Filtry
wszystkich: 2233
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: acceptance of passing
-
ELECTRON-IMPACT IONIZATION CROSS SECTIONS CALCULATIONS FOR PURINE AND PYRIMIDINE MOLECULES
PublikacjaCross sections for electron-impact ionization of purine and pyrimidine molecules have been calculated using binary-encounter-Bethe method for electron energies ranging from the ionization threshold up to 5 keV. Ionization cross section for purine molecules is 1.4 times higher than for pyrimidine molecules. Acceptable agreement between experimental and theoretical ionization data for pyrimidine molecule has been found.
-
Modelling Signalised Intersections Reliability of Functioning
PublikacjaThe article addresses a fundamental aspect of traffic, i.e. the operation of traffic signals at intersections, in reference to the reliability theory. In many cases, when intersections carry substantial amounts of traffic, selecting control parameters to produce satisfactory traffic conditions is quite difficult. Design methods do not cover all possible situations which are the result of intersection geometry and location...
-
Calibration of permeation passive samplers with silicone membranes based onphysicochemical properties of the analytes. Anal. Chem.**2003 dostępny z Internetu http://pubs3.acs.org/acs/journals/, s. A-K, 6 rys. 7 tab. bib- liogr. 17 poz. Kalibracja permeacyjnych dozymetrów pasywnych z membraną silikonową w opar- ciu o fizykochemiczne właściwości analitów.
PublikacjaW pracy opisano sposób kalibracji pasywnych dozymetrów permeacyjnych, wyko-rzystywanych w badaniach powietrza w oparciu o własności fizykochemiczneanalitów. Stwierdzono silną zależność pomiędzy stałą kalibracyjną (K) dozy-metrów i liczbą atomów węgla w cząsteczce analitu (w obrębie danej grupyzwiązków chemicznych) dla alkoholi, alifatycznych i aromatycznych węglowodo-rów oraz estrów. Taka zależność występuje również pomiędzy...
-
Calculations of labyrinth seals with and without diagnostic extraction in fluid-flow machines
PublikacjaLabyrinth seals are essential components of steam turbine unit constructions. Two types of labyrinth seals can be named, the first of which is the seal without diagnostic steam extraction, and the second – with extraction. The distribution of flow parameters along the packing is affected remarkably by the average seal clearance. The presence of diagnostic extraction leads to the equation system which is determinable and can be...
-
CM Voltage Compensators for Power Electronic Interfaces
PublikacjaThe experimental results presented in the paper have shown that the application of the PEIs might cause EMC related problems, especially in the case of the application of a group of connected converters. The most convenient way to reduce EMI currents and prevent aggregation of EMI currents introduced by a group of converters is through passive compensation of voltage interference sources inside of the single converters. In the...
-
Increasing the lifetime of engineering structures through the use of composite laggings
PublikacjaThe use of composite laggings prevents concrete (chemical and biological) corrosion. Columns coated with composite or reinforced composite are more resistant to negative environmental impact on concrete or steel. The mechanical properties of the reinforced casing also cause that these types of columns are more resistant to lateral forces. The applied casing limits carbonization of concrete and cyclical freezing and thawing with...
-
Video DATA - Traffic generation modeling for discount shops - Rakoczego Street
Dane BadawczeThe data includes video traffic data (vehicles, pedestrians, cyclists) registered at 21 Rakoczego street in Gdansk. The data covers the day 01.10.2020 at 6:00-10:00. The video camera was installed niearby the parking area belonging to the discount store Lidl. The data obtained was used in analysis, providing information about the modal split and the...
-
Zarzadzanie ryzykiem jako wymiar strategicznego i przedsiębiorczego podejścia do zarządzania małym i srednim przedsiębiorstwem
PublikacjaJedną z wielu przyczyn niepowodzenia ekonomicznego małych i średnich przedsiębiorstw jest niezrozumienie lub niewłaściwe rozumienie kwestii zarządzania ryzykiem. Ryzyko w wielu wymiarach sprzężone jest z procesem przedsiębiorczym. Zarządzanie nim wymaga dostrzegania okazji, umiejętności wykorzystywania zagrożeń jako szans oraz dynamicznej odpowiedzi na zmiany w otoczeniu i w samej organizacji. Sposób podej- ścia do zarządzania...
-
Rozumieć Kanta całościowo czyli o Opus postumum Immanuela Kanta
PublikacjaTekst pokazuje fundamentalne znaczenie Opus postumum Kanta dla zrozumienia całości jego filozofii, dynamiki jej rozwoju, jej trudności i niekonsekwencji. Podstawowym problemem jest tu problem przejścia od metafizyki przyrody do fizyki. Omawiając pracę Tomasza Kupścia tekst pokazuje jak ważne w rozumieniu Kanta jest wyjście poza problematykę filozofii przyrody w stronę filozofii Boga, bo zwieńczenie filozofii transcendentalnej...
