Search
displaying 1000 best results Help
Search results for: NEGATIVE FEEDBACK LOOP
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - DISTILLED WATER. Specim. set K02
Open Research DataFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DISTILLED WATER. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). No lubrication (DRY). Specim. set K03
Open Research DataFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DRY. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate folders).Specimen...
-
Semi-adaptive feedback active control of MRI noise
PublicationA feedback controller is proposed for cancellation of magnetic resonance imaging (MRI) noise. The design of the controller takes into account specific features of the MRI noise signal. Simulation results show that a considerable rejection rate of the MRI noise can be obtained.
-
Uncertainty estimation of loop impedance measurement determined by the vector method
PublicationThis article presents a detailed analysis of uncertainty estimation of loop impedance measurement determined by the vector method. The analysis includes the following estimates: resistance variance, voltage variance and time measurement variance. This paper presents a methodology for estimating the combined standard uncertainty of loop impedance by the vector method. The vector method allows to determine loop impedance based on...
-
Robust algorithm for active feedback control of narrowband noise
PublicationThe problem of active control of narrowband acoustic noise is considered. It is shown that the proposed earlier feedback control algorithm called SONIC (self-optimizing narrowband interference canceller), based on minimization of the L2-norm performance measure, can be re-derived using the L1 approach. The resulting robust SONIC algorithm is more robust to heavy-tailed measurement noise, such as the αlpha-stable noise, than the...
-
Synthesis of a state feedback controller for an averaging tank with variable filling
PublicationIn paper, a nonlinear averaging tank with variable filling is considered. The main purpose of this research work was the modelling and control system synthesis of an averaging tank. The control objectives included ensuring stability and zero steady-state error of the system and achieving settling time as short as possible, while maintaining a minimal overshoot. In order to achieve the intended purpose, firstly a mathematical model...
-
Stable indirect adaptive control based on discrete-time T-S fuzzy model
PublicationThis paper presents an indirect adaptive fuzzy control scheme for uncertain nonlinear asymptotically stable plants.A discrete-time T-S fuzzy input-output model is employed to approximate the unknown plant dynamics. The T-S fuzzy model is fed with its own states, which are indeed its past outputs, rather than the measurements from the plants. Entirely based on this model, a feedback linearization control law is designed by using...
-
Stable indirect adaptive control based on discrete-time T-S fuzzy model
PublicationThis paper presents an indirect adaptive fuzzy control scheme for uncertain nonlinear asymptotically stable plants.A discrete-time T-S fuzzy input-output model is employed to approximate the unknown plant dynamics. The T-S fuzzy model is fed with its own states, which are indeed its past outputs, rather than the measurements from the plants. Entirely based on this model, a feedback linearization control law is designed by using...
-
The Crowd as a Source of Knowledge - From User Feedback to Fulfilling Requirements
PublicationCrowd-based and data-intensive requirements engineering (RE) strategy is an approach for gathering and analyzing information from the general public or the so-called crowd to derive validated user requirements. This study aims to conceptualize the process of analyzing information from a crowd to achieve the fulfillment of user requirements. The created model is based on the ADO framework (Antecedents-Decisions-Outcomes). In the...
-
Active vibration reduction with a use of enegry performance index at acceleration feedback
PublicationW pracy przedstawiono wyniki badań eksperymentalnych i symulacji w trybie Hardware-in-the-loop nowego algorytmu aktywnej redukcji drgań. Algorytm ten bazuje na energetycznym wskaźniku jakości zmodyfikowanym w ten sposób, że wykorzystuje bezpośrednio sygnał sprzężenia zwrotnego przyspieszeń.
-
Power Hardware-in-the-Loop Approach In Power System Development
PublicationThe main objective of the research is the verification of the Power Hardware-In-The-Loop (PHIL) approach in power system analysis and design. The premise of the article is that using PHIL approach the performance of the power system in steady and transient state conditions can be analysed in real power system conditions. Models of induction machine were developed and real time simulations were performed. Simulation variables were...
