by new conducting material polypyrrole—carbon black composite (PPyCB) and compared with the environmentally unfriendly widely used polyvinylidene fluoride (PVdF) as an organic binder. The electrochemical properties of tested electrodes were investigated by galvanostatic charging/discharging tests, cyclic voltammetry,...
-
Cu-Doped Layered Double Hydroxide Constructs the Performance-Enhanced Supercapacitor Via Band Gap Reduction and Defect Triggering
PublikacjaLayered double hydroxides (LDHs) are regarded as the excellent electrode materials for supercapacitors because of their high theoretical capacitance and abundance. However, the poor conductivity and limited reaction kinetics of LDHs restrict their practical application severely. Herein, Cu is chosen from groups VIII/IB/IIB as dopants for Co-based LDH (CuCo-LDH). The designed metal–organic framework-derived hierarchical CuCo-LDH...
-
A mobile loop order–disorder transition modulates the speed of chaperonin cycling
PublikacjaMolecular machines order and disorder polypeptides as they form and dissolve large intermolecular interfaces, but the biological significance of coupled ordering and binding has been established in few, if any, macromolecular systems. The ordering and binding of GroES co-chaperonin mobile loops accompany an ATP-dependent conformational change in the GroEL chaperonin that promotes client protein folding. Following ATP hydrolysis,...
-
High catalytic performance of laccase wired to naphthylated multiwall carbon nanotubes
PublikacjaThe direct electrical connection of laccase on the electrode surface is a key feature in the design of efficient and stable biocathodes. However, laccases can perform a direct electron transfer only when they are in the preferable orientation toward the electrode. Here we report the investigation of the orientation of Laccase from Amano on multi-walled carbon nanotube surface modified with naphthalene group. Naphthylated multi...
-
Electrochemical performance of thin free-standing boron-doped diamond nanosheet electrodes
PublikacjaIn the following work we describe preparation and the electrochemical performance of thin and free-standing heavy boron-doped diamond (BDD) nanosheets. The investigated foils were deposited on Ta substrate using microwave plasma-enhanced chemical vapor deposition technique (MPECVD). Foils of two B-dopant densities were investigated, obtained on the base of 10 k and 20 k ppm [B]/[C] ratio in the gas admixture. The obtained foils...
-
Advances in analysis, quantification and modelling of N2O emission in SBRs under various DO set points
PublikacjaNitrous oxide (N2O), considered a major greenhouse gas (GHG) in wastewater treatment plants (WWTPs), is produced during both nitrification and denitrification processes; hence, it needs to be controlled by internal and external strategies. Various factors, such as DO, temperature, and pH, could be incorporated into the mitigation of emissions in WWTPs. In this research, potential operational strategies were investigated in order...
-
Mathematical modelling of two-step nitrification-denitrification for treatment of sludge digester liquors: influence of nitrite (NO2-N) on the process kinetics
PublikacjaSeparate treatment of the sludge digester liquors is an alternative for expansion of the mainstream treatment line. In order to reduce the oxygen demand for nitrification and organic carbon demand for denitrification, a shortcut in the nitrogen conversion pathway has been promoted in recent years, i.e. nitrification-denitrification via NO2-N instead of NO3-N. Although NO2-N is a common intermediate product of nitrification and...
-
Kinetics of pollutants removal in hybrid treatment wetlands – Case study comparison
PublikacjaRecent years have seen an increasing interest in hybrid constructed wetland (HCW) systems for domestic sewage treatment. This paper is focused on kinetics of removal of the main pollutants occurring in wastewater i.e. organics expressed as chemical oxygen demand, biochemical oxygen demand and total nitrogen. The purpose of the article is to compare different HCW configurations in terms of mass removal rates (MRR) and removal rate...
-
The significance of the properties of water for the working cycle of the kinesin molecular motor
PublikacjaExplicit solvent molecular dynamics simulations were performed in this study to investigate and discuss several aspects of the influence of the properties of water on the working cycle of a molecular motor from the kinesin superfamily. The main objects of attention were: the binding of the neck linker and the association of the kinesin and the tubulin. The docking of the neck linker is considered a crucial event during the working...