-
THE METHOD OF MEASURING THE MEMBRANE COVER GEOMETRY USING LASER SCANNING AND SYNCHRONOUS PHOTOGRAMMETRY
PublikacjaThe authors present the experience and results of field studies carried out at the technical acceptance of Forest Opera (name in Polish: Opera Leśna) in Sopot (Poland). An unusual design of covering made in the form of “Sheerfill I” technical fabric membrane required spanned in the form of sails, required the use of terrestrial laser scanning. Such approach allowed for the fast and accurate record of the surface of individual panels...
-
Leadership, culture, intellectual capital and knowledge processes for organizational innovativeness across industries: the case of Poland
PublikacjaPurpose – This study aims to present the overview of intellectual capital creation micro-mechanisms concerning formal and informal knowledge processes. The organizational culture, transformational leadership and innovativeness are also included in the investigation as ascendants and consequences of the focal relation of intellectual capital and knowledge processes. Design/methodology/approach – Based on a sample of 1,418 Polish...
-
Green Polymer Nanocomposites for Skin Tissue Engineering
PublikacjaFabrication of an appropriate skin scaffold needs to meet several standards related to the mechanical and biological properties. Fully natural/green scaffolds with acceptable biodegradability, biocompatibility, and physiological properties quite often suffer from poor mechanical properties. Therefore, for appropriate skin tissue engineering and to mimic the real functions, we need to use synthetic polymers and/or additives as complements...
-
LOKALIZACJA OBIEKTÓW BUDOWLANYCH W SĄSIEDZTWIE LINII 110 kV
PublikacjaW artykule omówiono wymagania przepisów w zakresie dopuszczalnych wartości pola elektrycznego i magnetycznego niskiej częstotliwości. Przedstawiono wyniki obliczeń rozkładu pola elektrycznego metodą ładunków stymulowanych i w programie FEMM dla przykładowej lokalizacji obiektu przemysłowego w sąsiedztwie linii 110 kV.
-
Computational issues of solving the 1D steady gradually varied flow equation
PublikacjaIn this paper a problem of multiple solutions of steady gradually varied flow equation in the form of the ordinary differential energy equation is discussed from the viewpoint of its numerical solution. Using the Lipschitz theorem dealing with the uniqueness of solution of an initial value problem for the ordinary differential equation it was shown that the steady gradually varied flow equation can have more than one solution....
-
Hybrid energy storage forelectric multiple units to operate at the partially electrified line Gdynia -Hel
PublikacjaThe article presents calculations enabling the selection of an on-board energy storage device to replace diesel-powered trains with modern storage multiple units on the example railway line Gdynia Główna -Hel. The pioneering and currently used storage electric multiple units, mainly in Europe, were presented. The condensed results of the inventory of the line in question, including the technical condition...
-
Modelling of cutting by means of fracture mechanics
PublikacjaThe suitability of modern fracture mechanic theory was proved for the estimation of the cutting force and the cutting specific resistance. This paper shows modification of Ernst-Merchant theory and its application for determination some other properties of wood sample. This theory is acceptable for evaluation of shear yield stresses and shear plane angle. Sawing by gang saw machine was used as a process similar to the orthogonal...
-
MODELLING OF CUTTING BY MEANS OF FRACTURE MECHANICS
PublikacjaThe suitability of modern fracture mechanic theory was proved for the estimation of the cutting force and the cutting specific resistance. This paper shows modification of Ernst-Merchant theory and its application for determination some other properties of wood sample. This theory is acceptable for evaluation of shear yield stresses and shear plane angle. Sawing by gang saw machine was used as a process similar to the orthogonal...
-
Analysis of magnetic field distribution inside ferromagnetic thin shells during degaussing process
PublikacjaAnalysis of the demagnetization of a large ferromagnetic object like a ship, was conducted. The approximate mathematical model in the form of a long cylindrical shell of constant magnetic permeability was applied. The discrete degaussing winding was assumed and the current density and magnetic flux density distribution in the ferromagnetic shell wall were determined. Based on the frequential and temporal analysis the recommended...
-
Sailing Vessel Routing Considering Safety Zone and Penalty Time for Altering Course
PublikacjaIn this paper we introduce new model for simulation sea vessel routing. Besides a vessel types (polar diagram) and weather forecast, travel security and the number of maneuvers are considered. Based on these data both the minimal travelling costs and the minimal processing time are found for different vessels and different routes. To test our model the applications SailingAssistance wad improved. The obtained results shows that...
