Filters
total: 1711
filtered: 1582
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: POINT POSITIONING (PPP)
-
APPLICATION OF REDUNDANCY IN SHIP POWER PLANTS OF OFFSHORE VESSEL
PublicationPower and propulsion systems of offshore units must be of a very high level of reliability. The loss of ability to perform functions of their components causes generally to very high economic losses, which may be increased by unused the weather window resulting to postponing the planned offshore operations. To ensure carrying out so expensive offshore operations in the most reliable way, various types of redundancies are built-in...
-
Detection of debonding in adhesive joints using Lamb wave propagation
PublicationAdhesively bonded joints are widely used in many branches of industry. Mechanical degradation of this type of connections does not have significant symptoms that can be noticed during visual assessment, so non-destructive testing becomes a very important issue. The paper deals with experimental investigations of adhesively bonded steel plates with different defects. Five samples (an intact one and four with damages in the form...
-
Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearing
PublicationIn the present study, investigation of the effect of manufacturing errors on the performance of large tilting pad thrust bearings has been performed, following a CFD-based Thermohydrodynamic analysis of a single pad. A 3D model has been generated, including the pad, the lubricant film and the corresponding part of the collar. The pad has been assumed to be deformed about the pivot point, due to thrust loading. Manufacturing errors...
-
Comparative analysis of different numerical models of a steel radial gate
PublicationHydrotechnical structures are important components in water management system and general flooding safety. Their reliability should be ensured since potential damage might lead to catastrophic consequences. Weir gates are considered to be highly vulnerable elements of each hydro power plant, with regard to its dynamic resistance. The aim of the paper is to compare different numerical models and their influence on the results of...
-
Bimodal classification of English allophones employing acoustic speech signal and facial motion capture
PublicationA method for automatic transcription of English speech into International Phonetic Alphabet (IPA) system is developed and studied. The principal objective of the study is to evaluate to what extent the visual data related to lip reading can enhance recognition accuracy of the transcription of English consonantal and vocalic allophones. To this end, motion capture markers were placed on the faces of seven speakers to obtain lip...
-
Influence of sheet/purlin fasteners spacing on shear flexibility of the diaphragm
PublicationThe paper presents the influence of sheet/purlin fasteners location (in reference to trapezoidal profile cross section) on shear flexibility of the cladding acting as a diaphragm. Analytical procedures were presented and their limitations were discussed. Next, selected schemes of fasteners location, known from engineering practice, but not included in European codes and recommendations, were analysed numerically in order to observe...
-
Analysis of turnouts with non-linear curvature of diverging track for different train running speeds
PublicationThe paper deals with the issue of shaping a variable curvature in the diverging track of the railway turnout. Solution without a circular arc in the central zone, comprising two zones of non-linear curvature, of the same length, having zero curvature values at the end points, was adopted as a model, on the basis of the previously conducted dynamic tests. Optimum type of curvature was selected from the point of view of the kinematic...
-
The saga of a fish: from a survival guide to closing lemmas
PublicationIn the paper by D. Burago, S. Ivanov and A. Novikov, “A survival guide for feeble fish”, it has been shown that a fish with limited velocity can reach any point in the (possibly unbounded) ocean provided that the fluid velocity field is incompressible, bounded and has vanishing mean drift. This result extends some known global controllability theorems though being substantially nonconstructive. We give a fish a different recipe...
-
Billiard in a rotating half-plane
PublicationThe main objective of this research is to study the properties of a billiard system in an unbounded domain with moving boundary. We consider a system consisting of an infinite rod (a straight line) and a ball (a massless point) on the plane. The rod rotates uniformly around one of its points and experiences elastic collisions with the ball. We define a mathematical model for the dynamics of such a system and write down asymptotic...
-
A Finite Element Approach for Wave Propagation in Elastic Solids
PublicationThis book focuses on wave propagation phenomena in elastic solids modelled by the use of the finite element method. Although the latter is a well-established and popular numerical tool used by engineers and researchers all around the word the process of modelling of wave propagation can still be a challenge. The book introduces a reader to the problem by presenting a historical background and offering a broad perspective on the...
-
Collaborative planning? Not yet seen in Poland. Identifying procedural gaps in the planning system 2003–2023
PublicationCollaborative planning aims to increase the legitimacy of decision-making in spatial development. In this approach, planning involves debate and engagement in discourse, and participation and interaction between actors are thus at the heart of the planning process. This article examines whether the planning system in Poland as defined for the period 2003–2025 provides a level of participation and deliberation and other qualities...
