displaying 1000 best results Help
Search results for: GFRP COMPOSITE
-
Sustainable utilization of copper post-flotation waste in cement composites
PublicationThe current way of managing the copper ore flotation waste is by placing it in waste neutralization facilities. However, flotation waste has great potential in application in cement composites. The article presents the detailed characteristics of post-flotation waste (PFW) and three types of cements: CEM I, CEM II/B-V, and CEM III/A, 42.5 MPa class. The post-flotation waste added for 20% of the cement mass increase the water demand...
-
Evaluation of high-frequency roughness measurement errors for composite and ceramic surfaces after machining
PublicationPrecise characterisation of surface topography is of the greatest importance since many factors directly affect the accuracy of the whole measurement process. In this paper, the variety of surface topographies from machined composite and ceramic workpieces was studied with a special emphasis on the measurement results. Surfaces were subjected to the ground diamond, honing and milling processes. Measurement results were analysed...
-
A tribological research on a reciprocating sliding contact of aluminum-ferrous composite against cast-iron.
PublicationOpisano badania kompozytów: silumin AlSi11-żelazo albo silumin AlSi11-stal narzędziowa N9 (otrzymanych in situ), a także samego siluminu AlSi11 w skojarzeniu z żeliwem 350, przy tarciu ślizgowym w ruchu posuwisto-zwrotnym. Stwierdzono wpływ sposobu otrzymywania materiału kompozytowego na zużycie i opory ruchu skojarzenia badawczego, w szczególności materiały te zużywały się wolniej, niż silumin AlSi11.
-
Experimental and numerical investigation of mercury removal from flue gas by sorbent polymer composite
PublicationThis paper presents an experimental and numerical investigation of the performance of a sorbent polymer composite (SPC) material used for removing mercury from the flue gases in a full-scale industrial installation. The investigated material is an attractive alternative to activated carbon, which is commonly used for this purpose. While the application of the SPC is characterized by high capital expenditures, this technology offers...
-
Load introduction to composite columns revisited—Significance of force allocation and shear connection stiffness
PublicationThe AISC 360-16 Specification recommends that the design shear force between parts of a composite column in the load introduction area shall be calculated based on the force allocation at ultimate limit state. Applicability of this straightforward method to the load levels that usually arise in slender composite columns is questionable, as this capacity-based force allocation is only true when the axial force is equal to the plastic...
-
Facilitated water transport in composite reduced graphene oxide pervaporation membranes for ethanol upgrading
PublicationHigh purity ethanol is one of the most sought-after renewable energy sources. However, standard production methods yield ethanol of insufficient quality. Membrane processes such as pervaporation are recognized as a viable method for upgrading ethanol. Their performance and selectivity depend solely on membrane employed. Hydrophilic polyvinyl alcohol (PVA) membranes are used industrially for this purpose, but there is a trade-off...
-
Tailoring of Magnetic Properties of NiO/Ni Composite Particles Fabricated by Pulsed Laser Irradiation
Publication -
Electrodes Based on a Titanium Dioxide Nanotube–Spherical Silver Nanoparticle Composite for Sensing of Proteins
Publication -
Modelling of wave propagation in composite plates using the time domain spectral element method
PublicationW pracy przedstawiono wyniki obliczeń propagacji fali sprężystej w płycie kompozytowej modelowanej z wykorzystaniem czasowego sformułowania metody elementów spektralnych
-
Microwave-assisted preparation of Li3V2(PO4)3/C composite with high-rate capacity
Publication -
Design and fabrication of flexible poly(vinyl chloride) dielectric composite reinforced with ZnO microvaristors
Publication -
Chapter 13 : The influence of dispersion phase on composite coating properties after cold working
PublicationW pracy określono wpływ fazy dyspersyjnej Al2O3 na wybrane potencjalne właściwości powłok kompozytowych o osnowie niklowej. Powłoki Ni-Al-Al2O3 zostały nałożone na próbki stalowe przy użyciu technologii poddźwiękowego płomieniowego natryskiwania cieplnego. Następnie poddane zostały obróbce plastycznej na zimno i na gorąco poprzez walcowanie, a także prasowania na zimno na prasie hydraulicznej. Obróbka plastyczna jest metodą alternatywną...
-
The effect of the ceramic dispersion on the nickel matrix composite coating properties after plastic working
PublicationW pracy określono wpływ fazy dyspersyjnej Al2O3 na wybrane potencjalne właściwości powłok kompozytowych o osnowie niklowej. Powłoki Ni-Al-Al2O3 zostały nałożone na próbki stalowe przy użyciu technologii poddźwiękowego płomieniowego natryskiwania cieplnego. Następnie poddane zostały obróbce plastycznej na zimno i na gorąco poprzez walcowanie, a także prasowania na zimno na prasie hydraulicznej. Obróbka plastyczna jest metodą alternatywną...
