Filters
total: 576
filtered: 498
Search results for: EQUIVALENT IMPERFECTIONS
-
Energy neutrality versus carbon footprint minimization in municipal wastewater treatment plants
PublicationThis work aimed to compare the carbon footprint (CF) of six full-scale wastewater treatment plants (WWTPs). The CF was estimated in the range of 23–100 kg CO2e per population equivalent. In the total CF, the direct emissions held the highest share (62–74%) for the plants with energy recovery from biogas. In the plants depending entirely on the power grid, the indirect emissions due to energy consumption dominated the total CF (69–72%)....
-
Unconditional privacy over channels which cannot convey quantum information
PublicationQuantum cryptography enables one to verify that the state of the quantum system has not been tampered with and thus one can obtain privacy regardless of the power of the eavesdropper. All previous protocols relied on the ability to faithfully send quantum states or equivalently to share pure entanglement. Here we show this need not be the case-one can obtain verifiable privacy even through some channels which cannot be used to...
-
Cichy sonar - stan aktualny i perspektywy
PublicationW zastosowaniach militarnych często istnieje potrzeba prowadzenia obserwacji w sposób skryty za pomocą urządzeń emitujących sygnały trudne do przechwycenia przez przeciwnika. Rozwiązania stosowane w cichych radarach stanowiły punkt wyjścia do opracowania cichego sonaru. Prace nad projektem rozpoczęto na Politechnice Gdańskiej w roku 2010 w ramach Grantu NCBiR i są one dalej kontynuowane. W celu zachowania w cichym sonarze warunków...
-
Experimental and numerical investigations of ultimate strength of degradated structures
PublicationThe presented work investigates the corrosion influence on the structural behaviour of structural elements. Nine welded large-scale stiffened plates, and 30 standard small specimens have been subjected to the accelerated marine immersed conditions. After corrosion testing, the specimens have been accurately measured in terms of surface characteristics. The coupon specimens were furtherly subjected to tensile loading to develop...
-
Synchronous generator model taking into account the non-uniform saturation of the pole shoes
PublicationFor the evaluation of modern electric power systems with regard to their behavior, weight, and reliability a novel modeling and simulation tools have been developed. The paper presents circuit model of synchronous generator taking into account both the non-sinusoidal distribution of the stator and rotor winding, and non-uniform saturation of the pole shoes. This model is suitable for simulation of both salient and no-salient pole...
-
Common-Mode Voltage and Bearing Currents in PWM Inverters: Causes, Effects and Prevention
PublicationIn modern induction motor drives an increase of transistors' switching frequency and a decrease of switching times are the sources of some serious problems. The high dv/dt and the common mode voltage generated by the inverter PWM control results in the appearances of bearing currents, shaft voltages, motor terminal overvoltages, the decrease of motor efficiency, and electromagnetic interference. The aspects of common mode (CM)...
-
Application of electrochemical impedance spectroscopy to monitoring discharging process of nickel/metal hydride battery.
PublicationThis paper presents the possibility of applying impedance analysis to cell diagnostics. In order to obtain characteristic curves of both electrodes of a NiMH battery simultaneously, a reference electrode was added into the circuit. The authors analysed the cell under three cases, i.e. when its properties are determined only by the state of the positive electrode, only by the state of the negative electrode, or when both electrodes...
-
Identification of the mechanical properties of the skin by electromechanical impedance analysis of resonant piezoelectric actuator
PublicationThis paper is devoted to the analysis and verification of developed piezoelectric sensor/actuator for measuring the mechanical properties of soft tissues, especially human skin. The key element of the measurement structure is an electromechanical system that uses both the reverse piezoelectric effect (vibration generation – stimulation of the tissues in the appropriate frequency range) and direct piezoelectric effect (system response...
-
Seismic pounding behavior of multi-story buildings in series considering the effect of infill panels
PublicationThe aim of the present paper is to study the influence of the infill panels on the seismic pounding response of adjacent structures in series. The contribution of the masonry infill has been simulated using equivalent diagonal compression struts. Steel frames have been assumed to have elastic-plastic behavior with 1% linear strain hardening. The dynamic contact analysis has been utilized where contact surface model (target and...
