Filters
total: 521
filtered: 506
Search results for: LIFE CYCLE
-
On the production of electricity in Poland using a geothermal binary power plant - A thermodynamic overview - Part I
PublicationPoland has a significant potential of geothermal energy. However, the high-temperature sources that are needed to drive power plants are found in relatively few places. Therefore, the objective of this paper is to consider any location in the northern part of Poland as a possible place to build a binary power plant. A scientific research was confirmed the existence of an elevated temperature gradient in this region. The hot rocks...
-
Influence of reactive oxygen species during deposition of iron oxide films by high power impulse magnetron sputtering.
PublicationIron oxide films were deposited using high power impulse magnetron sputtering (HiPIMS) of an iron cathode in an argon/oxygen gas mixture at different gas pressures (0.5~Pa, 1.5~Pa, and 5.0~Pa). The HiPIMS system was operated at a repetition frequency $f = 100$~Hz with a duty cycle of 1~\%. A main goal is a comparison of film growth during conventional and electron cyclotron wave resonance-assisted HiPIMS. The deposition plasma...
-
Criteria for selection of working fluid in low-temperature ORC
PublicationThe economics of an ORC system is strictly linked to thermodynamic properties of the working fluid. A bad choice of working fluid could lead to a less efficient and expensive plant/generation unit. Some selection criteria have been put forward by various authors, incorporating thermodynamic properties, provided in literature but these do not have a general character. In the paper a simple analysis has been carried out which resulted...
-
Ideas of the New European Bauhaus (NEB) in architectural education
PublicationThe New European Bauhaus (NEB) is an interdisciplinary project initiated by the European Commission in 2020 [1], based on three values: sustainability, beauty and community (social inclusion). Its aim is to support the European Green Deal programme [2] by accelerating the transformation of various economic sectors, including construction, to improve the quality of people’s lives and protect the natural environment. Even though...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublicationThe paper presents the results of a design analysis of a microturbine for a cogeneration micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3 kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attentionwas paid...
-
Gazowa mikrosiłownia domowa z modułem ORC - doświadczenia z badania prototypu
PublicationArtykuł zawiera rozważania nad ideą wykorzystania obiegu parowego ORC (Organic Rankine Cycle) do skojarzonej produkcji ciepła i energii elektrycznej dla pokrycia potrzeb indywidualnego odbiorcy. Dokonano w nim podsumowania dotychczasowych prac prowadzonych przez Autorów, które zaowocowały budową demonstracyjno-badawczego stanowiska mikro-CHP z technologią ORC w skali „domowej”, współpracującą z komercyjnym kotłem gazowym. W publikacji...
-
Analiza możliwości odzyskiwania ciepła odpadowego w przemyśle rafineryjnym z wykorzystaniem układów ORC
PublicationJednym z najważniejszych zagadnień współczesnej techniki jest poszukiwanie nowych możliwości pozyskiwania energii elektrycznej poprzez zagospodarowanie dotychczas niewykorzystanych lub bezużytecznie marnowanych jej źródeł. Jest to niezwykle ważna kwestia zarówno z ekonomicznego, technologicznego, jak i środowiskowego punktu widzenia. Jednym z przykładów nowoczesnych rozwiązań w tej dziedzinie może być zastosowanie układu opartego...
-
Comparison analysis of selected nuclear power plants supplied with helium from high-temperature gas-cooled reactor
PublicationThe article presents results of efficiency calculations for two 560 MW nuclear cycles with high-temperature gas-cooled reactor (HTGR). An assumption was made that systems of this type can be used in so-called marine nuclear power plants. The first analysed system is the nuclear steam power plant. For the steam cycle, the efficiency calculations were performed with the code DIAGAR, which is dedicated for analysing this type of systems....
