Search
Filters
total: 3428
filtered: 2380
displaying 1000 best results Help
Search results for: MEASUREMENTS
-
Performance of acicular grindable thermocouples for temperature measurements at sliding contacts
PublicationThe present study investigates the performance of acicular grindable thermocouples based on a constantan wire / steel hollow cylinder construction. The experiments showed that the measuring junction electrical resistance, temperature–voltage characteristic, measuring junction rise time and signal noise standard deviation of the acicular thermocouples are comparable to those of conventional J-type thermocouples with bare wire diameter...
-
Measurements of the optical and thermal properties of the 2D black phosphorus coating
PublicationBlack phosphorus is a 2D material, which properties are still being discovered. In this paper, the sensitivity to the temperature of a few-layer black phosphorus coating deposited, on the surface of a microsphere-based fiber-optic sensor, by a dip-coating method is presented. The coating was investigated after 2, 3, and 5 deposition cycles and during temperature growth from 50 °C to 300 °C in an interferometric setup. The intensity...
-
Channel Impulse Response Measurements at mmWave Band in Office and Conference Rooms
PublicationIn this paper, the measurements of the channel impulse response at mmWave band in office and conference rooms are described. The central frequency is 27 GHz with a bandwidth of 400 MHz. The description of the used measurement stand and considered environments are presented. The initial analysis of the power delay profile, mean delay, and RMS delay spread allows preliminary conclusions to be drawn that there is a significant impact...
-
Airborne and mobile laser scanning in measurements of sea cliffs on the southern Baltic
PublicationMeasurements of sea cliffs performed using periodic surveying based on laser scanning is currently one of the fastest and most accurate solutions. Supported with the technology of satellite measurements using GNSS (Global Navigation Satellite System) positioning and photographic measurements with the use of aerial vehicle, they enable an effective monitoring of the sea cliffs affected by the erosion. In case of the coast of southern...
-
The Use of Gravimetric Measurements to Determine the Orthometric Height of the Benchmark in the Port of Gdynia
PublicationThis paper contains a description of the technology used to make gravimetric measurements of the height of a reference point located in the Port of Gdynia, Poland. Measurements were made using a CG-5 gravimeter manufactured by LaCoste & Romberg Scintrex Inc., and determinations of position used a Leica Viva GS15 receiver integrated with a network of HxGN SmartNet GNSS reference stations. The measuring methodology required gravimeter...
-
Analysis of the possibilities in railways shape assessing using GNSS mobile measurements
PublicationIn recent years, a dynamic development of satellite positioning techniques using both static and mobile GNSS coordinates register mode can be observed. In addition, still developing Real-time GNSS Networks, post-processing algorithms and another measurement signal analysis algorithms, make the satellite measurements increasingly used in railway industry sector. In the article the possibilities which follows from the mobile satellite...
-
Multi-Taper-Based Automatic Correction of Non-Anechoic Antenna Measurements
PublicationPrototype measurements belong to the key steps in the development of antenna structures. Although accurate validation of their far-field performance can be realized in dedicated facilities, such as anechoic chambers, the high cost of their construction and maintenance might not be justified if the main goal of measurements is to support teaching or low-budget research. Instead, they can be performed in non-anechoic conditions and...
-
A telemedical and an outpatient thoracic impedance measurements - a validation algorithm of the electrodes placement
PublicationThis paper presents the algorithm for validation of electrodes locations for the thoracic impedance measurements. In particular the presented algorithm was designed to perform the telemetric sleep apnea monitoring. One of the problems, during the clinical tests of a developed device, was to preserve the repeatability of measurements. It strongly depended on the appropriate electrodes placement on the examined person’s thorax. It...
-
Determination of time delay between ventricles contraction using impedance measurements
PublicationThe paper presents a novel approach to assessment of ventricular dyssynchrony basing on multichannel electrical impedance measurements. Using a proper placement of electrodes, the sensitivity approach allows estimating time difference between chambers contraction from over determined nonlinear system of equations. The theoretical considerations which include Finite Element Method simulations were verified using measurements on...
