Wyszukiwarka
Filtry
wszystkich: 115
Wyniki wyszukiwania dla: amorphous carbon
-
WEAR OF Si OR B DOPED AMORPHOUS CARBON COATINGS
PublikacjaThe paper describes a complex wear research on DLC (amorphous carbon) moped with boron (B) and silicone (Si). The tests were carried out in two different sliping systems: flat–on–flat (ring contact, unidirectional sliding) and ball–on–flat (reciprocating sliding). Water and medical saline solutions were used as lubricants. A comparative analysis of the results revealed differences in the initiation and progress of wear and the...
-
Structure and thermoelectric properties of bismuth telluride—Carbon composites
PublikacjaCarbon nanotubes and amorphous carbon have been introduced into a bismuth telluride matrix (0.15 and 0.30 wt.% ratio) to investigate the influence of the carbon on the composite’s thermoelectric properties. Composites with well-dispersed additives have been obtained by sonication and ball-milling methodology. Carbon nanotubes and an amorphous carbon addition led to a decrease in electric conductivity from 1120 S/cm to 77 S/cm....
-
Blends of amorphous/crystalline nanoalumina and hydrophobic amorphous nanosilica
Publikacja -
Kinetics of carrier recombination in amorphous solids
PublikacjaPrzeanalizowano zależność pomiędzy teoriami Simmonsa-Taylora oraz Rose´a, opisującą niestacjonarne procesy rekombinacji nośników nadmiernych, ich pułapkowania i uwalniania ze stanów zlokalizowanych. Równania Simmonsa-Taylora wyrażono w warunkach gęstości nośnika w stanach zlokalizowanych. Pokazano, że w pewnych przypadkach równania redukują się do równań Rose´a, odnoszących się do bimolekularnej lub monomolekularnej rekombinacji.
-
Chemical properties of bismuth telluride – carbon composites.
Dane BadawczeCarbon nanotubes and amorphous carbon have been introduced into bismuth telluride matrix (in 0.15 and 0.30 wt % ratio) in order to investigate influence of carbon on composite’s thermoelectric properties. Composites with well-dispersed additives have been obtained by sonication and ball-milling. Chemical composition of materials was confirmed by XPS...
-
Superconductivity in amorphous thin films of tin–copper
Publikacja -
Impact of low-temperature sintering on the Fe-based amorphous coatings
PublikacjaBulk metallic glasses (BMGs) have gained a lot of attention in recent years due to their outstanding properties such as high hardness and excellent wear and corrosion resistance. However, they are restricted in industrial applications due to their extreme brittleness. Iron based amorphous coatings from BMGs are the best solution to use them by overcoming the problem of extreme brittleness. The coatings can be sprayed by various...
-
A method of determination of electrical conduction mechanisms in complex amorphous materials
PublikacjaA novel approach to determine conduction mechanisms in complex amorphous materials was presented and tested on a real system. In the first step of the presented method, total electrical admittance of the material is analyzed in order to separate a couple of processes, each of which can be described by Jonscher's universal dielectric response. In the following step, a temperature dependence of dielectric response parameters of the...
-
Amorphous Form of Carvedilol Phosphate—The Case of Divergent Properties
Publikacja -
Low current transformer utilizing Co-based amorphous alloys
PublikacjaMetal oxide surge arresters have been widely used for protection of power system networks against overvoltages due to atmospheric discharges or malfunction of devices connected to the network. During its operation a surge arrester structure is degradated, what can be observed as an increase of a surge arrester leakage current. Paper presents an implementation of a new, high-permeability, Co64Fe4Ni1Si15B14 amorphous alloy as a current...
-
Low Current Transformer Utilizing Co-Based Amorphous Alloys
PublikacjaMetal oxide surge arresters have been widely used for protection of power system networks against overvoltages due to atmospheric discharges or malfunction of devices connected to the network. During its operation a surge arrester structure is degradated, what can be observed as an increase of a surge arrester leakage current. Paper presents an implementation of a new, high-permeability, Co64Fe4Ni1Si15B14 amorphous alloy as a current...