-
Molybdenum sulfide modified with nickel or platinum nanoparticles as an effective catalyst for hydrogen evolution reaction
PublikacjaIn this study, we investigate the catalytic performance of molybdenum sulfide (MoS2) modified with either nickel (Ni) or platinum (Pt) nanoparticles as catalysts for the hydrogen evolution reaction (HER). The MoS2 was prepared on the TiO2 nanotube substrates via a facile hydrothermal method, followed by the deposition by magnetron sputtering of Ni or Pt nanoparticles on the MoS2 surface. Structural and morphological characterization...
-
Hardware-Software Implementation of Basic Principles Simulator of Nuclear Reactor Processes
PublikacjaThe paper presents implementation process of basic principle simulators of a nuclear reactor processes. Simulators are based on point-models of processes: kinetics of neutrons, heat generation and exchange, poisoning and burning-up nuclear fuel. Reference simulator was developed in MATLAB/Simulink without taking into account real-time operation. Second simulator was built using the toolbox xPC with hard real-time requirements....
-
Topical delivery of pharmaceutical and cosmetic macromolecules using microemulsion systems
PublikacjaMicroemulsions are transparent, thermodynamically stable colloidal systems. Over the recent years, they have been increasingly investigated due to their potential as skin delivery vehicles for a wide range of drug molecules. The nanoscale particle size and the specificity of microemulsion components are the main features determining the skin permeation process. However, in order to effectively cross the skin barrier, the active...
-
The extended version of restriction analysis approach for the examination of the ability of low-molecular-weight compounds to modify DNA in a cell-free system
PublikacjaOne of the primary requirements in toxicology is the assessment of ability of chemicals to induce DNA covalent modification. There are several well-established methods used for this purpose such as 32P-Postlabeling or HPLC-MS. However, all of these approaches have difficult to overcome limitations, which prevents their use in genotoxin screening. Here, we describe the simple protocol exploiting specificity of restriction enzymes...
-
Nodal models of Pressurized Water Reactor core for control purposes – A comparison study
PublikacjaThe paper focuses on the presentation and comparison of basic nodal and expanded multi-nodal models of the Pressurized Water Reactor (PWR) core, which includes neutron kinetics, heat transfer between fuel and coolant, and internal and external reactivity feedback processes. In the expanded multi-nodal model, the authors introduce a novel approach to the implementation of thermal power distribution phenomena into the multi-node...
-
Modeling with the Anaerobic Digestion Model No. 1 for Enhanced Understanding and Application of Anaerobic Treatment Processes
PublikacjaMathematical model is a valuable tool for prediction and recovery of resources and energy through anaerobic digestion of organic wastes. The International Water Association (IWA) Anaerobic Digestion Model No. 1 (ADM1) is the most commonly used structured anaerobic digestion model. However, as substrates become more complex and our deeper understanding of the anaerobic digestion mechanism, both systematic and specific modifications...
-
Application of human bile salts for in vitro digestion models
PublikacjaIn this study, experimental in vitro models simulating the environment of the human gastrointestinal tract were used to assess the impact of physiological surfactants, such as bile salts, on the kinetics of digestion. Bile salts are biosurfactants synthesised in the liver and secreted together with bile into the small intestine. There are many reports on the role of bile salts in lipolysis, but the knowledge of their influence...
-
Cost-effective methods of fabricating thin rare-earth element layers on SOC interconnects based on low-chromium ferritic stainless steel and exposed to air, humidified air or humidified hydrogen atmospheres
PublikacjaMost oxidation studies involving interconnects are conducted in air under isothermal conditions, but during real-life solid oxide cell (SOC) operation, cells are also exposed a mixture of hydrogen and water vapor. For this study, an Fe–16Cr low-chromium ferritic stainless steel was coated with different reactive element oxides – Gd2O3, CeO2, Ce0.9Y0.1O2 – using an array of methods: dip coating, electrodeposition and spray pyrolysis....
