Search results for: TAUC PLOT
-
ECU calibration for gaseous dual fuel supply system in compression ignition engines
PublicationThe dual fuel (DF) combustion mode is proven solution that allows to improve or get at the same level engine performance and reduce toxic compounds in exhaust gases which is confirmed by researchers and end-users. DF combustion mode uses two fuels gaseous fuel as a primary energy source and a pilot quantity of diesel fuel as ignition source. However, in order, to fully take advantage of the potential of the dual fuel mode, DF system...
-
On-line measurement of wood surface smoothness
PublicationThe latest progress in the field of optics and microelectronics resulted in development of new generation vision systems capable of scanning surface topography with very high sampling frequencies. The blue color of illuminating light as well as novel systems for controlling ultra-thin laser line thickness allows measurement of the porous surface of wood with a triangulation method. Three alternative sensors were tested here in...
-
Simulation-Based Design of Microstrip Linear Antenna Arrays Using Fast Radiation Response Surrogates
PublicationFast yet accurate technique for simulation-based design of linear arrays of microstrip patch antennas is presented. Our technique includes: (i) optimization of the corrected array factor of the antenna array under design for a phase excitation taper resulting in reduced side lobes; (ii) simulation-driven optimization of the array element for element dimensions resulting in matching at and about operational frequency, and (iii)...
-
Decomposition of Acoustic and Entropy Modes in a Non-Isothermal Gas Affected by a Mass Force
PublicationDiagnostics and decomposition of atmospheric disturbances in a planar flow are considered in this work. The study examines a situation in which the stationary equilibrium temperature of a gas may depend on the vertical coordinate due to external forces. The relations connecting perturbations are analytically established. These perturbations specify acoustic and entropy modes in an arbitrary stratified gas affected by a constant...
-
Superconductivity and itinerant ferromagnetism of Y9Co7 probed by ac susceptibility
PublicationThe ac magnetic susceptibility of a single crystal sample of the compound Y9Co7 has been measured in applied dc fields ranging from 0–6.7 kOe by utilizing a tunnel diode resonator circuit. In agreement with previous measurements on this material, a superconducting transition has been observed to occur at TSC ≈ 2.5 K. A broad maximum has been observed in the zero field susceptibility measurements from 2.5 K < T < 8 K and its behavior...
-
A measurement system for children endurance tests
PublicationThere are a lot of ethical problems concerning the use of invasive methods for the measurement of a child's body response to physical exercise and physical training. The alternative is are non-invasive methods like ergospirometry or NIRS. The article presents a measurement system dedicated for children endurance tests, composed of a few non-invasive measurement modules, including a temperature measurement module. Temperature is...
-
Trust in Electronic Word-of-Mouth (eWOM): the concept and the most important determinants
PublicationeWOM and trust in it is now the most important factor in determining buyers' purchasing behavior. Familiarity with the determinants of trust establishes the formation of appropriate marketing activities. However, the growing number of new forms of eWOM and its increasingly complex and multidimensional nature have created a lot of confusion. The article aims to organize the concepts related to trust in eWOM, to indicate the most...
-
Gendered entrepreneurship and its impact on firm innovativeness - a literature review.
PublicationEntrepreneurs gain a lot of attention in recent decades. Even if a precise definition of entrepreneur and entrepreneurship remains problematic, it is clear that there is a strong link between entrepreneurship and innovativeness, as well as between entrepreneur and innovation. In the current era of globalisation, the importance of innovations is as great as never before. And so is the importance of innovativeness determinants. Investigating...
-
Bus bays inventory using a terrestrial laser scanning system
PublicationThis article presents the use of laser scanning technology for the assessment of bus bay geo-location. Ground laser scanning is an effective tool for collecting three-dimensional data. Moreover, the analysis of a point cloud dataset can be a source of a lot of information. The authors have outlined an innovative use of data collection and analysis using the TLS regarding information on the flatness of bus bays. The results were...
-
Miscanthus × giganteus root anatomical traits measurements
Open Research DataThis data set presents the optical microscope measurements/ images of Miscanthus × giganteus (M×g) roots. The experiment was performed under work package 1: "Properties characterisation of two types of biochar", task D_RT: Phyto-analyses (stress response of plants on biochar amendments) in cooperation with Aarhus University. A short term pot experiment...
