Filters
total: 590
Search results for: COEFFICIENT OF DETERMINATION
-
A New Direct-Sequence Spread Spectrum Signal Detection Method for Underwater Acoustic Communications in Shallow-Water Channel
PublicationDirect-Sequence Spread Spectrum (DSSS) is one of the modulation and coding techniques used in Underwater Acoustic Communication (UAC) systems for reliable data transmision even at low signal levels. However, in a shallow water channel, there is a strong multipath propagation which causes a phase fluctuation of the received signal, affecting the performance of the spread-spectrum system. The article presents a differential method...
-
Comparison of various flow maldistribution quantification methods in mini heat exchangers
PublicationThe aim of study is to compare various flow maldistribution quantification methods, using velocity, mass flow rate, pressure, and temperature. An experimentally validated numerical study has been prepared and a heat exchanger with 34 semi-circular channels with a diameter of 3.1 mm has been tested. The minichannels were heated from the bottom with a heat flux of 50, 60, 70, and 80 kW/m2. The cases for various inlet velocities of...
-
Stability of truss with side - supports. The case of linear and rotational elastic supports
PublicationThe research is devoted to study lateral buckling of truss with linear and rotational elastic side-supports. Geometrically nonlinear analysis of example truss with linear and rotational elastic sidesupports is carried out. The limit normal force in compressed chord of the truss due to stiffness of side supports is calculated. The elastic support reaction in relation to force in compressed chordand coefficient of buckling length...
-
Theoretical study of thermofrictional oscillations due to negative friction-temperature characteristic
PublicationAnalytical study on oscillations of a body on a moving counterbody has been done by assuming imperfect frictional thermal contact and friction that decreases with contact temperature. It has been shown that stick-slip oscillation occurs due to decrease of friction coefficient when the body moves in the opposite direction to the counterbody. Dynamical characteristics, such as conditions for stable sliding and limit cycles, have...
-
Study of the influence of thermal factors on the welding process of polyethylene gas pipelines,
PublicationA one-dimensional calculation scheme is proposed with the help of which it is possible to determine and set the technological parameters with the accuracy to be realized in production conditions: the temperature of the heating element and the heating time, which allows maximum mechanization of the technological operations of polyethylene gas pipelines welding. The numerical value of the coefficient of temperature for polyethylene...
-
The shape of an ROC curve in the evaluation of credit scoring models
PublicationThe AUC, i.e. the area under the receiver operating characteristic (ROC) curve, or its scaled version, the Gini coefficient, are the standard measures of the discriminatory power of credit scoring. Using binormal ROC curve models, we show how the shape of the curves affects the economic benefits of using scoring models with the same AUC. Based on the results, we propose that the shape parameter of the fitted ROC curve is reported...
-
Poly(hydroxybutyrate-co-hydroxyvalerate) as a biodegradable binder in a negative electrode material for lithium-ion batteries
PublicationIn this work, graphite-based negative electrode for lithium-ion battery consisting a novel and biodegradable binder poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) is compared with standard graphite electrode with polyvinylidene fluoride (PVDF) as a binder. The rate and cycling performance of lithium ion insertion/extraction of electrodes with PHBV in a half-cell configuration are evaluated. Moreover, on the basis of the electrochemical...
-
A prototype of electrochemical sensor for measurement of carbonyl compounds in air
PublicationThe paper presents the results of investigation on a prototype sensor for measurement of benzaldehyde and formaldehyde in air. Sensitivity, limit of quantification and coefficient of selectivity of the sensor have been determined as a function of membrane thickness and electrode type using square wave voltammetry (SWV) technique. The working and counter electrodes were made of platinum and gold. Ionic liquids 1-hexyl, 3-methylimidazolium...
-
Experimental investigations on condensation in flow of HFE-7100 in small diameter channels
PublicationIn the paper the authors present investigations of flow condensation with the use of the HFE-7100 as a working fluid. The original and new approach to removing the heat from the channel was applied. The research was carried out using a wide-range real time observations, e.g. using infrared camera and stroboscope microphotography. This paper presents the details of experiment as well as the influence of heat and flow parameters...
-
Reduction of Derivative pipeline effort in water turbine
PublicationThe paper presents an approach to evaluate and reduce the effort of the derivative pipeline in a water turbine of a hydrostatic power station in its vulnerable spots. Potential places of the biggest effort of the structure, as well as the coefficient of displacement and safety factor related to them were identified using FEM numerical method. Pipeline reinforcement was designed and made based on FEM analysis. Original technology...
