Filtry
wszystkich: 4930
wybranych: 3574
-
Katalog
- Publikacje 3574 wyników po odfiltrowaniu
- Czasopisma 16 wyników po odfiltrowaniu
- Konferencje 5 wyników po odfiltrowaniu
- Osoby 45 wyników po odfiltrowaniu
- Wynalazki 4 wyników po odfiltrowaniu
- Projekty 5 wyników po odfiltrowaniu
- Laboratoria 1 wyników po odfiltrowaniu
- Aparatura Badawcza 4 wyników po odfiltrowaniu
- Kursy Online 183 wyników po odfiltrowaniu
- Wydarzenia 14 wyników po odfiltrowaniu
- Oferty 1 wyników po odfiltrowaniu
- Dane Badawcze 1078 wyników po odfiltrowaniu
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: TESTY BIEGŁOŚCI
-
Torque capacity of multidisc wet clutch with reference to friction occurrence on its spline connections
PublikacjaIn this article developed mathematical model that includes friction occurrence on spline connections is presented. The work also contains results of experimental research on torque capacity of multidisc wet clutch. These results are expressed as a function of contact pressure for different number of friction surfaces. Due to increased interest in research concerning multidisc wet clutches it is essential to determine impact of...
-
Quality assessment of low voltage surge arresters
PublikacjaUsers expect reliable operation of the surge arrester during overvoltages, which may originate from a switching process or a lightning discharge. The necessary conditions to guarantee these expectations are: appropriate construction of the surge arrester, its production being maintained in accordance with technical standards, and a positive results of the type test (as well routine and acceptance tests). The recipient, especially...
-
Cavitation wearing of the SUPERSTON alloy after laser treatment at cryogenic conditions
PublikacjaThe purpose of this paper is to demonstrate the method of laser remelting at cryogenic conditions of the SUPERSTON alloy and its influence on microstructure and cavitation wearing. The cavitation test was performed using the rotating disc facility in IPM PAN Gdansk. During the cavitation test, the mass loss of the material with different parameters of laser remelting was determined. Surface and cross-section microstructure of the...
-
Comparison of calculated and measured thermal stresses in asphalt concrete
PublikacjaThe paper presents the comparison of calculated and measured thermal stresses induced in restrained asphalt concrete specimens by cooling. Thermal stresses were measured in the Thermal Stress Restrained Specimen Test. The calculations of thermal stresses were performed with the use of a theoretical formula based on the temperature dependent stiffness modulus. The novel approach applied in this paper was that the stiffness modulus...
-
Kształtowanie nowej tożsamości regionalnej w przestrzeniach dominacji wody na Żuławach Delty Wisły
PublikacjaCelem naukowym rozprawy jest sformułowanie kierunku zagospodarowania przestrzennego regionu Żuław Delty Wisły. To unikatowy w skali europejskiej region, który jest fenomenem cywilizacji hydraulicznej i dominacji wody. Proces polderyzacji, który rozpoczął się już w XIII wieku doprowadził do utworzenia historycznych układów urbanistycznych. W roku 1945 nastąpiło przerwanie ciągłości kulturowej. Współcześnie na obszarze Żuław istnieją...
-
Impact of the inclination angle of the condenser with refrigerant R410A on heat transfer coefficient – experimental study
PublikacjaIn the paper the authors present results of a laboratory test of the condenser with refrigerant R410A. The effect of the inclination of this condenser on the heat transfer coefficient value has been considered. The test has proved that there is an optimal inclination angle of the condenser which gives maximal value of this coefficient.
-
TESTING CONTRACTION AND THERMAL EXPANSION COEFFICIENT OF CONSTRUCTION AND MOULDING POLYMER COMPOSITES
PublikacjaThe paper presents results of systematic tests of contraction and thermal expansion coefficients of materials based on polymer composites. The information on the above material properties is essential both at the design stage and during the use of finished products. Components for the samples were selected in such a way as to represent typical materials used for production of construction and moulding elements. The performed tests...
-
Experimental and numerical evaluation of mechanical behaviour of composite structural insulated panels
PublikacjaComposite structural insulated panels (CSIPs) are novel prefabricated elements for structural applications. Panels under consideration are made from glass-fibre reinforced magnesia cement boards as facesheets and expanded polystyrene foam (EPS) as a core. Quasi-static full-scale and model bending tests under monotonic loading were performed to recognize mechanical properties of CSIPs in flexure. In addition, tensile, compressive,...