-
The analysis of tram tracks geometrical layout based on Mobile Satellite Measurements
PublicationIn this article, the results of the research in a field of which uses active global navigation satellite system (GNSS) geodetic networks for the inventory of geodetic geometric tram tracks are presented. The applied measurement technique has been adapted for the designing of the geometric layout of tram tracks. Several configurations of receivers and settings of an active GNSS networks with the objective to increase the accuracy...
-
Underwater Navigation Ssystem Based on Doppler Shift – Measurements and Error Estimations
PublicationA new acoustic navigation system was developed to determine the position and speed of moving underwater objects such as divers and underwater vehicles. The path of an object and its speed were determined by the Doppler shifts of acoustic signals emitted by a transmitter placed on the object and received by four hydrophones installed at the periphery of the monitored body of water. The position and speed measurements were affected...
-
Noise measurements on low noise pavements - problems with inhomogeneity of wearing course
PublicationDuring the last several years, when performing numerous CPX noise measurements on low noise pavements,significant inhomogeneity of the wearing course was observed in numerous cases. Similar problems were almost not existing regarding to the dense pavements.In general three main reasons of inhomogeneity can be defined. The first one are imperfections in technology of production of a asphalt mix or/and errors made already during...
-
System setup and software for cyclic, staircase and square wave voltammetry measurements
PublicationHardware dedicated for electrochemical measurement sometimes does not allow performing certain voltammetry experiments. Staircase and square wave voltammetry, techniques which have many advantages comparing with standard voltammetric techniques, are rarely implemented in software controlling electrochemical measuring equipment. These methods, however, can be relatively easy realized with some addition...
-
Reliability of acicular grindable thermocouples for transient temperature measurements at sliding contacts
PublicationAcicular grindable thermocouples represent an interesting and prospective technique of temperature measurements at sliding contacts. This study aimed at the investigation of their reliability and accuracy as applied to the friction materials of various classes in contact with steel. The tests were conducted on a pin-on-disc tribometer under stationary and transient regimes. The experimental results were validated by comparing the...
-
Three electrode configuration measurements of electrolyte-diffusion barrier-cathode interface
PublicationMeasurements of a system consisting of cathode/doped ceria diffusion barrier/doped zirconia electrolyte were made using two- and three-electrode configuration. Results obtained on a three-electrode measurement configuration were compared with and reflect the results obtained in two-electrode configuration. Three-electrode measurements allowed separating the impact of the symmetrical interface in the investigated system. They also...
-
Dead-Time Effect Compensation Based on Additional Phase Current Measurements
PublicationThis paper proposes a new method of dead-time effect compensation. The proposed solution is based on additional phase current measurements realized by analog-to-digital converters. These measurements are carried out at the time instants specified by a pulsewidth-modulation (PWM) strategy. This makes it possible to estimate inverter currents at the commutation instants and, finally, to estimate the voltage error caused by dead time. This...
-
Measurements of High-Speed Data Transmission Radio Link for Special Applications
PublicationIn the article measurements of high-speed data transmission radio link for special applications were presented. Build measurement stand, measurement scenario and obtained results were briefly described. All conducted research work took place in real maritime environment.
-
Trust-Based Model for the Assessment of the Uncertainty of Measurements in Hybrid IoT Networks
PublicationThe aim of this paper is to introduce a NUT model (NUT: network-uncertainty-trust) that aids the decrease of the uncertainty of measurements in autonomous hybrid Internet of Things sensor networks. The problem of uncertainty in such networks is a consequence of various operating conditions and varied quality of measurement nodes, making statistical approach less successful. This paper presents a model for decreasing the uncertainty...