-
Blowing Kinetics, Pressure Resistance, Thermal Stability, and Relaxation of the Amorphous Phase of the PET Container in the SBM Process with Hot and Cold Mold. Part I: Research Methodology and Results
PublikacjaThe technology of filling drinks without preservatives (such as fresh juices, iced tea drinks, vitaminized drinks) is carried out using hot filling. Mainly due to the production costs and lower carbon footprint, polyethylene terephthalate bottles, commonly called PET, are increasingly used in this technology. In this paper, the main aim is to describe the statistical analysis methodology of the influence of the temperature of the...
-
Hydrothermal, microwave and mechanochemical modification of amorphous zirconium phosphate structure
Publikacja -
Blowing Kinetics, Pressure Resistance, Thermal Stability, and Relaxation of the Amorphous Phase of the PET Container in the SBM Process with Hot and Cold Mold. Part II: Statistical Analysis and Interpretation of Tests
PublikacjaThe technology of filling drinks without preservatives (such as fresh juices, iced tea drinks, and vitaminized drinks) is carried out using hot filling. Mainly due to the production costs and lower carbon footprint, polyethylene terephthalate (PET) bottles are increasingly used in this technology. In this paper, the main aim is to describe and interpret the results of statistical analysis of the influence of the temperature of...
-
A Molecular dynamics study of the influence of chemical reduction on the structure of amorphous germania
PublikacjaPraca poświęcona jest badaniom struktury blisko- i średniozasięgowej redukowanego amorficznego tlenku germanu o składzie 1Ge 1GeO2 za pomocą symulacji dynamiczno-molekularnych. Symulacje MD realizowano w zespole mikrokanonicznym (NVE), z wykorzystaniem dwuciałowego potencjału oddziaływania miedzyatomowego Borna-Mayera-Hugginsa. Wyraźnie widoczna tendencja do aglomeracji neutralnych atomów Ge została porównana z tendencją do aglomeracji...
-
The structure of porous and spontaneously densified amorphous PbSiO3: a Molecular Dynamics study.
PublikacjaW pracy zaproponowano nową metodę numerycznego otrzymywania strukturporowatych metodą dynamiki molekularnej. Metoda polega na rozpoczęciu symulacji z ładunkami ekranowanymi i stopniowym zwiększaniu ich do pełnych ładunków jonowych. Metodę zastosowano do układu PbSiO3.
-
Thermally stimulated currents in amorphous solids due to complex heating regimes
PublikacjaPodano opis teoretyczny prądów termicznie stymulowanych w ciałach amorficznych. Dokonano rozszerzenia istniejących wzorów przybliżonych na przypadki opóźnionego i krokowego ogrzewania próbki. Otrzymane wyrażenia zweryfikowano za pomocą obliczeń numerycznych dla przypadku wykładniczego rozkładu pułapek.
-
Role of nitrogen in optical and electrical band gaps of hydrogenated/hydrogen free carbon nitride film
PublikacjaWe report the optical and electrical band gap energy of amorphous hydrogenated carbon nitride (a-HCNx) and carbon nitride (a-CNx) as a function of nitrogen concentration (N/C). The optical band gap of a-HCNx and a-CNx films has been determined by means of Ellipsometry and UV-VIS. Both optical and electrical band gaps increase with elevated nitrogen concentration. Experimentally obtained electrical band gap is compared with the...
-
Influence of alkali metal cations on the photoactivity of crystalline and exfoliated amorphous WO3 – photointercalation phenomenon
PublikacjaIn order to investigate the effect of photointercalation on photoelectrochemical properties, two types of WO3-based photoanodes, bulk and exfoliated have been prepared and investigated. An aqueous exfoliation method is introduced for the simple fabrication of amorphous and hydrated WO3 nanomaterial using commercial bulk WO3 precursor. The comparison of obtained material with bulk WO3 was performed using Raman, UV–vis, and XPS as...