-
Two-dimensional simulations of concrete fracture at aggregate level with cohesive elements based on X-ray lCT images
PublicationThe paper presents results of two-dimensional meso-scale simulations of fracture in notched concrete beams subjected to three-point bending test. Concrete was assumed as a 4-phase material composed of aggregate grains placed in the cement matrix, interfacial transitional zones (ITZs) and macro-voids. The particle distribution was taken from real concrete beams on the basis of X-ray lCT images. Comprehensive numerical analyses were carried...
-
Projekt badawczy BRIK: Opracowanie innowacyjnej metody wyznaczania precyzyjnej trajektorii pojazdu szynowego
PublicationW artykule przedstawiono podstawowe informacje dotyczące projektu badawczego realizowanego na zlecenie Narodowego Centrum Badań i Rozwoju oraz Spółki PKP Polskie Linie Kolejowe S. A. przez Konsorcjum Politechniki Gdańskiej i Uniwersytetu Morskiego w Gdyni. Projekt obejmuje wykorzystanie nowoczesnych metod pomiarowych, takich jak techniki pozycjonowania satelitarnego GNSS, pomiary inercyjne INS oraz skaning laserowy LS, w procesie...
-
Uncertainty Quantification of Additive Manufacturing Post-Fabrication Tuning of Resonator-Based Microwave Sensors
PublicationReconfigurability, especially in terms of the ability of adjusting the operating frequency, has become an important prerequisite in the design of modern microwave components and systems. It is also pertinent to microwave sensors developed for a variety of applications such as characterization of material properties of solids or liquids. This paper discusses uncertainty quantification of additive-manufacturing-based post-fabrication...
-
A Comprehensive Survey on Antennas On-Chip Based on Metamaterial, Metasurface, and Substrate Integrated Waveguide Principles for Millimeter-Waves and Terahertz Integrated Circuits and Systems
PublicationAntennas on-chip are a particular type of radiating elements valued for their small footprint. They are most commonly integrated in circuit boards to electromagnetically interface free space, which is necessary for wireless communications. Antennas on-chip radiate and receive electromagnetic (EM) energy as any conventional antennas, but what distinguishes them is their miniaturized size. This means they can be integrated inside...
-
Organizacja ruchu pociągów w obrębie stacji a oszczędność energii
PublicationW artykule przytoczono podstawowe zasady organizacji ruchu kolejowego. Wyodrębniono elementy sieci kolejowej oraz wskazano obszar stacji kolejowej jako najistotniejszy z punktu widzenia organi-zacji ruchu dla celów zmniejszenia zużycia energii trakcyjnej z uwzględnieniem rekuperowanej ener-gii. W dalszej części odwołano się do spotykanych w literaturze rozwiązań sterowania czasem posto-ju na stacji oraz sterowania czasem jazdy...
-
Etyczność działań w public relations - między amoralizmem a kazuistyką
PublicationArtykuł jest refleksją filozoficzną dotyczącą problemów moralnych public relations i dziennikarstwa. Autorka stawia w nim tezę, że dziennikarze i specjaliści public relations – wykonując profesje, których fundamentem jest informacja, komunikacja i zaufanie społeczne - współcześnie bardzo wiele swoich działań wyłączają ze sfery tych, które mogłyby być oceniane z punktu widzenia moralności. Uznają też, że ocenie etycznej można...
-
Architektura statków pasażerskich XX wieku.
PublicationArchitektura okrętów jako dyscyplina naukowa zajmuje się projektowaniem wnętrz oraz sylwet, jak również systematyką przestrzenną statków. Referat przedstawia rozwój architektury statków pasażerskich, które powstały w XX w. od momentu pojawienia się nowej dyscypliny naukowej – architektury okrętów, której prekursorami byli pracownicy Wydziału Architektury PG, aż do przełomu wieków XX i XXI. Statki pasażerskie ulegały przemianom,...
-
Job-related emotions and job burnout among civil servants: examining the shape of the relationship in cross-sectional and longitudinal models
PublicationWstęp: Związek pozytywności, czyli proporcji między pozytywnymi a negatywnymi emocjami, z wypaleniem zawodowym może przybierać kształt krzywoliniowy. Ponadto z perspektywy teoretycznej jest to relacja przyczynowo - skutkowa, w której pozytywność jest proksymalnym, a wypalenie – dystalnym wymiarem dobrostanu zawodowego. Dotychczasowe badania były jednak prowadzone najczęściej w planie poprzecznym i testowały relacje prostoliniowe....
