displaying 1000 best results Help
Search results for: NON-LINEAR VISCOELASTICITY, NUMERICAL MODELLING, MSCR TEST, MASTIC.
-
Estimation of the steam condensation flow via CFD methods
PublicationThe results of numerical simulations to predict the performance of different steam models have been presented. All of the considered models of steam condensation have been validated on the base of benchmark experiment employing expansion in nozzle and next on the low pressure part of the steam turbine stage. For numerical analysis three models have been finally used – the ideal steam model without condensation, an equilibrium steam...
-
Key activities to improve energy management in DC microgrids connected by urban traction
PublicationDC MicroGrids must have Energy Management Systems to guarantee efficient, dependable, and environmentally friendly electricity. The application of Model Predictive Control, proved to be helpful due to its adaptability and capacity to use non-linear models. This paper, based on an extensive literature review, identifies and discusses the three key activities to improve the characteristics of DC MicroGrids, i.e.: the use of Energy...
-
In-service measurement of the small wind turbine test stand for structural health monitoring
PublicationThis paper presents the research activity performed on a Small Wind Turbine (SWT) test stand. Commercially available turbine was modified towards incorporation of the sensors system for condition monitoring. Installed sensors measure angular shaft position, torque applied from the wind loads, vibration accelerations and last but not least rotational speed. All gathered data are then transferred and processed in Test.Lab by means...
-
Regression points in non-intrusive polynomial chaos expansion method and D-optimal design
PublicationThe paper addresses selected issues of uncertainty quantification in the modelling of a system containing surgical mesh used in ventral hernia repair. Uncertainties in the models occur e.g. due to variability of abdominal wall properties among others. In order to include them, a non-intrusive regression-based polynomial chaos expansion method is employed. Its accuracy depends on the choice of regression points. In the study a relation...
-
Acoustic journal bearing - A search for adequate configuration
PublicationClassical non-contact bearings are already used in a number of specialist applications but there are somespecialist areas where they cannot be used for variety of reasons and acoustic sliding bearings could be an alternative. The paper presents the quest for a configuration of an acoustic journal bearing and shows that the overall shape of the bearing and its geometry are of a vital importance for the load capacity oft he bearing....
-
On FEM analysis of Cosserat-type stiffened shells. Static and stability linear analysis
PublicationThe present research investigates the theory and numerical analysis of shells stiffened with beams in the framework based on the geometrically exact theories of shells and beams. Shell’s and beam’s kinematics are described by the Cosserat surface and the Cosserat rod respectively, which are consistent including deformation and strain measures. A FEM approximation of the virtual work principle leads to the conforming shell and beam...
-
The database of interpolated RR-intervals of original length 512 of 41 patients at rest hospitalized due to the episode of acute ischemic stroke
Open Research DataThis dataset contains the data that was a basis for the results discussed in the paper “Persistent homology as a new method of the assessment of heart rate variability” by Grzegorz Graff, Beata Graff, Paweł Pilarczyk, Grzegorz Jabłoński, Dariusz Gąsecki, Krzysztof Narkiewicz, Plos One (2021), DOI: 10.1371/journal.pone.0253851.
-
The database of interpolated RR-intervals of length 512 of 46 healthy subjects at rest
Open Research DataThis dataset contains the data that was a basis for the results discussed in the paper “Persistent homology as a new method of the assessment of heart rate variability” by Grzegorz Graff, Beata Graff, Paweł Pilarczyk, Grzegorz Jabłoński, Dariusz Gąsecki, Krzysztof Narkiewicz, Plos One (2021), DOI: 10.1371/journal.pone.0253851.
-
SOLUTIONS OF THE INTERMEDIATE SUPPORT STRUC- TURES OF THE NORTHERN MARMARA HIGHWAY (ISTAN- BUL’S RING ROAD) IN THE CONTEXT OF SEISMIC ACTIVITY
PublicationIn 2014–2018, as a result of the expansion of the city of Istanbul in Turkey, a project was imple- mented consisting of building a northern ring road, called the Northern Marmara Highway. The concept of the structural design of the ring road’s intermediate supports aims at constructing sup- ports that according to the TURKISH DLH 2008 standard must comply with the design require- ments for the three calculated earthquake insensitivity...