-
Performance Measurements of Real Time Video Transmission from Car Patrol
PublicationThe HSUPA technology application to video streaming from moving vehicle to the central server is presented in the paper. A dedicated software for transmission control in case of non public IP address is employed. Quality of video streaming in urban area was measured. Several car routes were investigated in the area of the Polish Tricity. Measurements pointed out that the real time streaming quality during vehicle movement is sufficient...
-
Representativity of ISO test track surface based on controlled pass-by measurements
PublicationWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on four ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance. This directive is based on the measurement procedures proscribed in the UNECE Reg.117. Measurements on 3 ISO tracks were performed in 2021 and presented at InterNoise 2022....
-
Low-Level Aerial Photogrammetry as a Source of Supplementary Data for ALS Measurements
PublicationThe development of laser scanning technology ALS allows to make high-resolution measurements for large areas result-ing in significant reduction of costs. The main stakeholders at heights data received from the airborne laser scanning is mainly state administration. The state institutions appear among projects such as ISOK. Each point is classified in ac-cordance with the standard LAS 1.2, our research focuses on the class 6 -...
-
Determining horizontal curvature of railway track axis in mobile satellite measurements
PublicationThe article discusses the applicability of a novel method to determine horizontal curvature of the railway track axis based on results of mobile satellite measurements. The method is based on inclination angle changes of a moving chord in the Cartesian coordinate system. In the presented case, the variant referred to as the method of two virtual chords is applied which consists in manoeuvring with only one GNSS (Global Navigation...
-
Radio Channel Measurements in Off-Body Communications in a Ferry Passenger Cabin
PublicationThis paper presents an off-body radio channel measurements in a ferry passenger cabin at 2.45 GHz band, for static sleeping scenarios with different body orientation and on-body antennas placements, and also for upper and lower sleeping berths. The measurements have been performed with two types of on-body wearable receiving antennas: FlexPIFA (flexible planar inverted F antenna), and FlexNotch (flexible adhesive-backed notch antenna)...
-
Recent total cross section measurements in electron scattering from molecules
PublicationThe grand-total cross sections (TCSs) for electron scattering from a range of molecules, measured over the period 2009-2019 in various laboratories, with the use of different electron transmission systems, are reviewed. Where necessary, the presented TCS data are also compared to earlier results. Collection of investigated molecular targets (biomolecules, biofuels, molecules of technological application,hydrocarbons) reflects their...
-
Signal Reconstruction from Sparse Measurements Using Compressive Sensing Technique
PublicationThe paper presents the possibility of applying a new class ofmathematical methods, known as Compressive Sensing (CS) for recovering thesignal from a small set of measured samples. CS allows the faithful recon-struction of the original signal back from fewer random measurements bymaking use of some non-linear reconstruction techniques. Since of all thesefeatures, CSfinds its applications especially in the areas where, sensing is...
-
Short and Long Term Measurements in Assessment of FRP Composite Footbridge Behavior
PublicationThe paper presents application of different sensors for the purpose of short and long term measurements, as well as a structural health monitoring (SHM) system to assess the behavior of a novel fiber reinforced plastics (FRP) composite footbridge. The aim is to present a thorough and concise description of these sensors networks and results gathered with their aid during in situ measurement of strains, displacements, and vibrations,...
-
Computer-aided evaluation of the railway track geometry on the basis of satellite measurements
PublicationIn recent years, all over the world there has been a period of intensive development of GNSS (Global Navigation Satellite Systems) measurement techniques and their extension for the purpose of their applications in the field of surveying and navigation. Moreover, in many countries a rising trend in the development of rail transportation systems has been noticed. In this paper, a method of railway track geometry assessment based...
-
Electron-scattering cross sections for selected alkyne molecules: Measurements and calculations
PublicationWe report cross-section results from experimental and theoretical studies on electron collisions with 1-butyne (HC≡C–CH2CH3) and acetylene (HC≡CH) molecules and from computations for a propyne (HC≡C–CH3) molecule. Absolute grand -total electron-scattering cross sections (TCSs) were measured at impact energies ranging from about 0.5 to 300 eV using the linear electron-transmission method. The TCS energy curve for 1-butyne has a...