-
Laboratory research on the influence of swelling clay on the quality of borehole cementing and evaluation of clay-cutting wellbore tool prototype
PublikacjaSwelling clay phenomenon is frequently observed during oil and gas drilling operations and has a significant impact on the quality of cementing procedure. Certain types of clayey minerals increase their volume in contact with water-based drilling fluids. After drilling is completed, borehole remains unsupported and filled with waterbased drilling fluids for several hours, before a casing string is inserted and secured with cement....
-
Signal conditioning for examination of shallow-water acoustic noise correlation properties
PublikacjaThe article describes the process of signal conditioning for examination of acoustic noise correlation properties in shallow water. Knowledge of these properties is very important for the design processes of passive and active hydroacoustic systems. This paper focuses on the above issue from the point of view of passive sonar. In sonar systems, signal processing algorithms operate on both useful acoustic signals, and accompanying...
-
ASSESSMENT of PERFORMANCE of UMV (2024)
Kursy Online(W) Assessment of Performance of Unmanned Maritime Vehicles (W-Lecture) - DAPE - WIMiO AP-of-UMV (W) -DAPE - WIMiO The course entitled "Assessment of Performance of Unmanned Maritime Vehicles (W-Lecture)" is conducted for the DAPE WIMiO Students. The AP-of-UMV (W) course is to discuss the following problems: - major areas of application of UMV unmanned maritime vehicles, - sea environment, - types of UMV vehicles, -...
-
Odpowiedzialność kierownicza w biznesie – zagadnienia procesowe i rodzajowe
PublikacjaCelem podjętych prac było przeprowadzenie rozważań nad zagadnieniami powstawania, ponoszenia, podejmowania oraz pociągania do odpowiedzialności kierowniczej. Kontynuacja badań nad odpowiedzialnością kierowniczą została oparta na sformułowanej wcześniej definicji. Umożliwiło to procesowe ujęcie przedmiotu eksploracji. W procesie tym wyróżniono fazy: przywołania, przyjęcia oraz poniesienia odpowiedzialności kierowniczej. Przeprowadzone...
-
Optimization of Automata
PublikacjaThis book is conceived as an effort to gather all algorithms and methods developed by the author of the book that concern three aspects of optimization of automata: incrementality, hashing and compression. Some related algorithms and methods are given as well when they are needed to complete the picture.
-
Evaluating the Internal and External Usability of Mobile Technologies in Facilitating Knowledge Transfer
PublikacjaA worker’s performance and productivity depend on a variety of factors including knowledge, to be essential for self-effectiveness and self-efficacy. In the literature, knowledge transfer is argued to enhance the quality of work, and therefore, its value. When addressing this issue, the latest studies have considered and evaluated the use of mobile technologies, which are evidenced to improve a worker’s capacity and skills. However,...
-
Validation study on a new semi-empirical method for the prediction of added resistance in waves of arbitrary heading in analyzing ship speed trial results
PublikacjaThis paper describes an open and extensive validation study carried out by the Specialist Committee on Ships in Operation at Sea (SOS) of the International Towing Tank Conference (ITTC) on the newly developed SHOPERA-NTUA-NTU-MARIC (SNNM) wave-added resistance prediction method. The SNNM method aims at a simple, fast and transparent determination of the added resistance in regular waves of arbitrary encounter directions, even when...
-
Mapping of the Covid-19 Vaccine Uptake Determinants From Mining Twitter Data
PublikacjaOpinion polls on vaccine uptake clearly show that Covid-19 vaccine hesitancy is increasing worldwide. Thus, reaching herd immunity not only depends on the efficacy of the vaccine itself, but also on overcoming this hesitancy of uptake in the population. In this study, we revealed the determinants regarding vaccination directly from people’s opinions on Twitter, based on the framework of the 6As taxonomy. Covid-19 vaccine acceptance...
-
Complementary green analytical procedure index (ComplexGAPI) and software
PublikacjaIt is not easy to find appropriate tools for the evaluation of the “green”nature of analytical methodologies which involve the use of compounds, materials, or chemicals manufactured prior to the analytical step. Here, we propose a new metric for the evaluation of analytical procedures based on the GAC attributes. The proposed solution expands on the well-known green analytical procedure index by adding additional fields pertaining...
-
Are creative users more apt in reusing and adopting Open Government Data (OGD)? Gender differences
PublikacjaOpen Government Data (OGD) has been considered as a potent instrument for value creation and innovation by a range of stakeholders. Given that individual ingenuity is a function of individual and environmental factors, it is important to understand how the OGD adoption and usage is a factor of creative performance behaviors (CPB), viz., Problem Identification (PI), Information Search (IS), Idea Generation (IG) and Idea Promotion...