-
Exploration of Creativity Techniques in Software Engineering in Training-Application-Feedback Cycle
PublicationCreativity research has proposed about a hundred and fifty creativity techniques. The question is whether they can be applied in software engineering for creativity training or directing creativity in software projects. This paper aims at answering this question via a quasi-experiment conducted in Training-Application-Feedback cycle in which participants express their opinions about selected creativity techniques after training...
-
Investigation of the influence of capilary effect on operation of the loop heat pipe
PublicationIn the paper presented are studies on the inestigation of the capillary forces effect inducted in the porous structure of a loop heat pipe using water and ethanol ad test fluids. The potential application of such effects is for example in the evaporator of the domestic micro-CHP unit, where the reduction of pumping power could be obtained. Preliminary analysis of the results indicates water as having the best potential for developing...
-
Identifying and Mitigating the Negative Effects of Power in Organizations
PublicationThis article investigates the possible negative effects of power in organizations. It demonstrates how holding power may affect an individual’s perception of others, actions, and cognition. Ways in which power may have a detrimental effect on different aspects of a manager’s functioning within an organization, including building relationships, communication, and performance are analyzed. It is argued that individuals are unaware...
-
Design of optimal state feedback controller with observer for multidimensional electrical system
PublicationFrom the control point of view, two-input-two-output RC electrical system is a linear and multidimensional system. In this paper, integral control and closed-loop observer are verified whether they can be used and designed. To verify this, Kalman tests are made. These structures are presented and discussed. Integral Control is tested with some base disturbances impact and checked whether it can handle them. The estimated values...
-
Fault Loop Impedance Measurement in Circuits Fed by UPS and Principle of Safety Protection
PublicationThis paper indicates a significant problem of uncertainty of fault loop impedance (FLI) measurement in circuits powered from uninterruptible power supply (UPS) (double-conversion AC-DC-AC). The correctly determined value of this impedance, related to the short-circuit current disconnection time and to the reference value, is one of the most important elements that determines the approval of an electrical installation and its receivers...
-
What matters most to patients? On the Core Determinants of Patient Experience from Free Text Feedback
PublicationFree-text feedback from patients is increasingly used for improving the quality of healthcare services and systems. A major reason for the growing interest in harnessing free-text feedback is the belief that it provides richer information about what patients want and care about. The use of computational approaches such as structural topic modelling for analysing large unstructured textual data such as free-text feedback from patients...
-
Feedback control of water quality
PublicationSformułowano problem sterowania jakością wody w sieciach wodociągowych i następnie zaproponowano podejście do projektowania sterowania stężeniem chloru w takich sieciach, bazujący na estymacji parametrów oraz sterowaniu adaptacyjnym. Podejście wykorzystuje założenie, że w sieci wodociągowej istnieją punkty wstrzykiwania chloru. Zależność typu wejście-wyjście pomiędzy stężeniem chloru w węźle dozowania i monitorowania jest modelowana...
-
Keystroke Dynamics Patterns While Writing Positive and Negative Opinions
PublicationThis paper deals with analysis of behavioural patterns in human–computer interaction. In the study, keystroke dynamics were analysed while participants were writing positive and negative opinions. A semi-experiment with 50 participants was performed. The participants were asked to recall the most negative and positive learning experiences (subject and teacher) and write an opinion about it. Keystroke dynamics were captured and...
-
Loop-mediated isothermal amplification (LAMP) as a diagnostic tool in detection of infectious diseases
PublicationLoop-mediated isothermal amplification (LAMP) is a gene amplification method which amplifies DNA with high specificity and efficiency under isothermal conditions. Because of its rapidity and simplicity, it is a valuable diagnostic tool in the early detection and identification of infectious diseases. LAMP method is based on the use of a set of four to six specially designed primers spanning six to eight distinct sequences on the...
-
Impact of digital signal processing on FOC current feedback in high-speed PMSM drive
PublicationIn applications where size and weight of the electric motor are among major design concerns, Permanent Magnet Synchronous Motors (PMSMs) with wide operational speed-range are commonly preferred. Due to limited inverter switching frequency, high-speed operation of a drive results in a low ratio between the switching frequency and the fundamental frequency of motor voltage. Such operating conditions have been recently identified...