-
Entrepreneurship Vulnerability to Business Cycle. A New Methodology for Identification Pro-cyclical and Counter-cyclical Patterns of Entrepreneurial Activity
PublicationIn literature, there is ongoing discussion whether entrepreneurial activity, approximated by, for instance, changes in self-employment, tends to behave pro-cyclically, counter-cyclically or rather is a-cyclical. Thus far, both theoretical and empirical evidence, where various multiple methodological approaches are used, does not provide clear answer to the latter; while widely offered explanations are scattered and lack robustness....
-
Partial Admission Stages of High Efficiency for a Microturbine
PublicationThe paper presents the results of a design analysis of a micro-turbine for a co-generation micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attention was...
-
The conception of energetic investigations of the multisymptom fatigue of the simple mechanical systems' constructional materials
PublicationThe article presents the basic assumptions of the research project aimed, as the main scientific purpose, an identification of the slow-changeable energy processes surrounding the high-cycle fatigue of constructional materials within the plain mechanical system, especially the marine one, for diagnostic purposes. There is foreseen an application of alternative diagnostic methods based on energetic observations of the multi-symptom,...
-
Heavy duty vehicle fuel consumption modelling using artificial neural networks
PublicationIn this paper an artificial neural network (ANN) approach to modelling fuel consumption of heavy duty vehicles is presented. The proposed method uses easy accessible data collected via CAN bus of the truck. As a benchmark a conventional method, which is based on polynomial regression model, is used. The fuel consumption is measured in two different tests, performed by using a unique test bench to apply the load to the engine. Firstly,...
-
Preparation of Hydrogen Electrodes of Solid Oxide Cells by Infiltration: Effects of the Preparation Procedure on the Resulting Microstructure
PublicationIn this work, the infiltration technique was used to produce hydrogen electrodes for solid oxide cells. Different infiltration methodologies were tested in order to try to shorten the infiltration cycle time. The porous scaffolds used for infiltration were based on highly porous yttria-stabilized zirconia (YSZ) obtained by etching the reduced nickel from the Ni-YSZ cermet in HNO3 acid. The support had a complex structure which...
-
Prediction of cast-in-place concrete strength of the extradosed bridge deck based on temperature monitoring and numerical simulations
PublicationThe work is devoted to the implementation of a monitoring system for high performance concrete embedded in the span of an extradosed bridge deck using a modified maturity method augmented by numerical simulations conducted by the authors’ FEM code. The paper presents all research stages of bridge construction and considers the conclusions drawn from the results of laboratory tests, field measurements, and numerical calculations....
-
Validation Process for Computational Model of Full-Scale Segment for Design of Composite Footbridge
PublicationExperimental tests and numerical simulations of a full-scale segment of a foot and cycle bridge made of polymer composites are presented in the paper. The analysed structure is made of sandwich panels, which consist of glass fibre reinforced polymer (GFRP) multi-layered laminate faces and a PET foam (obtained from recycling) core. The dimensions of the segment cross-section are the same as for the target footbridge; however, span...
-
Hysteresis curves for some periodic and aperiodic perturbations in magnetosonic flow
PublicationA thermodynamic relation between perturbations of pressure and mass density in the magnetohydrodynamic flow is theoretically studied. Planar magnetohydrodynamic perturbations with the wave vector, which forms a constant angle with the equilibrium magnetic field, are under study. The theory considers thermal conduction of a plasma and the deviation from adiabaticity of a flow due to some kind of heating–cooling function. It also...
-
Pressure drop and heat transfer during boiling and condensation at subcritical region
PublicationMost of the data presented in the literature relate to saturation temperatures in the range - 20°C to 40°C due to the application in refrigeration technology. There is necessity to extend databases to higher values of saturation temperature due to new applications such as Organic Rankine Cycle and high temperature heat pumps. Only few papers contain data for high reduced pressure for low boiling point liquids. This paper focus...