-
The properties of reduced Ge-Sb-O glasses for thermoelectric devices
PublicationThe structural and electrical properties of germanium-antimonate glasses after heat treatment in hydrogen have been determined. In the case of 50GeO2-50Sb2O3 glass reduced at 340°C even for less than 1 hour a continuous layer of antimony granules is formed and its electrical properties determine the surface conductivity of the reduced sample. The bulk electrical conductivity at 100°C of this sample was determined as 1000 Scm-1...
-
The impact of air humidity on the operation of proton exchange membrane fuel cells determined using dynamic electrochemical impedance spectroscopy
PublicationThis paper describes the changes in the fuel cell impedance across a range of current loads and humidity changes. The changes of each equivalent circuit parameters representing specific processes occurring in fuel cells, as a function of humidity and current changes, were determined. Within the combined scope of current and humidity, the optimal working conditions of the cells were determined, corresponding to the lowest impedance...
-
Effect of composition on the thermal properties and structure of M-Al-Si-O-N glasses, M = Na, Mg, Ca
PublicationThe primary objective of this study is to explore the relationship between the composition, structure, and thermal characteristics of M-Al-Si-O-N glasses, with M representing sodium (Na), magnesium (Mg), or calcium (Ca). The glasses were prepared by melting in a quartz crucible at 1650 °C and AlN precursor (powder) was utilized as a nitrogen source. The measured thermal properties studied were glass transition temperature (Tg),...
-
Vibrational Quenching of Optically Pumped Carbon Dimer Anions
PublicationCareful control of quantum states is a gateway to research in many areas of science such as quantum information, quantum-controlled chemistry, and astrophysical processes. Precise optical control of molecular ions remains a challenge due to the scarcity of suitable level schemes, and direct laser cooling has not yet been achieved for either positive or negative molecular ions. Using a cryogenic wire trap, we show how the internal...
-
Heave Plates with Holes for Floating Offshore Wind Turbines
PublicationThe paper presents an innovative solution which is heave plates with holes. The long-known heave plates are designed to damp the heave motion of platforms. They are most often used for Spar platforms. The growing interest in this type of platform as supporting structures for offshore wind turbines makes it necessary to look for new solutions. Based on the available literature and the authors’ own research, it was concluded that...
-
Comparison of heat transfer characteristics in surface cooling using microjets with water, ethanol and HFE7100 as test fluids
PublicationAccurate control of cooling parameters is required in ever wider range of technical applications. It is known that reducing the dimensions of the size of nozzle leads to an increase in the economy of cooling and improves its quality. Present study describes research related to the design and construction of the nozzles and microjet study, which may be applied in many technical applications such as in metallurgy, electronics, etc....
-
Testing of Software for the Planning of a Linear Object GNSS Measurement Campaign under Simulated Conditions
PublicationThe precision of a linear object measurement using satellite techniques is determined by the number and the relative position of the visible satellites by the receiver. The status of the visible constellation is described by DOP. The obtained geometric coefficient values are dependent on many variables. When determining these values, field obstacles at the receiver location and satellite positions changing with time must be taken...
-
Multi-layered tissue head phantoms for noninvasive optical diagnostics
PublicationExtensive research in the area of optical sensing for medical diagnostics requires development of tissue phantoms with optical properties similar to those of living human tissues. Development and improvement of in vivo optical measurement systems requires the use of stable tissue phantoms with known characteristics, which are mainly used for calibration of such systems and testing their performance over time. Optical and mechanical...
-
Pool boiling of nanofluids on rough and porous coated tubes: experimental and correlation
PublicationThe paper deals with pool boiling of water-Al2O3 and water- Cu nanofluids on rough and porous coated horizontal tubes. Commercially available stainless steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate the test heater. The tube surface was roughed with emery paper 360 or polished with abrasive compound. Aluminium porous coatings of 0.15 mm thick with porosity of about 40% were produced by...
-
Design and experimental investigations of a cylindrical microjet heat exchanger for waste heat recovery systems
PublicationCompact heat exchangers have more and more applications in many areas, including the HVAC, food and petrochemical industry. This paper describes the development of heat exchanger technology for waste heat recovery (WHR) from a range of processes. Case-study testing shows that the proposed heat exchanger can successfully enhance heat transfer and recover waste heat in a range of applications making them economically, environmentally and...
