Search
Filters
total: 1450
-
Catalog
displaying 1000 best results Help
Search results for: ION-SELECTIVE SEPARATION
-
Study of the effect of adiabatic heating on the operation of the electrodynamic actuator
PublicationElectrodynamic actuators are used in hybrid switching systems where a very quick contact separation as well as operation repeatability and long-term reliability are required. The article presents selected results of thermal studies in the electrodynamic drive system. Study was carried out on the basis of the 3D electromagneto-thermal model implemented in the Ansys_Maxwell environment. The present model allows to determine the critical...
-
The profiles and spectrum of aqua solution of tannic acid by HPLC-DAD-MS analysis.
Open Research DataThe profiling of tannic acid is determined by examining the content and proportion / ratio of gallotannins [Aras et al. 2016, Clifford et al. 2007, Gauri et al. 2012, Nishizawa et al. 1982]. In order to check the ion mass distribution (TIC) in an aqueous solution of commercial tannic acid, a direct sample injection (TA) was performed into the mass spectrometer....
-
Valence state of Manganium in a MnCoO ceramics
Open Research DataManganium -cobalt based ceramics materials were produced by solid state reaction and sintred in a furnance in air atmosphere for 20h. Annealing temperature was 600 Celsius degree. For investigations a series of samples, with a various composition was chosen: MnCoO, Mn, Co2O and Mn2CoO. In order to determine valence states of the Mn, X-Ray photoemission...
-
Lanthanum investigations in ceramics annealed in a dry and wet atmosphere
Open Research DataCeramics based on Barium, Lanthanum, Gadolinium and Cobaltium were produced by standard solid state reaction from oxides and carbonate powders. After sintring, samples were annealed for 2 hours or 72 hours at 300 Celsius degree in a both: wet and dry atmosphere. Results of annealing on a chemical composition and valence state of lanthanum were observed...
-
central European Array for Gamma Levels Evaluation at Heavy Ion Laboratory, University of Warsaw
Research Equipment -
Correlations of structural, thermal and electrical properties of sodium doped complex borophosphosilicate glass
PublicationBorophosphosilicate glasses with varying sodium ion concentrations were investigated for their, structural, thermal, and electrical properties. All the obtained glasses were transparent except the glass with the highest sodium content, which exhibited translucency due to inhomogeneities. Increasing sodium content led to reduced boron and silicon content while maintaining a constant B/Si ratio, indicating progressive depolymerization...
-
On the Structure and Volumetric Properties of Solvated Lanthanoid(III) Ions in Amide Solutions
PublicationThe coordination chemistry and the volumetric properties of three representative lanthanoid(III) ions lanthanum-(III), gadolinium(III), and lutetium(III) have been studied in three amide solvents with gradually increasing spatial demand upon coordination: N,N-dimethylformamide (dmf)
-
Recent advances on magnetic carbon-related materials in advanced oxidation processes of emerging pollutants degradation
PublicationRecently, carbon-related materials have been proposed to improve the charge separation of the photogenerated carriers in the semiconductor matrices’ and surface properties. Carbon-related materials may act as co-catalysts, enhancing the pollutants adsorption on the surface, improving the charge carriers separation and photocatalyst stability and providing more active centres for photocatalytic reactions. This review summarizes...
-
Sano-Tachiya-Noolandi-Hong, Onsager and Braun models vs Monte Carlo simulation of charge photogeneration in organic solids
PublicationThe Sano-Tachiya-Noolandi-Hong (STNH), Onsager, and Braun models as well as Monte Carlo (MC) simulations of charge recombination/separation have been applied for the first time to reproduce the results of the electromodulated photoluminescence measurements in vacuum-evaporated films of fluorescent materials commonly used in optoelectronic devices. The values of the electron-hole pair final recombination speed in the monomer emitters:...
-
Unfolding new values in the landscape of conflict
PublicationThe main objective of the paper is to investigate how the conflict quality of landscape can be used as its asset and potential for creating new values. Like mediation between different overlapping archaeologies offers a basis for the perception of place in the chronology of time, the mediation between conflicted areas creates a capacious zone for enhancing the unique quality of landscape in its architectural, social, cultural and...
-
Investigating the effects of structural pounding on the seismic performance of adjacent RC and steel MRFs
PublicationAn insufficient separation distance between adjacent buildings is the main reason for structural pounding during severe earthquakes. The lateral load resistance system, fundamental natural period, mass, and stiffness are important factors having the influence on collisions between two adjacent structures. In this study, 3-, 5- and 9-story adjacent reinforced concrete and steel Moment Resisting Frames (MRFs) were considered to investigate...