-
Factors of successful client co-production in knowledge-intensive business services
PublicationPurpose This paper aims to explore the topic of client co-production in knowledge-intensive business services (KIBS). The paper first sketches a theoretical background and reviews previous studies on factors affecting successful client co-production in such companies and then examines these factors via case study research among a small KIBS company and its five customers. Design/methodology/approach The paper is based on an in-depth...
-
Linezolid-resistant Enterococcus faecium strains isolated from one hospital in Poland –commensals or hospital-adapted pathogens?
PublicationOne of the most pressing problems of enterococci infections is occurring resistance to linezolid, which is an antibiotic used in the treatment of infections caused by vancomycin-resistant strains (VRE). The main objective of our research was to investigate the relationship of 19 linezolid-resistant E. faecium isolates from 18 patients hospitalized at Clinical Hospital in Gdansk (Poland). One of the LZDREF was isolated in 2003...
-
Client co-production in knowledge-intensive business services (KIBS): Case study analysis
PublicationPurpose: This paper aims to explore the topic of client co-production in knowledge-intensive business services (KIBS). The paper first sketches a theoretical background and reviews previous studies on factors affecting successful client co-production in such companies and then examines these factors via case study research among a small KIBS company and its five customers. Methodology: The paper is based on an in-depth analysis...
-
Comparison of heat transfer characteristics in surface cooling using microjets with water, ethanol and HFE7100 as test fluids
PublicationAccurate control of cooling parameters is required in ever wider range of technical applications. It is known that reducing the dimensions of the size of nozzle leads to an increase in the economy of cooling and improves its quality. Present study describes research related to the design and construction of the nozzles and microjet study, which may be applied in many technical applications such as in metallurgy, electronics, etc....
-
Exploring perceptions of pro environmental educational mobile applications based on semantic field analysis
PublicationThe paper aims to identify multidimensional perceptions of mobile apps by their users. Special attention has been paid to pro-environmental educational apps. Semantic field analysis and measurement of emotional temperatures were performed to achieve this goal. Transcripts from seven focus group interviews were used as research material. The results indicate that functionality based on a reward or benefit system reinforces environmentally...
-
Present state and future of wetland technology in environmental protection in Poland
Publication: Polish experience with implementation and operation of constructed wetland systems are presented. Wetland technology can be applied for the removal of contaminants from aerial sources, point sources and for utilization of sewage sludge.From 1994-2002 monitoring of three different facilities for water protection was carried out. Substantial im-provement of water quality after implementation of the facilities was observed.From...
-
Influence of Different Biofuels on the Efficiency of Gas Turbine Cycles for Prosumer and Distributed Energy Power Plants
PublicationThe efficiency of a gas turbine can be affected by the use of different biofuels usually with a relatively Lower Heating Value (LHV). The paper evaluates the impact of calorific value of fuel on turbine performance and analyzes the possibilities of optimizing turbine construction from the point of view of maximum efficiency for a particular fuel. The several variants of design of small power microturbines dedicated to various biofuels...
-
Determination of Odor Intensity of Binary Gas Mixtures Using Perceptual Models and an Electronic Nose Combined with Fuzzy Logic
PublicationMeasurement and monitoring of air quality in terms of odor nuisance is an important problem. From a practical point of view, it would be most valuable to directly link the odor intensity with the results of analytical air monitoring. Such a solution is offered by electronic noses, which thanks to the possibility of holistic analysis of the gas sample, allow estimation of the odor intensity of the gas mixture. The biggest problem...
-
A Reduction Method for Bathymetric Datasets that Preserves True Coastal Water Geodata
PublicationWater areas occupy over 70 percent of the Earth’s surface and are constantly subject to research and analysis. Often, hydrographic remote sensors are used for such research, which allow for the collection of information on the shape of the water area bottom and the objects located on it. Information about the quality and reliability of the depth data is important, especially during coastal modelling. In-shore areas are liable...
-
Wyznaczenie obciążeń na poszycie okrętu wywołanych uderzeniem fal i uderzeniem w lód i ich wpływ na bezpieczeństwo okrętu
PublicationThe main problem is the vessels rather accurate determination of the hydrodynamic loads so-called hydroelasticity outside . This can be done by theoretical analysis , computer simulation or by experiment. This gives the hydrodynamic pressure distribution on the walls of the ship's hull and also on the walls of marine vessels .The most dangerous are the impact of extreme storm waves , the impact of the wharf and the impact zone...