-
A numerical analysis of the thermal effects in the jet impingement stagnation zone
PublicationMost of the flows occurring in the engineering systems are turbulent and their accurate numerical analysis is still challenging, especially when combined with the heat transfer. One of the methods of heat transfer enhancement is utilization of the turbulent impinging jets, which were recently applied also in the heat exchangers. Their positive impact on the heat transfer performance was proven, but many questions related to its...
-
Detection and Imaging of Debonding in Adhesive Joints of Concrete Beams Strengthened with Steel Plates Using Guided Waves and Weighted Root Mean Square
PublicationStrengthening of engineering structures is an important issue, especially for elements subjected to variable loads. In the case of concrete beams or slabs, one of the most popular approaches assumes mounting an external reinforcement in the form of steel or composite elements by structural adhesives. A significant disadvantage of adhesive joints is the lack of access to the adhesive film for visual condition assessment, thus, there...
-
Rotordynamic characteristics of a chamber seal
PublicationThe paper presents the results of numerical and experimental investigations into pressure forces generated in a turbine labyrinth seal of a modernized type. The experiments were performed on a single-stage air model turbine of the impulse type. The experiments were performed on a single-stage air model turbine of the impulse type. The experimental data were compared with theoretical results obtained by means of CFD Fluent Code....
-
Singular curves in the resultant thermomechanics of shells
PublicationSome geometric and kinematic relations associated with the curve moving on the shell base surface are discussed. The extended surface transport relation and the extended surface divergence theorems are proposed for the piecewise smooth tensor fields acting on the regular and piecewise regular surfaces. The recently formulated resultant, two-dimensionally exact, thermodynamic shell relations - the balances of mass, linear and angular...
-
Gesture Recognition With the Linear Optical Sensor and Recurrent Neural Networks
PublicationIn this paper, the optical linear sensor, a representative of low-resolution sensors, was investigated in the multiclass recognition of near-field hand gestures. The recurrent neural network (RNN) with a gated recurrent unit (GRU) memory cell was utilized as a gestures classifier. A set of 27 gestures was collected from a group of volunteers. The 27 000 sequences obtained were divided into training, validation, and test subsets....
-
Analytical Steady-State Model of the Pipeline Flow Process
PublicationThe paper addresses the issue of modeling the flow process in transmission pipelines. A base model used for numerical simulation is introduced. Under certain assumptions concerning steady state analysis, the differential equations describing the process are solved analytically for two cases: zero and nonzero inclination angle α. These equations describe a constant flow rate and a corresponding distribution of the pressure along...
-
Numeryczna analiza dynamiczna wieszaków w łukowym wiadukcie kolejowym. Analiza przypadku
PublicationW artykule przedstawiono analizę dynamiczną wiaduktu kolejowego w ciągu Centralnej Magistrali Kolejowej zlokalizowanego koło Huty Zawadzkiej. W analizie zwrócono szczególną uwagę na lokalną odpowiedź wieszaków na obciążenie przejeżdżającym pociągiem oraz wiatrem. Obliczenia przeprowadzono na podstawie wykonanego modelu MES. Zweryfikowano poprawność modelu poprzez porównanie uzyskanych wyników z wartościami pomierzonymi. Przeprowadzono...
-
Influence of grain shape on the mechanical behaviour of granular materials
PublicationWe performed series of numerical vertical compression tests on assemblies of 2D granular material using a Discrete Element code and studied the results in regard to the grain shape. The samples consist of 5000 grains made either of 3 overlapping discs (clump - grain with concavities) or of six-edged polygons (convex grain). These two types of grains have a similar external envelope, ruled with a geometrical parameter α. In the...
-
Hazardous material-related propagation of the effects of train accidents in the subgrade
PublicationA large part of the transport of hazardous materials is carried out by rail. Therefore, the security of these transports is becoming increasingly important. Every catastrophe involving dangerous materials has a negative impact on the participants of the incident and the surrounding environment, because its range is generally not local. It follows that in the event of a catastrophe, its effects should be minimized and remediation...