-
NON-LOCAL VOLUMETRIC APPROACH TO ANALYSIS DEFECT'S SHAPE INFLUENCE ON SPECIMENS DURABILITY SUBJECTED TO BENDING AND TORSION
PublicationThe influence of defect features on fatigue behaviour is a complex trivial issue. Although the important advances over the last decades, the dialectical relationship between the defect orientation and durability is not clearly understood. The paper aims at studying the influence of the orientation of elliptical defects on the durability of samples made of C45 steel. Three types of samples with elliptical defects were subjected...
-
An isogeometric finite element formulation for geometrically exact Timoshenko beams with extensible directors
PublicationAn isogeometric finite element formulation for geometrically and materially nonlinear Timoshenko beams is presented, which incorporates in-plane deformation of the cross-section described by two extensible director vectors. Since those directors belong to the space R3, a configuration can be additively updated. The developed formulation allows direct application of nonlinear three-dimensional constitutive equations without zero...
-
Implicit Space Mapping for Variable-Fidelity EM-Driven Design of Compact Circuits
PublicationSpace mapping (SM) belongs to the most successful surrogate-based optimization (SBO) methods in microwave engineering. Among available SM variations, implicit SM (ISM) is particularly attractive due to its simplicity and separation of extractable surrogate model parameters and design variables of the circuit/system at hand. Unlike other SM approaches, ISM exploits a set of preassigned parameters to align the surrogate with the...
-
Local hidden–variable models for entangled quantum states
PublicationWhile entanglement and violation of Bell inequalities were initially thought to be equivalent quantum phenomena, we now have different examples of entangled states whose correlations can be described by local hidden-variable models and, therefore, do not violate any of the Bell inequalities. We provide an up-to-date overview of the existing literature regarding local hidden-variable models for entangled quantum states, in both...
-
Application of linear buckling sensitivity analysis to economic design of cylindrical steel silos composed of corrugated sheets and columns
PublicationThe paper deals with global stability of steel cylindrical silos composed of corrugated walls and vertical columns with loads imposed by a bulk solid following Eurocode 1. The optimum silo design with respect to the steel weight was based on a sensitivity analysis method. The changes of silo column profiles at each design step were performed by means of influence lines for the buckling load factor due to the unit column bending...
-
Inhomogeneity of low-noise wearing courses evaluated by tire/road noise measurements using the close-proximity method
PublicationPerforming numerous analyses of tire/road noise measurements on low-noise pavements during the last several years, the authors observed significant inhomogeneity of the wearing course in numerous cases, while similar problems were almost non-existent when dense pavements were measured. Three main causes of low-noise pavement inhomogeneity can be defined. The first one is imperfections in the technology used for asphalt mix production...
-
Дослідження проблем зайнятості випускників навчальних закладів
PublicationУ зв'язку зі зниженням загального рівня зайнятості та з огляду на кризові явища в українській економіці актуальною залишається проблема працевлаштування молоді. Спільність проблеми зайнятості випускників вишів як в Україні, так і в Європі дала змогу провести міжнародне дослідження, щоб виявити основні причини її виникнення. Результати досліджень підтвердили гіпотезу авторів. В її основі лежить комплекс причин, що пов’язані як зі...
-
New oryginal generic technologies: A Polish R&D strategic implementation programme
PublicationPolands's pharmaceutical industry is of great significance to the whole economy. According to Forbs (2 October 2012), the cost of launching a new drug varies from USD 1 to 11 bilion. There is little Chance of a Polish pharmaceutical company developing an original drug due to financial reason.Many research teams in Poland take up research projects aimed at new biologically active compounds. But such an objective has no broader perspective,...