-
Certification requirements for tram noise measurements in terms of today’s expectations in cities
Publication -
CFD ship squat determination method validation by GPS-RTK measurements
PublicationArtykuł zawiera porównanie numerycznych obliczeń osiadania statku z wynikami badań rzeczywistych z wykorzystaniem metody GPS-RTK.
-
High accuracy multisensor hydroacoustic system for models of trawl geometry measurements
PublicationW pracy przedstawiono wieloelementowy hydroakustyczny system do pomiaru modeli włoków. System został zaprojektowany dla Akademii Rolniczej w Szczecinie i umożliwia precyzyjny pomiar geometrii projektowanych tam narzędzi połowowych w tym selektywnych worków dorszowych. Zastosowanie małych hydrofonów o wysokiej częstotliwości pracy oraz cyfrowego przetwarzania sygnałów z analizą korelacyjną umożliwiło uzyskanie bardzo dużej dokładności...
-
Low-Level Aerial Photogrammetry as a Source of Supplementary Data for ALS Measurements
Publication -
Wear measurements of self-lubricating bearing materials in small oscillatory movement
Publication -
Outdoor I-V measurements of air-cooled silicon solar cell
PublicationStosując radiator aluminiowy i przpływ powietrza z obu stron krystalicznego krzemowego ogniwa słonecznego osiągnięto skuteczne odprowadzanie ciepła i schłodzenie do temperatury otoczenia. Nową metodą (przy oświetleniu ogniwa i mniejszym napięciu) wyznaczono rezystancję szeregową i współczynnik nieidealności mierzonej charakterystyki I-V.
-
Wear measurements of self lubricating bearing materials in small oscillatory movement
PublicationRosnące wymagania ekologiczne powodują wzrost tendencji wymiany klasycznych materiałów łożyskowych, wymagających dodatkowego czynnika smarnego, na materiały nie wymagające smarowania. Zamianie takiej może towarzyszyć obniżenie trwałości zmodernizowanego łożyska. Ten niekorzystny efekt nierzadko obserwuje się w węzłach łożyskowych kierownic turbin wodnych. Autorzy podjęli próbę wyjaśnienia zjawisk występujących w tego typu łożyskach....
-
Reduction of Influence of the High-Frequency Noise on the Results of Surface Topography Measurements
Publication -
The effect of valley depth on areal form removal in surface topography measurements
Publication -
Evaluation of precipitation measurements obtained from different types of rain gauges
Publication -
Determining horizontal curvature of railway track axis in mobile satellite measurements
Publication -
Reliability of UAVs in Fire Services Operations. Tests and Measurements of Selected Parameters
Publication -
Cross sections for electron scattering from furan molecules; measurements and calculations
PublicationZmierzono i policzono przekroje czynne (TCS) na rozproszenie elektronów na drobinach furanu (C4H4O). Całkowite przekroje czynne zmierzono metodą transmisyjną w zakresie energii 0.6 - 400 eV. Sprężysty i jonizacyjny przekrój czyny obliczono dla energii zderzenia do 4 keV; powyżej 70 eV suma obu przekrojów pozostaje w dobrej zgodności z mierzonymi wartościami TCS.
-
Virtual Models of Analog-Digital Converters in Education of Electrical Measurements and Instrumentation.
PublicationPrzedstawiono opracowane przez autorów przyrządy wirtualne do demonstracji działania przetworników analogowo-cyfrowych: integracyjnego, kompensacyjnego, sigma-delta, z pośrednim sygnałem częstotliwościowym. Programy umożliwiają obserwację zmian napięcia w punktach charakterystycznych układów w spowolnionej skali czasowej. Możliwe jest również zadawanie zakłóceń.