-
Iridium 5d -electron driven superconductivity in ThIr3
PublicationA polycrystalline sample of superconducting ThI r 3 was obtained by arc-melting Th and Ir metals. Powder x-ray diffraction revealed that the compound crystalizes in a rhombohedral crystal structure (R-3m, s.g. #166) with the lattice parameters: a = 5.3394 ( 1 ) Å and c = 26.4228 ( 8 ) Å . Normal and superconducting states were studied by magnetic susceptibility, electrical resistivity, and heat capacity measurements. The results...
-
Thermal and economic investigation of straight and U-bend double tube heat exchanger with coiled wire turbulator
PublicationExperimental research has been carried out for four individual heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend and U-bend with turbulator. Tests were made for the water-water system. The study covered a wide measuring range, i.e., Re = 800–9000 – on the shell side, for a constant cold water temperature of 9 ◦C and hot water of 50 ◦C. The heat exchangers were made from copper tubes with...
-
1D Model Callibration on the Basis on 3D calculations for Tesla Turbine
PublicationThe paper presents the system of equations for axisymmetriclaminar flow, after averaging, through the width of interdisk slit ofTesla turbine. Coefficients were introduced, as a result ofaveraging, that improve the efficiency of 1D model. The minimalnumber of such coefficients was determined. The 1D modelmakes it possible to attain analytical solutions to an accuracylimited by these coefficients. Calibration of 1D model depends...
-
High order of nongeminate recombination in organic bulk heterojunction solar cells
PublicationWe analyze high order of nongeminate recombination in organic donor–acceptor bulk heterojunction solar cells. The model of recombination where an exciton annihilates on an electron–hole Langevin bound pair near donor–acceptor interface has been applied in our studies. We obtained satisfactory agreement between experimental results and theoretical calculations for the concentration dependences of several parameters characterizing...
-
Optical properties of boron-doped nanocrystalline diamond films studied by spectroscopic ellipsometry
PublicationThe optical properties of boron-doped nanocrystalline diamond films, coated using Microwave Plasma Enhanced Chemical Vapour Deposition (μPE CVD) system, were analyzed by spectroscopic ellipsometry. Diamond films were deposited on silicon substrates. The ellipsometry data (refractive index (n(λ)), extinction coefficient (k(λ)) were modeled using dedicated software. Evolution of the optical structure with boron doping was observed...
-
Elliptical slot UWB monopole antenna
PublicationThe UWB monopole antenna with elliptical radiating slot end and microstrip feeding line terminated with radial stub have been designed, fabricated and measured. The antenna show return loss less than -12 dB in the whole UWB bandwidth. Linearity of the reflection coefficient phase product have also been achieved. Radiation patterns of the antenna measured at three selected frequency points indicated regular, approximately omni directional...
-
Self-Optimizing Adaptive Vibration Controller
PublicationThis paper presents a new approach to rejection of sinusoidal disturbances acting at the output of a discrete-time linear stable plant with unknown dynamics. It is assumed that the frequency of the sinusoidal disturbance is known, and that the output signal is contaminated with wideband measurement noise. The proposed controller, called SONIC (self-optimizing narrowband interference canceller), combines the coefficient fixing technique,...
-
High temperature monoclinic-to-tetragonal phase transition in magnesium doped lanthanum ortho-niobate
PublicationMagnesium doped lanthanum ortho-niobate (La0.98Mg0.02NbO4) was prepared by the molten salt synthesis method. X-ray diffraction and dilatometry methods were used to study high temperature behavior of the ceramic material. Special attention was paid to the phase transition between the monoclinic and tetragonal phases. The values of spontaneous strain on the basis of unit cell parameter, obtained by Rietveld refinement, have been...
-
Application of Headspace Solid-phase Microextraction with Poly(1-vinyl-3- Hexylimidazolium Chloride) Polymeric Ionic Liquid Coating using GC - MS to Determine Volatile Fatty Acids in Dairy Wastewater
PublicationVolatile fatty acids were determined in this study using headspace solid-phase microextraction (HS-SPME) with a poly(1-vinyl-3-hexylimidazolium chloride) polymeric ionic liquid coated fiber followed by gas chromatography - mass spectrometry. Experimental parameters such as extraction time and temperature, sample volume as well as desorption time and temperature were optimized. Detection limits of the method were in the range of...
-
Sensitivity analysis of simple random beam models by means of Monte Carlo Methods using Variance Reductions Techniques
PublicationA probabilistic sensitivity analysis of two nonlinear bar structures is presented. The analysis is carried out on the basis of the Monte Carlo method. The imperfections of the structures and the applied loads are adapted as random variables. Based on all of the generated input variables, an output response of the system is sought. Afterwards, a coefficient responsible for the structure failure is calculated and the limit state...