-
PANI/NaTaO3 composite photocatalyst for enhanced hydrogen generation under UV light irradiation
Publication -
Porous silica matrix as an efficient strategy to boosted photocatalytic performance of titania/carbon composite
Publication -
Graphene oxide, reduced graphene oxide and composite thin films NO2 sensing properties
PublicationA graphene oxide (GO), reduced graphene oxide (RGO) and poly(3,4-ethylenedioxytiophene)-reduced graphene oxide (PEDOT-RGO composite) gas sensors were successfully fabricated using an electrodeposition method. The electrodeposition was carried out in aqueous GO dispersions. To obtain RGO and PEDOT-RGO, the electrochemical reduction of GO and PEDOT-GO was carried out in 0.1 M KCl at a constant potential of −0.85 V. The GO, RGO and PEDOT-RGO...
-
Fabrication of Composite Polyurethane/Hydroxyapatite Scaffolds Using Solvent-Casting Salt Leaching Technique
PublicationScaffolds are porous three-dimensional structures which are used to fill bone losses and make them possible to cells to grow. Many different structural and biological properties are required from them: porosity, mechanical strength and biocompability. The present research is aimed at development of composite polyurethane/hydroxyapatite scaffolds by using the solvent-casting salt leaching method. The SEM examinations were applied...
-
Distortional buckling of composite thin-walled columns of a box-type cross section with diaphragms
PublicationDistortional buckling of axially compressed columns of box-like composite cross sections with andwithout internal diaphragms is investigated in the framework of one-dimensional theory. The channel membersare composed of unidirectional fibre-reinforced laminate. Two approaches to the member orthotropic materialare applied: homogenization based on the theory of mixture and periodicity cells, and homogenization basedon the Voigt–Reuss...
-
Experimental investigation of Steel–Concrete–Polymer composite barrier for the ship internal tank construction
PublicationTransportation of dangerous cargo by ships demands ensuring an appropriate protection level in case of an accident. Two of the most dangerous accident types resulting in an oil spill are grounding and ship to ship collision. The article presents results of research on a new composite construction for a ship hull that increases structural safety during collision. The concept of semi-elastic Steel–Concrete–Polymer structure is presented....
-
Stainless steel/yttria stabilized zirconia composite supported solid oxide fuel cell
PublicationW tym artykule opisano wytworzenie i przebadanie kompozytowych elementów nośnych tlenkowych ogniw paliwowych. Podłoża nośne zostały wytworzone ze stali nierdzewnej i tlenkiem itru stabilizowanego tlenku cyrkonu (YSZ), których proszki zmieszano w różnych proporcjach objętościowych. Zachowanie podłoży podczas spiekania (skurcz liniowy, porowatość) oraz wysokotemperaturowe właściwości (odporność na utlenianie, przewodność elektryczna)...
-
Deformation Analysis of a Composite Bridge during Proof Loading Using Point Cloud Processing
PublicationRemote sensing in structural diagnostics has recently been gaining attention. These techniques allow the creation of three-dimensional projections of the measured objects, and are relatively easy to use. One of the most popular branches of remote sensing is terrestrial laser scanning. Laser scanners are fast and efficient, gathering up to one million points per second. However, the weakness of terrestrial laser scanning is the...
-
Non-enzymatic flexible glucose sensing platform based on nanostructured TiO2–Au composite
PublicationAll over the world the number of people suffering from diabetes and related complications is drastically growing. Therefore, the need for accurate, reliable and stable sensor for monitoring of glucose in human body fluids is becoming highly desirable. In this work we show that material composed of gold layers deposited onto TiO2 nanotubes (NTs) formed onto the flexible Ti foil exhibits great response toward glucose oxidation and...
-
Graphene oxide, reduced graphene oxide and composite thin films NO2 sensing properties
PublicationA graphene oxide (GO), reduced graphene oxide (RGO) and poly(3,4-ethylenedioxytiophene)- reduced graphene oxide (PEDOT-RGO composite) gas sensors were successfully fabricated using an electrodeposition method. The electrodeposition was carried out in aqueous GO dispersions. In order to obtain RGO and PEDOT-RGO, the electrochemical reduction of GO and PEDOT-GO was carried out in 0.1 M KCl at constant potential of −0.85 V. The GO, RGO...
-
Performance of a single layer fuel cell based on a mixed proton-electron conducting composite
PublicationMany of the challenges in solid oxide fuel cell technology stem from chemical and mechanical incompatibilities between the anode, cathode and electrolyte materials. Numerous attempts have been made to identify compatible materials. Here, these challenges are circumvented by the introduction of a working single layer fuel cell, fabricated from a composite of proton conducting BaCe0.6Zr0.2Y0.2O3-δ and a mixture of semiconducting...
-
S-scheme heterojunction Bi2O3-ZnO/Bentonite clay composite with enhanced photocatalytic performance
PublicationThe industrial waste water is always a bottleneck problem in the modern civilization of the present era. In a quest to develop effective methods for the elimination of lethal pollutants from the waste water and water remediation, this work is focused on the development of a rapid and proficient approach for preparing supported binary metal oxide catalyst for photocatalytic advance oxidation process used in waste water treatment...
