Search
displaying 1000 best results Help
Search results for: BIOPOLYOLTHERMAL PROPERTIES
-
The effect of nanoparticles size on photocatalytic and antimicrobial properties of Ag-Pt/TiO2 photocatalysts
PublicationAg-Pt-modified TiO2 nanocomposites were synthesized using the sol–gel method. Bimetallic modified TiO2 nanoparticles exhibited improved photocatalytic activity under visible-light irradiation, better than monometallic Ag/TiO2 and Pt/TiO2 nanoparticles (NPs). All modified powders showed localized surface plasmon resonance (LSPR) in visible region. The photocatalysts’ characteristics by X-ray diffractometry (XRD), scanning transmission...
-
Superconducting properties of vn-sio 2 sol-gel derived thin films
Publicationin this work studies of structure and superconducting properties of vnsio2 films are reported. the films were obtained through thermal nitridation (ammonolysis) of solgel derived v2o3sio2 coatings (in a proper v2o3/sio2 ratio) at 1200 ◦c. this process leads to the formation of disordered structure with vn metallic grains dispersed in the insulating sio2 matrix. the structural transformations occurring in the lms as a result...
-
The influence of selenium addition during seeds' germination on the biological properties of obtained sprouts
PublicationSelenium plays a vital role in human body, because in the form of aminoacids (Se-methionine, Se-cysteine) it is found in the active centres of over 25 enzymes, including those regarded as 'cytoprotective'. Unfortunatelly, its daily intake in Poland and other European countries is lower than predicted by dietary recommendations. The consequences of selenium deficiency in diet might be severe, including higher susceptibility to cardio-vascular...
-
The mechanical properties of biopolyether-urethanes synthesized from bioglycols and hydroxylated soybean oil
PublicationArtykuł zawiera informcje dotyczące syntezy biopolietero-uretanów z uzyciem biokomponentów oraz porównanie wpływu przedłużaczy łańcucha polimerowego na właściwości mechaniczne i termomechaniczne wytworzonych materiałów.
-
Comparision of mechanical properties of nitrided cases and remelted layers of austenitic stainless steel
Publication -
Properties of recombinant trehalose synthase from Deinococcus radiodurans expressed in Escherichia coli
PublicationA trehalose synthase gene from Deinococcus radiodurans(DSMZ 20539)containing 1659 bp reading frame encoding 552 amino acids was amplified using PCR. The gene was finally ligated into pET30Ek/LIC vector and expressed after isopropyl β-d-thiogalactopyranoside induction in Escherichia coli (DE3) Rosetta pLysS. The recombinanttrehalose synthase (DraTreS) containing a His6-tag at the C-terminus was purified by metal affinity chromatography...
-
The influence of temperature on properties of the polymer flexible joint used for strengthening historical masonries
PublicationA new method of repairing damaged structures by filling the cracks with a specially prepared elastomeric polymer mass has been recently proposed. This new and innovative technique, known as the Flexible Joint Method (FJM), is mainly dedicated to masonries and historical objects, where minimum intervention is permitted. The flexible joint bonds the disrupted elements and ensures further safe exploitation of a damaged structure....
-
Fabrication and structural properties of Y and Fe co-doped SrTiO3 nanoceramics for SOFC
PublicationYttria and iron co-doped strontium titanate perovskites, (Y0,07Sr0,93Ti1-xFexO3-δx=0,1; 0,2) samples were fabricated by two methods: solid-state synthesis (SS) and the Pechinisol-gel modified method. The morphology of samples were measured by SEM and X-raydiffraction. Results were compared and discussed. The strong relationship between fabricationprocedure and microstructure has been proven. It was also observed, that the nanoceramicsobtained...
-
Ship course control system taking into account the steering gear dynamic properties
PublicationW artykule zostały przedstawione różne konfiguracje regulatorów nieliniowych do sterowania kursem statku. Zaprojektowane regulatory oparto na metodzie backstepping, regulatorze PD oraz sterowaniu ślizgowym. Algorytmy uwzględniają na etapie projektowania liniowe własności dynamiczne urządzenia wykonawczo - sterującego maszyny sterowej. Dokonano analizy porównawczej jakości pracy rozpatrywanych struktur sterowania podczas badań symulacyjnych...