-
Accuracy Analysis of Determination the Vertical Displacements in Unstable Reference System
PublikacjaMeasurements of horizontal and vertical displacements are carried out mostly based on reference points identified as fixed. In surveying practice there may be some situations in which there is not possible to perform the measurements with reference to stable points or the difficulties in identification of points’ stability may arise. Accuracy analysis based on the covariance matrices have a special role in this process. In presented...
-
Rigid finite elements and multibody modeling in analyses of a robot shaped elastic/plastic deformations of a beam
PublikacjaDynamics analysis of a system composed of a parallel manipulator and of an elastic beam is presented in the paper. Classic 3RRR parallel manipulator is considered and used to deform the beam. Elasto-plastic deformations are investigated. Rigid-finite-elements technique is employed to deal with dynamics of the beam. A multibody structure is associated with the introduced hybrid system in order to model its dynamics. Idea of the...
-
Prediction of manoeuvring abilities of 10000 DWT pod-driven coastal tanker
PublikacjaThis paper aims to present a new approach in the prediction of manoeuvring abilities of pod-driven ships. A new mathematical model of motions based on MMG methodology was developed and a new type of description of forces acting on azimuth drives is presented. Captive model tests of medium-size coastal tanker and pod open water tests were carried out in CTO S.A. (Ship Design and Research Centre S.A.) to obtain hull hydrodynamic derivatives...
-
Narzędzia kształcenia na odległość i ich wykorzystanie na Wydziałach Inżynierii Lądowej Politechniki Gdańskiej i Warszawskiej.
PublikacjaW artykule przedstawiono doświadczenia we wdrażaniu narzędzi kształcenia na odległość na Wydziałach Inżynierii Lądowej Politechniki Gdańskiej i Warszawskiej. Zaprezentowano tworzenie zasobów edukacyjnych (wykłady, ćwiczenia, testy) oraz wspomaganie zajęć z przedmiotu Podstawy Informatyki przy pomocy darmowej platformy internetowej Moodle. Kształcenie na odległość, internetowa platforma Moodle
-
Porównanie właściwości barierowych i mechanicznych dwóch systemów poliuretanowych na stali węglowej S235JR eksponowanych w warunkach symulujących narażenia występujące w glebie
PublikacjaPorównano właściwości barierowe i mechaniczne próbek powłok na stali dostarczonych przez Zleceniodawcę eksponowanych w trzech środowiskach symulujących narażenia występujące w glebie.Do oceny degradacji w tych środowiskach po 2,5 miesięcznej ekspozycji wykorzystano spektroskopię impedancyjną oraz testy normowe. Wskazano powłokę o korzystniejszych właściwościach ochronnych w warunkach glebowych.
-
Non-destructive diagnostics of concrete cantilever beam and slab by impact echo method = Nieniszcząca diagnostyka konstrukcji betonowych belek wspornikowych i płyty stropowej za pomocą metody impact echo
PublikacjaPraca poświęcona jest zastosowaniu fal sprężystych na przykładzie w metody impact-echo. Metoda ta wykorzystuje zjawisko propagacji fal wzbudzanych przez mechaniczne uderzenie i ich pomiar za pomocą jednego lub dwóch akcelerometrów. Przeprowadzone testy eksperymentalne dla betonowych wsporników oraz stropu potwierdziły skuteczność metody w wykrywaniu uszkodzeń.
-
Próbne obciążenie kompozytowej kładki pieszo-rowerowej
PublikacjaW pracy podano zakres badań zrealizowanych podczas próbnego obciążenia obiektu badawczego stanowiącego pełnowymiarowy kompozytowy most pieszo-rowerowy. Badane przęsło jest elementem projektu FOBRIDGE, który zostało posadowione na obniżonych podporach na terenie kampusu Politechniki Gdańskiej. Wykonano testy statyczne i dynamiczne zgodnie z założonym programem badań.
-
Wieloobszarowy układ regulacji PI do sterowania prędkością obrotową samochodu z silnikiem spalinowym
PublikacjaSterowanie pojazdami stanowi istotny obszar działalności koncernów samochodowych. W pracy przedstawiono nieliniowy model matematyczny układu napędowego samochodu osobowego z silnikiem spalinowym. Następnie zaproponowano strukturę systemu sterowania i zaprojektowano nieliniowy wieloobszarowy układ regulacji PI. Przeprowadzono testy symulacyjne zaproponowanego rozwiązania i dokonano krytycznej analizy uzyskanych wyników.
