displaying 1000 best results Help
Search results for: SMART ENGINEERING OF NEW MATERIALS
-
Modernization of the Trailer for Tyre/Road Rolling Resistance Measurements
PublicationIn the article the ways of defining tyre rolling resistance are presented. The advantages of the laboratory tests of tyre/road rolling resistance and the advantages and disadvantages of on the road tyre/road rolling resistance tests are described. The description of the special trailer used for tyre/road rolling resistance measurements designed and constructed in the Faculty of Mechanical Engineering at Gdansk University of Technology,...
-
Relieving the Measuring System of the Trailer for Tyre/Road Rolling Resistance Measurements from the Inertia Force
PublicationIn the article the principle of measuring of tyre/road rolling resistance tyres in road conditions applied in a special measuring trailer is presented. This trailer was built in Faculty of Mechanical Engineering at Gdansk University of Technology. The construction of two special devices used in this trailer was discussed. These devices eliminate the influence of some chosen confounding measurements factors such as: the inertia...
-
Shaft Misalignment Influence on Water Lubricated Turbine Sliding Bearings with Various Bush Modules of Elasticity
PublicationW artykule przeanalizowano wpływ wielkości przenoszenia osi wału względem panwi na nośność łożyska. Analizie poddano łożyska z odmiennymi rodzajami panwi o różnej sztywności.
-
Novel Design of an Ocean Wave Power Device
PublicationW artykule przedstawiono nowoczesną boję energetyczną o opatentowanej konstrukcji. Omówiono jej konstrukcję oraz przedstawiono problemy konstrukcyjne i badawcze. W ostatniej części artykułu przedstawiono wyniki badań wykonanych na modelu w basenie modelowym.
-
The Influence of Gas Mixture in the Glow-Discharge Nitriding Process of Austenitic Stainless Steel on Characteristic of Nitrided Cases
PublicationAustenitic stainless steels characterize with excellent corrosion resistance, although low mechanical properties. In many cases that limits their exploitation in industrial applications. Moreover, austenitic stainless steel is susceptible to local corrosion in the presence of halide ions. In present works, it was emphasized that the nitriding of austenitic stainless steels gives some potential abilities to obtain beneficial effect...
-
Compensation of pressure peaks in pwk-type hydraulic pumps
Publicationhydraulic axial pumps equipped with cam-driven commutation unit (pwk pumps) proved their high efficiency up to 55 mpa and ability to work self-sucking, even at high speed. displacement of pwk pump may easily be changed by moving its control cam. full discharge from hydrostatic forces makes such control possible by direct action of a low-energy actuator like proportional electromagnet or stepping motor. that eliminates heavy and...
-
A role of destructive and non-destructive tests in creep damage Identification
PublicationPrzedstawiono wyniki badań mjących zilustrować i określić rolę badań niszczących i nieniszczących w identyfikowaniu degradacji po pełzaniu
-
Guided waves in steel rails - experimental works and wavelet signal processing
PublicationW artykule zaprezentowano analizę falkową pomierzonych eksperymentalnie fal sprężystych wzbudzanych w szynach kolejowych.
-
Experimental verification and comparison of mode shape-based damage detection methods
PublicationW pracy przedstawiono wynik badań eksperymentalnych dotyczących oceny dokładności znanych z literatury metod detekcji uszkodzeń konstrukcji wykorzystujących zmiany jej parametrów modalnych. Pomiary wykonano wykorzystując skaner laserowy firmy Polytec. Omówiono sposoby poprawy jakości uzyskiwanych wyników, oraz zaproponowano własną metodę detekcji uszkodzeń wykorzystującą pomiar postaci i częstości drgań własnych konstrukcji.
-
Transmission and reflection coefficients for damage identification in 1D elements
PublicationW pracy przedstawiono mozliowści wykorzystania współczynnika odbicia i przejścia fali sprężystej w miejscu nieciągłości konstrukcji do identyfikacji jej rodzaju
-
The Research into the Effect of Conditions of Combined Electric Powered Diamond Processing on Cutting Power
Publication -
Analysis and Comparison of Safety of Children and Adult Passenger in Car Based on Crash Tests Results
Publication -
Numerical Simulation of Temperature Field in Steel under Action of Electron Beam Heating Source
Publication -
New Satellite Pumps
Publication -
Integrated Quality Ensuring Technique of Plasma Wear Resistant Coatings
Publication -
Use of Neural Networks in Diagnostics of Rolling-Element Bearing of the Induction Motor
Publication -
Experimental Study on Pounding between Structures during Damaging Earthquakes
PublicationMutual pounding between structures during earthquakes may cause serious structural damage. The aim of this paper is to show the results of a shaking table experimental study focused on pounding between structures in series under several earthquake excitations. The experiments were performed using three tower models with different configurations and different gap distances between them. In the first stage of the study, one rigid...
-
Enhancing the Seismic Resistance of Columns by GFRP Confinement Using Flexible Adhesive-Experimental Study
PublicationIn this paper, the results of two experiments, focused on testing the effectiveness of a method of enhancing the seismic (dynamic) resistance of masonry columns with the use of flexible polymer adhesive, are shown. The first experiment was devoted to investigate the damping properties of a polymer working between two stiff layers, whereas the aim of the second one was to verify if the identified damping properties of the polymer...