-
Immunosuppressive properties of amino acid and peptide derivatives of mycophenolic acid
PublicationMycophenolic acid (MPA) was coupled with amino acids and biologically active peptides including derivatives of tuftsin to modify its immunosuppressive properties. Both amino acid unit in the case of simple MPA amides and modifications within peptide moiety of MPA - tuftsin conjugates influenced the observed activity. Antiproliferative potential of the obtained conjugates was investigated in vitro and MPA amides with threonine methyl...
-
Electrochemical Activity of Electrode Material Consisting of Porous Copper and Silica Aerogel
PublicationElectrochemically obtained copper was combined with silica aerogel (SiO2ag). Obtained composite (SiO2@Cu/CuxOy) was tested as an electrode in contact with LiPF6 in EC/DMC electrolyte. The electrochemical measurements showed the presence of complex redox couple activities of SiO2@Cu/CuxOy. This experiment was employed to help in understanding the carbon role used as an electric contact for silica in Li-Ion batteries and clarify...
-
Solvation of alkaline earth metal ions in N,N-dimethylformamide and N,N-dimethylacetamide – A volumetric and acoustic study
PublicationDensities and sound velocities at temperatures (298.15, 303.15, 308.15, 313.15 and 318.15) K of magnesium(II), calcium(II) and strontium(II) rifluoromethanesulfonates (triflates), as well as barium(II) perchloratein N,N-dimethylformamide (dmf) and N,N-dimethylacetamide (dma) have been measured over the composition range studied. From these results, apparent molar volumes and apparent molar isentropic compressibilities at infinite...
-
Multiple Group Membership and Collective Action Intention
PublicationDatasets from two studies conducted in Poland on the relation between identity fusion, group identification, multiple group membership, perceived injustice, and collective action intention. The presented studies, in the context of protests against attempts to restrict abortion law, were conducted to examine the link between belonging to multiple groups, group efficacy & identification, perceived injustice and collective...
-
Distribution of roughness and waviness components of turned surface profiles
PublicationThe paper presents a spectral formulation of surface profile irregularity in a wideband frequency range for roughness, waviness and shape components along the measured length. A unique distribution of roughness and waviness components is proposed, according to the nature of their origination in the course of machining with tools of defined cutting edge, as distinct from standard filtration in measurements of surface irregularities....
-
Liquid residence time in vortex separators
PublicationCentrifugal force enhances gravitational separation of suspension (vortex separators), as well as allows regulation of liquid discharge (vortex flow controls). Furthermore, it elongates the effective residence time of liquid inside the chamber in comparison to non-circulative flow. Laboratorz measurements, described in the paper, indicate that average liquid residence time for circulative flow exceeds 50% of plug-flow time,...
-
Singlet oxygen in the removal of organic pollutants: An updated review on the degradation pathways based on mass spectrometry and DFT calculations
PublicationThe degradation of pollutants by a non-radical pathway involving singlet oxygen (1O2) is highly relevant in advanced oxidation processes. Photosensitizers, modified photocatalysts, and activated persulfates can generate highly selective 1O2 in the medium. The selective reaction of 1O2 with organic pollutants results in the evolution of different intermediate products. While these products can be identified using mass spectrometry...
-
Green and Sustainable Membranes: A review
PublicationMembranes are ubiquitous tools for modern water treatment technology that critically eliminate hazardous materials such as organic, inorganic, heavy metals, and biomedical pollutants. Nowadays, nano-membranes are of particular interest for myriad applications such as water treatment, desalination, ion exchange, ion concentration control, and several kinds of biomedical applications. However, this state-of-the-art technology suffers...
-
A novel approach for processing CaAlSiON glass-ceramics by spark plasma sintering: Mechanical and electrical properties
PublicationLithium containing glassy materials can be used as solid electrolytes or electrode materials for lithium-ion batteries due to their high energy density. Conventional melt-quenched Ca11Al14Si16O49N10 glass powder containing 24 e/o N, doped with Li-ions (1, 3, and 6 wt. %) and sintered by spark plasma sintering technique (SPS) was studied. The benefits of using SPS to produce glass-ceramics are rapid heating rates compared to conventional...
