Search
Search results for: PETROLEUM
-
Shiyou Xuebao, Shiyou Jiagong/Acta Petrolei Sinica (Petroleum Processing Section)
Journals -
Correlation between performance properties of asphalt mixes and properties of bituminous binder.
PublicationPrzeprowadzono badania betonów asfaltowych, gdzie zmienną był tylko rodzaj asfaltu. W badaniach określono podstawowe cechy asfaltów. Dla betonów asfaltowych badano takie właściwości jak: odporność na deformacje trwałe, odporność na starzenie, odporność na działanie wody i mrozu oraz właściwości niskotemperaturowe. Wynikiem analiz są przedstawione w referacie najbardziej skorelowane cechy asfaltu z właściwościami betonu asfaltowego.
-
Zhongguo Shiyou Daxue Xuebao (Ziran Kexue Ban)/Journal of China University of Petroleum (Edition of Natural Science)
Journals -
An improved scalable method of isolating asphaltenes
PublicationA new, improved and scalable procedure of asphaltene fraction isolation is presented and compared to standard test methods. The new procedure uses 1:40 feedstock to solvent (n-heptane) ratio (g/mL), filtration through a cellulosic thimble and extensive washing in a Soxhlet type extractor. The group type composition and purity of the asphaltene fractions have been examined using thin-layer chromatography with flame-ionization detection....
-
Aiding (opponent) flow of hybrid copper–aluminum oxide nanofluid towards an exponentially extending (lessening) sheet with thermal radiation and heat source (sink) impact
Publication -
The effect of paleo-environment on hydrocarbon generation potential: Example from Vaca Muerta Formation, Neuquén Basin, Argentina
PublicationA 137-m continuous core from the Jurassic-Early Cretaceous marine derived oil shale with the maturity Ro about 0.7 %, representing the oil window in the Vaca Muerta Formation, Neuquén Basin, Argentina, was examined using geological, mineralogical, petrographic, and geochemistry techniques. Three distinct intervals were identified within the core: the upper carbonate-rich section with intense bioturbation, indicating dysoxic to...
-
Natalia Anna Wójcik dr hab. inż.
People -
Dimethyl ether (DME) as potential environmental friendly fuel
PublicationIn recent years, there has been a growing interest in replacing petroleum fuels with so-called second generation environmental friendly fuels. Compared to traditional petroleum fuels dimethyl ether (DME) could be used as a clean high-efficiency compression ignition fuel with reduced particulate matter (PM), sulfur oxides (SOx), hydrocarbons (HC), carbon monoxide (CO) as well as combustion noise. Compared to some of the other leading...
-
Ecological and Health Effects of Lubricant Oils Emitted into the Environment
PublicationLubricating oils used in machines with an open cutting system, such as a saw or harvester, are applied in forest areas, gardening, in the household, and in urban greenery. During the operation of the device with an open cutting system, the lubricating oil is emitted into the environment. Therefore, the use of an oil base and refining additives of petroleum origin in the content of lubricants is associated with a negative impact...
-
Environmental impact and industrial development of biorenewable resources for polyurethanes
PublicationPolyurethanes are among the most developed types of polymers. They are produced from the three primary components, i.e., polyols, low-molecular-weight glycols used as chain extenders, and diisocyanates. Until recently, all these substrates have been obtained via petrochemical processes. A decrease in petroleum-based resources and new ecological trends in chemistry, chemical technology, and materials engineering have generated increasing...
-
Degradation of the Concrete Railway Track Bed Located in the Vicinity of the Loading Wharf
PublicationThe following article describes the damages of the concrete railway track bed at the place of unloading petroleum products located in the immediate vicinity of the cargo berth. The concrete of the track bed has been a subject to degradation as a result of many years of exploitation resulting, inter alia, in its cyclical flooding of petroleum products during the unloading and loading of rail tankers. Repairs carried out in the previous...
-
Application of Diagnostic Ratios of PAHs to Characterize the Pollution Emission Sources
PublicationThe paper summarizes the potential of application of parent polycyclic aromatic hydrocarbons (PAHs) to identify their emission sources. Four parent PAHs diagnostic ratios are used for this purpose: anthracene/(anthracene + phenanthrene), fluoranthene/(fluoranthene + pyrene), benzo[a]pyrene/(benzo[a]pyrene + chryzene) and indeno[1,2,3-c,d]pyrene/(indeno[1,2,3-c,d]pyrene + benzo[g,h,i]perylene). The compounds of each ratio have the...