-
Implementation of the FOPID Algorithm in the PLC Controller - PWR Thermal Power Control Case Study
PublicationIn the paper authors describe proposition of design and verification procedures of the discrete Fractional Order PID (FOPID) algorithm for control of the Pressurized Water Reactor (PWR) thermal power near its nominal operating point. The FOPID algorithm synthesis consists of: off-line optimal tunning of its parameters in continuous time-domain with LQ (Linear Quadratic) performance index and simplified models of nuclear reactor...
-
Prevention of resonance oscillations in gear mechanisms using non-circular gears
PublicationOne of the main disadvantages of gear mechanisms is the occurrence of noise and vibrations. This study investigated the applicability of non-circular gears for preventing resonance oscillations in gear mechanisms. The influence of a small deviation of the gear centrodes from the nominal circles on kinematic and oscillatory characteristics was analysed. It was shown that a larger deviation results in a smaller resonance amplitude...
-
A comparative performance assessment of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublicationThis work presents the investigation results of a journal bearing lubricated with magnetorheological fluid that is activated by a local constant magnetic field to vary both the local flow resistance and pressure. The bearing performance is assessed via Finite Element Modelling (FEM) and results are corroborated by experiments. The FEM model uses the Bingham model to describe the fluid film. A dedicated test rig is used to assess...
-
Comparison of GPS tropospheric delays derived from two consecutive EPN reprocessing campaigns from the point of view of climate monitoring
PublicationThe main purpose of this research was to acquire information about consistency of ZTD (zenith total delay) linear trends and seasonal components between two consecutive GPS reprocessing campaigns. The analysis concerned two sets of the ZTD time series which were estimated during EUREF (Reference Frame Sub-Commission for Europe) EPN (Permanent Network) reprocessing campaigns according to 2008 and 2015 MUT AC (Military University...
-
Types of Surface Impurities versus the Quality of Brazed Joints
PublicationBrazing is one of the primary joining processes increasingly often applied in industry. Because of their mechanical properties, overlap joints are particularly popular when making brazed structures. The use of brazed joints in structures of critical importance requires that particular attention be paid to joint quality, e.g. by the appropriate cleaning of surfaces to be joined. The article presents results of non-destructive tests...
-
Selected local stability problems of channel section flanges made of aluminium alloys
PublicationThe paper addresses the issue of local buckling of compressed flanges of cold-formed thin-walled channel columns and beams with nonstandard flanges composed of aluminium alloys. The material behaviour follows the Ramberg–Osgood law. It should be noted that the proposed solution may be also applied for other materials, for example: stainless steel, carbon steel. The paper is motivated by an increasing interest in nonstandard cold-formed...
-
Investigation of the 16-year and 18-year ZTD Time Series Derived from GPS Data Processing
PublicationThe GPS system can play an important role in activities related to the monitoring of climate. Long time series, coherent strategy, and very high quality of tropospheric parameter Zenith Tropospheric Delay (ZTD) estimated on the basis of GPS data analysis allows to investigate its usefulness for climate research as a direct GPS product. This paper presents results of analysis of 16-year time series derived from EUREF Permanent Network...
-
A simplified approach to determine the expiration date of certified reference material based on the results of monitoring long-term stability
PublicationAll components of the quality assurance (QA) system for measurement results depend heavily on certified reference materials (CRMs). There is a need for a comprehensive discussion of the stability study using the CRM statistical method. Monitoring involves periodic sampling and analysis of the CRM at predetermined intervals to continuously monitor stability without compromising its integrity. The obtained stability data is then...
-
Vibration of the bridge under moving singular loads - theoretical formulation and numerical solution
PublicationThe paper presents the results of the numerical analysis of a simple vehicle passing over a simply supported bridge span. The bridge is modelled by a Euler-Bernoulli beam. The vehicle is modelled as a linear, visco-elastic oscillator, moving at a constant speed. The system is described by a set of differential equations of motion and solved numerically using the Runge-Kutta algorithm. The results are compared with the solution...
-
Methodology of estimating temperature measurement uncertainty in a system for endurance tests.
PublicationThe team consisting of the article authors developed a non-invasive method and a system for measuring temperature during an endurance test. A thermocouple which provided the required accuracy of changes in temperature dynamics measurements was used for the purpose of the required research. The paper presents the methodology for estimating uncertainty of temperature measurement done with the presented system, using a method based...
