displaying 1000 best results Help
Search results for: 18NI300 STEEL
-
Guided wave propagation in diagnostic of steel elements
PublicationThis paper is devoted to numerical investigations of elastic wave propagation in steel elements. The aim of this study is to conduct numerical analysis and experimental investigations on the propagation of elastic waves in steel elements in the context of damage detection. In particular, this paper is devoted to detection of damage occurring in the form of notch or changed thickness. This approach utilized the fact that any discontinuities...
-
Uniform corrosion monitoring of carbon steel in concrete.
PublicationW przypadku korozji prętów zbrojeniowych w żelbecie zaobserwowane zostały obszary wzmożonego zaatakowania. Pomiar prądowego i napięciowego szumu elektrochemicznego umożliwia wyznaczenie szybkości korozji ogólnej a zmiany parametrów statystycznych przebiegów szumowych umożliwiają detekcję występowania przestrzennych rejonów intensyfikacji korozji. Przedstawione rezultaty, oparte na wykorzystaniu odpowiedniego układu zastępczego,...
-
Pitting corrosion in steel and electrochemical noise intensity
PublicationPrzedstawiono analizę szumu elektrochemicznego, rejestrowanego w obecności korozji wżerowej. Stwierdzono korelację pomiędzy intensywnością szumu a ubytkiem mas elektrod stalowych. Rejestry szumowe rozłożone zostały na składowe częstotliwościowe za pomocą przekształcenia falkowego. Dla pewnych składowych stwierdzono silniejszą korelację z ubytkiem mas korodujących elektrod. Pasmo częstotliwościowe powyższych składowych odpowiada...
-
Analysis of wave propagation in a bolted steel joint
PublicationThe paper presents results of numerical and experimental investigations of elastic wave propagation in a bolted single-lap joint. The research was carried out for both symmetric and antisymmetric Lamb wave modes. In experimental studies the PZT transducers were used to excite and register wave propagation signals. The controlled value of the torque during measurements was ensured by the use of high precision torque wrenches. Numerical...
-
Recent steel structures in Poland - the selected projects
PublicationThe paper presents selected examples of recently completed steel structures in Poland. These are roofs over sport stadiums, construction of public buildings and bridges. Described examples do not exhaust the acquis in the field of steel constructions in Poland. The authors, however, may hope that the presented con-structions represents current achievements in Poland in the field of steel structures.
-
Sliding burnishing technology of holes in hardened steel
PublicationNew technology with sliding burnishing of holes with cylindrical surface, made of hardened steel /60 HRC/, is presented in the paper.After burnishing operation on hole diameter 30 mm in satellite gear wheel the surface roughness parameter Ra=0,02-0,04 micrometers was obtained. The method and results of research as technological conclusion are presented.
-
Reduction of steel chimney vibrations with a pendlum damper.
PublicationKarman vortices observed around chimneys may induce dangerous structural vi-brations at certain wind velocities. The aim of this paper is to analyse theeffectiveness of pendulum damper in vibration reduction of a steel chimney. A two degree-of-freedom system is used to model the behaviour of the struc-ture equipped with a damper. The results of the study show that the use of pendulum with tuned frequency leads to significant...
-
Hydrogen charging of nitrided steel in acid solution
PublicationKonstrukcyjną stal, azotowaną w wyładowaniu jarzeniowym w mieszaninie gazów o różnej zawartości N2, H2 i Ar, poddawano katodowemu nawodorowaniu w kwaśnym roztworze, imitującym przepracowany olej maszynowy. W pomiarach szybkości przenikania wodoru i ekstrakcji próżniowej określano wpływ azotowanych warstw, odpowiednio, na transport wodoru i na jego nieodwracalne pułapkowanie. W obecności niezdefektowanej warstwy kompaktowych azotków...
-
Weldability of high strength steel in underwater environment
PublicationThe article describes the problems with weldability of high-strength steels in the aquatic environment. The tendency of steel S355J2G3 and S500M to form cold cracks when welded in wet welding conditions has been experimentally evaluated. It was found that the tested steels have a high propensity to cracking. An experiment has been proposed and tested to evaluate the usefulness of the tempering bead technique as a method of improving...
-
Buckling analysis of cold formed steel column
PublicationW pracy przedstawiono analizę słupa zimnogiętego o przekroju otwartym. Przeprowadzono analizy statyczne liniowe i nieliniowe. Analizowano wpływ podłoża sprężystego oraz sztywność połączenia dwóch sąsiednich słupów.