-
Bias-Dependent Dynamics of Degradation and Recovery in Perovskite Solar Cells
PublicationDegradation of perovskite solar cells (PSCs) is often found to be partially or fully reversible when the cells are allowed to recover in the dark. Unlike the dynamics of degradation, knowledge about the dynamics of PSC cell recovery is very limited. Here, we demonstrate that the PSC recovery strongly depends on the electrical bias conditions during the light-induced degradation and that it can be manipulated by applying an external...
-
Cu( II ) ions removal from wastewater using starch nanoparticles ( SNPs ): An Eco‐sustainable approach
PublicationThe complex structured starch particles were reduced to the nanoscale size range through hydrolysis utilizing low concentration acid assisted with ultrasound irradiation. The synthesized starch nanoparticles (SNPs) were characterized by TEM, FTIR, and XRD techniques. The synthesized SNPs possessed surface activated entities, as many cationic functional groups were confirmed through the FTIR spectrum. Also, these SNPs were effectively...
-
Lead In drinking water: Adsorption method and role of zeolitic imidazolate frameworks for its remediation: A review
PublicationDue to various characteristics properties lead(II) metal is utilized in many applications like lead ion batteries, water pipes, ammunition and paints. For this reason, concentration of lead(II) ions in water is increasing days by days which is alarming for water pollution. Water pollution is a major problem worldwide which affects biosphere badly, and causes continuous reduction of accessible sources of fresh water and ground water, available...
-
n/d n/d
ProjectsProject realized in Faculty of Chemistry according to Homing Plus/2012-6/16 agreement from 2013-05-22
-
Multi-DBD actuator with floating interelectrode for aerodynamic control
PublicationIn this paper the use of a floating inter-electrode in a multi-DBD (dielectric barrier discharge) plasma actuator is described. The multi-DBD plasma actuators with floating inter-electrodes were investigated to get a longer DBD on a dielectric surface and to maximise generated net airflow. Our actuator was used to control the boundary layer flow separation around NACA0012 airfoil model. The results of our investigations suggests...
-
Two-dimensional gas chromatography – principles and application in fruits analysis
PublicationTwo-dimensional gas chromatography is a rapidly developing analytical technique. One of the major uses of this technique is its use for food analysis. The paper presents the principle of operation and history of this analytical technique. The specification of the two-dimensional gas chromatography technique has been discussed. The principles of separation of ingredients and application of the method, particularly in the analysis...
-
Validation of lumbar spine finite element model
Open Research DataThe functional biomechanics of the lumbar spine have been better understood by finite element method (FEM) simulations. However, there are still areas where the behavior of soft tissues can be better modeled or described in a different way. The purpose of this research is to develop and validate a lumbar spine section intended for biomechanical research....
-
Very low resolution depth images of 200,000 poses
Open Research DataA dataset represents simulated images of depth sensor seeing a single human pose, performing 200,000 random gestures. The depth images as vectors of pixels are stored with ground truth positions of every relevant joint.
-
Potential energy curves of the doublet Sigma gerade plus states of the Lithium dimer cation
Open Research DataAdiabatic potential energy curves of the doublet Sigma gerade plus (dSg+) states have been calculated for the Lithium dimer cation (Li2+). The results of the ground state and four excited states of the symmetry doublet Sigma gerade plus have been obtained by the nonrelativistic multireference configuration interaction (MRCI) method used with pseudopotentials...
-
Potential energy curves of the doublet Sigma ungerade plus states of the Lithium dimer cation
Open Research DataAdiabatic potential energy curves of the doublet Sigma ungerade plus (dSu+) states have been calculated for the Lithium dimer cation (Li2+). The results of the five excited states of the symmetry doublet Sigma ungerade plus have been obtained by the nonrelativistic multireference configuration interaction (MRCI) method used with pseudopotentials describing...
-
Potential energy curves of the doublet Pi and Delta gerade states of the Lithium dimer cation
Open Research DataAdiabatic potential energy curves of the doublet Pi and Delta gerade (dPg and dDg) states have been calculated for the Lithium dimer cation (Li2+). The results of the four excited states of the symmetries doublet Pi and Delta gerade have been obtained by the nonrelativistic multireference configuration interaction (MRCI) method used with pseudopotentials...