-
Cooperation of ORC installation with a gas boiler as a perspective co-generation system for households
PublicationThis paper reports tests of an innovative micro-CHP unit prototype, consisting of a traditional gas boiler and organic Rankine cycle (ORC), which incorporates original system components such as an axial vapour microturbine, evaporator and condenser. The system co-generates heat and electricity for a single household or a group of households. Electricity is only a by-product during production of heat. While testing the prototype,...
-
Experience-Based Decisional DNA (DDNA) to Support Product Development
PublicationKnowledge and experience are important requirements for product development. The aim of this paper is to propose a systematic approach for industrial product development. This approach uses smart knowledge management system comprising of Set of Experience Knowledge Structure and Decisional DNA (DDNA) along with Virtual Engineering Tools (Virtual engineering object, Virtual engineering process, and Virtual engineering factory)....
-
Effect of Pin Shape on Thermal History of Aluminum-Steel Friction Stir Welded Joint: Computational Fluid Dynamic Modeling and Validation
PublicationThis article studied the effects of pin angle on heat generation and temperature distribution during friction stir welding (FSW) of AA1100 aluminum alloy and St-14 low carbon steel. A validated computational fluid dynamics (CFD) model was implemented to simulate the FSW process. Scanning electron microscopy (SEM) was employed in order to investigate internal materials’ flow. Simulation results revealed that the mechanical work...
-
Negative carbon dioxide gas power plant integrated with gasification of sewage sludge
PublicationOne of the primary objectives of the negative carbon dioxide gas power plant (nCO2PP) is to develop an innovative technology confirming the possibility of the use of sewage sludge to produce electricity while having a positive impact on the environment. In this paper, a mathematical model is presented to estimate thermodynamic parameters of the system in relation to the gasification process and changes in such parameters in the...
-
THE ESSENCE OF THE TRANSFORMATION OF SOCIO-ECONOMIC RELATIONS IN THE NATIONAL ECONOMY: THEORETICAL AND METHODOLOGICAL ASPECT
PublicationThe article is devoted to a thorough study of the theoretical and methodological foundations of the essence of the transformation of socio-economic relations of the national economy. Based on the study of scientific sources, a proper definition of the concept of "transformation of socio-economic relations" was formed. It is proposed to consider transformational processes from the point of view of their direct or indirect impact...
-
Comprehensive thermodynamic analysis of the CAES system coupled with the underground thermal energy storage taking into account global, central and local level of energy conversion
PublicationA key aspect of CAES is the optimal configuration of the thermodynamic cycle. In this paper, the situation of cooperation between the current conventional power plants and wind farms is analyzed, and then, based on thermodynamic models, the process of storing thermal and electrical energy in the CAES system coupled with a heat storage and recovery is developed. Therefore, three levels can be distinguished, namely: the global level...
-
The valance state of vanadium-key factor in the flexibility of potassium vanadates structure as cathode materials in Li-ion batteries
PublicationPotassium hexavanadate (K2V6O16·nH2O) nanobelts have been synthesized by the LPE-IonEx method, which is dedicated to synthesis of transition metal oxide bronzes with controlled morphology and structure. The electrochemical performance of K2V6O16·nH2O as a cathode material for lithium-ion batteries has been evaluated. The KVO nanobelts demonstrated a high discharge capacity of 260 mAh g−1, and long-term cyclic stability up to 100...
-
Direct modulation for conventional matrix converters using analytical signals and barycentric coordinates
PublicationThis paper proposes the generalized direct modulation for Conventional Matrix Converters (CMC) using the concept of analytical signals and barycentric coordinates. The paper proposes a novel approach to the Pulse Width Modulation (PWM) duty cycle computing, which allows faster prototyping of direct control algorithms. The explanation of the new idea using analytical considerations demonstrating the principles of direct voltage...
-
An approach to improve the time efficiency of disjoint paths calculation
PublicationFailures of network elements can be appropriately dealt with by utilization of alternate disjoint paths to provide redirection of flows affected by failures of the respective working paths. Known approaches can be broadly divided by decision on backup paths installation into proactive and reactive mechanisms, as well as based on the scope of recovery actions into local and global rerouting. There are several important scenarios...
