Search
Search results for: COLD ACTIVE
-
APPLICATION POSSIBILITIES OF THE S960 STEEL IN UNDERWATER WELDED STRUCTURES
PublicationIn this paper, the application possibilities of the ultra-high strength (UHSS). Domex 960 steel in the underwater welded structures are analyzed. In the research, the investigated material has been tested in bead-on-plate wet welding conditions with the usage of different heat input values, namely 0.63 kJ/mm, 0.72 kJ/mm and 0.93 kJ/mm. Specimens were performed by the manual metal arc (MMA) welding method with the usage of rutile...
-
Strain-dependent behaviour of cold recycled material mixtures in cyclic compression tests
PublicationThe purpose of the study is to evaluate strain-dependent behaviour of Cold Recycled Material (CRM) mixtures using three frameworks typically applied for Hot Mix Asphalt (HMA): linear viscoelastic (LVE) limits; non-linearity directions; changes in rheological model parameters. To this aim, the complex modulus of three CRM mixtures with different bitumen-to-cement ratio (0.2, 0.6 and 1.8) was measured in cyclic compression mode,...
-
The buckling analysis of a cold-formed steel C-sectional column resting on an elastic foundation
PublicationThe paper is focused on stability analysis of different models of steel cold-formed C-section column. The analysed element may be applied as a primary load-bearing member in steel trusses or silo columns. The column can be used as a support for a wall of roof plates made of corrugated sheets. The wall sheeting that restrains the column against buckling may be considered as an elastic foundation. Due to the design solutions the...
-
The topography of Bi2VO5.5 ceramic measured with SEM and confocal microscope
Open Research DataThe topography of Bi2VO5.5 ceramics was measured by SEM and confocal microscope.
-
Linear impedance of Bi2VO5.5 ceramic prepared by traditional melt quenching technique measured with impedance spectroscopy method at low temperature region
Open Research DataThe linear electrical properties of Bi2VO5.5 ceramic prepared by traditional melt quenching technique was measured by impedance spectroscopy method.
-
Piotr Jaskuła dr hab. inż.
PeopleI am a Faculty member (Associate Professor, Highway and Transportation Research Department) at the Faculty of Civil and Environmental Engineering, Gdansk University of Technology, Poland).My main research interests include: pavement structures, interlayer bonding, pavement materials, recycling of road pavements, asphalt mixtures, bitumens, construction and maintenance of pavement structures.My lectures at the University include:...
-
Thermal visualization of Ostwald-de Waele liquid in wavy trapezoidal cavity: Effect of undulation and amplitude
PublicationThe present study is concerned with the numerical simulations of Ostwald-de Waele fluid flow in a wavy trapezoidal cavity in the presence of a heated cylinder situated at the center of the cavity. The work consists in characterizing the mixed convection as a function of the intensity of heat flow. The flow behaviour and temperature distribution in a cavity are the main focus of this study. The lower wall of the cavity is fixed...
-
Potential of novel atomic emission techniques as a tool for investigation of the possibilities of using industrial waste as additives in construction materials
PublicationNowadays, due to the global ecological crisis and ways to prevent a climate disaster, more and more attention is paid to green techno-logies and green Chemistry, which are part of the so-called “The Green Deal.” The main assumption is the optimization of the processes of producing necessary goods and the implementation of methods of managing postproduction waste in the least environmentally harmful manner. In the presented research,...
-
Polish experience with cold in-place recycling
PublicationDeep cold in-place recycling using cement and asphalt emulsion has been used for reconstruction of existing roads since the beginning of the 1990s. This paper describes the first Polish requirements for mineral-cement-emulsion mixtures. As requirements stated for the strength of the mineral-cement-emulsion mixtures were quite high, most of the mixtures were designed using high amount of cement and aggregate added for the improvement...
-
On local buckling of cold-formed channel members
PublicationThe paper deals with local buckling of the compressed flanges of cold-formed thin-walled channel beams subjected to pure bending or axially compressed columns. Arbitrarily shaped flanges of open cross-sections and the web-flange interactions are taken into account. Buckling deformation of a beam flange is described by displacement related to torsion of the flange about the line of its connection with the web. Total potential energy...