-
Influence of sample thickness non-uniformities on the modulated photocur-rents in amorphous solids
PublikacjaOtrzymano przybliżone wzory opisujące modulowane fotoprądy dla przypadków próbki kanapkowej o nierównomiernej grubości, reprezentowanej przez układ równolegle połączonych próbek o różnych grubościach. Na ich podstawie obliczono przebieg fotoprądów dla przypadku jednorodnego i gaussowskiego rozkładu grubości próbki oraz dla wykładniczego rozkładu pułapek.
-
Nonlinear optical birefringence in Li2SO4-MgO-P2O5 amorphous system -influence of Cu ions
Publikacja -
Evaluation of the Microstructure and Magnetic Properties of Fe73Me5Y3B19 (Where Me = Ti or Nb) Amorphous Alloys
Publikacja -
Silicon oxycarbide ceramics as anodes for lithium ion batteries: influence of carbon content on lithium storage capacity
PublikacjaWe report here on the synthesis and characterization of silicon oxycarbide (SiOC) in view of its application as a potential anode material for Li-ion batteries. SiOC ceramics are obtained by pyrolysis of various polysiloxanes synthesized by sol–gel methods. The polysiloxanes contain different organic groups attached to silicon, which influence the chemical composition and the microstructure of the final ceramic product. The structure...
-
Initial stage of (Bi-Pb)2Sr2Ca1Cu2Ox high Tc superconductor crystallisation from the amorphous phase.
PublikacjaWysokotemperaturowe nadprzewodniki bizmutowe 2201, 2212 i 2223 były wytwarzane metodą krystalizacji w fazie stałej. Zmiany struktury i mikrostruktury badano metodą dyfrakcji rentgenowskiej oraz skanningowej mikroskopii elektronowej. Zbadano kinetykę krystalizacji oraz przedyskutowano jej przebieg.
-
Thermally stimulated currents in amorphous solids at mixed carrier recombination, Part I: Non-equilibrium approximation
PublikacjaPodano opis teoretyczny prądów termicznie stymulowanych dla przypadku mieszanej rekombinacji nośników ładunku, przy założeniu początkowego zapełnienia głębokich stanów pułapkowych oraz silnie nierównowagowego rozkładu nośników w aktywnych pułapkach. Otrzymane wyrażenia zweryfikowano za pomocą obliczeń numerycznych dla przypadku wykładniczego rozkładu pułapek.
-
Lignin-based carbon fibers for renewable and multifunctional lithium-ion battery electrodes
PublikacjaLignin-based carbon fibers (LCFs) from the renewable resource softwood kraft lignin were synthesized via oxidative thermostabilization of pure melt-spun lignin and carbonization at different temperatures from 1000°C to 1700°C. The resulting LCFs were characterized by tensile testing, scanning electron microscopy (SEM), X-ray diffraction (XRD) and confocal Raman spectroscopy. The microstructure is mainly amorphous carbon with some...
-
Role of nitrogen in evolution of sp2/sp3 bonding and optical band gap in hydrogenated carbon nitride
PublikacjaDrastic changes in the bonding are found in amorphous hydrogenated carbon nitride (a-CNx:H) film as a function of nitrogen concentration (or N/C ratio). The total C-sp3 fraction and hardness shows a sharp decrease (at N/C = 0.40) whereas optical band gap and resistivity shows a gradual increase as nitrogen concentration increases from 0.07 to 0.58. Raman spectrum of a-CNx:H film is fitted with both Gaussian (integrated intensity...