-
Determination of total mercury in raw petrol using cold vapour atomic absorption spectrometry
PublicationPresence of different forms of mercury in petroleum based products may impair the proper operation of the equipment or led to poisoning of automotive catalysts. However much more important problem is environmental pollution with mercury emitted from different types of fossil fuels. Although the average mercury concentration in petroleum based products (automotive fuels) is on the level around 1 ppb, taking into account annual...
-
The influences of the information and communication technology on the structural changes of Japanese energy sectors from 1985 through 2005: a statistical analysis
PublicationThe purpose of this study is to analyse the influences of information and communication technology (ICT) on the structural changes of Japanese energy sectors from 1985-2005. In this study, ICT is represented by two explanatory variables, namely: 1) computers, main parts and accessories; 2) telecommunications equipment. We employ a statistical tool in investigating the influences quantitatively, namely constrained multivariate regression...
-
The Thin-Layer Microchromatography (μTLC) and TLC–FID Technique as a New Methodology in the Study of Lubricating Oils
PublicationThis paper concerns the possibility of using TLC coupled with a flame ionization detector (FID) and micro-TLC (μTLC) as precursors for microfluidized devices of analytical techniques to identify and determine the presence and content of the petroleum/vegetable oil base in the lubricating oils applied in cutting devices (chainsaws). This research is related to the problem of ensuring, in compliance with the requirements of environmental...
-
Low and high energy explosive materials used in shale gas recovery
PublicationNowadays the explosives are widely used in many areas of life, including industry and mining. A wide range of explosive materials is used in the petroleum industry - from low to high explosives. Recently, as the unconventional oil and gas production became possible, explosives are also found to be used in perforators during the pre-completion stage of the fracturing process. This paper presents literature on theoretical and practical...
-
Treatment of bitumen post oxidative effluents by sulfate radicals based advanced oxidation processes (S-AOPs) under alkaline pH conditions
PublicationSulfate radicals based Advanced Oxidation Processes (S-AOPs), namely Persulfate and peroxymonosulfate, were used for the treatment of post oxidative effluents from a production of petroleum bitumens under alkaline pH. Studies on the identification and monitoring of the volatile organic compounds (VOCs) along with COD, BOD and sulfide ions reduction were performed. Persulfate with a ratio between the oxygen from the oxidant and...
-
Effect of glycolysate obtained from polyurethane wastes on mechanical properties of rubber materials
PublicationThe paper presents the possibility of utilization of wastes from polyurethane foams. In this work the results of mechanical investigations of materials obtained from natural rubber mixtures with a mixture of glycolysate and biodiesel glycerine as a plasticizer are described. The measurements of mechanical properties showed rather good tensile strength, elongation at break and modules of extensions M100%, M200%, M300% of obtained...
-
PAH diagnostic ratios for the identification of pollution emission sources
PublicationPolycyclic aromatic hydrocarbon (PAH) diagnostic ratios have recently come into common use as a toolfor identifying and assessing pollution emission sources. Some diagnostic ratios are based on parentPAHs, others on the proportions of alkyl-substituted to non-substituted molecules. The ratios areapplicable to PAHs determined in different environmental media: air (gas þ particle phase), water,sediment, soil, as well as biomonitor...
-
Studies on Treatment of Bitumen Effluents by Means of Advanced Oxidation Processes (AOPs) in Basic pH Conditions
PublicationThe paper presents the results of studies on chemical treatment of effluents from production of bitumen of petroleum origin. Due to the presence of sulfide ions, the pH of these effluents is strongly alkaline. Several Advanced Oxidation Processes (AOPs) were studied, including the use of hydroxyl and sulfate radicals oxidants, the hydrodynamic cavitation as well as sonocavitation. The best processes allow to obtain 45% reduction...
-
Studies on treatment of bitumen effluents by means of Advanced Oxidation Processes (AOPs) in basic pH conditions
PublicationThe paper presents the results of studies on chemical treatment of effluents from production of bitumen of petroleum origin. Due to the presence of sulfide ions, the pH of these effluents is strongly alkaline. Several Advanced Oxidation Processes (AOPs) were studied, including the use of hydroxyl and sulfate radicals oxidants, the hydrodynamic cavitation as well as sonocavitation. The best processes allow to obtain 45% reduction...