-
Mangiferin Affects Melanin Synthesis by an Influence on Tyrosinase: Inhibition, Mechanism of Action and Molecular Docking Studies
PublikacjaMangiferin is a strong antioxidant that presents a wide range of biological activities. The aim of this study was to evaluate, for the first time, the influence of mangiferin on tyrosinase, an enzyme responsible for melanin synthesis and the unwanted browning process of food. The research included both the kinetics and molecular interactions between tyrosinase and mangiferin. The research proved that mangiferin inhibits tyrosinase...
-
A review on carbon storage via mineral carbonation: Bibliometric analysis, research advances, challenge, and perspectives
PublikacjaMineral carbonation as a way of carbon storage has received a particular attention in the reduction of carbon dioxide (CO2) emission . This work gives a comprehensive description of the research trends and hotspots in the field of mineral carbonation for carbon storage based on bibliometric analysis. A total of 1507 articles were collected from the Web of Science database from 2010 to 2022 and analyzed in details, using a Citepace...
-
Process Control and Investigation of Oxidation Kinetics of Postoxidative Effluents Using Gas Chromatography with Pulsed Flame Photometric Detection (GC-PFPD)
PublikacjaThis article presents the results of investigations on the use of headspace analysis and gas chromatography with pulsed flame photometric detection (HSA-GC-PFPD) to evaluate the effectiveness of oxidation of postoxidative effluents from the production of bitumens. Samples of effluents from the bitumen oxidation unit were used in the experiments. In addition, the kinetics of effluent oxidation was also investigated. The content...
-
Methodology for determining the elemental composition, as well as energy and ignition properties of the low-sulfur marine fuels
PublikacjaThe key metrological issue of substance and energy balance in research engines is the precise determination of the elemental composition of the applied fuel and its net calorific value. This makes it possible to calculate the amount of heat brought with the fuel into the combustion chamber, as well as the amount and gas composition of the exhaust. However, to fully assess the energy quality of the fuel used, its ignition properties...
-
Investigation of the electrochemical behaviour of AA1050 aluminium alloy in aqueous alkaline solutions using Dynamic Electrochemical Impedance Spectroscopy
PublikacjaThe paper presents the electrochemical behaviour of aluminium alloy AA1050 in aqueous alkaline media in the pH range 14–8.5. Electrochemical study was applied in order to obtain comprehensive information on the mechanism and kinetics of the process of anodic dissolution of aluminium, supplemented by monitoring of surface topography using an electron microscope. The corrosion rate of AA1050 increases with increasing concentration...
-
Tuning of the Electrochemical Properties of Transparent Fluorine-doped Tin Oxide Electrodes by Microwave Pulsed-plasma Polymerized Allylamine
PublikacjaWe report here the dry, one-step, and low-temperature modification of FTO surfaces using pulsed plasma polymerization of allylamine (PPAAm). PPAAm/FTO surfaces were characterized by X-ray photoelectron spectroscopy, spectroscopic ellipsometry, and contact angles to understand the morphological, structural, and optical properties. FTO were coated with a very thin layer of adherent cross-linked, pinhole-, and additive-free allylamine...
-
From Structure to Luminescent Properties of B2O3-Bi2O3-SrF2 Glass and Glass-Ceramics Doped with Eu3+ Ions
PublikacjaGlass-ceramics with the composition B2O3 -Bi2O3 -SrF2 were synthesized by the conventional melt-quenching technique and subsequent crystallization of the parental glasses. The temperature at which the ceramization was carried out was selected based on differential scanning calorimetry (DSC) analysis. The structure of the studied materials and the formation of SrF2 nanocrystals were confirmed by the Fourier-transform infrared spectroscopy...
-
Determination of COD Fractionation as a Key Factor for Appropriate Modelling and Monitoring of Activated Sludge Processes
PublikacjaAn operation of wastewater treatment plant is usually controlled by global parameters such as flow, solids retention time, sludge age, concentration of ammonia and dissolved oxygen, etc. It is considered that, together with the chemical and biological oxygen demand (COD and BOD), those parameters indirectly exhibit the effectiveness of activated sludge processes. Especially the BOD indicate the amount of organic pollution that...