-
To what extent can hyperelastic models make sense the effect of clay surface treatment on the mechanical properties of elastomeric nanocomposites?
PublicationThe poor knowledge about nonlinear mechanical behavior of elastomer nanocomposites arises from the incomplete information on the interface. Application of hyperelastic models provides more insights into the nature and the situation of interaction between the elastomeric matrix and nanofillers. The current work seeks to address the effect of interphase strength on tensile properties of the elastomer nanocomposites under large deformations....
-
Diffusible Hydrogen Control in Flux Cored Arc Welding Process
PublicationOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper an experimental...
-
Free convection of water-Al2O3 nanofluid from horizontal porous coated tube
PublicationNanofluids are expected to enhance heat transfer in many thermal systems. Present efforts are concentrated on boiling heat transfer of nanofluids, although single phase convection is of key importance in various appliances such as car radiators or heating systems. This paper presents experimental results of heat transfer during free convection of water-Al3O3 nanofluid from horizontal tube covered with metallic porous coating. Contrary...
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublicationThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Damage-involved response of two colliding buildings under non-uniform earthquake loading
PublicationPounding between insufficiently separated buildings, which may result in considerable damage or may even lead to the total collapse of colliding structures, has been repeatedly observed during earthquakes. Earthquake-induced collisions of buildings has been intensively studied applying various structural models. It was assumed in the analyses, however, that the seismic excitation is identical for all structural supports; whereas,...
-
Generative Process Planning with Reasoning based on Geometrical Product Specification
PublicationThe focus of this paper is on computer aided process planning for parts manufacture in systems of definite process capabilities, involving the use of multi-axis machining centers for parts shaping and grinding machines for finishing. It presents in particular a decision making scheme for setup determination as a part of generative process planning. The planning procedurę consists of two stages. The first stage is associated with...
-
On Software Unit Testing For Improving Security And Performance Of Distributed Applications
PublicationPerformance and security are software (SW) application attributes situated on the opposite corners of system design. In the most drastic example the most secure component is the one totally isolated from the outside world, with communication performance reduced to zero level (e.g. disconnected physically from the network, placed inside a Faraday cage to eliminate possible wireless accessibility). On the other hand the most performance-optimized...
-
Carbon dioxide potential reduction using Start-Stop system in a car
PublicationOperating fuel consumption increases significantly when the vehicle stops frequently while driving or when the engine is idling during braking. In such cases, the internal combustion engine consumes the fuel but the mechanical energy is not used by the drive system. The amount of fuel that is consumed in this time by the engine can potentially be saved if the car is equipped with a Stop-Start system. Start-Stop system automatically...
-
Effect of surface roughness on thermal-hydraulic characteristics of plate heat exchanger
PublicationIn the paper the experimental analysis of passive heat transfer intensification in the case of modeled plate heat exchanger is conducted. The plate heat exchanger is chosen for the analysis because this kind of heat exchangers could be prospectively applied in the ORC systems, however other areas or application are equally possible. The experimental setup was assembled at the Department of Energy and Industrial Apparatus of Gdansk...
-
Frequency response spectra applied to assess efficiency of the training techniques
PublicationThe purpose of the research is to assess the increase of the muscle strength and power. Movement of the human body when the moving one impacts a stationary or moving body is taken under consideration. The waveform produced by an impact is transformed into frequency domain. The acceleration record is transformed as a complex spectrum, by the use of a Discrete Fourier Transformation. In this paper the applications of the discrete...
-
Organic Rankine as bottoming cycle to a combined Brayton and Clausius-Rankine cycle
PublicationThis paper presents an enhanced approach, as it will be considered here that the ORC installation could be extra-heated with the bleed steam, a concept presented by the authors. In such way the efficiency of the bottoming cycle can be increased and an amount of electricity generated increases. A thermodynamic analysis and a comparative study of the cycle efficiency for a simplified steam cycle cooperating with ORC cycle will be...
-
The analysis of turbine propulsion systems in nuclear submarines
PublicationThe article systematises submarines, which are presently in service, according to their propulsion types (both conventional and nuclear), power output, and submersion depth. Contemporary types of propulsion systems installed and used in submarines are discussed. Calculations were performed for the PWR (Pressurized Water Reactor) type nuclear propulsion system and the supercritical turbine propulsion system (supercritical reactor...
-
The initial selection of parameters for dynamic brake for car engine test dynamometer
PublicationThe article presents an analysis of the car engine loads. The aim of the analysis was to determine the parameters of the brake / electric motor on an engine test bad. Analysis of loads on the driving tests concerned on chassis dynamo to simulate them on an engine dynamometer. To check the range of dynamometer shaft angular acceleration inertial mass of a car was reduced on the crankshaft axis. The calculations of maximum shaft...