-
MIC1-MAG1-SAG1 chimeric protein, a most effective antigen for detection of human toxoplasmosis
PublikacjaThis study describes a Toxoplasma gondii IgG ELISA test based on a new chimeric antigen containing three immunodominant regions from MIC1, MAG1 and SAG1 proteins of a parasite and shows that this test is useful for diagnostic purposes and may replace the lysed and whole-cell antigens.
-
System automatyzacji przeprowadzania i oceniania sprawdzianów studenckich
PublikacjaArtykuł prezentuje system pozwalający na przeprowadzenie sprawdzianów studenckich w wersji papierowej oraz na komputerach. Kluczowym aspektem systemu jest moduł umożliwiający przeprowadzenie oraz sprawdzenie tradycyjnego testu, którego pytania będą losowane z utworzonej wcześniej bazy (lub kilku baz) pytań. Trzema głównymi zadaniami aplikacji są następująco: tworzenie i edycja testów oraz zapisywanie ich w bazie pytań, generowanie...
-
Zeszyt wydawniczy Kachu Profesor zwyczajny, Akademia Sztuk Pięknych w Gdańsku
PublikacjaDrugi numer wydawnictwa Akademii Sztuk Pięknych w Gdańsku poświęcony w całości wspomnieniom o profesorze Kazimierzu Ostrowskim, wybitnym malarzu i pedagogu. Publikacja liczy 48 stron i zawiera teksty o profesorze a także 71 biało-czarnych fotografii (teksty autorów s.19, 22, 39). Wydawcą publikacji jest Akademia Sztuk Pięknych w Gdańsku. ISSN 2081-6197.
-
Identification of hydroacoustic wave sources of ship in motion
PublikacjaThis paper deals with results of identification tests of acoustic field spectrum of underwater noise generated by ship in motion. The field is connected with acoustic activity of ship mechanisms and devices in operation. Vibration energy generated by the mechanisms and devices is transferred through ship structural elements to surrounding water where it propagates in the form of acoustic waves of a broad band of frequencies. In...
-
ANALYSIS OF DIESEL OIL SPECIFIC HEAT IMPACT FOR OPERATION OF THE SUPPLY PUMP
PublikacjaThe article describes a test rig that allows the measurement of fuel oil specific heat changes based on the cooling time of liquids. After that, by analysing the test results, a research hypothesis was created and verified. The hypothesis is that the specific heat energy of fuel oil impact the operation of the circulation pump.
-
Virtual Engineering Objects (VEO): Designing, Developing and Testing Models
PublikacjaIn this article, the development and implementation of the concept of Virtual Engineering Object (VEO) is described. A VEO is a computerized real world representation of an engineering object. VEO will act as a living representation of the object capable of adding, storing, improving and sharing knowledge through experience, in a way similar to an expert of that object. In this paper, it is shown through test models how the concept...
-
A Taxonomy of Model-Based Testing for Embedded Systems from Multiple Industry Domains
PublikacjaThis chapter provides a taxonomy of Model-Based Testing (MBT) based on the approaches that are presented throughout this book as well as in the related literature. The techniques for testing are categorized using a number of dimensions to familiarize the reader with the terminology used throughout the chapters that follow. In this chapter, after a brief introduction, a general definition of MBT and related work on available MBT...
-
Thermal stabilization and permanent deformation resistance of LWA/PCM-modified asphalt road surfaces
PublikacjaThis paper presents the results of attempts at reducing the problem of solar overheating of asphalt road pavement surfaces, resulting in weakening and accelerated destruction of the aforementioned structures. To protect pavement surfaces against periodic overheating, standard asphalt mixture AC 16 W 35/50, used for binder course, has been modified by replacing one of the aggregate fractions from the mineral mixture with lightweight...
-
Ecological and Health Effects of Lubricant Oils Emitted into the Environment
PublikacjaLubricating oils used in machines with an open cutting system, such as a saw or harvester, are applied in forest areas, gardening, in the household, and in urban greenery. During the operation of the device with an open cutting system, the lubricating oil is emitted into the environment. Therefore, the use of an oil base and refining additives of petroleum origin in the content of lubricants is associated with a negative impact...