-
Cyclic behavior of FeCoCrNiMn high entropy alloy coatings produced through cold spray
PublicationeCoCrNiMn high entropy alloy powders were employed to produce coatings on carbon steel through high pressure cold spray (at 1100 °C and 7 MPa in temperature and pressure respectively). X-ray diffraction of the sprayed material revealed a dense coating with the retention of the original crystallographic structure. Once splatted, particles revealed high flattening ratio with consequent excellent adhesion of the coating to the substrate....
-
Spin-Orbit Coupling Matrix Elements in the KRb Molecule
Open Research DataThe allowed 190 spin-orbit coupling (SOC) matrix elements have been calculated for the singlet (s) and triplet (t) Sigma+ (S+), Pi (P), and Delta (D) electronic states of the KRb molecule. These SOCs are needed for investigations of areas connected with classical spectroscopy, deperturbation analysis of the observed spectra, atom-molecule and molecule-molecule...
-
Biomass Production and Removal of Nitrogen and Phosphorus from Processed Municipal Wastewater by Salix schwerinii: A Field Trial
PublicationIn many Baltic regions, short-rotation willow (Salix spp.) is used as a vegetation filter for wastewater treatment and recycling of valuable nutrients to upsurge bioeconomy development. In this context, a four-year field trial (2016–2019) was carried out near a wastewater treatment plant in eastern Finland (Outokumpu) to investigate the effect of the processed wastewater (WW) on biomass production as well as the nutrients uptake...
-
Mercury concentrations in marine biota with special focus on grey and ringed seals
PublicationMarine organisms are exposed and sensitive to effects of environmental contamination by heavy metals including different forms of mercury. Baltic seals as the top predators of the marine ecosystem are even more endangered due to (considerable) longevity as well as a long biological half-time of toxin elimination. The concentrations of mercury in seals from the Baltic is poorly known, thus the aim of this work is to determine and...
-
Determination of 3-MCPD and 2-MCPD esters in edible oils, fish oils and lipid fractions of margarines available on Polish market
Publication3-monochloropropane-1,2-diol (3-MCPD) and 2-monochloropropane-1,3-diol (2-MCPD) are intensively investigated food contaminants, which recently emerged as a serious problem within the discovery of high levels of their fatty acid esters in lipid samples. In order to monitor the concentrations of mentioned toxicants in edible oils and fats, several analytical methods have been developed so far. This paper presents the screening research...
-
Analytical chemistry in technical approaches: immobilization of biosorbent waste containing heavy metals in cemented materials
PublicationAn ecologically safe and economically justified method of stabilization of the used biosorbents was developed. Sorbent contaminated with heavy metals has been successfully solidified/stabilized using a hydraulic binder. The test results indicated that up to 1% of the biosorbent residue used could be added without compromising the compressive strength of the mortar. The compressive strength of the modified mortars did not change...
-
Advantages of the Application of the Temper Bead Welding Technique During Wet Welding
PublicationThermo-mechanically rolled S460ML steel was chosen for welding in underwater wet welding conditions by covered electrodes. The main aim of this study was to check the weldability for fillet welds in a water environment by controlled thermal severity (CTS) tests and to check the influence of temper bead welding (TBW) on the weldability of the investigated steel. Non-destructive and destructive tests showed that S460ML steel has...
-
Bacterial presence in polar regions associated with environment modification by chemical compounds including contaminants
PublicationMicrobes are omnipresent and diverse members of all biological communities. In marine and freshwater ecosystems, microorganisms form the base of the food chain supporting higher trophic levels. Even though, microbes generally are thought to live in warm regions of Earth, many of them develop in cold climates. Polar regions remain relatively protected from widespread anthropogenic disturbances, which is a consequence of its remoteness...
-
Freeze-Up Ice Jam Formation in the River Bend, a Case Study on the Inner Mongolia Reach of Yellow River
PublicationConcern has been expressed regarding the impacts of climate change on river ice and ice jam formation in cold regions. Ice jams are easily initiated in bends and narrow channels and cause disasters. In this study, observations and remote sensing monitoring are used to study the freeze-up ice jam formation of bends. Sediment transport and freezing process of the river interact, influencing bed changes profile and sedimentary budget....
-
Green TPUs from Prepolymer Mixtures Designed by Controlling the Chemical Structure of Flexible Segments
PublicationThis study concerns green thermoplastic polyurethanes (TPU) obtained by controlling the chemical structure of flexible segments. Two types of bio-based polyether polyols—poly(trimethylene glycol)s—with average molecular weights ca. 1000 and 2700 Da were used (PO3G1000 and PO3G2700, respectively). TPUs were prepared via a two-step method. Hard segments consisted of 4,4?- diphenylmethane diisocyanates and the bio-based 1,4-butanodiol...