-
DETERMINATION OF SP3 FRACTION IN ta-C COATING USING XPS AND RAMAN SPECTROSCOPY
PublikacjaThe paper presents results of studies on the structure of tetrahedral amorphous carbon films (ta-C) with a thickness in the range from 20 to 280 nm, deposited using pulsed vacuum arc technique with an electromagnetic Venetian blind plasma filter. The results of the phase structure analysis, obtained using visible Raman spectroscopy and UV Raman spectroscopy methods, showed a strong dependence of the results on the presence, on...
-
The influence of amorphous macrodiol, diisocyanate type and l-ascorbic acid modifier on chemical structure, morphology and degradation behavior of polyurethanes for tissue scaffolds fabrication
PublikacjaStudies described in this work were related to the bulk synthesis and characterization of polyurethanes (PURs) obtained with the use of cyclic 4,4′-methylene bis(cyclohexyl isocyanate) (HMDI) or linear 1,6-hexamethylene diisocyanate (HDI), amorphous α,ω-dihydroxy(ethylene-butylene adipate) macrodiol (PEBA), 1,4-butandiol (BDO) chain extender and dibutyltin dilaurate (DBTDL) catalyst. Obtained PURs were modified with l-ascorbic...
-
Tribo-Environment Dependent Chemical Modification of Sliding Interfaces in Ultrananocrystalline Diamond Nanowall Film: A Correlation with Friction and Wear
PublikacjaTribological properties of ultrananocrystalline diamond nanowall (UNCD NW) films were investigated quantitatively in three different and controlled tribo-environmental conditions, proposing the passivation and graphitization mechanisms. However, these mechanisms are rather complicated and possibly can be understood in well-controlled tribological conditions. It was shown that the friction and wear of these films were high in highPage 1...
-
Influence of Ni ion site occupancy on laser induced third harmonic generation (THG) studies in Li2SO4–MgO–P2O5 amorphous system
Publikacja -
Tuning the Laser-Induced Processing of 3D Porous Graphenic Nanostructures by Boron-Doped Diamond Particles for Flexible Microsupercapacitors
PublikacjaCarbon (sp3)-on-carbon (sp2) materials have the potential to revolutionize fields such as energy storage and microelectronics. However, the rational engineering and printing of carbon-on-carbon materials on flexible substrates remains a challenge in wearable electronics technology. This study demon-strates the scalable fabrication of flexible laser-induced graphene (LIG)-boron doped diamond nanowall (BDNW) hybrid nanostructures...
-
Ellipsometric investigation of nitrogen doped diamond thin films grown in microwave CH4/H2/N2 plasma enhanced chemical vapor deposition
PublikacjaThe influence of N2 concentration (1%–8%) in CH4/H2/N2 plasma on structure and optical properties of nitrogen doped diamond (NDD) films was investigated. Thickness, roughness, and optical properties of the NDD films in the VIS–NIR range were investigated on the silicon substrates using spectroscopic ellipsometry. The samples exhibited relatively high refractive index (2.6 6 0.25 at 550 nm) and extinction coefficient (0.05 6 0.02...
-
Structure versus hydrolytic and thermal stability of bio-based thermoplastic polyurethane elastomers composed of hard and soft building blocks with high content of green carbon
PublikacjaNowadays, sustainability plays a key role in the design and synthesis of new materials. One of the methods for the preparation of green materials is incorporation into their structure the monomers with a high content of green carbon. Therefore, the aim of this work was to investigate the influence of the type and molecular mass of two bio-based polyester polyols and bio-glycol on the properties of aliphatic partially bio-based...
-
Composite Materials Based on Polymer-Derived SiCN Ceramic and Disordered Hard Carbons as Anodes for Lithium-Ion Batteries
PublikacjaNew composite materials based on polymer-derived SiCN ceramics and hard carbons were studied in view of its application as anodes for lithium-ion batteries. Two kinds of composites were prepared by pyrolysis of the preceramic polysilazane (HTT1800, Clariant) at 1000 °C in Ar atmosphere mixed with hard carbons derived from potato starch (HC_PS) or with a hard carbon precursor, namely potato starch (PS), denoted as HTT/HC_PS and...