-
Proportional-Derivative and Model-Based Controllers for Control of a Variable Mass Manipulator
PublikacjaIn the paper, numerical analysis of dynamics of a variable mass manipulator is presented. A revolute joints composed manipulator is considered. Payload of the gripper is considered as the only element characterized by unknown value of its mass (variable between subsequent operations). As in other cases of the revolute joints composed manipulators, its behaviour dependents significantly on the pose of the manipulator. When the manipulator...
-
Badania mieszanek mineralno-asfaltowych w niskiej temperaturze
PublikacjaW artykule przedstawiono metody badań w niskiej temperaturze betonu asfaltowego przeznaczonego do warstwy ścieralnej. Przedstawione zostały wyniki badań dla 4 różnych metod badawczych: zginania, pełzania, pośredniego rozciągania oraz rozciągania termicznego przy ograniczonym odkształceniu (test TSRST). Próbki betonu asfaltowego były przygotowywane w laboratorium z wykorzystaniem 3 rodzajów asfaltów: asfaltu zwykłego, asfaltu modyfikowanego...
-
Procesor efektów dźwiękowych do gitary na urządzenia mobilne
PublikacjaW rozdziale przedstawiono sposób działania procesora efektów dźwiękowych do gitary, składającego się z układu elektronicznego i aplikacji pracującej w czasie rzeczywistym na urządzeniach mobilnych z systemem Android. W pierwszej części zaprezentowano układ (przejściówkę) w postaci przedwzmacniacza zasilanego z baterii, do którego podłącza się gitarę oraz urządzenie mobilne. W drugiej części referatu przedstawiono zaś proces przetwarzania...
-
Metody analizy sensorycznej jako narzędzie do oceny uciążliwości zapachowej powietrza atmosferycznego. CZ. II. Charakterystyka metod analizy sensorycznej.
PublikacjaZwiązki chemiczne obecne w powietrzu atmosferycznym i wywołujące nieprzyjemne wrażenia zapachowe mogą wywierać negatywny wpływ na zdrowie i życie człowieka. Wszystkie niepożądane substancje zapachowe, powodujące pobudzenie narządu węchowego, a następnie odczuwanie zapachu, nazywane są odorantami. Do pomiaru reakcji człowieka na bodźce pochodzące z otaczającego środowiska wykorzystuje się metody analizy sensorycznej. Umożliwia to...
-
Procesor efektów dźwiękowych do gitary na urządzenia oparte na systemie Android
PublikacjaW artykule przedstawiono procesor efektów dźwiękowych do gitary, składający się z układu elektronicznego i aplikacji pracującej w czasie rzeczywistym na urządzeniach mobilnych z systemem Android. W pierwszej części referatu przedstawiono proces przetwarzania dźwięku w aplikacji oraz interfejs użytkownika. Interfejs użytkownika napisany został w języku Java, wspartym językiem znaczników XML, zaś przetwarzanie dźwięku, ze względu...
-
On the validation of the LS-DYNA Geo Metro numerical model
PublikacjaThe paper presents experiences gained during work with numerical model of Geo Metro vehicle used for simulations of crash tests with road safety barriers. Attention is drawn to the subject of tire/wheel breakage during collision events. Some methods for improvement of the model are presented in the paper. Several results for the normative vehicle numerical tests are introduced. Simulations were carried out using LS-DYNA finite...
-
REALIZACJA INTERFEJSU CTI W SOFTSWITCHACH
PublikacjaW artykule przedstawiono problem zastosowania i realizacji interfejsów CTI w architekturze softswitcha. Dokonano analizy, pod kątem funkcjonalności, dwóch standardów CTI: CSTA oraz Parlay/OSA. Następnie wykonano model softswitcha z interfejsem CTI w standardzie CSTA w oparciu o projekt FreeSWITCH, na którym to modelu przeprowadzono testy i badania.
-
BADANIA ODBIOROWE KOMPOZYTOWEJ KŁADKI NAD KANAŁEM RADUNI W PRUSZCZU GDAŃSKIM
PublikacjaW pracy przedstawiono wyniki badań przeprowadzonych podczas próby obciążeniowej kładki kompozytowej GFRP w Pruszczu Gdańskim. Badania obejmowały zarówno testy statyczne, jak i dynamiczne. Uzyskane wyniki wskazują na większą niż teoretycznie oczekiwaną sztywność przestrzenną konstrukcji. Wszystkie pomierzone parametry struktury były lepsze podczas pomiarów in-situ, niż wykazały analizy numeryczne.