-
DME as alternative fuel for compression ignition engines – a review
PublicationThe ecological issues and the depletion of crude oil, has led the researchers to seeking for non-petroleum based alternative fuels, along with more advanced combustion technologies, and after-treatment systems. The use of clean alternative fuels is the one of the most perspective method that aiming at resolving of the said issues. One of the promising alternative fuels that can be used as a clean highefficiency compression ignition...
-
Review of hydrogen production technologies for automotive sector – thermodynamic analysis of energy and exergy losses
PublicationFew recent years has shown that hydrogen technology has a good chance to replace petroleum technology in automotive sector. However, hydrogen in pure form practically does not occur on Earth. That is why H2 form is used only as an energy carrier and it must be produced using another source of energy form water or hydrocarbon fuels. In this paper short overview of hydrogen production technology has been presented, with energy and...
-
Modal analysis of cylindrical steel tanks
PublicationCylindrical steel tanks are very popular structures used for storage of products of chemical and petroleum industries. Their safety and reliability is crucial because any failure could have serious consequences. The aim of present paper is to show the results of the first phase of investigation of seismic behaviour such structures. Modal analysis using Finite Element Method (FEM) for three models of real tanks used in Poland has...
-
Experimental determination of dynamic properties of cylindrical steel tank model filled with liquid
PublicationIn technical branches, such as chemical or petroleum industries, cylindrical steel tanks are essential structures used for storage of liquid products. Any failure might have disastrous consequences, therefore their safety and reliability is essential. The aim of the present paper is to show the results of the experimental study which has been conducted on a scaled model of a real tank used in Poland. The investigation was carried...
-
A Comprehensive Review: Applications of the Kozeny–Carman Model in Engineering with Permeability Dynamics
PublicationIn this review article, we investigate the dynamic nature of the Kozeny–Carman Model concerning permeability and its application in engineering contexts. Providing insights into the changing dynamics of permeability within mining, petroleum, and geotechnical engineering, among other engineering applications. While some are complex and require additional modifcations to be applicable, others are simple and still function in specifc...
-
Environmental Risk Assessment of WWII Shipwreck pollution
PublicationThe pollution of the sea is a global problem that has arisen as a consequence of the industrialization of the world and the intense transportation of crude oil and the products of its refinement. As sailing vessels were replaced by motor propelled ships towards the end of the 19th century, a new source of sea water pollution came into being. Every emergency involving a tanker carrying crude oil and its products is a potential source...
-
Recent Advances in Development of Waste-Based Polymer Materials: A Review
PublicationLimited petroleum sources, suitable law regulations, and higher awareness within society has caused sustainable development of manufacturing and recycling of polymer blends and composites to be gaining increasing attention. This work aims to report recent advances in the manufacturing of environmentally friendly and low-cost polymer materials based on post-production and postconsumer wastes. Sustainable development of three groups...
-
Application of the corrosion tester in corrosion tests using the acoustic emission method.
PublicationThe article presents an innovative method of corrosion tests using the acoustic emission method and the corrosion tester. The problem of corrosion occurring in ballast tanks and tanks carrying petroleum products is discussed. The acoustic method is presented which, due to the use of a unique corrosion tester, is used to monitor the course of corrosion processes in steel. The principle of operation of the corrosion tester, its construction...
-
Response of a steel tank during earthquakes and mining tremors - experimental investigation
PublicationCylindrical steel tanks are very popular shell structures used to store the products of chemical and petroleum industries. Any failure might have disastrous consequences, therefore their safety and reliability is essential. Earthquakes are the most dangerous and also the most unpredictable dynamic loads acting on such structures. On the other hand, mining tremors are usually considered to be less severe due to lower acceleration...
-
Renewable natural resources as green alternative substrates to obtain bio-based non-isocyanate polyurethanes-review
PublicationCommercially available polyurethanes are synthesized by the polyaddition of diisocyanates with polyols and low molecular weight chain extenders. A new approach to polyurethanes synthesis is realized via non-isocyanate routes. Negative impacts of petroleum-based chemicals on the environment and human health as well as gradual reduction of fuel-based resources, which leads to an increase in their prices, are an incentive to looking...
-
THE IMPACT OF GROUND TIRE RUBBER TREATMENT ON THE THERMAL CONDUCTIVITY OF FLEXIBLE POLYURETHANE/GROUND TIRE RUBBER COMPOSITES
PublicationWaste car tires are burdensome waste, and their utilization is crucial for the natural environment. In many countries, the primary method of their recycling is energy recovery, performed by simple combustion. However, material recycling is much more effective and significantly more beneficial for the natural environment. It results in the generation of ground tire rubber, which can be used to produce polymerrubber composites. It...