-
Automated detection of pronunciation errors in non-native English speech employing deep learning
PublicationDespite significant advances in recent years, the existing Computer-Assisted Pronunciation Training (CAPT) methods detect pronunciation errors with a relatively low accuracy (precision of 60% at 40%-80% recall). This Ph.D. work proposes novel deep learning methods for detecting pronunciation errors in non-native (L2) English speech, outperforming the state-of-the-art method in AUC metric (Area under the Curve) by 41%, i.e., from...
-
Tworzenie miejskości po 1990r., Geneza niemieckiej urbanistyki współczesnych założeń mieszkaniowych
PublicationArtykuł jest przyczyną do przypomnienia genezy współczesnej formy niemieckich miejskich struktur mieszkaniowych w kontekście zmian rozumienia ich wymiaru miejskości. Niemiecka myśl urbanistyczna łączy w sobie dwie wyraziste tradycje dwudziestego wieku - Gründerzeit i KlassischeModerne. Pozostaje jednak silnie otwarta na innowację generowaną nie tylko dzięki postępowi technicznemu, ale przede wszystkim poprzez planowanie interdyscyplinarne...
-
The short-term flicker severity level measured in the industrial power system supplying the rolling mill motors
Open Research DataThe dataset presents a short-term flicker severity level measured on the bus bars of the main switchgear of the industrial power network for the supply of rolling mills. The data were obtained during an experiment whose purpose was to determine a level of short-term and long-term flicker caused by voltage fluctuations. In the virtual application of...
-
A cumulative probability function of instantaneous flicker sensation values measured in the industrial power system supplying the rolling mill motors
Open Research DataThe dataset presents a cumulative probability function CPF of the instantaneous flicker sensation level measured on the bus bars of the main switchgear of the industrial power network for the supply of rolling mills. The data were obtained during an experiment whose purpose was to determine a level of short-term and long-term flicker caused by voltage...
-
Multiresidue Methods for Determination of Currently Used Pesticides in Fruits and Vegetables Using QuECHERS Technique
PublicationApplied all over the world, pesticides are some of the most common pollutants of the environment because of their stability, mobility, their consequent long-term adverse effects on living organisms in general and human health in particular. For these reasons it is essential to monitor and analyse pesticide residues in the fruits and vegetables. The analysis of food samples for the presence of pesticides causes a lot of difficulties...
-
Postulates for measures of genuine multipartite correlations
PublicationA lot of research has been done on multipartite correlations. However, it seems strange thatthere is no denition of so called genuine multipartite correlations. In this paper we propose threereasonable postulates which each measure or indicator of genuine multipartite correlations (or gen-uine multipartite entanglement) should satisfy. We also introduce degree of correlations which givespartial characterization of multipartite...
-
Public spaces connecting cities. Green and Blue Infrastructures potential.
PublicationA city fragmentation causes a lot of negative effects in urban environment such as: disconnecting the environmental, functional and compositional relations, a loss of urban compactness, chaotic development, visual chaos, a domination of technical landscape, reduction of security. This is why one of main challenges for urban planners is to connect the fragmented structures by creating friendly, attractive and safe public space....
-
Optical glyphs based localization and identification system
PublicationThe paper presents a description of functioning of a platform supporting the detection of obstructive diseases in the respiratory system education process. A 16-parameter model of the respiratory system simulated in the MATLAB/Simulink environment was set in the role of the tested patient. It has been linked to the control layer, developed in the LabVIEW environment, using the SIT library (Simulation Interface Toolkit). This layer...
-
An application supporting the educational process of the respiratory system obstructive diseases detection
PublicationThe paper presents a description of functioning of a platform supporting the detection of obstructive diseases in the respiratory system education process. A 16-parameter model of the respiratory system simulated in the MATLAB/Simulink environment was set in the role of the tested patient. It has been linked to the control layer, developed in the LabVIEW environment, using the SIT library (Simulation Interface Toolkit). This layer...
-
Design and Optimization of a Compact Super-Wideband MIMO Antenna with High Isolation and Gain for 5G Applications
PublicationThis paper presents a super-wideband multiple-input multiple-output (SWB MIMO) antenna with low profile, low mutual coupling, high gain and compact size for microwave and millimeter wave (mm-wave) fifth-generation (5G) applications. A single antenna is a simple elliptical-square shape with a small physical size of 20 × 20 × 0.787 mm3. The combination of both square and elliptical shapes results in an exceptionally broad impedance...