-
Closed-loop stimulation of temporal cortex rescues functional networks and improves memory
PublicationMemory failures are frustrating and often the result of ineffective encoding. One approach to improving memory outcomes is through direct modulation of brain activity with electrical stimulation. Previous efforts, however, have reported inconsistent effects when using open-loop stimulation and often target the hippocampus and medial temporal lobes. Here we use a closed-loop system to monitor and decode neural activity from direct...
-
Tailoring Graphene to Achieve Negative Poisson's Ratio Properties
PublicationGraphene can be made auxetic through the introduction of vacancy defects. This results in the thinnest negative Poisson's ratio material at ambient conditions known so far, an effect achieved via a nanoscale de-wrinkling mechanism that mimics the behavior at the macroscale exhibited by a crumpled sheet of paper when stretched.
-
Adaptive Optimal Discrete-Time Output-Feedback Using an Internal Model Principle and Adaptive Dynamic Programming
PublicationIn order to address the output feedback issue for linear discrete-time systems, this work suggests a brand-new adaptive dynamic programming (ADP) technique based on the internal model principle (IMP). The proposed method, termed as IMP-ADP, does not require complete state feedback, merely the measurement of input and output data. More specifically, based on the IMP, the output control problem can first be converted into a stabilization...
-
A new method of fault loop resistance measurement in low voltage systems with residual current devices
PublicationThis paper presents a new method of fault loop resistance measurement in low voltage systems with residual current devices. The method enables measuring fault loop resistance without nuisance tripping of residual current devices, by application an unconventional waveform of measurement current. It is important for proper verification of the effectiveness of protection against electric shock.
-
Flow Boiling in Minigap in the Reversed Two-Phase Thermosiphon Loop
PublicationThe paper presents the results of experimental investigations of a model of a heat exchanger featuring a minigap, which is perceived as an evaporator for an inverted thermosiphon. The system works with a single component test fluid. The tested evaporator generates pumping power in the test loop in a way similar to the mammoth pump. The tests regarded a module of the heat exchanger, consisting of a hot leg and a cold leg with the...
-
Recent Advances in Loop Heat Pipes with Flat Evaporator
PublicationThe focus of this review is to present the current advances in Loop Heat Pipes (LHP) with flat evaporators, which address the current challenges to the wide implementation of the technology. A recent advance in LHP is the design of flat-shaped evaporators, which is better suited to the geometry of discretely mounted electronics components (microprocessors) and therefore negate the need for an additional transfer surface (saddle)...
-
Mapping negative unintended consequences of disruptive technologies use in smart cities
PublicationSmart cities governance (SCG) consists of both to foster technology-enabled innovation, and to utilize disruptive technologies (DT) outcomes and impacts to increase public value of urban services. Despite widespread discussion of DT benefits, scientific literature identifies multiple determinants of unintended negative consequences (UC) of DT deployment in smart city initiatives. By considering UC as the negative aspects resulting...
-
Evaluation of applicability of classic methods of a fault loop impedance measurement to circuits with residual current devices
PublicationMeasurement of fault loop impedance in low voltage grids and systems is in most cases performed to verify the effectiveness of protection against electric shock by automatic disconnection of supply. For the sake of measurement accuracy, it is advisable to perform it using large current. Unfortunately, in circuits with residual current devices which are very widely used nowadays, a large measurement current may trigger those devices...
-
Millimeter Wave Negative Refractive Index Metamaterial Antenna Array
PublicationIn this paper, a novel negative refractive index metamaterial (NIM) is developed and characterized. The proposed metamaterial exhibits negative effective permittivity (εeffe) and negative effective permeability (µeffe) at millimeter wave frequency of 28GHz. This attractive feature is utilized to enhance the gain of a microstrip patch antenna (MPA). Two thin layers of 5 5 subwavelength unit cell array of NIM are placed above a...