-
Surface water quality assessment by the use of combination of multivariate statistical classification and expert information
PublicationThe present study deals with the assessment of surface water quality from an industrial-urban region located in northern Poland near to the city of Gdansk. Concentrations of thirteen chemicals includingtotal polycyclic aromatic hydrocarbons (PAHs), halogenated volatile organic compounds (HVOCs) and major ions in the samples collected at five sampling points during six campaigns were used as variablesthroughout the study. The originality...
-
Sources and Fate of PAHs and PCBs in the Marine Environment
PublicationThe assessment of a hazard resulting from the pollution of the environment by chemical compounds is in principle limited to the determination of their concentrations in its various compartments. But for solving many problems in this context, knowledge of the emission sources, transport pathways, and sites of deposition is of great benefit. By far the largest amounts of pollutants, regardless of where they were discharged, end up...
-
Isocyanate-Free Polyurethanes
PublicationIsocyanate-free polyurethanes (also called non-isocyanate polyurethanes, or NIPUs) are alternatives to the conventional (commercially used) polyurethanes synthesized using di- or polyisocyanates, polyols, and chain extenders with low molecular weight. The major routes of NIPUs’ synthesis involve polyaddition of cyclic carbonates and di- or polyamines, polycondensation of carbamates, and diols. The most important intermediates are...
-
Comparison of the Measurement Techniques Employed for Evaluation of Ambient Air Odour Quality Influenced by Operation of Industrial Sewage Treatment Plant
PublicationThe paper presents the results of investigation on ambient air quality evaluation with respect to concentration of odorants in a vicinity of a sewage treatment plant of the LOTOS Group S.A. petroleum plant. The investigation was performed during winter season using a prototype of electronic nose and the Nasal Ranger field olfactometers. The prototype was equipped with a set of six semiconductor sensors by FIGARO Co. and one PID-type...
-
Method for the determination of carboxylic acids in industrial effluents using dispersive liquid-liquid microextraction with injection port derivatization gas chromatography–mass spectrometry
PublicationThe paper presents a new method for the determination of 15 carboxylic acids in samples of postoxidative effluents from the production of petroleum bitumens using ion-pair dispersive liquid-liquid microextraction and gas chromatography coupled to mass spectrometry with injection port derivatization. Several parameters related to the extraction and derivatization efficiency were optimized. Under optimized experimental conditions,the...
-
Badania nad rozdzielaniem grupowym i analityką składu grupowego olejów bazowych i smarowych, zwłaszcza o szerokim zakresie polarności składników
PublicationRozprawa to studia i badania nad rozdzielaniem i analityką składu grupowego olejów bazowych i smarowych o szerokim zakresie polarności składników. Studium literatury wykazało brak metodyk badania udziału frakcji naftowej i roślinnej w takich olejach oraz nieadekwatność w tym celu HPLC. Pierwsza część pracy to badania nad opracowaniem wielokrotnie zastosowanej w praktyce terenowej metodyki i wyposażenia dla zastosowania fluorescencji...
-
Hydrogen production from biomass using dark fermentation
PublicationHydrogen applicability in the power, chemical and petrochemical industries is constantly growing. Efficientmethods of hydrogen generation from renewable sources, including waste products, are currently being de-veloped, even though hydrogen is mainly produced through steam reforming or thermal cracking of natural gasor petroleum fractions. In paper alternative methods of hydrogen production with a particular emphasis on darkfermentation...
-
Novel stationary phases based on asphaltenes for gas chromatography
PublicationWe present the results of investigations on the possibility of the application of the asphaltene fraction isolated from the oxidized residue from vacuum distillation of crude oil as a stationary phase for gas chromatography. The results of the investigation revealed that the asphaltene stationary phases can find use for the separation of a wide range of volatile organic compounds. The experimental values of Rohrschneider/McReynolds...
-
Method for the simultaneous determination of monoaromatic and polycyclic aromatic hydrocarbons in industrial effluents using dispersive liquid-liquid microextraction with GC-MS
PublicationWe present a new method for simultaneous determination of 22 monoaromatic and polycyclic aromatic hydrocarbons in postoxidative effluents from the production of petroleum bitumen using dispersive liquid-liquid microextraction coupled to gas chromatography and mass spectrometry. The eight extraction parameters including the type and volume of extraction and disperser solvent, pH, salting out effect, extraction and centrifugation...
