Search
Search results for: al2o3
-
Teoretyczno-doświadczalne modelowanie konwekcji wymuszonej nanocieczy
PublicationPrzedłożona rozprawa doktorska dotyczy badań eksperymentalnych oraz numerycznych konwekcji wymuszonej nanocieczy. Badane nanociecze wytworzone były z cieczy bazowych takich jak woda demineralizowana i mieszaniny wody z glikolem etylenowym w trzech proporcjach objętościowych 90:10, 80:20 i 60:40. Jako nanocząstki użyto Al2O3, a wytworzone nanociecze miały koncentracje masowe 0,1%, 1% i 5%. Wyznaczono eksperymentalnie dynamiczny...
-
Growth and Electric Transport of Ca-doped PrBa2Cu3O7-δSingle Crystals
PublicationCrystal growth of Ca-doped PrBa2Cu3O (Pr-123) single crystals by slow cooling of Pr3O11-CaCO3-BaCO3-CuO melts (self-flux technique) in ambient air atmosphere was studied. As the first approach the growth of Ca-free crystals in Al2O3 and ZrO2 crucibles was investigated. The best quality crystals with the average size of 5 x 5 x 0.2mm3 were obtained from Al2O3 crucibles for Ba/Cu = 0.41 and 15 wt.% (2.41 mol.%) of stoichiometric...
-
Growth and characterization of PrBa2Cu3O7-δ single crystals
PublicationWe report on the growth of PrBa2Cu3O7-δ single crystals in the Al2O3 and ZrO2 crucibles by flux method. The high influence of the reaction between crucible and liquid on the initial melt composition has been established. We found that the precipitation of the chemically stable compound BaZrO3 and BaAl2O4 occurs by direct chemical reaction between BaCuO2 and ZrO2 or Al2O3 crucibles materials. Free separated crystals with maximum...
-
Experiments on compression ignition engine powered by nano-fuels
PublicationThe use of nanoparticles in fuels provides new opportunities for modification of fuel properties, which may affect the operational parameters of engines, in particular the efficiency and fuel consumption. The paper presents comparison of compression ignition engine performance fuelled with neat diesel and nano-diesel. Alumina (Al2O3) was used as nanoparticles. Surface-active substances, including Span 80 surfactant, as well as...
-
Assessment of evaporator tubes corrosion in low-emission steam boilers
PublicationW artykule przedstawiono wyniki badań rur ekranowych(16Mo3) kotła niskoemisyjnego po jednym roku i dwóch latach eksploatacji. Powierzchnie rur pokryte zostały warstwami natryskiwanymi cieplne - pojedynczą ze stopu 70%Ni 30%Cr i podwójną Ni-30Cr /Al2O3. Rury bez powłok natryskiwanych wykazywały pocienienie ze względu na działanie korozji siarkowej oraz korozyjnego oddziaływania warstwy stopionych soli. Pojedyncza warstwa 70%Ni 30%Cr...
-
Synthesis of reduced graphene oxide nanosheets using nanofibers from methane and biogas thermal decomposition with various catalysts
PublicationReduced graphene oxide and graphene oxide (rGO, GO) were synthesised from carbon nanofibers, which were formed in catalytic thermal decomposition of methane (CDM) and biogas with different catalysts used in the process. The aim of the work was valorization of CDM carbon nanofiber products. The samples were characterized using Raman spectra, a scanning electron microscope and a transmission electron microscope. As a result, we observe...
-
Analiza czasochłonności docierania jednotarczowego powierzchni płaskich elementów ceramicznych - studium przypadku
PublicationPrzedstawiono analizę czasochłonności docierania elementów ceramicznych. Badano czasochłonność obróbki na dwóch docierarkach jednotarczowych o znacząco różniących się średnicach tarcz docierających. Porównano czasy jednostkowe docierania elementów płaskich z ceramiki technicznej Al2O3
-
Analiza czasochłonności docierania technologicznego powierzchni płaskich w operacjach montażowych.