-
Integracja pomiarów inercyjnych i magnetycznych jako metoda zwiększenia dokładności estymaty położenia poruszającej się osoby
PublikacjaW artykule przedstawiono implementację oraz analizę metody integracji pomiarowych danych inercyjnych i magnetycznych do zwiększenia dokładności estymaty położenia poruszającej się osoby. Zaprezentowana metoda bazuje na integracji dwóch, niezależnych systemów kursowych w oparciu o adaptacyjny filtr Kalmana. W celu weryfikacji opisanej koncepcji, przeprowadzono testy funkcjonalne w warunkach rzeczywistych.
-
Damage Development on the Surface of Nickel Coating in the Initial Period of Erosion
PublikacjaThe common occurrence of the phenomenon of cavitation in many industries and the multitude of factors affecting the resistance to cavitation erosion of used materials contribute to the search for methods and appropriate parameters of coating application that are able to minimize the effects of erosion. To determine the validity of the developed application parameters and the method used, cavitation studies and microscopic observations...
-
Effects of the Origin and Deacetylation Degree of Chitosan on Properties of Its Coatings on Titanium
PublikacjaThe properties of chitosan coatings on titanium surfaces may be influenced by a variety of factors, including their chemical characteristics and the deposition method. The aim of this research was to determine the influence of a chitosan’s origin (a type of shrimp) and deacetylation degree (DD), when deposited on a very smooth titanium surface, on adhesion and biological behavior. The tests were performed using chitosan of a degree...
-
Retrievable strain measuring system in screw displacement piles - readings and results interpretation problems
PublikacjaStatic load tests on foundation piles are generally carried out in order to determine load – displacement characteristic of the pile. For more detailed information, e.g. force distribution along the shaft, load transfer mechanism and characteristics of soil-structure interaction (unit resistance curves t-z, q-z) additional pile instrumentation is required. Most popular techniques focus on direct concrete strain measurements and...
-
Numerical Determination of the Load-Bearing Capacity of a Perforated Thin-Walled Beam in a Structural System with a Steel Grating
PublikacjaThis article presents the results of numerical simulations of a structural system consisting of steel perforated thin-walled beams and a steel grating. The simulations were conducted using the finite element method. The analysis took into account physical and geometric nonlinearity as well as the contact between the steel grating and the beams. The main goal of the research was to develop load-bearing curves for the main beam in...
-
Experimental investigations and damage growth modeling of EN‐AW 2024 aluminum alloy under LCF loading accounting creep pre‐deformation
PublikacjaThis article presents the results of experimental tests of creep rupture and of low-cycle fatigue (LCF) of EN-AW 2024 aluminum alloy devoid of damage and having preliminary damage. The preliminary damage was dealt in the process of creep at elevated temperature 100C, 200C, and 300C until achievement of two different strain values at each temperature. Samples with preliminary damage were subjected to fatigue tests at room temperature....
-
The effect of elevated temperature on LCF damage growth in 2024AA – Experiment and modeling
PublikacjaThis paper presents the results of experimental low-cycle fatigue (LCF) tests conducted on EN-AW 2024 alloy in T3511 temper at 100 ◦C, 200 ◦C and 300 ◦C. The material’s basic fatigue characteristics were determined, such as fatigue life curve and cyclic strain curve. Both the hysteresis loop and nature of fracture surfaces obtained in macro- and microscopic observations (scanning electron microscope, SEM) were accounted for. The...
-
Torque Transmitted by Multi-plate Wet Clutches in Relation to Number of Friction Plates and Their Dimensions
PublikacjaIn the paper results of experimental tests on multi-plate wet clutch torque capacity for various diameters and numbers of friction plates are presented. Construction of an apparatus for laboratory tests of wet clutch engagement, drag torque and maximum torque is shown. Methodology of maximum torque capacity experiment and hydraulic circuit diagram, which supplies a motor and an actuator for the experiment are described. Analytically...
-
Zagadnienia tribologiczne w hamulcu silnika hydraulicznego
PublikacjaPrzedmiotem badań był prototypowy hamulec cierny wielopłytkowy do silnika satelitowego SM-0,6 o teoretycznej objętości roboczej 16,7 cm3/obr. Hamulec ten zbudowany był z 27 tarcz ciernych wykonanych z materiału TOLOX oraz z pakietu sprężyn talerzowych zamontowanych w układzie X. Zablokowanie hamulca następuje w skutek siły docisku pakietu sprężyn talerzowych płytek ciernych co następuje w chwili spadku ciśnienia w komorze tłoka...