-
Aesthetic perception of steel-glass architecture in Japan
PublicationAesthetic perception of steel-glass architecture in Japan
-
Estimation of nonstructural stiffness in instrumented steel frames
PublicationLateral stiffness of nonstructural components may significantly influence the initial stiffness of the entire structure and consequently alter its dynamic characteristics. While methods for simulating structural members are well-established, approaches for modeling nonstructural components that also participate in seismic response are notably less developed. In this paper a simplified, physically-intuitive approach for estimating...
-
Underwater Local Cavity Welding of S460N Steel
PublicationIn this paper, a comparison of the mechanical properties of high-strength low-alloy S460Nsteel welded joints is presented. The welded joints were made by the gas metal arc welding (GMAW)process in the air environment and water, by the local cavity welding method. Welded joints were testedfollowing the EN ISO 15614-1:2017 standard. After welding, the non-destructive—visual, penetrant,radiographic, and ultrasonic (phased array) tests...
-
ENGINEERING JOURNAL-AMERICAN INSTITUTE OF STEEL CONSTRUCTION INC
Journals -
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN
Journals -
Heat tint colours on stainless steel and welded joints
PublicationSurface layer condition of stainless steels and welded joints influences strongly their corrosion resistance. This problem seems to be underestimated. This current study explains the phenomenon of heat tint forming on welds, the methods of its removal, inspection procedures after heat tint removing and post weld finishing
-
The effect of the concentration of steel fibres on the properties of industrial floors
Publication -
Selected problems on application of steel sandwich panels to marine
PublicationW pracy przedstawiono wybrane problemy stosowania stalowych laserowo spawanych paneli w konstrukcji statku. Problemy te wynikają ze specyfiki cienkiej, spawanej laserowo konstrukcji stalowej i obejmują szerokie spektrum zagadnień począwszy od własności wytrzymałościowychy elementarnego połączenia teowego spawanego laserowo poprzez łączenie paneli ze sobą a skończywszy na integracji paneli z konstrukcją tradycyjną.
-
The influence of dimensional accuracy on steel structures cost calculation
PublicationW referacie przedstawiono zależność pomiędzy wartością tolerancji a kosztami wytwarzania budowlanych konstrukcji stalowych. Opisano zasady klasyfikacji tolerancji prętowych konstrukcji stalowych z uwagi na porawny montaż konstrukcji wyrażony równaiem pętli montażowej. Przedstawiono podstawy analizy i syntezy tolerancji oraz zaproponowano nową formułę optymalizacji kosztów wytwarzania. Wskazano metody rozwiązania zadania optymalizacyjnego.
-
Evaluation of 316L porous stainless steel for SOFC support
PublicationW pracy przedstawiono wyniki badań stali typu 316L związanych z zastosowaniem w tlenowych ogniwach paliwowych.
-
Application of Numerical Simulations on 10GN2MFA Steel Multilayer Welding
Publication -
Numerical Simulations of X22CrMoV12-1 Steel Multilayer Welding
Publication -
Practical Application of the Industry 4.0 Concept in a Steel Company
Publication -
PROBLEMS WITH CORROSION PROTECTION STEEL STACKS IN FGD SYSTEMS
PublicationThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at a stack which discharges flue gas before wet lime/limestone desulphurization. A very rapid soaking of spherical infill vinylester coating with electrolyte has been observed....
-
THE INFLUENCE OF POLYMER STRIPS IN REDUCTION OF A STEEL GRANDSTAND VIBRATIONS
PublicationGrandstands are types of structures commonly used during sport events or music concerts. Dynamic loads generated by crowd movement may have significant influence on human perception as well as may lead to the destruction of a structure. Lighter and more slender structural steel members are more easily excitable by spectators. If the synchronized movement is tuned with the natural frequency of the affected part of the structure,...
-
Earthquake-induced pounding between asymmetric steel buildings
PublicationEarthquake-induced pounding between buildings has been the subject of numerous numerical and experimental studies in the resent years. The phe-nomenon may cause severe damage to structural elements as well as may also lead to the total collapse of colliding structures. A major reason leading to pounding between adjacent, insufficiently separated buildings results from the differences in their dynamic properties. The aim of this...
-
Modification of cement-ash composites with steel fibre addition
PublicationPraca zawiera wyniki badań kompozytów cementowo-popiołowych, w których popiół zastosowano jako częściowy zamiennik cementu. Do kompozytów dodano niewielkie ilości dwóch rodzajów włókien stalowych. Zbadano właściwości techniczne kompozytów. Wytrzymałości kompozytów cementowo-popiołowych z włóknami stalowymi w stosunku do wytrzymałości kompozytów bez włókien po wszystkich okresach wiązania i twardnienia były wyższe od kilku do kilkudziesięciu...