-
Heat transfer intensification by enlarged surface roughness in the plate heat exchanger
PublicationIn the paper an experimental analysis of passive heat transfer intensification technique employed in the case of the plate heat exchanger is presented. The passive intensification was obtained by a modification of the heat transfer surface. The roughness of surface was increased by a use of glass micro-beads. Single-phase convective heat transfer in the water-water system was studied. The experiment was accomplished in two stages....
-
The structure of Bi2VO5.5 ceramic prepared by 3 different ways measured with X-ray diffraction
Open Research DataThe structure of Bi2VO5.5 ceramics was measured by XRD.
-
The influence of Nigella sativa essential oil on proliferation, activation, and apoptosis of human T lymphocytes in vitro
PublicationIn previous work, we tested the immunomodulatory effect of Nigella sativa (NS) fatty oil. Our results demonstrated that unrefined, obtained by cold pressing black cumin seed oil inhibited lymphocytes’ proliferation and induced their apoptosis in a dose-dependent manner. In this study, we examined the immunomodulatory properties of essential oil (EO) obtained from the NS seeds by hydrodistillation and its two main constituents:...
-
Experimental investigation of joint with positive eccentricity in CFS truss
PublicationDue to technological restrictions, in the case of trusses made of CFS open cross-sections, positive eccentricities in the truss joints have become very frequent. Therefore studies concerning the load-bearing capacity of truss joints with positive eccentricity were undertaken. It was assumed that the resistance of cold-formed steel (CFS) open cross-section truss joints located on compression chords and with positive eccentricity...
-
The Idea of Using Adhesive Bonds in Shaping of Cold-formed Thin-walled Beam-columns
PublicationThe chapter concerns the idea of using adhesive bonds in the shaping of cold-formed thin-walled beam-columns. The idea of adhesive-bonded connections is not new but is unlikely to have been used in the design and shaping of thin-walled beam-columns in civil engineering up to date. Metal bar structures, including (due to economic reasons) thin-walled structures, are the most common and effective means to build engineering superstructures/loadbearing...
-
Vibrational Quenching of Optically Pumped Carbon Dimer Anions
PublicationCareful control of quantum states is a gateway to research in many areas of science such as quantum information, quantum-controlled chemistry, and astrophysical processes. Precise optical control of molecular ions remains a challenge due to the scarcity of suitable level schemes, and direct laser cooling has not yet been achieved for either positive or negative molecular ions. Using a cryogenic wire trap, we show how the internal...
-
Evaluation of mercury content in combustible tobacco products by employing cold vapor atomic absorption spectroscopy and considering the moisture content: a comprehensive study
PublicationPlants are mainly made up of water, which constitutes between 80 and 90% of their weight. Moisture factor comes across as one of the most important in tobacco products. Rapid determination of moisture content in tobacco products comes at neces- sity in any tobacco management plants (before and after production). Therefore, the concern has been raised in this study to evaluate the moisture content in four kinds of combustible tobacco...
-
Experimental investigation of heat transfer enhancement in straight and U-bend double-pipe heat exchanger with wire insert
PublicationIn this paper, the possibility of heat transfer enhancement in the U-bend exchanger was presented. Experimental research has been carried out for four individual heat exchanger constructions i.e. plain tube in tube, turbulized tube in tube, plain U-bend and U-bend with turbulator. Also, heat transfer experiments for various boundary conditions were performed to obtain reference values. In case of U-bend exchanger with and without...
-
The Impact of Long-Time Chemical Bonds in Mineral-Cement-Emulsion Mixtures on Stiffness Modulus
PublicationDeep cold in-place recycling is the most popular method of reuse of existing old and deteriorated asphalt layers of road pavements. In Poland, in most cases, the Mineral-Cement-Emulsion mixture technology is used, but there are also applications combining foamed bitumen and cement. Mineral-Cement-Emulsion mixtures contain two different binding agents – cement as well as asphalt from the asphalt emulsion. Asphalt creates asphalt...
-
A new B-D-galactosidase with a low temperature optimum isolated from the Antarctic Arthrobacter sp. 20B: gene cloning, purification and characterization.