-
CO2 EMISSION TO THE ATMOSPHERE FROM CARBONATE WATERS: THE STUDY CASE OF THE LUBLIN UPLAND AND ROZTOCZE REGIONS
PublicationThe concentration of carbon dioxide dissolved in water (CO2(aq)) was measured in consecutive phases of the hydrological cycle. Its potentially possible degassing from groundwaters to the atmosphere was also assessed. The research was conducted in the area of occurrence of carbonate rocks of the Lublin Upland and Roztocze (SE Poland). The results of the measurements of CO2(aq) concentration varied as follows (min-max/mean): precipitation...
-
Network Graph Transformation Providing Fast Calculation of Paths for Resilient Routing
PublicationProtection of transmission against failures can be appropriately dealt with by alternative paths. However, common schemes (e.g., Bhandaris scheme) are characterized by a remarkable delay while determining the transmission paths. This in turn may have a serious impact on serving dynamic demands (characterized by relatively short duration time). As a remedy to this problem, we introduce an approach to pre-compute the sets of disjoint...
-
Utilizing Genome-Wide mRNA Profiling to Identify the Cytotoxic Chemotherapeutic Mechanism of Triazoloacridone C-1305 as Direct Microtubule Stabilization
PublicationRational drug design and in vitro pharmacology profiling constitute the gold standard in drug development pipelines. Problems arise, however, because this process is often dicult due to limited information regarding the complete identification of a molecule’s biological activities. The increasing aordability of genome-wide next-generation technologies now provides an excellent opportunity to understand a compound’s diverse eects...
-
Modelling of heat transfer in supercritical pressure recuperators
PublicationIn the paper presented is analysis of convective flow heat transfer at supercritical pressure in channels of heat exchanger working in the thermodynamic cycle. The modelling is based on the division of the flow into three regions, namely the heavy fluid, a two phase flow consisting of the heavy and light fluids and finally the light fluid flow. Modelling is concentrated on the region of simultaneous flow of two fluids divided into...
-
Novel chalcone-derived pyrazoles as potential therapeutic agents for the treatment of non-small cell lung cancer
PublicationLung cancer is considered to account for approximately one-fifth of all malignant tumor-related deaths worldwide and is therefore one of the most lethal malignancies. Pyrazole scaffold possesses a wide range of biological and pharmacological activities, which play important roles in medicinal chemistry. The present study reports the synthesis and in vitro biological characterization of nine pyrazoles derived from chalcones as potential...
-
Detection and removal of priority substances and emerging pollutants from stormwater: case study of the Kołobrzeska collector, Gdańsk, Poland
PublicationProgressive urban development affects environmental balance and disrupts the hydrologic cycle, in which rainfall plays a significant role. Since rainwater is considered a valuable resource of the environment, many technical solutions are implemented that enable effective rainwater management. On the other hand, stormwater runoff from urban areas contains numerous (also toxic) substances, and therefore should be properly treated....
-
DIGITAL HYDRAULICS CIRCUIT BASED ON PWM FUNCTION FOR CONTROLLING HYDRAULIC ACTUATOR POSITION
PublicationHydraulic systems are used in many different industries, such as multi-source hydrostatic drive systems. In traditional hydraulic systems, a proportional servo valve is used to control the position of hydraulic actuators. The low energy efficiency and high cost of these control valves are two major problems with these systems. Digital hydraulics is one of the most unique ideas on how to solve these problems. Researchers like digital...
-
Tetrahydroquinolinone derivatives exert antiproliferative effect on lung cancer cells through apoptosis induction
PublicationThe anticancer properties of quinolones is a topic of interest among researchers in the scientific world. Because these compounds do not cause side effects, unlike the commonly used cytostatics, they are considered a promising source of new anticancer drugs. In this work, we designed a brief synthetic pathway and obtained a series of novel 8-phenyltetrahydroquinolinone derivatives functionalized with benzyl-type moieties at position...