-
Analysis of Ceramic Elements with Ring-Crack Defects in Lubricated Rolling Contact
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. Surface ring cracks on lubricating rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations...
-
Structural and dynamic properties of water within the solvation layer around various conformations of the glycine-based polypeptide
PublicationSeveral conformations of the solvated glycine-based polypeptides were investigated using molecular dynamics simulations. Some properties of water in the neighbouring space around these molecules were investigated. It was found, that water forms a well-defined layer - the first solvation shell - around the peptide molecule, and thickness of this layer is independent of the peptide structure, and it equals to approximately 0.28 nm....
-
The effect of aeration mode (intermittent vs. continuous) on nutrient removal and greenhouse gas emissions in the wastewater treatment plant of Corleone (Italy)
PublicationThe paper reports the results of an experimental study aimed at comparing two configurations of a full-scale wastewater treatment plant (WWTP): conventional activated sludge (CAS) and oxic-settling-anaerobic process (OSA) with intermittent aeration (IA). A comprehensive monitoring campaign was carried out to assess multiple parameters for comparing the two configurations: carbon and nutrient removal, greenhouse gas emissions, respirometric...
-
Influence of iron content on water uptake and charge transport in BaCe0.6Zr0.2Y0.2−xFexO3−δ triple-conducting oxides
PublicationIn this work, we studied the BaCe0.6Zr0.2Y0.2−xFexO3−δ system which belongs to the triple-conducting oxides (TCOs) group. The electrochemical properties of BaCe0.6Zr0.2Y0.2−xFexO3−δ were investigated using electrochemical impedance spectroscopy (EIS) and the water uptake was analyzed using thermogravimetry (TG). All investigated materials exhibited water uptake, with proton concentration increasing with decreasing iron content....
-
Losses and energy efficiency of drive motors and systems
PublicationLosses and energy efficiency of every drive motor must be presented as functions of physical quantities independent of losses in the motor. Such quantities are speed and load required by the machine or device driven by the motor, changing in the drive operating field. Speed and load of the motor decide of the instantaneous useful power of the motor and also in a differentiated way of kinds and values of losses occurring in the...
-
Losses and energy efficiency of drive motors and systems
PublicationLosses and energy efficiency of every drive motor must be presented as functions of physical quantities independent of losses in the motor. Such quantities are speed and load required by the machine or device driven by the motor, changing in the drive operating field. Speed and load of the motor decide of the instantaneous useful power of the motor and also in a differentiated way of kinds and values of losses occurring in the...
-
Modeling of pharmaceuticals mixtures toxicity with deviation ratio and best-fit functions models
PublicationThe present study deals with assessment of ecotoxicological parameters of 9 drugs (diclofenac (sodium salt), oxytetracycline hydrochloride, fluoxetine hydrochloride, chloramphenicol, ketoprofen, progesterone, estrone, androstenedione and gemfibrozil), present in the environmental compartments at specific concentration levels, and theirmutual combinations by couples against Microtox® and XenoScreen YES/YAS® bioassays. As the quantitative...
-
Mitigation of the Flow Maldistribution in Minichannel and Minigap Heat Exchangers by Introducing Threshold in the Manifolds
PublicationIn the present paper, a detailed numerical investigation has been carried out to analyze the flow maldistribution in 50 parallel rectangular cross-section (1 mm depth and 1 mm width) minichannels and minigap section (1 mm depth and 99 mm width) with rectangular/trapezoidal manifolds in Z-type flow configuration. The author carried out numerical investigation with various mass flowrates, namely 0.05 kg/s, 0.1 kg/s and 0.2 kg/s which...
-
Labour share and income inequalities in the European Union, taking into account the level of development of economies
Publicationesearch background: The relationship between labour share and income inequality is a complex and multifaceted problem. Despite ongoing discussions among economists, there is still no consensus on the direction of the relationship between labour share and income ine-quality. Purpose of the article: The article aims to assess the impact of labour share on income inequal-ity, which is measured in three ways: the Gini index...
-
Probability distribution of flicker noise in AuNPdecorated graphene–Si Schottky barrier diode
PublicationWe present results of the probability distribution analysis of flicker noise generated in Au nanoparticle (AuNP) decorated graphene–Si Schottky barrier diodes with and without yellow light illumination (592 nm), close to the localized surface plasmon resonance in the AuNPs (586 nm). The AuNPs occupy imperfections in the single-layer graphene and reduce the flicker noise intensity generated in the graphene layer. The estimated probability...