-
Potential energy curves of the doublet Pi and Delta ungerade states of the Lithium dimer cation
Open Research DataAdiabatic potential energy curves of the doublet Pi and Delta ungerade (dPu and dDu) states have been calculated for the Lithium dimer cation (Li2+). The results of the four excited states of the symmetries doublet Pi and Delta ungerade have been obtained by the nonrelativistic multireference configuration interaction (MRCI) method used with pseudopotentials...
-
Rain Gardens SW quality dataset
Open Research DataThis dataset contains the results of parameters of storm water runoff and storm water quality in rain garden units. Samples were collected from 4 different rain gardens in Gdansk, Poland.
-
ESTIMATION OF YOUNG`S MODULUS OF THE POROUS TITANIUM ALLOY WITH THE USE OF FEM PACKAGE
PublicationPorous structures made of metal or biopolymers with a structure similar in shape and mechanical properties to human bone can easily be produced by stereolithographic techniques, e.g. selective laser melting (SLM). Numerical methods, like Finite Element Method (FEM) have great potential in testing new scaffold designs, according to their mechanical properties before manufacturing, i.e. strength or stiffness. An example of such designs...
-
Te use of acoustic emission for assessment of the oil lubricity in a four-ball tester
Publicationin view of the increased dynamic and temperature load in the compression-ignition engine tribological systems, particular attention is drawn to the problem of such lubrication of the friction nodes that after breaking the boundary layer it could be restored without any wear occurring. therefore, an idea has been devised of introducing to friction nodes, with the lubrication oils, of new substances (operational preparations) modifying...
-
Label‐free optical detection of cyclosporine in biological fluids
PublicationIn this paper, a spectroscopic method for determination of cyclosporine concentrations in biological fluids is presented. Blood plasma and hemoglobin solutions are chosen for the experiment. For various cyclosporine concentrations in blood plasma and hemoglobin, absorbance measurements in spectra range from 600 to 1100 nm are performed. The measurement results are analyzed by the use of a dedicated algorithm. The obtained data...
-
3D Printing of Metallic Implants
PublicationThe fabrication of various elements, solid and open porous structures of stainless steel and Ti alloy is described. The process was started with the design of 3D models in CAD/CAM system. The 3D models were transformed into *.stl files and then the manufacturing process of the real structures by means of the selective laser melting with the SLM Realizer 100 3D printer was made. The paper shows the porous specimens made for possible...
-
Effect of molar ratio [NCO]/[OH] groups during prepolymer chains extending step on the morphology and selected mechanical properties of final bio‐based thermoplastic poly(ether‐urethane) materials
PublicationThe main aim of this work was to investigate the effect of [NCO]/[OH] molar ratio used during the prepolymer chain extending step (with bio‐based diols) on the chemical structure, and thermomechanical and mechanical properties of thermoplastic poly(ether‐urethane)s. Thermoplastic poly(ether‐urethane)s were obtained from bio‐based polyol (polytrimethylene ether glycol), bio‐based glycol (1,4‐butanediol or 1,3‐propanediol), and 4,4'diphenylmethane...
-
Imidazolium silanethiolates relevant to the active site of cysteineproteases. A cooperative effect in a chain of NH(+)...S(-) hydrogenbonds
PublicationThree imidazolium silanethiolates relevant to the active site of cysteine proteases have been synthesized and investigated by X-ray diffraction, IR spectroscopy and computational methods. As indicated by crystallographic and FT-IR data in the solid state, the transfer of proton from thiol to imidazole takes place and a thiolato-imidazolium ion pair is formed. The FT-IR spectra of crystalline imidazolium silanethiolates exhibit...
-
Influence of Operation Conditions on Temperature Hazard of Lithium-Iron-Phosphate (LiFePO4) Cells
PublicationThe article presents and discusses the results of research on hazard, especially temperature, for selected lithium-ion-phosphate cells operated in accordance with the manufacturer’s recommendations but used under onerous mining conditions. This applies to the performance of cells in battery sets without the application of any management system (BMS). On the basis of the obtained test results, first of all, the influence of the...
-
9 - Solid oxide fuel and electrolysis cells
PublicationIn this chapter, the fundamental reactions, the geometrical designs, the material requirements, and the status of SOFCs and SOECs are presented. In the following seven chapters, the most important components of an SOC are described and the chapter ends with a summary and outlook. The described components are: (i) oxygen-ion conductors (electrolyte), (ii) anode materials for SOFCs (cathode in SOEC mode), (iii) cathode materials...