-
Surface Charge Density Spectra: Complex Analysis of the Electrical Double Layer Developed from Measurements of Hexanol Adsorption Kinetics
PublikacjaA procedure for deriving surface charge density spectra from differential capacitance data is presented in this study, providing a deeper analysis of the generated charge. A set of simulated differential capacitance spectra was determined for three types of adsorption process control: diffusion control, adsorption control, and mixed control. Based on the differential capacitance curves and spectra, surface charge density spectra...
-
Właściwości katalityczne i biomedyczne związków zawierających jony rutenu(II) oraz rutenu(III)
PublikacjaRuthenium complexes appear in scientific publications mainly as catalysts in the olefins metathesis process. In this review, we want to indicate the research niche regarding the use of ruthenium(II) and ruthenium(III) complexes in other catalytic processes, i.e. polymerization or epoxidation of olefins and depolymerization. We would like to combine the catalytic properties of ruthenium(II,III) complex compounds with their biomedical...
-
Polyurethane Glycerolysate as a Modifier of the Properties of Natural Rubber Mixtures and Vulcanizates
PublikacjaChemical recycling of polyurethanes can be realized in several different ways, but the most important methods are glycolysis and glycerolysis. Both methods permit recovery of polyols (when the process is realized with the mass excess of depolymerizing agent) or substitutes of polyols, which contain urethane moieties in the main chains and terminate mainly in hydroxyl groups (when the process is realized with the mass excess of...
-
Exploring multi-step glucose oxidation kinetics at GOx-functionalized nanotextured gold surfaces with differential impedimetric technique
PublikacjaFor a few past years, we can observe the enormous growth of investigations related to ultrasensitive electrochemical sensors capable of reliable determination of important body parameters and analytes. Utilized procedures rely on standard electrochemical methods, demanding electrode polarization, and information about the initial characteristics of the working electrode. More and more complex electrode materials are characterized...
-
Interactions between polyphenolic antioxidants quercetin and naringenin dictate the distinctive redox-related chemical and biological behaviour of their mixtures
PublikacjaFood synergy concept is suggested to explain observations that isolated antioxidants are less bioactive than real foods containing them. However, mechanisms behind this discrepancy were hardly studied. Here, we demonstrate the profound impact of interactions between two common food flavonoids (individual: aglycones quercetin—Q and naringenin—N− or their glycosides rutin—R and naringin—N+ vs. mixed: QN− and RN+) on their electrochemical...
-
Design and Analysis of Artificial Neural Network (ANN) Models for Achieving Self-Sustainability in Sanitation
PublikacjaThe present study investigates the potential of using fecal ash as an adsorbent and demonstrates a self-sustaining, optimized approach for urea recovery from wastewater streams. Fecal ash was prepared by heating synthetic feces to 500 °C and then processing it as an adsorbent for urea adsorption from synthetic urine. Since this adsorption approach based on fecal ash is a promising alternative for wastewater treatment, it increases...
-
High-temperature oxidation of the Crofer 22 H ferritic steel with Mn1.45Co1.45Fe0.1O4 and Mn1.5Co1.5O4 spinel coatings under thermal cycling conditions and its properties
PublikacjaThe aim of the presented study was to deposit protective-conducting Mn1.45Co1.45Fe0.1O4 and Mn1.5Co1.5O4 spinel coatings on the Crofer 22 H ferritic steel by means of electrophoresis and to evaluate their physicochemical properties after high-temperature oxidation under thermal cycling conditions. When the Crofer 22 H steel – whether uncoated or coated with the two spinels – was oxidized in 48-h cycles involving a temperature of...
-
SORPTION OF SELECTED CHLORINATED SOLVENTS ON PLANT DEBRIS COLLECTED IN A CITY PARK
PublikacjaDebris from deciduous trees in the form of park green waste was investigated as a potential biosorbent for the removal of chlorinated solvents from water. The sorption properties of beech leaves and cupules, oak leaves and acorns, birch leaves and lime leaves (all tree species common for a moderate climate) in a non-modified form were investigated with regard to the removal of perchloroethylene, 1,1,2-trichloroethane and 1,1,1,2-tetrachlorothane....