-
Mechanical response of human thoracic spine ligaments under quasi-static loading: An experimental study
PublikacjaPurpose This study aimed to investigate the geometrical and mechanical properties of human thoracic spine ligaments subjected to uniaxial quasi-static tensile test. Methods Four human thoracic spines, obtained through a body donation program, were utilized for the study. The anterior longitudinal ligament (ALL), posterior longitudinal ligament (PLL), capsular ligament (CL), ligamenta flava (LF), and the interspinous ligament and...
-
The dependence of linear viscoelasticity limits of cold-recycled mixtures on time of curing and compaction method
PublikacjaCold-recycled mixtures are currently among the most widely used and investigated methods that enable recycling of old pavement structures in an environmentally friendly manner. Upon milling, the old pavement structure – whose gradation can be improved with addition of virgin aggregate – is mixed and compacted at ambient temperature. The main binding agents are bituminous emulsion and cement. Due to their dual binding behaviour,...
-
Discussion of “CPT Evaluation of Yield Stress Profiles in Soils” by Shehab S. Agaiby and Paul W. Mayne
PublikacjaVeryfication of the procedure to estimate overconsolidation ratio in sands using the results of mini-cone penetration tests in centrifuge.
-
Transmisja danych w kanałach rozmównych systemów komórkowych.
PublikacjaW niniejszym referacie opisano budowę i dzialanie modemu, przeznaczonego do transmisji danych w kanałach rozmównych systemów komórkowych. Wykonano testy funkcjonalne poprawności działania zbudowanego modemu w kanale rozmównym TCH/FS systemu GSM. Przedstawiono również zastosowane protokoły komunikacyjne wymiany informacji pomiędzy modem a komputerem oraz podczas transmisji danych poprzez łącze radiokomunikacyjne.
-
Samostabilizujące się algorytmy wierzchołkowego kolorowania grafów.
PublikacjaArtykuł jest poświęcony kolorowaniu grafów w modelu rozproszonym. Podano schemat konstruowania samostabilizujących się algorytmów wierzchołkowego kolorowania grafów z możliwością nadawania wierzchołkom priorytetów. W oparciu o tę technikę skonstruowano samostabilizujący się algorytm LF który został szczegółowo opisany. Przeprowadzono również testy komputerowe porównując algorytm LF ze znanymi wcześniej algorytmami samostabilizującymi.
-
Evaluation of inhibition of cancer cell proliferation in vitro with different berries and correlation with their antioxidant level by advanced analytical methods
PublikacjaW pracy opisano wyniki badań:- właściwości przeciwutleniających ekstraktów rozpuszczalnikowych (DMSO) uzyskanych z różnych gatunków owoców jagodowych- zdolność do infibizacji proliferacji komórek rakowych.W badaniach wykorzystano testy (DPPH) oraz zaawansowane techniki analityczne (spektroskopia FTIR oraz fluoroscencja 3D)Wyniki badań wskazują, że spożywanie owoców jagodowych może zredukować zagrożenie procesu proliferacji komórek...
-
ROZPROSZONY SYSTEM KOMUNIKACJI I NADZORU DLA MORSKIEGO ODDZIAŁU STRAŻY GRANICZNEJ – PROJEKT STRADAR
PublikacjaSystem STRADAR to wynik realizacji projektu, którego gestorem jest MO SG. Był on współfinansowany przez NCBiR. W artykule opisano system, przedstawiając ogólną koncepcję, architekturę, elementy funkcjonalne i realizację oprogramowania zainstalowanego w tych elementach. Krótko scharakteryzowano także testy, jakim poddano system, który na tym etapie – jako całość – osiągnął VII poziom gotowości technologii.
-
Preliminary Testing of the Influence of Modified Polycaprolactones on Anabaena Variabilis Growth in Seawater
PublikacjaSeveral new biodegradable polymer materials have recently come onto the global market. Mostly the results on degradation kinetic studies are presented. This paper suggests using one of the tests to estimate the impact of polymer packaging material on sea life. The microorganism chosen was Anabaena variabilis (identified in many waters, including those of the Baltic Sea, especially in the Gulf of Gdansk and Puck Bay; this cyanobacterium...