-
Measurements of surface roughness of heads of human hip joints in lubrication aspects
PublicationW niniejszej pracy przedstawiono wyniki pomiarów chropowatości chrząstki stawowej na powierzchniach głów kostnych stawu biodrowego człowieka. Pomiarów dokonano przy pomocy czujników mechanicznych i laserowych. Praca zawiera wyniki analizy statystycznej.
-
Evaluation of reinforcement corrosion rate in concrete structures by electrochemical noise measurements
PublicationW pracy przedstawiono wyniki obliczeń rezystancji polaryzacyjnej w układzie złożonym z dwóch elektrod (ze stali węglowej oraz elektrody odniesienia), umieszczonych w otulinie betonowej. Szybkość korozji ulega zmianom uzależnionym od stopnia nasiąknięcia betonu roztworem zawierającym jony chlorkowe. Zmiany rezystancji polaryzacyjnej elektrody stalowej oceniane są na podstawie pomiarów prądowego i potencjałowego szumu elektrochemicznego....
-
Practical Approach to IP Scheduled Throughput Measurements in Dual Connectivity Systems
PublicationIP scheduled throughput defined according to 3GPP TS 36.314 reflects user throughput regardless of traffic characteristics, and therefore has become one of the most important indicators for monitoring Quality of Service (QoS) of the end user in Evolved Universal Terrestrial Radio Access Network (E-UTRAN). However, networks built on a distributed architecture make the above definition impossible to be applied directly due to the...
-
Electron scattering from hexafluoroacetone molecules: cross section measurements and calculations
PublicationZmierzono absolutne całkowite przekroje czynne na zderzenie elektronów z drobinami hexafluoroacetonu (HFA). Pomiary przeprowadzono dla energii zderzenia od 1 do 400 eV. Zależność energetyczna przekroju czynnego wykazała obecność struktur związanych z procesami o charakterze rezonansowym. Wykonano obliczenia sprężystego i jonizacyjnego przekroju czynnego dla drobin HFA i acetonu. Suma obliczonych przekrojów wykazuje dużą zgodność...
-
Fiber-optic Fabry-Pérot sensors – modeling versus measurements results
PublicationThis paper describes how parameters of investigated substances and the fiber-optic Fabry-Pérot sensing interferometer affect the spectrum of the optical radiation at the output of the sensor. First, the modeling of the operation of the sensing interferometer was conducted. Most important parameters and effects that were taken into account are: dependences of the refractive indices of the core and the cladding, as well the mode...
-
Implementation of constant component filter in measurements of random telegraph signal noise
PublicationNoise is generated in all semiconductor devices. The intensity of these fluctuations depends on used elements, manufacturing process, operating conditions and device type. The result noise is a superposition of different kinds of fluctuations like thermal noise, generation-recombination noise, 1/f noise, shot noise and Random Telegraph Signal (RTS) noise. The last one, RTS noise is observed as nonstationary impulse fluctuations....
-
Intercomparison on measurements of PCBs in pork fat during the Belgian PCB-crisis
PublicationW pracy przedstawiono wyniki porównania międzylaboratoryjnego oznaczania PCB w tłuszczu wieprzowym. Porównanie międzylaboratoryjne przeprowadzono w związku z tzw. "belgijskim kryzysem PCB" w latach 1999-2000. W porównaniu uczestniczyło 31 laboratoriów. Materiałem do badań były wyprodukowane w Instytucie Metod i Pomiarów Odniesienia (IRMM) w Geel - Belgia, trzy materiały odniesienia zawierające PCB w tłuszczu wieprzowym (suma PCB...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements Dataset
PublicationThe dataset titled EH36 steel for shipbuilding (plate thickness 50 mm) – CMOD – force record, a0/W=0.6 contains a CMOD (Crack Mouth Opening Displacement) – Force record which is the base for evaluation of the fracture toughness of structural steel. Bend specimens with a Bx2B section (B = 50 mm), and relative initial crack length a0/W=0.60 were used. The test was carried out at ambient temperature in accordance with the ISO 12135...