PublicationPrzedstawiono wyniki analiz docierania i mikroszlifowania elementów płaskich na docierarce jednotarczowej mikroziarnami węglika krzemu. Obrabiano elementy ze stali 100Cr oraz z tlenkowej ceramiki technicznej Al2O3. Analizowano czas obróbki i koszty operacji.
-
Surface roughness of ceramic parts after lapping by abrasive-metallic tools
PublicationPrzedstawiono konstrukcję narzędzi ścierno-metalowych do obróbki na docierarce jednotarczowej. Wykonano badania docierania elementów z ceramiki tlenowej. Analizowano podstawowe parametry chropowatości powierzchni elementów z Al2O3 po obróbce narzędziami na bazie węglika boru.
-
Wrzenie nanocieczy na poziomych gładkich i chropowatych rurkach
PublicationPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła podczas wrzenia nanocieczy Al2O3 na rurce ze stali nierdzewnej przy ciśnieniu atmosferycznym, pod- i nadciśnieniu. Koncentracja nanocząstek o średnim wymiarze 47 nm wynosiła 0.01%, 0.1% oraz 1%.
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublicationThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublicationThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Zirconia ceramics with additions of Alumina for advanced tribological and biomedical applications
PublicationThe results of an investigation on slip cast and sintered Y2O3 (3 wt%)- stabilized ZrO2 with additions of 5, 10, 15 wt% Al2O3 are reported. The surface roughness, porosity and density of the samples were measured. The hardness HRc and Hv, fracture toughness K1C, and friction coefficients were also measured using standard methods. The structural properties of the samples were observed by Scanning Electron Microscopy (SEM). The surface...
-
Cu supported on various oxides as a candidate catalyst for dry methane reforming in DIR-SOFCs systems
PublicationA series of Cu-support systems were tested as potential candidates for DIR-SOFC (Direct Internal Reforming SOFC) catalysts towards a dry reforming of methane (DRM). The various supports (-Al2O3, CeO2, ZrO2, SrTiO3) with comparable specific surface area (SSA), and additionally -Al2O3 with SSA an order of magnitude larger than that of the other supports has been applied. The obtained Cu-support systems were characterized in terms...
-
Approaches to experiment based friction modeling: polynomial approximation versus ann approximation
PublicationBadano warunki (poziom wymuszeń), przy których następowało wzbudzenie drgań mechanicznych przy tarciu ślizgowym konforemnego skojarzenia próbek wykonanych z Al2O3 (płaskie czoło tulei obracającej się względem swojej osi - powierzchnia płaska). Uzyskane dane eksperymentalne wykorzystano następnie do zbudowania modeli - stosując aproksymację wielomianami albo sztuczną siecią neuronową (ANN).
-
Technologia wytworzenia i właściwości czujników wilgotności na bazie nanoporowatego tlenku glinu
PublicationW pracy przedstawiono opis technologii przygotowania czujników wilgotności na bazie nanoporowatego Al2O3. Celem badań było określenie związku pomiędzy parametrami procesu technologicznego a parametrami warstwy porowatej i właściwościami elektrycznymi czujnika. Strukturę powierzchni czujnika określono z wykorzystaniem elektronowej mikroskopii skaningowej. Spektroskopia impedancyjna została wykorzystana do określenia parametrów elektrycznych.
-
A Pilot Study on Machining Difficult-to-Cut Materials with the Use of Tools Fabricated by SLS Technology
PublicationThe growing use of contemporary materials in various industrial sectors, such as aerospace, automotive, as well as the oil and gas industry, requires appropriate machining methods and tools. Currently, apart from the necessity to obtain high-dimensional and shape accuracy, the efficiency and economic aspects of the selected manufacturing process are equally important, especially when difficult-to-cut materials, such as hard and...
-
Ionic conductivity behavior by activated hopping conductivity (AHC) of barium aluminoborosilicate glass–ceramic system designed for SOFC sealing
PublicationNon-conducting BaO-B2O3-Al2O3-SiO2 parent glasses designed for solid oxide fuel cell (SOFC) sealing applications were prepared using the melt-quenching technique. The glass formation region was determined according to phase equilibrium relations and was found to be in the composition range 70BaO-(x)Al2O3-(10−x)B2O3-20SiO2 where 3.0 < x < 6.0 wt%. The conductivity values obtained conductivity ranged from 10−5 to 10−10 S/cm at temperatures...