-
Automated detection of sleep apnea and hypopnea events based on robust airflow envelope tracking
PublicationThe paper presents a new approach to detection of apnea/hypopnea events, in the presence of artifacts and breathing irregularities, from a single-channel airflow record. The proposed algorithm identifies segments of signal affected by a high amplitude modulation corresponding to apnea/hypopnea events. It is shown that a robust airflow envelope—free of breathing artifacts—improves effectiveness of the diagnostic process and allows...
-
Magnetic properties of ferromagnetic Pu2Pt3Si5
PublicationThe structural, magnetic, and thermodynamic properties of a new plutonium based compound, Pu2Pt3Si5, are reported. Single crystals produced by a Sn-flux technique have been analyzed showing a ferromagnetic behavior at 58 K. Pu2Pt3Si5 crystallizes in the U2Co3Si5-type orthorhombic Iabm structure (s.g. 72) with atomic parameters a = 9.9226(2) Å, b = 11.4436(2) Å and c = 6.0148(1) Å. The effective (leff 0.74 lB/Pu) and saturated (rsat...
-
Numerical analysis of crack propagation in silicone nitride
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculation...
-
HEAT TRANSFER CHARACTERISTICS OF ENHANCED SHELL AND COIL HEAT EXCHANGER
PublicationIn the paper authors presented their own constructions of shell and tube heat exchangers with intensified heat transfer. The shell and coils heat exchangers are in common use in heat ventilations and air conditioning systems. Those types of recuperators are quite simple constructions, the low value of pressure drops and good conditions of heat transfer. The present study shows an experimental investigation of the heat transfer...
-
Metody analizy nośności słupów żelbetowych z uwzględnieniem pełzania betonu
PublicationZgodnie z Eurokodem 2 nośność smukłych słupów żelbetowych można obliczać stosując uproszczone metody uwzględniania efektów II rzędu. W obliczeniach tych słupów istotną rolę odgrywa pełzanie, którego wpływ jest najmniej rozpoznany. W pracy zaproponowano dwa modele numeryczne uwzględniania wpływu pełzania. W pierwszym wpływ pełzania uwzględniono przez modyfikację charakterystyki materiałowej betonu, w drugim zastosowano prawo pełzania...
-
Crystal growth and properties of a binary intermetallic ZrBi2 compound
PublicationSingle crystals of ZrBi2 were grown by a self-flux method. The material adopts TiAs2 structure type with lattice parameters: a = 10.233(4) Å, b = 15.581(2) Å, c = 3.994(5) Å. Crystals of ZrBi2 were studied by means of magnetic susceptiblity, specific heat and resistivity measurements. The compound reveals a metallic-like behavior (RRR = 30). The Sommerfeld coefficient equals γ = 1.59(16) mJ mol-1 K-2 and Debye temperature ΘD =...
-
Short-range order structure and free volume distribution in liquid bismuth: X-ray diffraction and computer simulations studies
PublicationThe structure of liquid bismuth was studied by X-ray diffraction and computer simulation methods. The contraction of the atomic structure within the first coordination sphere in the temperature interval of 575- 1225 K is reported. The temperature dependencies of the coordination numbers and of the free volume are analysed. On the basis of the temperature dependencies of the free volume, the temperature dependencies of viscosity...
-
Experimental investigation of forced convection of water/EGAl2O3 nanofluids inside horizontal tube
PublicationIn this paper, forced convection of water/EG-Al2O3 nanofluids inside horizontal stainless steel tube is studied experimentally. As base fluid served water/EG mixture of two ratios (60:50 and 50:50). Nanoparticle mass concentrations was 0.1% or and 1%. Transition and turbulent flow regimes were tested. Average heat transfer coefficient and pressure drop values were determined for nanofluids and compared to base fluids. Deterioration...
-
Numerical investigation on the performance of a small counter-rotating wind turbine
PublicationThe article presents the results of the investigation on the performance of a small counter-rotating wind turbine. The wind turbine has been simulated using Computational Fluid Dynamics methods. Actuator Line Model has been successfully used to represent rotors in the computational domain. A parametric study has been carried out, taking into account changes in the tip speed ratio of the rotors while maintaining a constant distance...
-
On DoA estimation for rotating arrays using stochastic maximum likelihood approach
PublicationThe flexibility needed to construct DoA estimators that can be used with rotating arrays subject to rapid variations of the signal frequency is offered by the stochastic maximum likelihood approach. Using a combination of analytic methods and Monte Carlo simulations, we show that for low and moderate source correlations the stochastic maximum likelihood estimator that assumes noncorrelated sources has accuracy comparable to the...