-
Elderly persons professional activity - substantive issues and methodical challenges
PublicationPopulation ageing and mass withdrawal of persons around retirement age from the labour market constitutes a serious threat for European Union economy, especially in the so-called new member states. The coming years are expected to bring a considerable increase in public spending on pensions and health care, as well as changes in the structure and size of consumer demand and an increase in the number of socially excluded individuals....
-
Communication as a Factor Limiting University-Business Cooperation
PublicationObjective - Despite the broad extent of the scientific activity dealing with university-business cooperation, Poland has yet to develop a satisfactory cooperation strategy that takes business needs into account. This issue is still relevant due to the need for continuous improvement and resulting benefits aimed at improving enterprise competitiveness. Methodology/Technique - Authors of this article attempt to select an overriding...
-
Adaptive stochastic and hybrid nonlinear optimization algorithms for improving the effectiveness of the biological processes at WWTP
PublicationWastewater treatment plays an important factor in the modern world. Insufficient treatment may result in environmental pollution which can further lead to disasters and diseases. However, processes that take place inside wastewater treatment plants (WWTP) are highly complex in nature, therefore it is difficult to design an efficient, optimal control system. The problem regarding biochemical reactions inside Sequential Batch Reactor...
-
Exploring Impact of Requirements Engineering on Other IT Project Areas – Case Study
PublicationRequirements Engineering (RE) is recognized as one of the most important (yet difficult) areas of software engineering that has a significant impact on other areas of IT projects and their final outcomes. Empirical studies investigating this impact are hard to conduct, mainly due to the great effort required. It is thus difficult for both researchers and industry practitioners to make evidence-based evaluations about how decisions...
-
An Experimentally Aided Operational Virtual Prototyping to Obtain the Best Spindle Speed during Face Milling of Large-Size Structures
PublicationAbstract: The paper presents an original method concerning the problem of vibration reduction in the general case while milling large-size and geometrically complex details with the use of an innovative approach to the selection of spindle speed. A computational model is obtained by applying the so-called operational approach to identify the parameters of the workpiece modal model. Thanks to the experimental modal analysis results,...
-
Microfluidic SIW-Based Tunable Self-Diplexing Antenna for Sub-6 GHz Band Applications
PublicationThis work introduces a novel frequency tunable self-diplexing antenna (SDA) design based on substrate integrated waveguide (SIW) technology. A modified A-shaped slot is employed on the cavity’s top plane, which is excited by two independent 50 Ω microstrip feed lines to operate at each resonant frequency. The frequency flexibility of the proposed antenna allows for fine-tuning at each resonance frequency. The frequency flexibility...
-
Adapting new tools of urban freight management based on Gdynia’s dedicated delivery bays example – an analysis of the process
PublicationThe article presents an analysis of a process which ultimately helped Gdynia to designate pilot delivery sites in its downtown area using international experience. A verification was conducted of policy transfer theory and its practical implementation based on an URBACT Freight Tails project. While the choice of the solution was based on critical analysis of existing practical examples, it needed to be adapted to the local conditions...
-
Threat intelligence platform for the energy sector
PublicationIn recent years, critical infrastructures and power systems in particular have been subjected to sophisticated cyberthreats, including targeted attacks and advanced persistent threats. A promising response to this challenging situation is building up enhanced threat intelligence that interlinks information sharing and fine-grained situation awareness. In this paper a framework which integrates all levels of threat intelligence...
-
Influence of sensor design and optical properties of tissue on the photoplethysmographic signal
PublicationPhotopletysmography and an associated technique called pulse oximetry are still explored due to the expectations that they give a lot of information about the state of the patient and, also, due to the fact that they are non invasive. Knowledge about the impact of various parameters on the measured signal leads to a faster and a more reliable way of analyzing measurement results and finding the dependencies between the involved...
-
Effect of band gap on power conversion efficiency of single-junction semiconductor photovoltaic cells under white light phosphor-based LED illumination
PublicationOn the basis of the detailed balance principle, curves of efficiency limit of single-junction photovoltaic cells at warm and cool white light phosphor-based LED bulbs with luminous efficacy exceeding 100 lm/W have been simulated. The effect of energy band gap and illuminance on the efficiencies at warm and cool light is discussed. The simulations carried out show that maximum power conversion efficiency at 1000 lx reaches 52.0%...
-
Flow Analysis of a Kaplan Turbine
PublicationThis monograph is a guide to a method of experimental and numerical flow investigations for Kaplan - type turbines. The numerical calculations were compared with the test results of the model Kaplan turbine. The tests were carried out on the model test rig in the Gdańsk University of Technology. The turbine has been thoroughly experimentally investigated, resulting in the identification of optimum setting combination of the stator...