-
Measurements of droplet contact angle of nanofluids
PublicationPrzedstawiono wyniki pomiarów kąta zwilżania trzech nanocieczy: woda-Al2O3, woda-TiO2 oraz woda-Cu. Koncentracja nanocząstek wynosiła: 0.01%, 0.1% oraz 1%. Pomiary przeprowadzono dla podłoża szklanego, aluminiowego i ze stali nierdzewnej. Kąt zwilżania mierzono za pomocą goniometru, a także na podstawie zdjęć wykonanych za pomocą kamery cyfrowej.
-
ANODOWE WARSTWY KATALITYCZNE DLA TLENKOWYCH OGNIW PALIWOWYCH ZASILANYCH BIOGAZEM
PublicationW pracy wytworzono materiały (LiLaNi-Al2O3) oraz (Sm0.2Ce0.8O1.9), jako potencjalne katalizatory reakcji reformingu biogazu w tlenkowych ogniwach paliwowych. Syntezę przeprowadzono metodą Pechini’ego. Zbadano skład chemiczny oraz strukturę uzyskanych związków. Ponadto ogniwo sprawdzono podczas pracy z biogazem pod kątem odporności na osadzenie węgla, a także wpływu na długość pracy ogniwa.
-
THE POSSIBILITY OF USE OF LASER-MODIFIED Ti6Al4V ALLOY IN FRICTION PAIRS IN ENDOPROSTHESES
PublicationThe purpose of this paper is to show results of laser treatment at cryogenic conditions of the Ti6Al4V alloy used for orthopedic applications. That modification process ought to bring beneficial changes of microstructure and residual stresses in the surface layer. The paper presents the abrasive wear of the base and laser remelted material in association with ceramics Al2O3. Despite the surface cracking after laser treatment the...
-
Ocena trwałości rur ekranowych z powłokami ochronnymi eksploatowanych w kotłach niskoemisyjnych
PublicationBadania diagnostyczne powłok ochronnych - natryskiwanej cieplnie Al2O3/Ni-30Cr oraz hybrydowej nanoszonej techniką malarską - pracujących na rurach ekranowych w kotłach pyłowych niskoemisyjnych dowodzą m. in., że powłoki ochronne nie zabezpieczają powierzchni ogrzewanej rur ekranowych przed korozją płomieniową; dodatkową przyczyną niskiej trwałości powłok jest duże stężenie siarki i chloru w węglu oraz współspalanie biomasy.
-
Obróbka wykańczająca powłok MMC w aspekcie umocnienia i zmniejszenia chropowatości powierzchni
PublicationPowłoki natryskiwane cieplnie nakładane są z uwzględnieniem naddatku na obróbkę wykańczającą. Obróbka wykańczająca powinna zapewnić nie tylko odpowiednią grubość powłok związaną z wymiarem nominalnym przedmiotu ale również uzyskanie wymaganej chropowatości i falistości powierzchni. Najczęściej w tym celu stosuje się obróbkę wiórową, rzadziej szlifowanie. Ze względu na dużą chropowatość powłok kompozytowych o osnowie metalowej...
-
Utilization of shale cuttings in production of lightweight aggregates
PublicationThe development of technologies for unconventional hydrocarbon exploration requires designing procedures to manage drilling waste that are consistent with the waste management hierarchy. In view of this, the possibility to apply shale drill cuttings as a prospective additive (replacing bentonite) to fly ash used for the production of lightweight aggregates (LWAs) was investigated. Moreover, a facile, waste-free method of LWAs production...
-
Linear and nonlinear impedance of iron containing silicate glasses
Open Research DataThe linear and nonlinear impedance ofglasses doped with iron oxide were measured. Glass samples (50 SiO2-50-xPbO-xFe2O3 in mol%) were prepared by the conventional melt quenching technique. The substrates were powdered in a mortar and melted in Al2O3 crucibles. The melting was conducted in air at 1623K. The melts were poured out on plate heated up to...