-
FDTD Simulations on Disjoint Domains with the Use of Discrete Green's Function Diakoptics
PublicationA discrete Green's function (DGF) approach to couple disjoint domains in the finite-difference time-domain (FDTD) grid is developed. In this method, total-field/scattered-field (TFSF) FDTD domains are associated with simulated objects whereas the interaction between them is modeled with the use of the DGF propagator. Hence, source and scatterer are simulated in separate domains and updating of vacuum cells, being of little interest,...
-
Comparison of different one-parameter damage laws and local stress-strain approaches in multiaxial fatigue life assessment of notched components
PublicationThis paper aims to compare the predictive capabilities of different one-parameter damage laws and local stress-strain approaches to assess the fatigue lifetime in notched components subjected to proportional bending-torsion loading. The tested fatigue damage parameters are defined using well-known stress-based, strain-based, SWT-based and energy-based relationships. Multiaxial cyclic plasticity at the notch-controlled process zone...
-
Impact of trajectory simplification methods on modeling carbon dioxide emissions from ships
PublicationModels of ship fuel consumption and emissions play an essential role in estimating global shipping’s greenhouse gas emissions. They are also widely used for verification of reported CO2 emissions for systems like EU MRV (Monitoring, Reporting and Verification) or IMO DCS (Data Collection System). Such models achieve high accuracy using historical spatiotemporal information about each ship from AIS data. However, this approach requires substantial...
-
Development of the New Polish Method for Capacity Analysis of Motorways and Expressways
PublicationThe paper presents development of the new Polish method for performing capacity analysis of basic segments of dual carriageway roads (motorways and expressways). The method is based on field traffic surveys conducted at 30 motorway and expressway sites (class A and S roads) in Poland. Traffic flows, composition and travel times were observed in 15-min intervals at each site using ANPR filming method. These data were used to calibrate...
-
How to evaluate methods used in chemical laboratories in terms of the total chemical risk? – a ChlorTox Scale
PublicationReliable assessment of the health and environmental risk associated with the use of chemicals is critical to ob- jectively evaluate the greenness and whiteness of an analytical method. An objective and useful way of risk assessment should take into account all the relevant properties of used substances, their actual amounts needed for application of the method, and quantify the assessment result using a standardized unit. This...
-
New σ-phases in the Nb–X–Ga and Nb–X–Al systems (X = Ru, Rh, Pd, Ir, Pt, and Au)
PublicationPreviously unreported σ-phases in the ternary niobium-based systems Nb–X–Ga for X = Ru, Rh, Pd, Ir, Pt, Au, and Nb–X–Al for X = Ir, and Pt are presented, prepared by arc-melting followed by annealing at 1000 °C for 1 week. The phases are primitive tetragonal (P42/mnm, no. 136) with lattice parameters of a = 9.8336(2)–9.9432(1) Å and c = 5.1098(1)–5.1718(1) Å. Refinements of the single crystal X-ray diffraction data for the Ru and...
-
Reduced-cost surrogate modelling of compact microwave components by two-level kriging interpolation
PublicationFull-wave electromagnetic (EM) analysis is a versatile tool for evaluating the performance of high-frequency components. Its potential drawback is its high computational cost, inhibiting the execution of EM-driven tasks requiring massive simulations. The applicability of equivalent network models is limited owing to the topological complexity of compact microstrip components because of EM cross-coupling effects. Development of...
-
Piezoresponse force microscopy and dielectric spectroscopy study of Ba0.6Sr0.4TiO3 thin films
PublicationResearch on synthesis, characterization and determination of processing – structure – property relationships of commercially important ferroelectric thin films has been performed. The sol-gel-type solution deposition technique was applied to produce good quality thin films of Ba0.6Sr0.4TiO3 (BST60/40) chemical composition on the stainless steel substrates. The thin films were characterized in terms of their microstructure, crystal...
-
Dissimilar underwater wet welding of HSLA steels
PublicationThe high-strength low-alloy S460ML and S460N steels were chosen for underwater wet welding of dissimilar T-joints using covered electrodes. For improving the quality of joints, the temper bead welding (TBW) method was used. The application of TBW in pad welding conditions has been investigated earlier but the possibility of usage of this technique in welded joints was not analyzed. The main aim of the study was to check the influence...