PublicationA psychrotrophic bacterium producing a coldadaptedB-galactosidase upon growth at low temperatureswas classiWed as Arthrobacter sp. 20B. A genomic DNAlibrary of strain 20B introduced into Escherichia coliTOP10F' and screening on X-Gal (5-bromo-4-chloro-3-indolyl-B-D-galactopyranoside)-containing agar plates ledto the isolation of B-galactosidase gene. The B-galactosidasegene (bgaS) encoding a protein of 1,053 amino acids,with a...
-
Novel single-stranded DNA-binding protein from psyvhrophilic bacterium Psychrobacter arcticus
PublicationTo study the biochemical properties of SSB from Psychrobacter arcticus (ParSSB), we have cloned the ssb genes obtained by PCR and have developed Escherichia coli overexpression systems. The gene consists of an open reading frame of 642 nucleotides encoding SSB protein of 213 amino acids with a calculated molecular mass of 22.8 kDa. The amino-acid sequence of ParSSB exhibits 49% identity and 57% similarity to Escherichia coli SSB....
-
Thermal and economic investigation of straight and U-bend double tube heat exchanger with coiled wire turbulator
PublicationExperimental research has been carried out for four individual heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend and U-bend with turbulator. Tests were made for the water-water system. The study covered a wide measuring range, i.e., Re = 800–9000 – on the shell side, for a constant cold water temperature of 9 ◦C and hot water of 50 ◦C. The heat exchangers were made from copper tubes with...
-
Mathematical Modeling of Ice Thrusting on the Shore of the Vistula Lagoon (Baltic Sea) and the Proposed Artificial Island
PublicationCoastal lagoons are inland and shallow water bodies, separated from the ocean by a barrier. In cold regions, ice phenomena in shallow water coastal lagoons occur every winter season. Ice is predominantly formed on the surface due to density stratification and surface cooling. The ice dynamics in such areas are dominantly affected by winds. Water dynamics also cause ice movement, but due to the large areal scale of lagoons, the...
-
Effect of surface roughness on thermal-hydraulic characteristics of plate heat exchanger
PublicationIn the paper the experimental analysis of passive heat transfer intensification in the case of modeled plate heat exchanger is conducted. The plate heat exchanger is chosen for the analysis because this kind of heat exchangers could be prospectively applied in the ORC systems, however other areas or application are equally possible. The experimental setup was assembled at the Department of Energy and Industrial Apparatus of Gdansk...
-
Stiffness of cold-recycled mixtures under variable deformation conditions in the IT-CY test
PublicationStiffness modulus belongs to the most important properties describing the cold-recycled mixtures (CRM) in terms of their usability in road pavement structures. Previous research proved that this property is strongly dependent on the scheme and conditions of the test (temperature and time of loading) and the time that has passed since the compaction of the specimen or pavement layer. It is a result of the influence of two different...
-
Mercury content in beetroot and beetroot-based dietary supplements
PublicationTotal mercury (THg) concentrations in fifty-four beetroot-based DSs and seven lots of conventional and organic beetroots (divided into unpeeled, peeled, and skins) were determined by direct thermal decomposition-gold amalgamation cold vapour atomic absorption spectrometry. The analytical procedure was optimised and validated. The recovery (%) for Hg was 101.9 and 92.73 in BCR-463 and DOLT 4, respectively. The intermediate precision...
-
The long-term properties of mineral-cement-emulsion mixtures
PublicationThis publication presents evaluation of long-term behavior of mineral-cement-emulsion (MCE) mixtures. MCE mixtures are among the major products of cold recycling of old asphalt pavements. They are composed by binding of the old materials reclaimed from the pavement and new mineral aggregate using two different binding agents – cement and bituminous emulsion. While bituminous emulsion dissolutes and binds materials quite fast, it...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART IV) MODELLING THE HEATING PROCESS AND DETERMINING THE SERVICEABILITY OF HYDRAULIC COMPONENTS DURING THE STARTING-UP IN LOW AMBIENT TEMPERATURE
PublicationDesigners of hydraulically driven machines and devices are obliged to ensure during design process their high service life with taking into account their operational conditions. Some of the machines may be started in low ambient temperature and even in thermal shock conditions (due to delivering hot working medium to cold components). In order to put such devices into operation appropriate investigations, including experimental...
-
Nonlinear impedance as a function of A.C. voltage of Bi2VO5.5 ceramic of thickness 2.88 mm was measured at 693 K with impedance spectroscopy method
Open Research DataThe nonlinear electrical properties of Bi2VO5.5 ceramic of thickness 2.88 mm was measured by impedance spectroscopy method.