-
Experimental and theoretical investigation of conformational states and noncovalent interactions in crystalline sulfonamides with a methoxyphenyl moiety
PublikacjaFour sulfonamide derivatives with a methoxyphenyl moiety, namely N-{4-[(2-methoxyphenyl)sulfamoyl] phenyl}acetamide (1a), N-{4-[(3-methoxyphenyl)sulfamoyl]phenyl}acetamide (1b), 4-amino-N-(2- methoxyphenyl)benzenesulfonamide (2a) and 4-amino-N-(3-methoxyphenyl)benzenesulfonamide (2b), have been synthesized and characterized physiochemically by CHNS, MS, FT-IR, 1H NMR, 13C NMR, PXRD and TG methods. Crystal structures were determined...
-
Zastosowanie techniki ściegu odpuszczającego do spawania mokrego
PublikacjaW artykule przedstawiono zastosowanie techniki ściegu odpuszczającego do poprawy właściwości złączy ze stali konstrukcyjnych wykonywanych w warunkach mokrego spawania pod wodą. Scharakteryzowano spawanie mokre elektrodami otulonymi zmiany struktury i właściwości złączy spawanych przez nakładanie ściegów odpuszczających. Przedstawiono metodykę oraz wyniki badań metalograficznych i twardości próbek ze stali konstrukcyjnej o podwyższonej...
-
Small Antenna Design Using Surrogate-Based Optimization
PublikacjaIn this work, design of small antennas using efficient numerical optimization is investigated. We exploit variable-fidelity electromagnetic (EM) simulations and the adaptively adjusted design specifications (AADS) technique. Combination of these methods allows us to simultaneously adjust multiple geometry parameters of the antenna structure of interest in a computationally feasible manner, leading to substantial reduction of the...
-
Hydrochar-nanoparticle integration for arsenic removal from wastewater: Challenges, possible solutions, and future horizon
PublikacjaArsenic (As) contamination poses a significant threat to human health, ecosystems, and agriculture, with levels ranging from 12 to 75% attributed to mine waste and stream sediments. This naturally element is abundant in Earth's crust and gets released into the environment through mining and rock processing, causing ≈363 million people to depend on As-contaminated groundwater. To combat this issue, introducing a sustainable hydrochar...
-
Analysis of activity of people using motion sensors
PublikacjaThe article presents the designed and implemented system for activity monitoring of people using passive motion sensors and methods for activity maps generation. In the paper he method is presented and results obtained for simulated data and for data from observations with the participation of people.
-
Prediction of ringing frequencies in DC-DC boost converter
PublikacjaIn the paper ringing phenomena in a DC-DC boost converter is presented. The ringing frequency is calculated using an analytical formula. The necessary wide band models of MOSFET transistor, passive and parasitics are described. The calculation results are verified in simulation and laboratory tests.
-
Hydrogen effects in duplex stainless steel welded joints - electrochemical studies
PublikacjaIn this work results on the influence of hydrogen on passivity and corrosion resistance of 2205 duplex stainless steel (DSS) welded joints are described. The results were discussed by taking into account three different areas on the welded joint: weld metal (WM), heat-affected zone (HAZ) and parent metal. The corrosion resistance was qualified with the polarization curves registered in a synthetic sea water. The conclusion is that,...
-
Voltage variations and their reduction in a rural low-voltage network with PV sources of energy
PublikacjaRenewable sources of energy (RES), especially photovoltaic (PV) micro-sources, are very popular in many countries. This way of clean power production is applied on a wide scale in Poland as well. The Polish legal regulations and tariffs specify that every prosumer in a low-voltage network may feed this network with a power not higher than the maximum declared consumed power. In power networks with RES, the voltage level changes...
-
Study on Microstructural Characterization, Mechanical Properties and Residual Stress of GTAW Dissimilar Joints of P91 and P22 Steels
PublikacjaThis article deals with the dissimilar joining of two different grade Cr-Mo steel (2.25Cr-1Mo: P22 and modified 9Cr-1Mo: P91) for power plant application. The dissimilar butt-welded joint was produced for conventional V groove design by using the gas tungsten arc welding (GTAW) process with the application of an ERNiCrMo-3 Ni-based super alloy filler. A microstructure characterization was performed to measure the inhomogeneity...
-
Analysis of circular polarization antenna design trade‐offs using low‐cost EM‐driven multiobjective optimization
PublikacjaCircular polarization (CP) antennas are vital components of modern communication systems. Their design involves handling several requirements such as low reflection and axial ratio (AR) within the frequency range of interest. Small size is an important criterion for antenna mobility which is normally achieved as a by‐product of performance‐oriented modifications of the structure topology. In this work, multiobjective optimization...