-
Selected problems of earth fault loop impedance testing in circuits fed from UPS
PublicationIn the paper a principle of earth fault loop impedance testing in low voltage systems has been presented. Selected factors, influencing accuracy of the testing, are indicated. A structure of UPS of VFI-type and the problem of impedance testing in circuits with such type of UPS are discussed.
-
Vibration surveillance supported by Hardware-In-the-Loop Simulation in milling flexible workpieces
PublicationW artykule przedstawiono nowoczesne podejście do problemu minimalizacji poziomu drgań podczas frezowania szybkościowego elementów podatnych. Do analizy dynamicznej procesu skrawania zastosowano niestacjonarny model opisany we współrzędnych hybrydowych. Na tej podstawie, przy wykorzystaniu energetycznego wskaźnika jakości wyprowadzono opis sygnału sterującego. Sygnał ten jest następnie stosowany do aktywnej redukcji drgań przedmiotu...
-
Journal of Pharmaceutical Negative Results
Journals -
Journal of Negative Results in BioMedicine
Journals -
Feedback Control of Doubly-Fed Generator Connected to Current Source Converter
PublicationDoubly-fed induction generator (DFIG) system supplied by current source converter (CSC) is considered in this article. The DFIG can work in two independent modes: AC grid connection and stand-alone mode. The DFIG is connected to the ac grid directly through its stator and the CSC links the rotor side. In this mode, the active and reactive powers of the DFIG must be controlled. This article proposes two control system structures...
-
D-loop sequences retrieved from Canis lupus familiaris mitochondrial genome
Open Research DataCanine mitochondrial genome is built of 16727 bp. Non-coding control region (mtCR), called also D-loop, begins with 15458 nucleotide and ends with 16727 nucleotide. The length of this fragment is 1270 bp (Kim et al., 1998). D-loop region is responsible for replication and transcription of mitochondrial DNA. Mutations that occur within it may cause irregularity...
-
A method of earth fault loop impedance measurement without unwanted tripping of RCDs
PublicationIn low-voltage networks, earth fault loop impedance (EFLI) measurement is the basis for assessing the effectiveness of automatic disconnection of supply. Such a measurement is performed during initial and periodical verification, especially in a TN low-voltage network. Nowadays, due to widespread application of residual current devices (RCDs), such test is difficult in many circuits because RCDs operate during the test. In this...
-
MRAS-Based Switching Linear Feedback Strategy for Sensorless Speed Control of Induction Motor Drives
PublicationThis paper presents a newly designed switching linear feedback structure of sliding mode control (SLF-SMC) plugged with an model reference adaptive system (MRAS) based sensorless fieldoriented control (SFOC) for induction motor (IM). Indeed, the performance of the MRAS depends mainly on the operating point and the parametric variation of the IM. Hence, the sliding mode control (SMC) could be considered a good control alternative...
-
A mobile loop order–disorder transition modulates the speed of chaperonin cycling
PublicationMolecular machines order and disorder polypeptides as they form and dissolve large intermolecular interfaces, but the biological significance of coupled ordering and binding has been established in few, if any, macromolecular systems. The ordering and binding of GroES co-chaperonin mobile loops accompany an ATP-dependent conformational change in the GroEL chaperonin that promotes client protein folding. Following ATP hydrolysis,...
-
Comparison of state feedback and PID control of pressurizer water level in nuclear power plant
PublicationThe pressurizer water level control system in nuclear power plant with pressurized water reactor (PWR) is responsible for coolant mass balance. The main control goal is to stabilize the water level at a reference value and to suppress the effect of time-varying disturbances (e.g. coolant leakage in primary circuit pipeline system). In the process of PWR power plant operation incorrect water level may disturb pressure control or...
-
Genetic Programming with Negative Selection for Volunteer Computing System Optimization
PublicationVolunteer computing systems like BOINC or Comcute are strongly supported by a great number of volunteers who contribute resources of their computers via the Web. So, the high efficiency of such grid system is required, and that is why we have formulated a multi-criterion optimization problem for a volunteer grid system design. In that dilemma, both the cost of the host system and workload of a bottleneck host are minimized. On...