-
Arch bridges under test loadings
PublicationThis paper illustrates experience in arch bridges test loadings of the research team of Department of Structural Mechanics and Bridge Structures from the Gdansk University of Technology. The presented calculations results constist the analysis of spatial construction schemes made using the finite elements method (FEM) and its comparison to the field studies. Arch bridges with the longest spans, visualisation of the computational...
-
Structural response of existing spatial truss roof construction based on Cosserat rod theory
PublicationPaper presents the application of the Cosserat rod theory and newly developed associated finite elements code as the tools that support in the expert-designing engineering practice. Mechanical principles of the 3D spatially curved rods, dynamics (statics) laws, principle of virtual work are discussed. Corresponding FEM approach with interpolation and accumulation techniques of state variables are shown that enable the formulation...
-
Nośność konstrukcji gruntowo-łukowej prefabrykowanego wiaduktu w świetle obliczeń numerycznych i badań „in situ”
PublicationWartykule przedstawiono analizy przeprowadzone dla wiaduktu WK-15 Pomorskiej Kolei Metropolitalnej wykonanego w technologii łuków prefabrykowanych przykrytych gruntem (system TechSpan). W celu weryfikacji obliczeń numerycznych wykonano próbne obciążenie konstrukcji. Przedstawiono wyniki pomiarów naprężeń i prezmieszczeń konstrukcji. Odniesiono się krytycznie do zastosowanego modelu obliczeniowego.
-
Mechanical properties for preliminary design of structures made from PVC coated fabric
PublicationIn this paper, laboratory tests necessary for the identification of non-linear elastic immediate properties of the PVC coated polyester fabric (like AF 9032) are described. The material parameters are specified on the basis of the uniaxial tensile tests in the warp and weft directions as well as on the base of the biaxial tensile tests. For the identification process techniques based on the least squares method are used. The authors...
-
Launching of steel bridge girder. Application of nonlinear shell models
PublicationThe paper describes the final technology of launching the steel bridge superstructure. The original technology failed in the first construction stage. Local damage of steel webs caused by plastic buckling stopped the procedure. In the effect of damage a new consulting team was employed to solve the problem and redesign a technology of constructing. The key element of the new solution was developed with great help of non-linear...
-
Wideband Model Order Reduction for Macromodels in Finite Element Method
PublicationAbstract: This paper presents a novel algorithm for accelerating 3D Finite Element Method simulations by introducing macromodels created in local model order reduction in the selected subdomains of the computational domain. It generates the projection basis for a compact system of equations associated with a separate subdomain. Due to non-linear frequency dependency in the Right Hand Side (RHS), the standard reduction methods do...
-
Anti-plane waves in an elastic thin strip with surface energy
PublicationWe consider anti-plane motions of an elastic plate taking into account surface energy within the linear Gurtin–Murdoch surface elasticity. Two boundary-value problems are considered that describe complete shear dynamics of a plate with free faces or with free and clamped faces, respectively. These problems correspond to anti-plane dynamics of an elastic film perfectly or non-perfectly attached to a rigid substrate. Detailed analysis...
-
Areas of updraft air motion from WRF model simulations.
Open Research DataPresented dataset is a part of numerical modelling study focusing on the analysis of sea ice floes size distribution (FSD) influence on the horizontal and vertical structure of convection in the atmosphere. The total area and spatial arrangement of the updrafts indicates that the FSD affects the total moisture content and the values of area averaged...
-
Hybrid technique for the analysis of circular waveguide junctions loaded with ferrite posts
PublicationThis study presents a hybrid technique for the analysis of circular waveguide junctions loaded with axially symmetrical ferrite posts of irregular shape. The method is based on a combination of the finite-difference frequency- domain technique with a mode-matching technique. The proposed approach is validated by comparing the presented results with numerical ones obtained from commercial software. The application of a cylindrical...
-
Application of Feed Forward Neural Networks for Modeling of Heat Transfer Coefficient During Flow Condensation for Low and High Values of Saturation Temperatur
PublicationMost of the literature models for condensation heat transfer prediction are based on specific experimental parameters and are not general in nature for applications to fluids and non-experimental thermodynamic conditions. Nearly all correlations are created to predict data in normal HVAC conditions below 40°C. High temperature heat pumps operate at much higher parameters. This paper aims to create a general model for the calculation...