-
Experimental investigation of forced convection of water/EGAl2O3 nanofluids inside horizontal tube
PublicationIn this paper, forced convection of water/EG-Al2O3 nanofluids inside horizontal stainless steel tube is studied experimentally. As base fluid served water/EG mixture of two ratios (60:50 and 50:50). Nanoparticle mass concentrations was 0.1% or and 1%. Transition and turbulent flow regimes were tested. Average heat transfer coefficient and pressure drop values were determined for nanofluids and compared to base fluids. Deterioration...
-
Szlifowanie jednostronne z wykorzystaniem ściernic o spoiwie galwanicznym
PublicationW referacie przedstawiono wyniki badań eksperymentalnych szlifowania jednostronnego ceramiki tlenkowej Al2O3 z zastosowaniem ściernic o spoiwie galwanicznym z ziarnami diamentowymi D107 i D64. Prototypowe ściernice charakteryzowały się różną wysokością warstwy spoiwa niklowego wpływającą na głębokość i trwałość utwierdzenia ziaren ściernych. Ściernice wykonano dla trzech warto- ści współczynnika hs wysokości warstwy spoiwa w stosunku...
-
INFLUENCE OF SURFACE CURVATURE ON SESSILE DROPLET CONTACT ANGLE OF NANOFLUIDS
PublicationThis paper deals with change in contact angle of droplets of three nanofluids, i.e. water-Al2O3, water-TiO2 and water-Cu. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight. Although dispersants were not used to stabilize the suspension, the solutions tested exhibited satisfactory stability. Ultrasonic vibration was used in order to stabilise the dispersion of the nanoparticles. Experimental measurements...
-
Measurement of temperature-dependent viscosity and thermal conductivity of alumina and titania thermal oil nanofluids
PublicationThe results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil was selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from 20°C to...
-
Nonlinear impedance in oxide glasses containing single and mixed alkali ions
PublicationThe aim of the present was to find more clues on the nonlinearities in impedance of oxide glasses. The first family of researched glasses has a composition of FeO-P2O5-Na2O. Oxide glasses containing iron and alkali are well known for a very low alkali ion mobility and may be considered purely polaron conducting. These glasses show no detectable nonlinearities in the impedance spectra. The second was a family of ionic conducting...
-
Vertical vibration reduction and audible sound analysis in surface grinding with electroplated tools
PublicationOne of the first approaches to the development of a grinding process monitoring system based on audible sound sensors is presented in the paper. Electroplated diamond tools (abrasive D64 and D107) were used in a modified single-disc lapping machine configuration for flat grinding of ceramics (Al2O3). The main aim of the machine modification was to reduce the vertical vibration in order to decrease the tool wear and to increase...
-
MEASUREMENT OF TEMPERATURE-DEPENDENT VISCOSITY AND THERMAL CONDUCTIVITY OF ALUMINA AND TITANIA THERMAL OIL NANOFLUIDS
PublicationIn this study results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil is selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from...
-
Stability Investigation of the PCM Nanocomposites
PublicationEnsuring the stability is a key issue to be solved for the technical application of nanocomposites. In this work, fatty acid P1801 served as base phase change material (PCM)P1801, and its main ingredients are palmitic acid (58%) and stearic acid (38%). Titania (TiO2) and alumina (Al2O3) with mass concentrations of 1% and 5% were selected as nanoparticles, while polyvinylpyrrolidone (PVP) or oleic acid (OA) with mass concentrations...
-
Effect of Nb and Al on in vitro dissolution behavior and structure of Na2O-MgO CaO-P2O5 glasses
PublicationIn vitro dissolution, structure, and thermal properties of the glass series Na2O-MgOsingle bondCaOsingle bondNb2O5 -Al2O3-P2O5 were studied. The dissolution behavior in phosphate-buffered saline (PBS) confirmed the potential bioactive properties of tested glasses. The dissolution process was found to depend on the Al, Nb, and Mg contents. Al, respectively, suppresses the Nb and accelerates the Mg release process from the glasses....