-
Uncertainty in emotion recognition
PublicationPurpose–The purpose of this paper is to explore uncertainty inherent in emotion recognition technologiesand the consequences resulting from that phenomenon.Design/methodology/approach–The paper is a general overview of the concept; however, it is basedon a meta-analysis of multiple experimental and observational studies performed over the past couple of years.Findings–The mainfinding of the paper might be summarized as follows:...
-
Various cases of preservation and adaptive reuse Heritage Buildings in the Port of Gdynia
PublicationThe port of Gdynia contains a diverse range of heritage assets, starting with its spatial layout which is an urban concept designed in the first half of the 1920s. It is important to point out, this historically-shaped harbor space is preserved in its general idea and still functioning in port activities. Another significant element is the structural, technological solution which was the basis for constructing the entire port area...
-
Analysis of ring cracks in ceramic rolling elements using the boundary element method
PublicationCeramic materials have been increasingly used in bearing technology for over a dozen years. This is due to the characteristic properties of ceramic materials such as: high hardness, corrosion resistance, the possibility of use in aggressive chemical environments, as well as due to the lower specific weight compared to steel materials. However, the use of ceramic materials is connected with many limitations. The main disadvantages...
-
Impact of reclaimed asphalt pavement (RAP) on low-temperature properties of asphalt concrete
PublicationHot mix recycling is a practice which enables reusing materials from old asphalt pavements. Current Polish regulations allow usage of RAP only for binder and base courses, and its amount is limited. Asphalt mixtures with RAP material have to fulfil requirements stated for typical asphalt mixtures. The research presents low-temperature properties of twelve different asphalt concretes with RAP material, determined using three-point...
-
Enhanced photocatalytic activity of transparent carbon nanowall/TiO2 heterostructures
PublicationThe synthesis of novel tunable carbon-based nanostructure represented a pivotal point to enhance the efficiency of existing photocatalysts and to extend their applicability to a wider number of sustainable processes. In this letter, we describe a transparent photocatalytic heterostructure by growing boron-doped carbon nanowalls (B-CNWs) on quartz, followed by a simple TiO2 sol-gel deposition. The effect on the thickness and boron-doping...
-
Implementation of control system and tracking objects in a Quadcopter
PublicationIn this paper, we implement a quadcopter assembly with control and navigation module. The project also includes the design of the control panel for the operator which consists of a set of the micro-controller and the glove equipped with sensors and buttons. The panel has a touch screen which displays current parameters such as vehicle status, including information about orientation and geographical coordinates. The concept of quadcopter...
-
Architektura pomników poświęconych ofiarom ataków terrorystycznych jako kontynuacja realizacji komemoratywnych kształtowanych w postpamięci
Publicationarchitecture of Memorials Dedicated to the Victims of terrorist attacks as a continuation of commemorative Structures created within Post-memory Having the rich art of commemorating events of the Second World War as a key reference, this article will try to show how contemporary architectural interven- tions in public space make attempts to respond to the social need of dealing with traumatic events and formulating a new attitude...
-
Frequency-Based Regularization for Improved Reliability Optimization of Antenna Structures
PublicationThe paper proposes a modified formulation of antenna parameter tuning problem. The main ingredient of the presented approach is a frequency-based regularization. It allows for smoothening the functional landscape of the assumed cost function, defined to encode the prescribed design specifications. The regularization is implemented as a special penalty term complementing the primary objective and enforcing the alignment of the antenna...
-
Application of fracture mechanics for energetic effects predictions while wood sawing
PublicationIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (power) could be considered from a point of view of modern fracture mechanics. Cutting forces may be employed to determine not only toughness...
-
Chemical, thermal and laser processes in recycling of photovoltaic silicon solar cells and modules
PublicationIn recent years, photovoltaic power generation systems have been gaining unprecedented attention as an environmentally beneficial method to solve the energy problem. From the economic point of view the pure silicon, which can be recapture from the used cells, is the most important material due to its cost and shortage. In the paper selected methods of used or damaged module and cells recycling and experimental results are presented....
-
Testbed analysis of video and VoIP transsmission performance in IEEE 802.11 b/g/n networks
PublicationThe aim of the work is to analyze capabilities and limitations of different implementations of IEEE 802.11 technologies (IEEE 802.11 b/g/n), utilized for both video streaming and VoIP calls directed to mobile devices. Our preliminary research showed that results obtained with currently popular simulation tools can be drastically different than these possible in real-world environment, so, in order to correctly evaluate performance...