-
Network Graph Transformation Providing Fast Calculation of Paths for Resilient Routing
PublicationProtection of transmission against failures can be appropriately dealt with by alternative paths. However, common schemes (e.g., Bhandaris scheme) are characterized by a remarkable delay while determining the transmission paths. This in turn may have a serious impact on serving dynamic demands (characterized by relatively short duration time). As a remedy to this problem, we introduce an approach to pre-compute the sets of disjoint...
-
Uncertainty of antioxidant profiling in complex mixtures using liquid chromatography involving post-column derivatisation
PublicationThe main goal of this paper is to discuss the problems associated with antioxidant profiling in complex samples using a high-throughput HPLC system coupled with post-column derivatisation reactor. Based on the experimental data reported in the literature, we demonstrated that improper optimisation of temperature and/or pH assay conditions performed using an on-line derivatisation reactor may substantially change the antioxidant...
-
In-situ and ex-situ resistance measurements of polypyrrole film using double-band electrode
PublicationMany in-situ techniques are performed in order to determine the resistance of conducting polymer film. However, the resistance measured in solution can be the combination of polymer resistance and that of other components, such as resistance of supporting electrolyte. Therefore, in this work, the influence of the solution on the resistance of polypyrrole (PPy) film has been studied. PPy film was electrchemically synthesized onto...
-
Structure analysis and thermal degradation characteristics of bio-based poly(propylene succinate)s obtained by using different catalyst amounts
PublicationLinear bio-based polyester polyols were prepared with the use of succinic acid and 1.3-propanediol (both with natural origin). As a catalyst was used tetraisopropyl orthotitanate (TPT). In order to determine the effect of various catalyst content on the thermal degradation characteristics, three different TPT amounts, as a 1.3-propanediol equivalent, were used, namely 0.1 mass% (PPS-0.1), 0.2 mass% (PPS-0.2) and 0.25 mass% (PPS-0.25)....
-
Asynchronous Charge Carrier Injection in Perovskite Light-Emitting Transistors
PublicationUnbalanced mobility and injection of charge carriers in metal-halide perovskite light-emitting devices pose severe limitations to the efficiency and response time of the electroluminescence. Modulation of gate bias in methylammonium lead iodide light-emitting transistors has proven effective in increasing the brightness of light emission up to MHz frequencies. In this work, a new approach is developed to improve charge carrier...
-
Low-cost and reliable geometry scaling of compact microstrip couplers with respect to operating frequency, power split ratio, and dielectric substrate parameters
PublicationA technique for rapid re-design of miniaturised microstrip couplers with respect to operating conditions as well as material parameters of the dielectric substrate is proposed. The dimension scaling process is based on a set of pre-optimised reference designs, obtained for an equivalent circuit model of the coupler at hand. The reference designs are utilised to construct an inverse surrogate model which – upon suitable correction...
-
COMPARISON OF NOISE EMISSION OF HCT AND CLASSIC VEHICLE COMBINATIONS FOR TIMBER TRANSPORTATION IN SWEDEN
PublicationBy means of a special simulation tool, the noise emission of a high-capacity heavy vehicle (11 axles) was compared to that of a classic heavy vehicle (a truck-dolly-semitrailer with 8 axles). The two cases are designated “Extended vehicle” versus “Classic vehicle” in this study, having total lengths of 34 and 25 m, respectively. The Classic vehicle represents the most common articulated heavy vehicle configuration for transport...
-
A Thermographic Measurement Approach to Assess Supercapacitor Electrical Performances
PublicationThis paper describes a proposal for the qualitative assessment of condition of supercapacitors based on the conducted thermographic measurements. The presented measurement stand was accompanied by the concept of methodology of performing tests. Necessary conditions, which were needed to minimize the influence of disturbing factors on the performance of thermal imaging measurements, were also indicated. Mentioned factors resulted...