-
Numerical analysis of CO2-water separation in a horizontal double T-junction
PublicationCarbon dioxide is considered one of the main factors leading to global warming. Considering the significant impacts of CO2 on climate change, various technologies have been developed in recent decades to control carbon emission, such as for example CO2 capture and storage. The developed cycle of a negative CO2 emission power plant includes some devices, out of which, separator plays an indispensable role. To this end, T-junction...
-
High-efficiency mini and micro heat exchangers for dispersed power generation
PublicationTaking into account the dispersed systems technologies and their development, the ORC systems seem to be promising technology amongst various micro-CHP domestic units (electrical power production below 10 kWe), however practical realization of the ORC cycle in a micro-scale is technically challenging. The system consists in devices such as the vapour generation unit (boiler), expansion device and heat exchangers. Each of them should...
-
Investigation of ecological parameters of a gas turbine combustion chamber with steam injection for the floating production, storage, and offloading vessel
PublicationThe article is dedicated to the investigation of the possibility of using the contact type gas turbine cycle with steam injection into the combustion chamber for the floating production, storage, and offloading vessel in order to increase the specific power and efficiency and reduce emissions of toxic components. A new approach is proposed, associated with the use of the two-stage injection of superheated steam into a gas turbine...
-
New insights on lithium storage in silicon oxycarbide/carbon composites: Impact of microstructure on electrochemical properties
PublicationIn this work, we study the impact of the preceramic precursor vinyltriethoxysilane (VTES) on the electrochemical performance of silicon oxycarbide (SiOC) glass/graphite composites. We apply an innovative approach based on high-power ultrasounds in order to obtain highly homogenous composites with a uniform distribution of small graphitic flakes. This procedure enhances gelation and drying of VTES-based preceramic polymer/graphite...
-
Planning optimised multi-tasking operations under the capability for parallel machining
PublicationThe advent of advanced multi-tasking machines (MTMs) in the metalworking industry has provided the opportunity for more efficient parallel machining as compared to traditional sequential processing. It entailed the need for developing appropriate reasoning schemes for efficient process planning to take advantage of machining capabilities inherent in these machines. This paper addresses an adequate methodical approach for a non-linear...
-
A simple modification of PCR thermal profile applied to evade persisting contamination
PublicationThe polymerase chain reaction (PCR), one of the most commonly applied methods of diagnostics and molecular biology has a frustrating downside known as the false positive signal or contamination. Several solutions to avoid and to eliminate PCR contaminations have been worked out to date but the implementation of these solutions to laboratory practice may be laborious and time consuming. A simple approach to circumvent the problem...
-
A new viscoelastic method of calculation of low-temperature thermal stresses in asphalt layers of pavements
PublicationThe paper presents a new method of calculation of thermal stresses in asphalt layers of pavements induced by cooling or heating. The method, developed by the author, is based on the analytical solution for the linear viscoelastic Burgers model extended numerically for the case of asphalt layers whose rheological parameters are strongly dependent on temperature. The coefficient of thermal expansion and Poisson’s ratio may optionally...
-
Assessing ecotoxicity, synergic and antagonistic actions of commonly used components of polymerization mixture in molecularly imprinted polymers preparation process
PublicationIncreasingly, the challenge is the optimal process of developing a suitable MIP-type sorptive material (taking into account its final form and application area), which is mainly related to the efficiency/effectiveness of the polymerization process. The lack of reaction or its low efficiency generates additional waste and puts it into the environmental cycle. The main aim of the performed research was the estimation of ecotoxicity,...
-
Novel fused pyran derivatives induce apoptosis and target cell cycle progression in anticancer efficacy against multiple cell lines.