-
Tailoring of SiOC composition as a way to better performing anodes for Li-ion batteries
PublikacjaPolymer derived silicon oxycarbide (SiOC) ceramics are investigated as potential anodes for lithiumion batteries. Different SiOC ceramics are prepared by pyrolysis (1000 °C and 1400 °C under controlled argon atmosphere) of polysiloxanes ceramic precursors. Preceramic polymers are synthesized using the sol–gel method. Phenyltriethoxysilane (PhTES) and methyltriethoxysilane (MTES) have been used as starting precursors and mixed with...
-
Preparation and Characterization of Nanomaterial Consisting of Silica Aerogel & Carbon Tested as an Electrode in Non-Aqueous Media Containing Lithium Salt.
PublikacjaSilica aerogel (SiO2ag) was combined with carbonaceous material in the pyrolysis process of hydrocarbons. The obtained nanocomposite SiO2ag/C was amorphous, partially preserving the porous structure of SiO2ag. The specific surface area changes from 445.6 m2/g for pure SiO2ag to 205.52 m2/g SiO2ag/C. The 29Si MAS-NMR shows a three-dimensional matrix with silicon atoms connected to other silicon atoms by four...
-
Gas Composition Influence on the Properties of Boron-Doped Diamond Films Deposited on the Fused Silica
PublikacjaThe main subject of this study are molecular structures and optical properties of boron-doped diamond films with [B]/[C] ppm ratio between 1000 and 10 000, fabricated in two molar ratios of CH 4 -H 2 mixture (1 % and 4 %). Boron-doped diamond (BDD) film on the fused silica was presented as a conductive coating for optical and electronic purposes. The scanning electron microscopy images showed homogenous and polycrystalline surface...
-
Optoelectronic system for monitoring of thin diamond layers growth
PublikacjaDevelopment of the optoelectronic system for monitoring of diamond/DLC (Diamond-Like-Carbon) thin films growth during mu PA ECR CVD (Microwave Plasma Assisted Electron Cyclotron Resonance Chemical Vapour Deposition) process is described. The multi-point Optical Emission Spectroscopy (OES) and Raman spectroscopy were employed as non-invasive optoelectronic tools. Dissociation of H-2 molecules, excitation and ionization of hydrogen...
-
SILICA AEROGEL TOWARDS ANODES FOR LITHIUM-ION BATTERIES
PublikacjaAn increasing demand for electrochemical energy storage and conversion devices stimulates progress in research on electrode and electrolyte materials. In the field of electrodes materials, silicon is the one of the most promising anode materials for Li-ion batteries. However silicon has the drastic volume variation (around 3 times lower on extraction) during insertion and extraction of lithium ions. As an alternative, nanocomposites...
-
Effect of electron count and chemical complexity in the Ta-Nb-Hf-Zr-Ti high-entropy alloy superconductor
PublikacjaHigh-entropy alloys are made from random mixtures of principal elements on simple lattices, stabilized by a high mixing entropy. The recently discovered body-centered cubic (BCC) Ta-Nb-Hf-Zr-Ti high-entropy alloy superconductor appears to display properties of both simple crystalline intermetallics and amorphous materials; e.g., it has a well-defined superconducting transition along with an exceptional robustness against disorder....
-
Influence of electropolymerization temperature on corrosion, morphological and electrical properties of PPy doped with salicylate on iron
PublikacjaIn this work, the influence of the electropolymerization temperature on corrosion, morphological and electrical properties of polypyrrole (PPy) film is studied. Polypyrrole is electrochemically synthesized on iron in the presence of sodium salicylate. The X-ray diffraction and scanning electron microscopy are performed in order to study the structure and morphology of electrodeposited PPy. The electroactive surface area, corrosion...