-
A Mesh Deformation Technique Based on Solid Mechanics for Parametric Analysis of High-Frequency Devices With 3-D FEM
PublicationIn this paper, a versatile technique for mesh defor- mation is discussed, targeted at the electromagnetic (EM) field simulation of high-frequency devices using the 3-D finite element method (FEM). The approach proposed applies a linear elasticity model to compute the displacements of the internal mesh nodes in 3-D when the structure geometry is changed. The technique is compared with an alternative approach...
-
Electrochemical cell impedance spectra at Eoc+100mV
Open Research DataThe dataset presents impedance spectrum of electrochemical cell filled with 3% NaCl solution presented in the figure below. This cell was used measured using Atlas-Sollich 0531 impedance analyser with built-in potentiostat. When changing the DC polarisation of the cell the non-linear phenomena could be observed. The impedance spectrum frequency range...
-
Electrochemical cell impedance spectra at Eoc+200mV
Open Research DataThe dataset presents impedance spectrum of electrochemical cell filled with 3% NaCl solution presented in the figure below. This cell was used measured using Atlas-Sollich 0531 impedance analyser with built-in potentiostat. When changing the DC polarisation of the cell the non-linear phenomena could be observed. The impedance spectrum frequency range...
-
Electrochemical cell impedance spectra at Eoc-100mV
Open Research DataThe dataset presents impedance spectrum of electrochemical cell filled with 3% NaCl solution presented in the figure below. This cell was used measured using Atlas-Sollich 0531 impedance analyser with built-in potentiostat. When changing the DC polarisation of the cell the non-linear phenomena could be observed. The impedance spectrum frequency range...
-
Electrochemical cell impedance spectra at Eoc
Open Research DataThe dataset presents impedance spectrum of electrochemical cell filled with 3% NaCl solution presented in the figure below. This cell was used measured using Atlas-Sollich 0531 impedance analyser with built-in potentiostat. When changing the DC polarisation of the cell the non-linear phenomena could be observed. The impedance spectrum frequency range...
-
Electrochemical cell impedance spectra at Eoc-200mV
Open Research DataThe dataset presents impedance spectrum of electrochemical cell filled with 3% NaCl solution presented in the figure below. This cell was used measured using Atlas-Sollich 0531 impedance analyser with built-in potentiostat. When changing the DC polarisation of the cell the non-linear phenomena could be observed. The impedance spectrum frequency range...
-
New Tool for Examining QoS in the VToIP Service
PublicationThis paper is dedicated to the subject of measuring QoS in the Video Telephony over IP (VToIP) service. QoS measurement models in general and then models designed specifically for measuring QoS in the VToIP service are presented. A new numerical tool for examining the quality of VToIP video streams VToIP is described. The tool’s functionality is then put to the test in a number of analysis scenarios. The results and insights gained...
-
Numerical and experimental investigation of thermal convection near electric devices with vertical channels
PublicationThis paper presents the results of numerical and experimental investigation of thermal convection near heat emitting surfaces of an electric device. For the intensification of thermal convection, special vertical channels were formed near the heat emitting surfaces of the device. An experimental test has proved that there is an optimal length of the channels – thermal convection is the most intensive then. Air velocity vectors...
-
TiN coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #B48/#A45
Open Research DataWear tests in sliding friction of TiN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiN over TiN . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 12 min....
-
TiC coating in ring-on-ring sliding with saline solution (0.9%) lubrication 5MPa, 0.1m/s specimn. #B41/#A39
Open Research DataWear tests in sliding friction of TiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiC over TiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9%). Tribometer: PT-3. Overall test time till coating penetration 9 min....
-
CrN coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #A23/#B22
Open Research DataWear tests in sliding friction of CrN coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, CrN over CrN . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 12 min. The...
-
TiC coating in ring-on-ring sliding with distlled water lubrication 5MPa, 0.1m/s specimn. #B39/#A41
Open Research DataWear tests in sliding friction of TiC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, TiC over TiC . Mean contact stress: 5MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: DISTILLED WATER. Tribometer: PT-3. Overall test time till coating penetration 3 min. The test...