-
High temperature corrosion of evaporator tubes with thermal sprayed coatings
PublicationDegradation examinations of outer surface of low-emission steam boiler evaporator tubes are presented in the paper. Metallographic evaluation of scale morphology, its micro sites chemical composition analysis and distribution of elements on cross sections have been performed. Water-wall tubes were exposed in steam boiler for up to two years period. Common tubes made of 16Mo3 steel suffered sulphide and molten salts corrosions....
-
Odporność wybranych powłok ochronnych na korozję płomieniową w kotłach pyłowych niskoemisyjnych
PublicationW artykule omówiono zagadnienie odporności powłok na rurach ekranowych kotłów niskoemisyjnych na korozję płomieniową. Przedstawiono wyniki badań diagnostycznych powłok ochronnych na rurach ekranowych kotłów pyłowych, niskoemisyjnych, pracujących przy współspalaniu biomasy. Badano powłoki natryskiwane cieplnie Al2O3/Ni- 30Cr oraz hybrydowe nanoszone techniką malarską. Stan powłok oceniono po jednym i dwóch latach eksploatacji w...
-
Experimental Investigation of Free Convection Heat Transfer from Horizontal Cylinder to Nanofluids
PublicationThe results of free convection heat transfer investigation from a horizontal, uniformly heated tube immersed in a nanofluid are presented. Experiments were performed with five base fluids, i.e., ethylene glycol (EG), distilled water (W) and the mixtures of EG and water with the ratios of 60/40, 50/50, 40/60 by volume, so the Rayleigh (Ra) number range was 3 104 Ra 1.3 106 and the Prandtl (Pr) number varied from 4.4 to 176....
-
Burnout Investigation of Small Diameter Tubes Immersed in Nanofluids
PublicationThis paper deals with research into pool boiling critical heat flux (CHF) of water–Al2O3, water–TiO2 and water–Cu nanofluids on horizontal stainless steel tubes. The experiments were conducted under atmospheric pressure. Nanoparticles were tested at concentrations of 0.001%, 0.01%, 0.1% and 1% by weight. Ultrasonic vibration was used in order to stabilize the dispersion of the nanoparticles. Although dispersants were not used to...
-
Method of Monitoring of the Grinding Process with Lapping Kinematics Using Audible Sound Analysis
PublicationUtilising microphones as audible sound sensors for monitoring a single-side grinding process with lapping kinematics is presented in the paper. The audible sound generated during grinding depended on the cutting properties of electroplated tools with D107 diamond grains and different thicknesses of the nickel bond. The tool wear affected the obtained technological effects such as material removal rate and the surface roughness...
-
Jacek Namieśnik prof. dr hab. inż.
PeopleScientific discipline: chemistryRector in 2016-2019 He was born on 10 December, 1949 in Mogilno. He graduated in 1972 at the Faculty of Chemistry at Gdańsk University of Technology, obtaining a master's degree in chemical engineering. In 1972 he started working at Gdańsk University of Technology, where in 1978 he defended his doctoral thesis and in 1985 he completed his habilitation. He was appointed an associate professor in 1991...
-
Superconductivity in PrBa 2Cu 3O 7− δ single crystals after high-temperature thermal treatment
PublicationThe influence of post-growth treatment, consisting of high-temperature reduction, quench and oxidation, on the structural, electrical and magnetic properties of PrBa2Cu3O7−δ single crystals, obtained in Al2O3 and ZrO2 crucibles by the self-flux method, was examined. We report on the observation of inhomogeneous superconductivity in several Al-doped crystals from the ac magnetic susceptibility and resistivity measurements. Superconducting...
-
Nanolayers in Fiber-Optic Biosensing
PublicationIn this chapter, fiber-optic sensors based on nanolayers or thin films and their ability to perform biophotonic measurements is presented. In the last decade, fiber-optic sensors have gained popularity as biosensing devices. This has been made possible because of the design and the integration of new materials in fiber-optic technology. Nanolayers and thin films made from various materials such as nanodiamond (NCD), boron-doped...