-
A low-voltage CMOS negative impedance converter for analogue filtering applications
PublicationLow-voltage high-frequency continuous-time filters are still required in many applications and are the subject of continuing research. There are many techniques to realize integrated filters, including OTA C, Opamp RC and MOSFET-C-Opamp. The latter two show high dynamic range at low supply voltage, but their frequency operating range is usually limited to several megahertz. Transconductance filters are dedicated to higher frequencies....
-
Feedback control system for a miniaturized LMIS robot
PublicationReferat przedstawia sposób realizacji mechanizmu sprzężenia zwrotnego dla układu sterowania zestawów Lego Mindstorm Invention Systems. Obiektem sterowania jest układ ''wózek-wahadło''. Przedstawiono model matematyczny, wyniki badań eksperymentalnych dot. identyfikacji parametrów modelu, syntezę wybranych regulatorów oraz wyniki badań symulacyjnych układu sterowania pozycji i kąt wychylenia wahadła. Przedstawiono także sposób wykonania...
-
Optimal state feedback controller for balancing cube
PublicationIn this paper, a nonlinear balancing cube system is considered, the concept for which is based on an inverted pendulum. The main purpose of this work was the modelling and construction of a balancing cube with the synthesis of the control system. The control objectives included swing-up and stabilization of the cube on its vertex at an unstable equilibrium. Execution of the intended purpose required, first, deriving a cognitive...
-
Simulation of the Remanence Influence on the Transient States of the Single-Phase Transformer Including Feedback Preisach Model
PublicationThis paper presents the results of the experimental and simulation investigation concerning the influence of remanence in the core of a single-phase transformer at the no-load transient state. Experimental studies consisted of the discharge of the capacitor through the primary winding at several different values of the residual magnetic flux. The paper presents a model of the transformer test system, taking into account the magnetic...
-
Experimental verification of a new method of loop resistance testing in low voltage systems with residual current devices
PublicationA periodical verification of the effectiveness of protection against electric shock shall be performed in low voltage systems. The scope of this verification includes loop impedance/resistance testing. If a residual current device is installed in a tested circuit, this testing is problematic. A residual current device trips out during the test, because of the high value of measurement current. This precludes the execution of the...
-
Power Hardware-In-the-Loop Approach for Autonomous Power Generation System Analysis
PublicationThe article presents the Power Hardware-In-the-Loop (PHIL) dynamic model of a synchronous generator of 125 kVA for autonomous power generation system analysis. This type of system is typically composed of electrical energy sources in the form of several diesel generator units with synchronous machines, the main distribution switchboard and different loads. In modern power distribution systems, the proposed power management strategies...
-
The mediational role of future and past time perspectives in the relationship between negative affectivity and sense of coherence
PublicationSense of coherence (SoC) can promote positive coping, and one of its most prominent negative correlates is negative affectivity (NA). In the current study, we hypothesized that future and past time perspectives (TPs) will mediate the relationship between sense of coherence and negative affectivity, and the inverse relationship. The study was questionnaire-based, performed online. N = 719 participants aged 25-45 from...
-
Stability Analysis of Shunt Active Power Filter with Predictive Closed-Loop Control of Supply Current
PublicationThis paper presents a shunt active power filter connected to the grid via an LCL coupling circuit with implemented closed‐loop control. The proposed control system allows selective harmonic currents compensation up to the 50th harmonic with the utilization of a model‐based predictive current controller. As the system is fully predictive, it provides high effectiveness of the harmonic reduction, which is proved by waveforms achieved...
-
Prioritising national healthcare service issues from free text feedback – A computational text analysis & predictive modelling approach
PublicationPatient experience surveys have become a key source of evidence for supporting decision-making and continuous quality improvement within healthcare services. To harness free-text feedback collected as part of these surveys for additional insights, text analytics methods are increasingly employed when the data collected is not amenable to traditional qualitative analysis due to volume. However, while text analytics techniques offer...