-
Fatigue properties of laser welded steel sandwich panel.
PublicationPrzedstawiono wyniki badań laboratoryjnych paneli SANDWICH, prowadzonych w Kat. TOiOO Wydz. OiO na konstrukcjach w skali rzeczywistej. Przedstawiono program badań, omówiono założenia procedur badawczych i konstrukcję stanowisk testowych. Dokonano porównania uzyskanych rezultatów z wynikami prezentowanymi w literaturze. Przedstawiono propozycję algorytmu szacowania trwałości zmęczeniowej konstrukcji spawanych laserowo.
-
Experimental tests of steel double-type balcony connections
PublicationThe paper presents analysis and results of experimental tests of full scale prefabricated balcony sets with dimensions (width × length × height): 2.0 m × 2.78 m × 0.186 m (in slope to 0.17 m). The sets consists of reinforced concrete slabs (balcony and ceiling) connected with each other by double-type balcony connections. The paper analyses the impact of variable parameters on the load carry capacity of elements. Additionally...
-
Reservoir Influence on Pressure Wave Propagation in Steel Pipes
PublicationThe relation between the length of steel pipe and the pressure wave period in the system, reservoir-pipe-valve, is discussed. Experiments carried out for the short steel pipes showed that in such a system, the pressure wave celerity estimated using the measured wave cycles systematically increases with the increase of the pipe length. The observed differences can exceed even 90 m=s. As the pressure wave traveling in the pipe with...
-
Cavitation Erosion of P110 Steel in Different Drilling Muds
PublicationThe P110 steel specimens were subjected to ultrasonic cavitation erosion in different compositions of drilling muds and surfactant additive. The test procedure was based on ASTM-G-32 standard recommendations. API 5CT-P110 steel is used for pipes in oil and gas industry. The harsh environment and high velocity of flows poses corrosive and erosive threat on materials used there. The composition of drilling fluid influences its rheological...
-
Effectiveness of Concrete Reinforcement with Recycled Tyre Steel Fibres
Publication -
COLD CRACKING OF S460N STEEL WELDED IN WATER ENVIRONMENT
PublicationThis paper shows results of weldability testing of fine-grained high -strength low- alloy S460N steel welded in water environment by covered electrodes. The tests were carried out by using the CTS test specimens with fillet welds. Four specimens were welded under water and one specimen in air. Welded joints were subjected to non-destructive visual and penetration tests. The accepted joints were then subjected to macroscopic and...
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublicationThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Earthquake-Induced Pounding Between Asymmetric Steel Buildings
PublicationEarthquake-induced pounding between buildings has been the subject of numerous numerical and experimental studies in the resent years. The phenomenon may cause severe damage to structural elements as well as may also lead to the total collapse of colliding structures. A major reason leading to pounding between adjacent, insufficiently separated buildings results from the differences in their dynamic properties. The aim of this...
-
APPLICATION POSSIBILITIES OF THE S960 STEEL IN UNDERWATER WELDED STRUCTURES
PublicationIn this paper, the application possibilities of the ultra-high strength (UHSS). Domex 960 steel in the underwater welded structures are analyzed. In the research, the investigated material has been tested in bead-on-plate wet welding conditions with the usage of different heat input values, namely 0.63 kJ/mm, 0.72 kJ/mm and 0.93 kJ/mm. Specimens were performed by the manual metal arc (MMA) welding method with the usage of rutile...
-
Axial capacity of steel built-up battened columns
PublicationThis paper deals with the numerical investigation aimed to study the axial capacity of pin-ended steel built-up columns. Three methods of calculating forces in chords and batten, taking into account the material and geometric imperfections specified in the Eurocode 3 are considered. The aim of this study was to compare different methods allowing the calculation of the column load capacity and determine a simpler and faster method...
-
Bead-on-Plate Underwater Wet Welding on S700MC Steel
PublicationThe participation of high strength steels in marine and offshore structures is increasing, which makes it necessary to develop recommendations for underwater repair welding works. The article presents the results of bead-on-plate welded specimens made of S700MC high strength steel in underwater wet welding conditions by covered elec- trodes. Three specimens with heat input values in the range 0.91-1.05 kJ/mm were made. The specimens...
-
Corrosion degradation impact on mechanical properties of structural steel
PublicationRecently, extensive research was conducted regarding the impact of corrosion degradation on the mechanical properties of structural steel. Studies show that at the material level, the microstructure is somewhat unchanged due to corrosion degradation. However, the corrosion causes pits and structural surface irregularities that consequently impact the mean stress-strain response of typical coupon specimens subjected to tensile loading....