-
RAGE as a Novel Biomarker for Prostate Cancer: A Systematic Review and Meta-Analysis
PublicationThe receptor for advanced glycation end-products (RAGE) has been implicated in driving prostate cancer (PCa) growth, aggression, and metastasis through the fueling of chronic inflammation in the tumor microenvironment. This systematic review and meta-analysis summarizes and analyzes the current clinical and preclinical data to provide insight into the relationships among RAGE levels and PCa, cancer grade, and molecular effects....
-
VIBRATION SURVEILLANCE DURING MILLING OF FLEXIBLE DETAILS WITH A USE OF THE ACTIVE OPTIMAL CONTROL
PublicationThe main goal of modern machining operations is to achieve increasingly better performance. High Speed Machining and/or High Performance Cutting, despite a lot of advantages, have also some drawbacks, for example, a possibility of losing stability and development of self-excited chatter vibration. This paper presents an approach of vibration surveillance during high speed milling with a use of active optimal control. Non-stationary...
-
Głowice optoelektroniczne bezzałogowych środków latających
PublicationBezzałogowe środki latające nie wymagają długiego i kosztownego szkolenia załóg. Koszty ich wdrożenia są wielokrotnie niższe od załogowych środków latających. Bezzałogowe środki latające są następcami załogowych pojazdów latających rozpoznawczych i obserwacyjnych. Jednym z podstawowych elementów wyposażania bezzałogowego środka latającego jest głowica optoelektroniczna. Głowice wyposażone są w systemy rejestracji i śledzenia wskazanych...
-
Effect of package type on selected parameters of nutritional quality of chill-stored white sauerkraut
PublicationBrassica vegetables, including white cabbage, both fresh and sour (Brassica oleracea L. var. capitata L.), contain a lot of valuable metabolites which are effective in chemoprevention of cancer as documented by numerous studies. This work investigates the effect of different packaging types; low density polyethylene (PE-LD) and metalized polyethylene terephthalate (PET met/PE) with polyethylene bags on selected quality parameters in...
-
Analysis and bioanalysis: an effective tool for data collection of environmental conditions and processes
PublicationReliable information that allows us to estimate the state of the environment and to forecast changes in the ecosystem are constantly required. Increasing environmental consciousness and dynamic development of analytical techniques are the main reasons for determining the wide range of pollutants occurring at very low concentrations in complex matrix samples. The presence and concentration of many of those pollutants in the environment...
-
Playing the Sprint Retrospective: A Replication Study
PublicationThe Sprint Retrospective is a vehicle for continuous process improvement. Even though it is a well established agile practice, running effective retrospective meetings is challenging. There have been a lot of identified problems that commonly occur during these meetings. To address them, Przybyłek & Kotecka [20] successfully revitalized retrospective meetings by adopting collaborative games, which represent a powerful tool in improving...
-
Progress in module design for membrane distillation
PublicationThere have been tremendous advances in membrane distillation (MD) since the concept was introduced in 1961: new membrane designs and process configurations have emerged, and its commercial viability has been evaluated in several pilot-scale studies. However, its high energy consumption has hindered its commercialization. One of the most promising ways to overcome this obstacle is to develop more energy-efficient membrane modules....
-
Mobile Cloud computing architecture for massively parallelizablegeometric computation
PublicationCloud Computing is one of the most disruptive technologies of this century. This technology has been widely adopted in many areas of the society. In the field of manufacturing industry, it can be used to provide advantages in the execution of the complex geometric computation algorithms involved on CAD/CAM processes. The idea proposed in this research consists in outsourcing part of the load to be com- puted in the client machines...
-
Circularly Polarized Metalens Antenna Design for 5G NR Sub-6 GHz Communication Systems
Publication5G NR (new radio) FR1 range refers to as Sub-6GHz band (410MHz to 7125MHz and 3.4GHz to 6GHz). In this paper, the frequency range of interest is from 3.4 to 6GHz, as many cellular companies are focusing on this Sub-6GHz band. A wideband circularly polarized (CP) antenna radiator is designed with diamond shape patches, fed by a microstrip line at the bottom through a rectangular shape wide slot on a ground plane. The proposed CP...