-
Nonlinear impedance as a function of temperature and frequency for Bi2VO5.5 ceramic of thickness 2.52 mm was measured at different A.C. voltage with impedance spectroscopy method
Open Research DataThe nonlinear electrical properties of Bi2VO5.5 ceramic of thickness 2.52 mm was measured by impedance spectroscopy method.
-
Nonlinear impedance as a function of A.C. voltage of Bi2VO5.5 ceramic of thickness 1.63 mm was measured with impedance spectroscopy method at high temperature region
Open Research DataThe nonlinear electrical properties of Bi2VO5.5 ceramic of thickness 1.63 mm was measured by impedance spectroscopy method.
-
Nonlinear impedance as a function of A.C. voltage of Bi2VO5.5 ceramic of thickness 4.03 mm was measured with impedance spectroscopy method at high temperature region
Open Research DataThe nonlinear electrical properties of Bi2VO5.5 ceramic of thickness 4.03 mm was measured by impedance spectroscopy method.
-
Nonlinear impedance as a function of A.C. voltage of Bi2VO5.5 ceramic of thickness 2.91 mm was measured with impedance spectroscopy method at high temperature region
Open Research DataThe nonlinear electrical properties of Bi2VO5.5 ceramic of thickness 2.91 mm was measured by impedance spectroscopy method.
-
Nonlinear impedance as a function of frequency for Bi2VO5.5 ceramic of thickness 2.88 mm was measured at high temperature range with impedance spectroscopy method
Open Research DataThe nonlinear electrical properties of Bi2VO5.5 ceramic of thickness 2.88 mm was measured by impedance spectroscopy method.
-
Nonlinear impedance as a function of A.C. voltage and temperature for Bi2VO5.5 ceramic of thickness 2.52 mm (after first heat-treatment at 913 K) was measured at different frequencies with impedance spectroscopy method
Open Research DataThe nonlinear electrical properties of Bi2VO5.5 ceramic of thickness 2.52 mm was measured by impedance spectroscopy method.
-
Analysis of the Heating Process of Hydraulic Motors during Start-Up in Thermal Shock Conditions
PublicationConditions that prevail during harsh winters and hot summers pose a serious challenge for machine designers building devices suitable for operation in extreme weather. It is essential for the designers and the users to define the principles and conditions for the safe operation of machines and devices with hydraulic drive in low ambient temperatures. Bearing in mind the above, the author tested the hydraulic motors in thermal shock...
-
Measured and predicted freeze-thaw days frequencies in climate change conditions in central Poland
PublicationThe rate of progression of geomorphological phenomena is greatly influenced by freeze-thaw processes. In the face of air temperature increasing over the past few decades, a question of the future impact of these processes arises, notably in the temperate and cold climate zones. Using the mean, maximum and minimum daily air temperature data in the period 1951–2018 obtained from three weather stations located in the vicinity of Jeziorsko...
-
Fruit seeds oils as a cosmetic emulsions component
PublicationThe fruit seeds are known to have a considerable amount of oil and their potential specialty as nutraceutical oil was suggested based on high level of unsaturated triacyglycerols (major fatty acids are linoleic, linolenic, oleic) and a high content of tocols (tocopherols and tocotrienols). In this study the possibility of application fruit seeds oils in W/O and O/W emulsion systems was investigated to find the influence of the...
-
Free trade with the former COMECON Countries as Unequal Exchange
PublicationTwo authors of this chapter were born to the East of what was once The Iron Curtain and two to the West. From both angles, the two systems – capitalism and communism – seemed to be as contrary to each other as possible. Few people are aware that in terms of industrial and trade policy, both classical capitalism and communism had a common root in the theories of German economist Friedrich List (1789-1846) (List, 1841). In fact,...
-
Activation Energy and Inclination Magnetic Dipole Influences on Carreau Nanofluid Flowing via Cylindrical Channel with an Infinite Shearing Rate
PublicationThe infinite shear viscosity model of Carreau fluid characterizes the attitude of fluid flow at a very high/very low shear rate. This model has the capacity for interpretation of fluid at both extreme levels, and an inclined magnetic dipole in fluid mechanics has its valuable applications such as magnetic drug engineering, cold treatments to destroy tumors, drug targeting, bio preservation, cryosurgery, astrophysics, reaction kinetics,...