-
INFLUENCE OF CERAMIC COATING ON MECHANICAL PROPERTIES OF STAINLESS STEEL
PublicationCrystal structure and phase composition of stainless steel substrates (AISI 304 type) was studied and it was found that they adopted the cubic symmetry. The calculated elementary cell parameter for the mayor Fe-Ni phase (weight fraction 99%) was a = 3.593 Å, whereas the mean grain size was = 2932 Å. Morphology of the stainless steel substrate surface was studied with profilometry. Mechanical properties of the stainless steel...
-
Degradation of ferritic X10CrAlSi18 stainless steel caused by slurry
PublicationThe slurry erosion tests of ferritic X10CrAlSi18 steel were carried out using a slurry pot device. In order to investigate the erosion process, two series of tests were performed: first one with a constant impact velocity of 5 m/s, 7 m/s and 9 m/s and the second one, during which the impact velocity was changed after every exposure. During each test, an influence of test conditions on volume loss, surface hardness and roughness...
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublicationThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Adhesion of organic coatings to hot-dip galvanized steel
PublicationDuplex systems provide long-time corrosion protection, much longer than the sum of the lifetimes of zinc and paint used individually. However loss of adhesion between coating and zinc substrate is often found in practice. Different methods of zinc surface preparations are used in the fi eld. The aim of this study was to examine and compare coating protection when the old zinc surface, stored during long-time period (15 years) in...
-
Modeling the application of steel slag in stabilizing expansive soil
PublicationThe objective of this study was to evaluate the suitability of steel slag as an additive to the engineering properties of weak clay soil. Different geotechnical laboratory tests were conducted on both stabilized and natural soils. Steel slag (SS) was added at a rate of 0, 5, 10, 15, 20, and 25% to the soil. Specific gravity, grain size analysis, Atterberg limit test, compaction test, free swell, California bearing ratio (CBR),...
-
Steel-fibrous concrete -experiments and a numerical discrete model
PublicationW książce przedstawiono wyniki doświadczalne i numeryczne dotyczące rys w elementach betonowych wzmocnionych włóknami stalowymi dla różnych problemów brzegowych quasi-statycznych. Obliczenia wykonano przy zastosowaniu własnego oryginalnego modelu sieciowego. W modelu beton z włóknami stalowymi był modelowany na poziomie mezo. W obliczeniach uwzględniono strefy kontaktu miedzy kruszywem a zaczynem oraz włóknami a zaczynem.
-
Fatigue behaviour of SLM maraging steel under variable-amplitude loading
PublicationOne of the most challenging issues for additive manufactured materials is fatigue endurance. Engineering components often operate under complex, variable amplitude loadings, in which existing technological imperfections promote fatigue cracks growth and damage of elements eventually. In this study the effects of different variable-amplitude strain levels on fatigue life, 18Ni300 steel was tested. The work presents various behaviours...
-
A dissimilar welded joint of grade 92 steel and AISI 304L steel obtained using IN82 buttering and IN617 fller: relationship of microstructure and mechanical properties
PublicationUnfavourable operating conditions of equipment in the energy industry resulting from high-temperature loads determine the need to use special materials and technological solutions, including welding procedures. In this article, buttering using IN82 (ERNiCr-3) consumables was proposed as a method to improve the weldability of grade 92 steel joined by the gas tungsten arc welding (GTAW) process with AISI 304L (IN617 fller). The...
-
Search for optimum geometry of selected steel sandwich panel joints
PublicationZastosowanie stalowych paneli typu sandwich w konstrukcjach okrętowych wymaga rozwiązania wielu problemów. Jednymi z trudniejszych zagadnień związanych z tymi nowymi strukturami są połączenia pomiędzy panelami oraz między panelami i konstrukcją innego typu. Artykuł przedstawia poszukiwanie optymalnej geometrii połączenia typu panel-panel w układzie wzdłużnym, przy użyciu parametrycznego modelu w programie ANSYS. Poszukiwano konfiguracji...
-
The influence of plastic deformation on the magnetoelastic properties of the CSN12021 grade steel
PublicationWłasności magnetosprężyste materiałów są silnie modyfikowane przez zmiany struktury dyslokacyjnej, które są wynikiem procesów deformacji plastycznej. Zmiany te mogą być wykorzystane jako podstawa do opracowania metody nieniszczącej oceny stopnia deformacji materiału.Jak dotychczas zaproponowane zostały różne metody, oparte na pomiarach pętli histerezy magnetycznej czy też natężenia magnetycznego efektu Barkhausena. Artykuł porównuje...
-
Thermal Fatigue Influence of Laser Treated Tool Steel Surface
Publication