-
Zero-Pole Approach in Microwave Passive Circuit Design
PublicationIn this thesis, optimization strategies for design of microwave passive structures including filters, couplers, antenna and impedance transformer and construction of various surroogate models utilized to fasten the design proces have been discussed. Direct and hybrid optimization methodologies including space mapping and multilevel algorithms combined with various surrogate models at different levels of fidelity have been utilized...
-
Study of oxygen electrode reactions on symmetrical porous SrTi0.30Fe0.70O3-δ electrodes on Ce0.8Gd0.2O1.9 electrolyte at 800 °C–500 °C
PublicationIron doped strontium titanates (SrTi1-xFexO3-δ) are an interesting mixed ionic-electronic conductor model used to study basic oxygen reduction/oxidation reactions. In this work, we performed an impedance spectroscopy study on symmetrical porous SrTi0.30Fe0.70O3-δ (STF70) electrodes on a ceriabased electrolyte. The sample was measured in varying oxygen concentration: from 0.3% to 100% in 800 °C - 500 °C temperature range. Low polarisation...
-
Bis(ammonium) Zoledronate Dihydrate
PublicationNeutralization of 2-(1-imidazole)-1-hydroxyl-1,1`-ethylidenediphosphonic acid (zoledronic acid) by an excess of ammonia yielded bis(ammonium) zoledronate dihydrate, {C5H8N2O7P2 2−, 2(H4N+), 2(H2O)}. The product is readily soluble in water and forms monocrystals for which the X-ray structural analysis was carried out. The zoledronic anion is of double negative charge due to deprotonation of three P–OH groups and protonation of the...
-
Tmscl as a rate accelerating additive in acylations of amines with 5-(α-amino- α'-hydroxy)methylene meldrum's acids
PublicationAspects are presented of the acylation of amines, alcohols and thiols with 5-(α-amino- α'-hydroxy)methylene Meldrum's acids. We placed special emphasis on the acylation reaction of secondary amines with 5-(α-amino- α'-hydroxy)methylene Meldrum's acids, which, due to their basicity, caused problems concerning salt formation with a Meldrum acid derivative. We found that secondary amines, which react at the slowest rate and with a...
-
TMSCL as a rate accelerating additive in acylations of amines with 5-(α- amino-α'-hydroxy)methylene meldrum's acids
PublicationAspects are presented of the acylation of amines, alcohols and thiols with 5-(α-amino- α'-hydroxy)methylene Meldrum's acids. We placed special emphasis on the acylation reaction of secondary amines with 5-(α-amino- α'-hydroxy)methylene Meldrum's acids, which, due to their basicity, caused problems concerning salt formation with a Meldrum acid derivative. We found that secondary amines, which react at the slowest rate and with a...
-
Atom-economic thiophosphoroselenenylations of C–H acid esters and amides
PublicationThree improved thiophosphoroselenenylation procedures of CHacids, including derivatives of malonic and acetyl-, phosphono-, 4-nitrophenyl- and 3-pyridylacetic acids, have been described and compared to previously reported thiophosphoroselenylation of diethyl malonate using bis(disopropoxyphosphinothioyl)diselenide alone or with the aid of methyl iodide. The use of iodine makes it possible to utilize both equivalents of the selenenylating...
-
Mieszanie w klasie niejednorodnych łańcuchów Markowa i kwadratowych operatorów stochastycznych
PublicationRozprawa doktorska poświęcona jest zagadnieniu asymptotycznych własności w klasie nieskończenie wymiarowych niejednorodnych łańcuchów Markowa z czasem dyskretnym oraz w klasie kwadratowych operatorów stochastycznych. W pierwszej kolejności definiowane są różne rodzaje asymptotycznego zachowania (mieszania) niejednorodnych łańcuchów Markowa odpowiadające zbieżności w normowej i mocnej topologii operatorowej oraz omówione są relacje...
-
Quality Assurance and Quality Control in the Analytical Chemical Laboratory. A practical approach : Second edition
PublicationThe second edition defines the tools used in QA/QC, especially the application of statistical tools during analytical data treatment. Clearly written and logically organized, it takes a generic approach applicable to any field of analysis. The authors begin with the theory behind quality control systems, then detail validation parameter measurements, the use of statistical tests, counting the margin of error, uncertainty estimation,...