-
A New Technique of Spine Disease Treatment Supported by ADRSK1 Device
Publication -
Problems of analytical determination of journal bearing bush fatigue strength estimates
PublicationProblems connected with determination of stress distribution in sliding layer of thinwalled bearing bushes, investigated in bearing fatigue test rigs, have been presented. Using an example of plain bearings tested in the fatigue machine SMOK (built at the Gdask University of Technology) problems with obtaining a convergence of iterative procedure for determining the fatigue strength estimators of bearing alloy surface layer are...
-
Influence of design of hydraulic components on their operation in low ambient temperatures
PublicationW artykule przestawiono wpływ konstrukcji zespołów hydraulicznych na ich działanie w niskich temperaturach otoczenia.
-
Experimental Investigation of Prototype Water-Lubricated Compliant Foil Bearings
PublicationPraca zawiera wyniki badań doświadczalnych prototypowego łożyska foliowego smarowanego wodą. Łożyska tego typu mogą mieć zastosowanie w węzłach, od których wymaga się ekologicznego środka smarowego, np. pompy wodne czy turbiny wodne. W opracowaniu zademonstrowano wyniki badań trzech prototypowych poprzecznych łożysk foliowych. Opisano napotkane problemy badań oraz wprowadzonych do konstrukcji łożyska zmian, których celem była poprawa...
-
Numerical analysis of crack propagation in silicone nitride
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculation...
-
Numerical Analysis of a Steel Frame Building with Soft-storey Failure under Ground Motion Excitation
PublicationThe aim of this paper is to show the results of a numerical analysis focused on the behaviour of multi-storey steel frame building that suffers from a soft-storey failure under ground motion excitation. A numerical model of the structure was created in FEM computer software and was exposed to an impact that would have been generated after a soft-storey failure due to falling of the upper floors. During the analysis, the whole structure...
-
Diagnosis of Damage in a Steel Tank Model by Shaking Table Harmonic Tests
PublicationThe aim of the present paper is to show the results of the shaking table experimental study concerning the diagnosis of damage in a model of cylindrical steel tank with self-supported roof which is filled with liquid. During the tests, the base of the structure was excited under the harmonic loading with variable frequency. The tests were repeated for different stages of damage, which was introduced in the model by easing the bolts...
-
Shaking table experimental study on diagnosis of damage and its evaluation in steel structure
PublicationCelem artykułu jest pokazanie wyników badań eksperymentalnych przeprowadzonych na stole sejsmicznym dotyczących identyfikacji uszkodzeń modelu dwukondygnacyjnej konstrukcji stalowej. Uszkodzenie zdefiniowano poprzez spadek sztywności i symulowano poprzez zamianę słupów modelu na elementy o mniejszym przekroju poprzecznym. Wyniki badań pokazują charakterystyczny spadek wartości naturalnych częstotliwości konstrukcji wraz ze wzrostem...
-
Inelastic damage-involved response of colliding buildings during earthquakes
PublicationW artykule poddano analizie nieliniowe zachowanie się kolidujących ze sobą budynków powodujące ich uszkodzenie podczas trzęsień ziemi. Analiza dotyczy zderzeń pomiędzy dwoma sąsiednimi budynkami czterokondygnacyjnymi. Badania pokazują, iż zastosowanie nieliniowego modelu numerycznego zachowania się obu budowli podczas trzęsień ziemi ma duże znaczenia dla dokładności wyników.
-
Damage-Involved Structural Pounding in Bridges under Seismic Excitation
PublicationDuring severe earthquakes, pounding between adjacent superstructure segments of highway elevated bridges was often observed. It is usually caused by the seismic wave propagation effect and may lead to significant damage. The aim of the present paper is to show the results of the numerical analysis focused on damage-involved pounding between neighbouring decks of an elevated bridge under seismic excitation. The analysis was carried...
-
Laser Surface Treatment of Sintered Stainless Steels for Wear Resistance Enhancement
Publication -
Formability and microstructure evolution mechanisms of Ti6Al4V alloy during a novel hot stamping process
Publication -
The Rolling Contact Fatigue of PVD Coated Spur Gears
Publication -
The Effect of Temperature on Wear Mechanism of the AlCrN Coated Components
Publication -
Removal of Dyes from the Environment by Adsorption Process
Publication -
Tribological Behaviour of Copper-Graphene Composite Materials
Publication -
The Scuffing Resistance of WC/C Coated Spiral Bevel Gears
Publication -
Detection of delamination in multi layer composite beams.
PublicationW pracy przedstawiono model belki kompozytowej z delaminacją. Omówiono czynniki propagacji fali sprężystej w belce i możliwości wykorzystania zmian w propagującej fali wywołanych delaminacją do jej detekcji.
-
Mathematical Modelling of a Seismic Isolation System to Protect Structures During Damaging Earthquakes
PublicationThe present study aims to determine the effectiveness of a nonlinear mathematical model in simulating complex mechanical behaviour of a seismic isolation system to protect structures during strong and damaging earthquakes. In order to construct the Polymeric Bearings considered in this research, a specially prepared flexible polyurethane elastomer with increased damping properties has been used. The usefulness of the proposed mathematical...