-
Effect of Temperature and Nanoparticle Concentration on Free Convective Heat Transfer of Nanofluids
PublicationA theoretical analysis of the influence of temperature and nanoparticle concentration on free convection heat transfer from a horizontal tube immersed in an unbounded nanofluid was presented. The Nusselt (Nu) number and heat transfer coefficient were parameters of the intensity of the convective heat transfer. For free convection, the Nu number was a function of the Rayleigh (Ra) number and Prandtl (Pr) number. The Rayleigh (Ra)...
-
Carburization Behavior of High-Grade Pellets After Direct Reduction in Pure Hydrogen
PublicationCarburization is a critical aspect in the iron and steel industry as it significantly affects the mechanical and chemical properties of the final product. This study provides a comprehensive analysis of the carburization potential of high-grade quality iron ore pellets after direct reduction in pure hydrogen. The results show that the porosity of the pellets has a significant impact on the efficiency and success of the direct reduction...
-
Thermal analysis of Magnetohydrodynamics (MHD) Casson fluid with suspended Iron (II, III) oxide-aluminum oxide-titanium dioxide ternary-hybrid nanostructures
PublicationThis study is carried out to enhance and analyze the thermal performance of non-Newtonian Casson fluid by immersing Ternary hybrid nanoparticles Fe3O4-Al2O3-TiO2 uniformly. To model the behaviour of such complex phenomena mathematically, a system of complex transport differential equations is developed by utilizing a non-Fourier heat transfer model for energy transport. The non-dimensional system of transport equations involving...
-
Linear impedance of 10Na2O–60P2O5–30CaO glass measured with impedance spectroscopy method at low temperature region
Open Research DataThe linear electrical properties of 10Na2O–60P2O5–30CaO glass was measured by impedance spectroscopy method.
-
EFFECT OF NANOFLUID CONCENTRATION ON TWO-PHASE THERMOSYPHON HEAT EXCHANGER PERFORMANCE
PublicationAn approach – relaying on application of nanofluid as a working fluid, to improve performance of the two-phase thermosyphon heat exchanger (TPTHEx) has been proposed. The prototype heat exchanger consists of two horizontal cylindrical vessels connected by two risers and a downcomer. Tube bundles placed in the lower and upper cylinders work as an evaporator and a condenser, respectively. Distilled water and nanofluid water-Al2O3...
-
Combined Long-Period Fiber Grating and Microcavity In-Line Mach–Zehnder Interferometer for Refractive Index Measurements with Limited Cross-Sensitivity
PublicationThis work discusses sensing properties of a long-period grating (LPG) and microcavity in-line Mach–Zehnder interferometer (µIMZI) when both are induced in the same single-mode optical fiber. LPGs were either etched or nanocoated with aluminum oxide (Al2O3) to increase its refractive index (RI) sensitivity up to ≈2000 and 9000 nm/RIU, respectively. The µIMZI was machined using a femtosecond laser as a cylindrical cavity (d = 60...
-
Uwodornienie oleju sojowego i rzepakowego na katalizatorach miedziowych promotorowanych niklem i tlenkiem glinu. Hydrogenation of soybean and rapeseed oil with copper catalysts activated with nickel and aluminium oxide
PublicationBadano nowy typ katalizatorów miedziowych promotorowanych niklem, o stosunku Cu do Ni w granicach od 1:0,0036 do 1:0,018 w?w, osadzonych na Al2O3, przeznaczonych do selektywnego uwodornienia kwasu linolenowego w olejach roślinnych. Uwodornienie prowadzono w laboratoryjnym reaktorze typu "dead end" na oleju sojowym i rzepakowym, a kontakty mieszane - w stęż. 0,5% i 1% Cu. Na podstawie badań stwierdzono, że promotorowanie znacząco...
-
The influence of chitosan hydrogel coating on different redox probes kinetics
Open Research DataThis dataset contains cyclic voltammetry studies of three redox probes: 1 mM K3[Fe(CN)6], [K4Fe(CN)6], C12H14FeO2, and [Ru(NH3)6]Cl2 dissolved in 0.1 M KCl or PBS as the primary electrolyte. The studies are made for glassy carbon electrode (GC) and glassy carbon electrode covered with thin chitosan hydrogel membrane (C2A2). Cyclic voltammograms were...