-
Theory versus experiment for vacuum Rabi oscillations in lossy cavities
PublicationThe 1996 experiment by Brune et al. [Phys. Rev. Lett. 76, 1800 (1996)] on vacuum Rabi oscillation is analyzed by means of alternative models of atom-reservoir interaction. Agreement with experimental Rabi oscillation data can be obtained if one defines jump operators in the dressed-state basis and takes into account thermal fluctuations between dressed states belonging to the same manifold. Such low-frequency transitions could...
-
New ceramic materials derived from pyrolyzed poly(1,2-dimethylsilazane) and starch as a potential anode for Li-ion batteries
PublicationNewmaterialswere obtained by pyrolysis of starch (S) and poly(1,2-dimethylsilazane) (PSN) (weight ratio: PSN/S 30/70) at temperature a) 500 °C, b) 700 °C and c) 900 °C. Ceramic materials were characterized by infrared spectroscopy, TGA, Raman spectroscopy and SEM. New Si\O and shifted Si\C stretching vibration modes emerged confirming direct interaction between silicon originating fromsilazane and oxygen coming fromstarch. The...
-
Applications of the discrete green's function in the finite-difference time-domain method
PublicationIn this paper, applications of the discrete Green's function (DGF) in the three-dimensional (3-D) finite-difference time-domain (FDTD) method are presented. The FDTD method on disjoint domains was developed employing DGF to couple the subdomains as well as to compute the electromagnetic field outside these subdomains. Hence, source and scatterer are simulated in separate subdomains and updating of vacuum cells, being of little...
-
Novel Complementary Resonator for Dielectric Characterization of Substrates Based on Permittivity and Thickness
PublicationThis paper presents a novel complementary resonator featuring high sensitivity, low fabrication cost, and improved performance. The proposed structure consists of a complementary concentric square and circular ring resonator (CCSCRR) with multiple splits to enhance the inductance of the resonator. The proposed CCSCRR is coupled to a microstrip transmission line with an impedance of fifty ohms to create a high-sensitivity sensor....
-
Highly-Miniaturized Self-Quadruplexing Antenna Based on Substrate-Integrated Rectangular Cavity
PublicationThis paper introduces a novel self-quadruplexing antenna (SQA) architecture using a substrate-integrated rectangular cavity (SIRC) for compact size, wide-frequency re-designability, and high isolation responses. The proposed SQA is developed by engraving two U-shaped slots (USSs) on the top conductor of the SIRC. The USSs are excited by employing four microstrip feedlines to achieve self-quadruplexing antenna characteristics. The...
-
Ship weather routing optimization with dynamic constraints based on reliable synchronous roll prediction
PublicationShip routing process taking into account weather conditions is a constrained multi-objective optimization problem and it should consider various optimization criteria and constraints. Formulation of a stability-related, dynamic route optimization constraint is presented in this paper. One of the key objectives of a cross ocean sailing is finding a compromise between ship safety and economics of operation. This compromise should...
-
The retrofitting of ships by applying retractable bow hydrofoils: a case study
PublicationIncreasing environmental requirements and a relatively long ship life of 30 years mean more attention is needed to retrofit existing ships. One possibility is using hydrofoils to reduce the ship’s resistance and improve comfort and safety in rough sea conditions. This study investigates the influence of retractable bow hydrofoils on the seakeeping performance and operational conditions of a selected case study vessel (V-shaped...
-
Fabrication and Study of BiNbO4 Ceramics
PublicationAim of the present research was to fabricate and study crystalline structure as well as dielectric properties of BiNbO4 ceramics. In the present study BiNbO4 ceramics was fabricated by solid state reaction from the mixture of simple oxides viz. Bi2O3, and Nb2O5. Stoichiometric mixture of the powders was thermally analyzed so parameters of the thermal treatment were determined. The EDS measurements proved conservation of the chemical...