-
Genetic predisposition to inflammatory bowel disease
PublicationInflammatory bowel disease (IBD) is a chronic, incurable inflammatory disease of the digestive system. The two main disease entities included in the IBD are ulcerative colitis and Crohn's disease. According to epidemiological studies there are more and more new cases every year. In especially among the youngest patients with symptoms of malnutrition and growth inhibition to land up in hospitalwith cancer suspected. The purpose...
-
The Influence of the Chemical Composition of Selected Waste Materials from the Production of Copper on the Final Environmental Assessment
PublicationThis article presents qualitative and quantitative analysis of the waste produced by KGHM Polska Miedź. The waste has been analyzed according to its chemical composition and balanced in order to be reused and recycled. Special attention has been paid to mining industries producing the biggest amount of waste and ore enrichment businesses generating waste, which isn’t reused nowadays. Laboratory reseach has been conducted on floatation...
-
Analysis of Induced Voltages and Power Losses in High Voltage Power Cables for Selected Methods of Cables Sheaths Bonding
PublicationPower is increasingly supplied to city centres with 110 kV cable lines. This is a convenient way to supply power, and practically the only one possible in areas of dense urban development. A high-voltage cable contains a coaxial metallic sheath, in which in normal operation and in fault conditions (during short-circuits) significant line-to-earth voltages can be induced, which threatens electric shock and/or damage to the cable’s...
-
Integrate-and-fire models with an almost periodic input function
PublicationWe investigate leaky integrate-and-fire models (LIF models for short) driven by Stepanov and μ-almost periodic functions. Special attention is paid to the properties of the firing map and its displacement, which give information about the spiking behavior of the considered system. We provide conditions under which such maps are well-defined and are uniformly continuous. We show that the LIF models with Stepanov almost periodic...
-
Influence of vision measurement system spatial configuration on measurement uncertainty, based on the example of electric traction application
PublicationTechnical diagnostics plays a significant role in ensuring operational reliability of electrified rail transport. The most critical point in the transmission of electric energy to vehicles is the sliding contact of the current collector with the traction network. For this reason, work is currently being carried on new measuring methods, whose appliance allows for more complete diagnostics of the contact line and current collectors,...
-
Evaluation of Low Temperature Properties of Rubberized Asphalt Mixtures
PublicationThe paper presents low-temperature test results of asphalt mixtures designed with use of bitumen modified by crumb rubber and also SBS polymer. Laboratory tests were conducted on two types of asphalt mixtures for wearing course – stone matrix asphalt (SMA 8) and porous asphalt (PA 8). This paper presents results of the following laboratory tests at low temperatures: TSRST test, three point bending creep test, fracture toughness...
-
Potential of Polish R&D industry in the context of prototyping, design, development and control of a dedicated national satellite SAR system for marine ecosystem monitoring. Technical paper - preliminary study
Publicationpace technology is currently one of the most important elements in the advance of information societies and knowledge-based economies all over the world. The European Space Agency (ESA) is in the focal point of European space activities, while the European Union provides strong financial support for the development of space technologies and applications in its flagship programs. In a domestic scope, the Polish Space Agency (POLSA)...
-
Sensorless control of five-phase induction machine supplied by the VSI with output filter
PublicationIn this paper, a novel sensorless control structure based on multi-scalar variables is proposed. The tatic feedback control law is obtained by using the multi-scalar variables transformation, where the multi-scalar variables approach allows a full linearization of the nonlinear system. The control system could be described as “optimized” because of the minimized number of controllers. Furthermore, control system is divided into...
-
Estimation of fracture toughness and shear yield stress of orthotropic materials in cutting with rotating tools
PublicationThe cutting force is an energetic effect of splitting material, and might be considered from a point of view of modern fracture mechanics. Forecasting of the shear plane angle in cutting broaden possibilities for modelling of the cutting process even for thin uncut chips. Such mathematical model has been developed here for description of the orthotropic materials’ cutting on the base of fracture theory, and includes work of separation...
-
How to define and measure informal employment in CEE countries - the case of Poland
PublicationThe study of informal employment is still associated with several obstacles, from the scope of definition, through measurement methods, to policy recommendations. This article aims to revise the existing methodological frames in order to point out how to improve the study of informal employment in CEE countries. The case of Poland serves to examine whether the common definitions and measurement methods are suitable for an inclusive...