-
Frequency-Reconfigurable Hybrid SIW-Based Self-Diplexing Antenna Using Solid and Liquid Dielectric Loading
PublicationThis paper presents a novel frequencyreconfigurable self-diplexing antenna (SDA) utilizing a hybrid substrate-integrated waveguide (SIW). The antenna comprises a radiating slot, a feeding network, and a hybrid SIW cavity featuring half-mode circular and half-mode rectangular SIW structures. The unique feature of this antenna lies in its fine-tuning capability of each resonant frequency by inserting or injecting solid and liquid...
-
Consciousness Study of Subjects with Unresponsive Wakefulness Syndrome Employing Multimodal Interfaces
PublicationThe paper presents a novel multimodal-based methodology for consciousness study of individuals with unresponsive wakefulness syndrome. Two interfaces were employed in the experiments: eye gaze tracking system – CyberEye developed at the Multimedia Systems Department, and EEG device with electrode placement in the international 10-20 standard. It was a pilot study for checking if it is possible to determine objective methods based...
-
The role of SSVF and SSHF beds in concentrated wastewater treatment, design recommendation
PublicationThe return flows of reject water from sewage sludge dewatering alter the activated sludge process ina conventional WWTP and increase TN concentration in the final effluent from WWTP. The objectiveof the investigation carried out was to consider the application of multistage treatment wetland(MTW) for the treatment of reject water from sewage sludge dewatering in a centrifuge (RWC). Thispaper aims to present the design and performance...
-
An incorporation of contemporary daylight assessment methods into architecture and urban planning of residential areas in Poland
PublicationThis paper presents the preliminary results of the ongoing research focusing on daylight design methods for the urban planning of residential areas in Poland. The purpose of this research is to find out if modern daylight performance metrics and design methods can be beneficial to the process of urban residential planning. The paper presents a review of daylight guidelines derived from historic, Polish building regulations. A summary...
-
Implementation of Weigh-in-Motion System in Freight Traffic Management in Urban Areas
PublicationThe article presents how the Weigh-in-Motion system can be used for managing Gdynia’s freight traffic. Potential sites for weight pre-selection were identified in an analysis of the technical and location conditions. Situated directly in the east part of the Port of Gdynia a site was selected for a pilot implementation. Theoretical scenarios were simulated using an extended WIM system as a tool for controlling access to selected...
-
Towards a Lightweight Approach for the Evaluation of Requirements Engineering Impact on Other IT Project Areas
PublicationRequirements Engineering (RE) is recognized as one of the most important, but difficult areas of software engineering, with a significant impact on other areas of the IT project and its final outcome. The empirical studies investigating this impact are hard to conduct, mainly due to large effort required. It is thus difficult for researchers and even more for industry practitioners to make evidence-based evaluations, how decisions...
-
Efficiency of linear and non-linear classifiers for gas identification from electrocatalytic gas sensor
PublicationElectrocatalytic gas sensors belong to the family of electrochemical solid state sensors. Their responses are acquired in the form of I-V plots as a result of application of cyclic voltammetry technique. In order to obtain information about the type of measured gas the multivariate data analysis and pattern classification techniques can be employed. However, there is a lack of information in literature about application of such...
-
A Study of Mutual Coupling Suppression between Two Closely Spaced Planar Monopole Antenna Elements for 5G New Radio Massive MIMO System Applications
Publication5G NR (new radio) introduces the concept of massive MIMO (multiple-input-multiple-output) technology, in which a larger number of antenna arrays are installed on the transceiver. Due to the increased number of antenna elements allocated close to each other (approximately at half-wavelength distance), mutual coupling becomes a serious problem leading to performance degradation of the MIMO communication system. In this communication,...
-
Simulations of hydro-fracking in rock mass at meso-scale using fully coupled DEM/CFD approach
PublicationThe paper deals with two-dimensional (2D) numerical modelling of hydro-fracking (hydraulic fracturing) in rocks at the meso-scale. A numerical model was developed to characterize the properties of fluid-driven fractures in rocks by combining the discrete element method (DEM) with computational fluid dynamics (CFD). The mechanical behaviour of the rock matrix was simulated with DEM and the behaviour of the fracturing fluid flow...
-
Good practices in requirements, project and risk managment in educational IT projects
PublicationOne can find many learning aids and simulations of physical phenomena on the market - provided as a standalone application or as part of an educational package. However, only a few of them allow for the building of interactive experiments: experiments similar to those that should be conducted in physics laboratories at schools. Gdańsk University of Technology decided to fill this market niche by designing and constructing a set...