-
Residual Effects of Different Cropping Systems on Physicochemical Properties and the Activity of Phosphatases of Soil
Publication -
2D numerical simulation of tear film dynamics: Effects of shear-thinning properties
Publication -
INFLUENCE OF THE INTERMOLECULAR INTERACTION ON PHYSICO-CHEMICAL PROPERTIES OF CHITOSAN/HYALURONIC ACID BLENDS
Publication -
Surface properties tuning of exfoliated graphitic carbon nitride for multiple photocatalytic performance
Publication -
Physicochemical and rheological properties of lentil milk/inulin blend—A feta cheese analogue
Publication -
Properties of the Langmuir and Langmuir–Blodgett monolayers of cholesterol-cyclosporine A on water and polymer support
Publication -
On the Effect of Non-Thermal Atmospheric Pressure Plasma Treatment on the Properties of PET Film
Publication -
Calcification Alters the Viscoelastic Properties of Tendon Fascicle Bundles Depending on Matrix Content
Publication -
Antioxidant properties and resveratrol content of Polish Regent wines from Podkarpacie region
Publication -
Interfacial properties of PET and PET/starch polymers developed by air plasma processing
Publication -
Properties of PEEK-supported films of biological substances prepared by the Langmuir-Blodgett technique
Publication -
Investigation of the Electrokinetic Properties of Paraffin Suspension. 2. In Cationic and Anionic Surfactant Solutions
Publication -
New Chalcone Derivatives Containing 2,4-Dichlorobenzenesulfonamide Moiety with Anticancer and Antioxidant Properties
Publication -
Few-Layered Hexagonal Boron Nitride: Functionalization, Nanocomposites, and Physicochemical and Biological Properties
Publication -
Influence of Firing Temperature on Phase Composition and Color Properties of Ceramic Tile Bodies
Publication -
The effect of elevated temperature on the properties of cement mortars containing nanosilica and heavyweight aggregates
Publication -
Bulk quantity and physical properties of boron nitride nanocapsules with a narrow size distribution
Publication -
Effect of sol composition on the properties of TiO2 powders obtained by the sol-gel method
Publication -
Mechanical Properties and Strength Reliability of Impregnated Wood after High Temperature Conditions
Publication -
Silver filled single-wall carbon nanotubes—synthesis, structural and electronic properties
Publication -
Enhanced thermal properties of poly(lactic acid)/MoS2/carbon nanotubes composites
Publication -
Effect of brookite on the photocatalytic properties of mixed-phase TiO2 obtained at a higher temperature
Publication -
Hexagonal Boron Nitride Functionalized with Au Nanoparticles—Properties and Potential Biological Applications
Publication -
Stability and physicochemical properties of model salad dressings prepared with pregelatinized potato starch
Publication -
The Design Development of the Sliding Table Saw Towards Improving Its Dynamic Properties
PublicationCutting wood with circular saws is a popular machining operation in the woodworking and furniture industries. In the latter sliding table saws (panel saws) are commonly used for cutting of medium density fiberboards (MDF), high density fiberboards (HDF), laminate veneer lumber (LVL), plywood and chipboards of different structures. The most demanded requirements for machine tools are accuracy and precision, which mainly depend on...
-
Mechanical and Corrosion Properties of Laser Surface-Treated Ti13Nb13Zr Alloy with MWCNTs Coatings
Publication: Titanium and its alloys is the main group of materials used in prosthetics and implantology. Despite their popularity and many advantages associated with their biocompatibility, these materials have a few significant disadvantages. These include low biologic activity—which reduces the growth of fibrous tissue and allows loosening of the prosthesis—the possibility of metallosis and related inflammation or other allergic reactions,...
-
Impact of reclaimed asphalt pavement (RAP) on low-temperature properties of asphalt concrete
PublicationHot mix recycling is a practice which enables reusing materials from old asphalt pavements. Current Polish regulations allow usage of RAP only for binder and base courses, and its amount is limited. Asphalt mixtures with RAP material have to fulfil requirements stated for typical asphalt mixtures. The research presents low-temperature properties of twelve different asphalt concretes with RAP material, determined using three-point...
-
Effect of Storage Conditions of Rutile Flux Cored Welding Wires on Properties of Welds
PublicationThe influence of storage locations of two grades of rutile flux cored welding wires on their surface condition and the strength of the welds made with them were studied. Wires were stored in real urban conditions (Gdańsk and Katowice) for 1 month, simultaneously recording changes in conditions: temperature and relative humidity of the environment. Visual tests of wires in the delivered and stored condition as well as visual and...
-
Novel ABTS-dot-blot method for the assessment of antioxidant properties of food packaging
PublicationThe new ABTS-dot-blot method for the direct determination of antioxidant activity of active packaging that is in contact with foodstuffs has been developed. The usefulness of the new method was verified with the use of agarose, pork gelatin, bacterial cellulose and cellulose-chitosan films with incorporated standard antioxidant – Trolox or plant phytochemicals derived from three types of berry juices (chokeberry, blue-berried honeysuckle,...
-
Crystal structure and physical properties of AePd1-xP1+x (Ae = Ca, Sr)
PublicationWe report the discovery of two new compounds AePd1-xP1+x (Ae = Ca, Sr) crystallized in different hexagonal structures. Single crystals of AePd1-xP1+x (Ae = Ca, Sr) are obtained using the Bi-flux method. Crystallographic analysis by both powder and single crystal X-ray diffraction shows that CaPd1-xP1+x crystallizes in a non-centrosymmetric hexagonal structure with the space group P-6m2 (No.187) and lattice parameters a = b = 4.0391(9)...