-
STRATEGIA DOBORU PROCESU PRODUKCYJNEGO WG. REAKCJI NA ZAMÓWIENIA KLIENTA
PublicationW opracowaniu poruszono zagadnienie doboru strategii wytwarzania w zakresie procesu produkcyjnego. W ramach tego zagadnienia dokonano podziału procesów produkcyjnych wg różnych kryteriów. Skupiano się na podziale procesów wg. reakcji na zamówienia klienta. Przedstawiono pokrótce najistotniejsze cechy charakteryzujące tego typu procesy. By móc określić strategię w zakresie procesu produkcyjnego zestawiono kryteria wyboru procesu...
-
Isolation of Human Progenitor Epidermal Cells on Collagen Type IV and Analysis of Their Markers with Flow Cytometry and PCR Methods
PublicationEpidermal stem cells, located in the skin, together with keratinocytes are transplanted in regenerative therapies, e.g., for the treatment of burns or other wounds. Here, we describe the protocol of their enzymatic isolation from human skin. It includes separation of the epidermis form the dermis by incubation with dispase followed by cell isolation for epidermis by digestion with trypsin. Cell isolated with this method can be...
-
Quasirelativistic potential energy curves and transition dipole moments of NaRb
PublicationWe report on extensive calculations of quasi-relativistic potential energy curves and, for the first time, transition dipole moments including spin-orbit and scalar-relativistic effects of the NaRb molecule. The calculated curves of the 0+, 0-, 1, 2 and 3 molecular states correlate for large internuclear separation with the fourteen lowest atomic energies up to the Na(3s ^2S_{1/2}) + Rb(7s ^2S_{1/2}) atomic limit. Several new features...
-
Thermodynamics of aggregation of 1-methyl-3-tetradecylimidazolium chloride in an aqueous solution
PublicationZbadano zależność agregacji chlorku 1-metylo-3-tetradecyloimidazoliowego w środowisku wodnym od temperatury. Wyznaczono krytyczne stężenie agregacji (CAC) oraz stopień jonizacji metodą pomiaru przewodnictwa właściwego. Otrzymane wyniki wykorzystano do predykcji parametrów termodynamicznych - entalpii swobodnej, entalpii i entropii, stosując phase separation model. Wykazano, że krzywa zależności CAC od temperatury jest U-kształtna...
-
Magnetic field microsensor based on GaAs MESFET
PublicationA novel concept of the drain separation design in a horizontally-split-drain GaAs MAGFET sensor, based on epitaxial layer growth, was developed. Proper choice of GaAs/AlAs/GaAs epitaxial layer sequence provided good electrical isolation between the drain regions. The measured leakage current between the drain regions was in the range of nA for up to 2V drain voltage bias difference. Performed analytical and numerical calculations...
-
Optical-Spectrometry-Based Method for Immunosuppressant Medicine Level Detection in Aqueous Solutions
PublicationIn this paper, an investigation into detecting immunosuppressive medicine in aqueous solutions using a spectrometry-based technique is described. Using optical transmissive spectrometry, absorbance measurements in the spectra range from 250 nm to 1000 nm were carried out for different cyclosporine A (CsA) concentrations in aqueous solutions. The experiment was conducted for samples both with and without interferent substances—glucose...
-
Recent developmentsinthesynthesisand biological activityofacridine/acridoneanalogues
PublicationMany people in the world struggle with cancer or bacterial, parasitic, viral, Alzheimer's and other diseases. Therefore, many scientists seek new, more effective, more selective and less toxic drugs. Acridine/acridone derivatives constitute a class of compounds with a broad spectrum of biological activity and are of great interest to scientists. Todate, many acridine/acridone analogues have been obtained,which, inter alia, exhibit...
-
Green chromatography
PublicationAnalysis of organic compounds in samples characterized by different composition of the matrix is very important in many areas. A vast majority of organic compound determinations are performed using gas or liquid chromatographic methods. It is thus very important that these methods have negligible environmental impact. Chromatographic techniques have the potential to be greener at all steps of the analysis, from sample collection...
-
Ionization and fragmentation of furan molecules by electron collisions
PublicationCation mass spectra obtained by electron impact were measured to investigate the ionization and ionic fragmentation of furan, C4H4O, molecules in the gas phase. The most abundant cations, with comparable intensities in the mass spectra, were the parent, C4H4O+, cation (68 amu) and the C3H3+ fragment (39 amu). The appearance energies of most of the observed ionic fragments were determined and the possible fragmentation processes...