-
Utilization of rapeseed pellet from fatty acid methyl esters production as an energy source
PublicationRapeseed pellet – crushed seed residue from oil extraction is a by-product of fatty acid methyl esters production process. As other types of biomass, it can either be burned directly in furnaces or processed to increase its energetic value. Biomass is renewable, abundant and has domestic usage; the sources of biomass can help the world reduce its dependence on petroleum products, fossil coal and natural gas. Energetically effective...
-
Analytics of Surfactants in the Environment: Problems and Challenges
PublicationSurfactants (surface active agents = SAAs) are a group of compoundswith specific physicochemical properties (amphiphilicity,solubility in polar and nonpolar liquids, ability to form micelles,adsorption at phase boundaries).1,2 Because of their properties,surface-active compounds are widely applied in industry and thehousehold (e.g., in detergents, personal-care products, paints,pesticides, petroleum products). As their applications...
-
Comparison of PCBs and PAHs levels in European coastal waters using mussels from the Mytilus edulis complex as biomonitors
PublicationMussels from the Mytilus edulis complex were used as biomonitors for two groups of organic pollutants: polychlorinated biphenyls (PCBs, congeners: 28, 52, 101, 118, 138, 153 and 180) and polycyclic aromatic hydrocarbons (PAHs, naphthalene, acenaphthylene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, benz(a)anthracene, chrysene, benzo(b)fluoranthene, benzo(k)fluoranthene, benzo(a)pyrene, indeno(1,2,3-cd)pyrene,...
-
Recycling of Waste Rubber by Thermo-Mechanical Treatment in a Twin-Screw Extruder
PublicationRecycling of waste tires is a significant issue considering both environmental and economic aspects. One of the leading recycling routes is the shredding of tires resulting in the generation of ground tire rubber. This material can be easily introduced into various polymer matrices as a filler, reducing the use of conventionally applied petroleum-based materials. In such cases, it is essential to ensure sufficient interfacial compatibility,...
-
Metal dusting phenomena of 501 AISI furnace tubes in refinery fractional distillation unit
PublicationThe purpose of this investigation was to conduct the failure analysis of 501 AISI furnace tubes places before distillation column in fractional distillation unit. The investigated furnace tubes were planned to work for ten years however after just two years of exploitation <30% of the material left. The observed corrosion process had the intense and complex character. The well-adhered shiny black deposits and deep, round pits were...
-
Badania eksperymentalne modelu zbiornika stalowego na stole sejsmicznym = Experimental study on steel tank model using shaking table
PublicationCylindrical steel tanks are very popular structures used for storage of products of chemical and petroleum industries. Their safety and reliability is really crucial because any failure may have serious consequences. Earthquakes are the most dangerous and also the most unpredictable dynamic loads acting on such structures. On the other hand, rockburst-induced ground motions are usually considered to be less severe due to lower...
-
IMPLEMENTATION OF INOGATE PROGRAMME IN ARMENIA, AZERBAIJAN AND GEORGIA
Publication34 IMPLEMENTATION OF INOGATE PROGRAMME IN ARMENIA, AZERBAIJAN AND GEORGIA Krystyna Gomółka Department of Social Sciences and Philosophy, Faculty of Management and Economics, Gdansk University of Technology Ul. G. Narutowicza 11/12, 80 - 233 Gdańsk, Poland Krystyna.Gomolka@zie.pg.gda.pl Abstract INOGATE Programme is one of the instruments designed for the implementation of the energy policy developed by the EU and...
-
Recycling of Waste Rubber by the Manufacturing of Foamed Polyurethane-Based Composites—Current State and Perspectives
PublicationWorn car tires are disruptive waste, and the issue of their management is crucial for the natural environment. In many countries, the primary method of end-of-life tires utilization is energy recovery. However, more effective and beneficial for the environment is material recycling. Using them for the production of polymer-rubber composites seems to be an auspicious direction of research. Incorporation of ground tire rubber into...
-
Comparative Analysis of Carbon, Ecological, and Water Footprints of Polypropylene-Based Composites Filled with Cotton, Jute and Kenaf Fibers
PublicationComposites containing natural fibers are considered environmentally friendly materials which is related to the reduced use of fossil fuels and the emission of carbon dioxide compared to petroleum-based polymers. Nevertheless, a complete evaluation of their environmental impact requires a broader view. This paper presents a carbon, ecological, and water footprints assessment of polypropylene-based composites filled with cotton,...