-
Structure and thermoelectric properties of nickel-doped copper selenide synthesised in a hydrogen atmosphere
PublicationNickel-doped copper selenide—Cu2-xNixSe (x = 0; 0.01; 0.02; 0.03)—materials with high thermoelectric properties were synthesised through reduction of reagents in hydrogen. The impact of the nickel content on both the microstructure and thermoelectric properties was examined. The nickel-doped samples’ microstructure differed significantly from pristine copper selenide. Besides Cu2Se, copper precipitations were present in the materials....
-
Experimental and Numerical Investigation of Mechanical Properties of Lightweight Concretes (LWCs) with Various Aggregates
PublicationHigh requirements for the properties of construction materials and activities directed at environment protection are reasons to look for new solutions in concrete technology. This research was directed at solutions affecting the reduction of energy consumption and CO2 emissions. The use of lightweight concretes (LWCs) allows one to meet both conditions at the same time. The purpose of the research presented in this paper was to...
-
Properties of Barium Cerate Thin Films Formed Using E-Beam Deposition
PublicationThis article focuses on the properties of the BaCeO3 thin films formed by electron-beam vapor deposition and investigates the formation of barium cerates on supports with different thermal expansion coefficients (Stainless Steel, Invar, Glass Sealing, and Inconel substrates) and the influence of the technological parameters on the properties of the formed thin films with an emphasis on the stability of the films. Morphology and...
-
The effect of dehydration/rehydration of bacterial nanocellulose on its tensile strength and physicochemical properties
PublicationBacterial nanocellulose (BNC) is a natural biomaterial with a wide range of biomedical applications. BNC contains 99 % of water which makes it too thick to be used as a bioimplant material. The aim of the work was to determine the effect of the BNC dehydration followed by rehydration on its mechanical and physicochemical properties, in the context of the use of BNC as bio-prostheses in the cardiovascular system. Dehydration involved the...
-
Optical and photocatalytic properties of rare earth metal-modified ZnO quantum dots
PublicationA series of novel ZnO quantum dots modified with rare earth metals was successfully prepared by a simple sol-gel approach. The effects of types (Eu, Er, Tb, Yb, Ho, La) and amounts (from 0.09 to 0.45 mmol) of lanthanides on the optical properties, structural characterization and photocatalytic activity of ZnO/RE QDs were systematically investigated. The X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform...
-
Reclaimed Rubber/Poly(ε‐caprolactone) Blends: Structure, Mechanical, and Thermal Properties
PublicationThe amount of elastomeric waste, especially from tires is constantly increasing on a global scale. The recycling of these residua should be considered a priority. Compounding the waste rubbers with other polymers can be an excellent alternative to reuse waste materials. This procedure requires solving the issue of the lack of compatibility between the waste rubber particles and other polymers. Simultaneously, there is a claim for...
-
Static and Dynamic Mechanical Properties of 3D Printed ABS as a Function of Raster Angle
PublicationDue to the rapid growth of 3D printing popularity, including fused deposition modeling (FDM), as one of the most common technologies, the proper understanding of the process and influence of its parameters on resulting products is crucial for its development. One of the most crucial parameters of FDM printing is the raster angle and mutual arrangement of the following filament layers. Presented research work aims to evaluate different...
-
Properties of Nanohydroxyapatite Coatings Doped with Nanocopper, Obtained by Electrophoretic Deposition on Ti13Zr13Nb Alloy
PublicationNowadays, hydroxyapatite coatings are the most common surface modification of long-term implants. These coatings are characterized by high thickness and poor adhesion to the metallic substrate. The present research is aimed at characterizing the properties of nanohydroxyapatite (nanoHAp) with the addition of copper nanoparticle (nanoCu) coatings deposited on the Ti13Zr13Nb alloy by an electrophoresis process. The deposition of...
-
Electrical properties of hybrid planar diode based on palladium phthalocyanine and titanium dioxide
PublicationThis work details experimental studies of a planar diode made of indium tin oxide/titanium dioxide/palladium phthalocyanine/gold. The rectification ratio of current was 105 at 1.5 V. The analysis of the electrical properties of the system was based on small signal complex capacitance spectra measured in the frequency range of 25 Hz-1 MHz at different values of bias. No depletion region at the TiO2/PdPc interface was observed. Forward...
-
Properties of water in the region between a tubulin dimer and a single motor head of kinesin
PublicationA kinesin is a molecular motor that can perform movement on a microtubule track in a stepping-like manner. This motion is connected with processes of association and dissociation of kinesin and tubulin. Water is an important participant in these kinds of molecular interactions. This is why we have decided to investigate the dynamical and structural properties of water in the region between the kinesin catalytic domain and the tubulin...
-
Mechanical properties for preliminary design of structures made from PVC coated fabric
PublicationIn this paper, laboratory tests necessary for the identification of non-linear elastic immediate properties of the PVC coated polyester fabric (like AF 9032) are described. The material parameters are specified on the basis of the uniaxial tensile tests in the warp and weft directions as well as on the base of the biaxial tensile tests. For the identification process techniques based on the least squares method are used. The authors...