-
Influence of the ionic strength on the amyloid fibrillogenesis of hen egg white lysozyme
PublikacjaThe study investigates the role of the electrostatic interactions in the fibrillation of the hen egg white lysozyme (HEWL). In order to achieve this aim the influence of the cations Na+, Mg2+ and Al3+ on the amyloid fibril formation and amorphous aggregation was tested. The amyloids are formed in the solution without added salt but the Thioflavin T fluorescence gives the false-negative result. In these conditions, the HEWL fibrils...
-
Phase separation in poly(butylene terephthalate)-based materials prepared by solid-state modification
PublikacjaThe morphology of a series of poly(butylene terephthalate) (PBT)/fatty acid dimer diol (FADD)-based copolyesters prepared by solid-state modi fi cation (SSM) was studied. It was shown that in copolyesters containing less than 10 wt% FADD two different phases, i.e. a PBT crystalline phase and a PBT-rich amorphous phase, are present. The FADD residues were more or less homogeneously distributed throughout the interlamellar regions....
-
Origin of bitumen fractions in the Jurassic-early Cretaceous Vaca Muerta Formation in Argentina: insights from organic petrography and geochemical techniques
PublikacjaThis paper investigates chemical functional groups of the two extracted bitumen fractions in shales of the Jurassic to early Cretaceous Vaca Muerta Formation of the Neuquén Basin in Argentina, South America. The results indicate that Bitumen I is strongly aliphatic and appears to be genetically related to fluorescent amorphous organic matter. In contrast, Bitumen II consists of highly condensed, aromatic hydrocarbons, and has some...
-
The Effect of Calcination Temperature on Structure and Photocatalytic Properties of WO3/TiO2 Nanocomposites
PublikacjaSeries ofWO3/TiO2 nanocompositeswere obtained by hydrothermal method followed by calcination in the temperature range from 400∘C to 900∘C. The characteristics of photocatalysts by X-ray diffractometry (XRD), scanning electron microscope (SEM), and diffuse reflectance spectroscopy (DRS) showed that increasing the calcination temperature from 400 to 900∘C resulted in change of photocatalytic activity under UV-Vis light.Moreover,...
-
Transition Metal Oxides influence on phosphate and borate glasses structure
PublikacjaBorate and phosphate glasses possess many potential luminescence and optical applications. With their low melting point, they are one of the most often studied amorphous materials. In recent years these glasses, doped with transition metal oxides (TMO), gained much attention due to their tunable structural and thermal properties. Review of systems containing TMOs was presented. Additionally synthesis of binary MnO-P2O5 and MnO-B2O3...
-
The In-Depth Studies of Pulsed UV Laser-Modified TiO2 Nanotubes: The Influence of Geometry, Crystallinity, and Processing Parameters
PublikacjaThe laser processing of the titania nanotubes has been investigated in terms of morphology, structure, and optical properties of the obtained material. The length of the nanotubes and crystallinity, as well as the atmosphere of the laser treatment, were taken into account. The degree of changes of the initial geometry of nanotubes were checked by means of scanning electron microscopy, which visualizes both the surface and the cross-section....
-
Synthesis and characterization of novel aliphatic polyurethanes for tissue engineering applications
PublikacjaSummarizing, in this thesis was described the synthesis of novel PUR system, which was obtained by using aliphatic diisocyanate (HDI), amorphous macrodiol (PEBA) and chain extender (BDO). This PUR system was established as suitable for TE purpose and successfully modified with AA, which as expected improved its biocompatibility. According to this, AA-modified HDI-based PURs is the PUR system ready for further studies including...
-
Manufacture and research of TPS/PE biocomposites properties
PublikacjaIn this paper the process of native starch preparing for modification by extrusion and manufacture of biocomposites is presented. The first aim of this study was to determine the mixing and granulating condition of native starch to obtain granulated native starch. For mixing and granulation of native starch Intensive Mixer manufactured by Maschinenfabrik Gustav Eirich was used. Mixing and granulation in a single process is a new...