PublicationNitrogen-based heterocycles such as pyrazole, imidazole, 1,2,4-triazole, benzimidazole, and benzotriazole substituted fused pyran derivatives (6a–e, 8a–e, 10a–e, 12a–e,&14a–e) have been synthesized and tested for their in vitro anticancer efficacies against MCF7, A549, and HCT116 cancer cell lines. Among the compounds, 6e, 14b, and 8c were identified as the most potent against MCF7, A549, and HCT116, with IC50 values of 12.46 2.72...
-
Leaf wettability and plant surface water storage for common wetland species of the Biebrza peatlands (northeast Poland)
PublicationWetlands play a crucial role in buffering the effects of climate change. At the same time, they are one of the most endangered ecosystems on the globe. The knowledge of the water cycle and energy exchange is crucial for the practical preservation and exploiting their capabilities. Leaf wettability is an important parameter characterising the plant's ability to retain water on its surface, and is linked to the ecosystems' hydrological...
-
Comparison of traditional district heating with low temperature district heating systems featuring organic Rankine cycle and heat pump
PublicationPaper presents a comparison between a traditional district heating system with conventional boilers as a source of heat and electricity purchases from power utilities and a low temperature DH system incorporating the CHP with organic Rankine Cycle providing electricity and local heat pump raising the temperature of the DH fluid to the required temperature in the dwelling, meaning that both heat and electricity are produced within...
-
Współpraca pomp ciepła ze źródłem konwencjonalnym. Algorytmy obliczenia bilansu energetycznego i efektywności ekonomicznej
PublicationW wielu przypadkach pompy ciepła w instalacjach ogrzewania współpracują z innymi źródłami ciepła (kotły wodne opalane olejem opałowym, gazem ziemnym, biogazem, bojlery elektryczne, miejska lub osiedlowa sieć ciepłownicza) tworząc hybrydowe źródło ciepła. W każdym wariancie źródła hybrydowego odbiorcę i producenta ciepła interesuje bilans energetyczny całego obiektu oraz efektywność ekonomiczna wytwarzania ciepła w źródle hybrydowym...
-
Design and numerical testing of 5-box gfrp shell footbridge
PublicationThe paper formulates new design conditions for composite footbridges, taking into account the material and structural specificity of these objects, i.e. the strength condition, the serviceability condition and the frequency condition. A GFRP composite footbridge labelled with CFB2 code has been designed, with the original superstructure in the form of an opened-closed 5-box girder. The foot and cycle track bridge is simply supported,...
-
The new concept of capillary forces aided evaporator for application in domestic organic rankine cycle
PublicationThis paper presents studies on the possibility of applying capillary forces induced in the porous structure to a modern design of evaporator. The potential application of such heat exchanger is for example an evaporator of the domestic micro combined heat and power (CHP) unit. One of the problems in the micro-CHP is excessive demand for pumping power. The proposed design helps in overcoming that issue. In the evaporator outlined...
-
H2AX phosphorylation, its role in DNA damage response and cancer therapy
PublicationDouble-strand breaks (DSBs) are the most deleterious DNA lesions, which, if left unrepaired, may have severe consequences for cell survival, as they lead to chromosome aberrations, genomic instability, or cell death. Various physical, chemical, and biological factors are involved in DSB induction. Cells respond to DNA damage by activating the so-called DNA damage response (DDR), a complex molecular mechanism developed to detect...
-
Synthesis, molecular structure, and metabolic stability of new series of N' -(2-alkylthio-4-chloro-5-methylbenzenesulfonyl)-1-(5-phenyl-1 H -pyrazol-1-yl)amidine as potential anti-cancer agents
PublicationA series of new N'-(2-alkylthio-4-chloro-5-methylbenzenesulfonyl)-1-(5-phenyl-1H-pyrazol-1-yl)amidine derivatives have been synthesized and evaluated in vitro by MTT assays for their antiproliferative activity against cell lines of colon cancer HCT-116, cervical cancer HeLa and breast cancer MCF-7. The studied compounds display selective activity mainly against HCT-116 and HeLa cells. Thus, five compounds show selective cytotoxic...