-
Creating IT competence centers
PublikacjaThis article indicates the need for supporting University Competence Centers. They are specialized centers, which aim to support teaching and development of newest software technologies, educating students, PhD Students and scientific workers also raising competetitiveness of the university at higher education market.
-
Recycling of Polyurethanes
PublikacjaPolyurethane waste can be recycled by mechanical methods (i.e., grinding and applying as a filler or pressing with a bonding agent) and chemical methods (mainly by e.g., glycolysis, hydrolysis, or aminolysis). There is also possibility to the recover energy from polyurethanes waste (by incineration, gasification, and pyrolysis).
-
Karol Grębowski dr inż.
OsobyKarol Grębowski (dr inż.) pracuje jako adiunkt w Katedrze Technicznych Podstaw Projektowania Architektonicznego na Wydziale Architektury Politechniki Gdańskiej. Jego badania naukowe dotyczą zjawisk szybkozmiennych zachodzących podczas drgań konstrukcji budowlanych, obiektów mostowych (trzęsienia ziemi) oraz badania w zakresie metodologii projektowania budynków stanowiących system ochrony pasywnej (SOP) odpornych na uderzenia pojazdów...
-
Computer-aided analysis of signals from a low-coherence Fabry-Perot interferometer used for measurements of biological samples
PublikacjaThe aim of the study was to develop an automated computer-aided system for analysis of spectrograms obtained from measurements of biological samples performed with a low-coherence Fabry-Pérot interferometer. Information necessary to determine dispersion characteristics of measured materials can be calculated from the positions of the maxima and minima that are present in their spectra. The main challenge faced during the development...
-
Video DATA - Traffic generation modeling for discount shops - Chrobrego Street
Dane BadawczeThe data includes video traffic data (vehicles, pedestrians, cyclists) registered at 75 Chrobrego street in Gdansk. The data covers the day 01.10.2020 at 6:00-22:00. The video camera was installed at the parking area belonging to the discount store Lidl. The data obtained was used in analysis, providing information about the modal split, the number...
-
Video DATA - Traffic generation modeling for discount shops - Czerska Street
Dane BadawczeThe data includes video traffic data (vehicles, pedestrians, cyclists) registered at 71 Czerska street in Gdansk. The data covers the day 01.10.2020 at 6:00-22:00. The video camera was installed at the parking area belonging to the discount store Lidl. The data obtained was used in analysis, providing information about the modal split, the number of...
-
Video DATA - Traffic generation modeling for discount shops - Gdanska Street
Dane BadawczeThe data includes video traffic data (vehicles, pedestrians, cyclists) registered at 21C Gdanska street in Gdansk. The data covers the day 01.10.2020 at 6:00-22:00. The video camera was installed at the parking area belonging to the discount store Lidl. The data obtained was used in analysis, providing information about the modal split, the number of...
-
Video DATA - Traffic generation modeling for discount shops - Dragana Street
Dane BadawczeThe data includes video traffic data (vehicles, pedestrians, cyclists) registered at 27 Dragana street in Gdansk. The data covers the day 01.10.2020 at 6:00-22:00. The video camera was installed at the parking area belonging to the discount store Lidl. The data obtained was used in analysis, providing information about the modal split, the number of...
-
Fuel systems of high power stationary engine
PublikacjaThe use of alternative fuels and, in the future, synthetic fuels has forced changes in the design of fuel supply systems in internal combustion engines. When operating a stationary engine at constant load, the possibility of using lean fuel mixtures appears. The selection of a precise operating mixture ignition system requires changes in traditional fuel systems. The article presents the current designs of fuel supply systems and...
-
3D Monitoring - Identification of measurement problems at larger movements of the tracked points
PublikacjaAuthors identified the problems associated with the determination of the controlled points coordinates by use of automated Total Station placed behind transparent barrier. Important thing in the mentioned analysis was a large change of controlled points position and not stable Total Station’s stand (because of stand’s thermal drift). This two elements, combined with measurement made through glass plate determine the need for impact...
-
Assessment of Subsoil Subsidence Under the Railway Surface with the Use of Fuzzy Sets
PublikacjaThe cause of the subsidence of the railway track is the subsidence of the track bed itself and it is often related to the subsidence of the subsoil. Such settlement leads to: uneven longitudinal railways and track twist. These phenomena have a negative impact on the comfort and safety of driving, and in extreme cases lead to a train derailment. It has been shown that the magnitude of these settlements is determined by many parameters...