-
Polyurethane Composite Scaffolds Modified with the Mixture of Gelatin and Hydroxyapatite Characterized by Improved Calcium Deposition
PublicationThe skeleton is a crucial element of the motion system in the human body, whose main function is to support and protect the soft tissues. Furthermore, the elements of the skeleton act as a storage place for minerals and participate in the production of red blood cells. The bone tissue includes the craniomaxillofacial bones, ribs, and spine. There are abundant reports in the literature indicating that the amount of treatments related...
-
Edgewise Compressive Behavior of Composite Structural Insulated Panels with Magnesium Oxide Board Facings
PublicationEdgewise compression response of a composite structural insulated panel (CSIP) with magnesium oxide board facings was investigated. The discussed CSIP is a novel multifunctional sandwich panel introduced to the housing industry as a part of the wall, floor, and roof assemblies. The study aims to propose a computational tool for reliable prediction of failure modes of CSIPs subjected to concentric and eccentric axial loads. An advanced...
-
Effect of chemical composition on corrosion and wear behaviour of the composite Ni-Fe-Al2O3 coatings.
PublicationPrzedstawiono wyniki badań powłoki kompozytowej otrzymanej przez osadzanie katodowe galwaniczne w roztworze zawierającym sole niklu, żelaza oraz cząstki ceramiki Al2O3 o różnej wielkości i stężeniu. Wykazano, że charakterystyka ceramiki posiada wpływ na szybkość korozji i zużycia ściernego. W szczególności, zawartość ceramiki wpływa dodatnio na odporność na zużycie ścierne, ale nieco obniża odporność na zużycie korozyjne.
-
FRP-based reinforcement coatings of steel with application prospects in ships and offshore structures: a review
PublicationLatest research on novel FRP-based anti-corrosion structural coatings (for enhancing structural capacity and strengthening the coating layer) is discussed with application prospects for ships and offshore structures. In the marine environment, structures constantly face corrosion and fatigue cracks. Combining this with high operational and wave loads, it might cause a structural collapse. Recently, polymer composites have been...
-
A Proposed Soft Computing Model for Ultimate Strength Estimation of FRP-Confined Concrete Cylinders
PublicationIn this paper, the feed-forward backpropagation neural network (FFBPNN) is used to propose a new formulation for predicting the compressive strength of fiber-reinforced polymer (FRP)-confined concrete cylinders. A set of experimental data has been considered in the analysis. The data include information about the dimensions of the concrete cylinders (diameter, length) and the total thickness of FRP layers, unconfined ultimate concrete...
-
Fabrication, microstructure and properties of Al-Si -Fe-Cu in situ composites.
PublicationW poszukiwaniu tanich kompozytów na bazie stopów Al powstała koncepcja otrzymywania kompozytów in situ o osnowie stopu Al-Si w reakcji ciekłego stopu Al-Si (Al-Si11, Al-Si25) z proszkiem Fe. Powstałe wydzielenia np. iglastego AlFe4Si w stopie AlSi25 o niezbyt wysokiej twardości (rys.2) stanowią skuteczne wzmocnienie stopu pod względem twardości, sztywności i wytrzymałości na ściskanie jak też obniżonej ścieralności. Jednak znaczny...
-
Silica xerogel–hydrogen peroxide composites: Their morphology, stability, and antimicrobial activity
Publication -
Evaluation and rationale of the performance of several elastomeric composites incorporating devulcanized EPDM
Publicationthylene Propylene Diene rubber (EPDM), is present in many applications. However, its crosslinked structure makes difficult its recycling. The use of devulcanized EPDM, (dEPDM) as a component of elastomeric composites, is a real possibility to reuse EPDM scraps. In this study, three matrices (natural rubber (NR), styrene butadiene rubber (SBR) and EPDM rubber) have been tested including devulcanized EPDM as a recycled component....
-
Polyurethane-wood composites (PU-WC) as a method of wood waste management
PublicationIn recent years, due to the progressive environmental degradation and increase of environmental awareness, the sustainability of production systems in wood processing, the wood industry, and wood waste management is a crucial issue for European industry and society. Consequently, the problem of generating wood-like waste and the associated risks has become an increasingly noticeable challenge for science. Although various methods...
-
Infiltration - an alternative method to prepare composites for Solid Oxide Fuel Cells
PublicationPrzedstawiono różne techniki nasączania pozwalające na uzyskanie materiałów o mieszanym przewodnictwie jonowo-elektronowym do zastosowań w tlenkowych ogniwach paliwowych
-
Design of dimensionally stable composites using efficient global optimization method
Publication -
Modification of Ground Tire Rubber—Promising Approach for Development of Green Composites
Publication -
Self-lubricating epoxide composites Kompozyty epoksydowe o właściwościach samosmarujących
Publication -
Environmental stress cracking in e-glass and aramid/glass epoxy composites
PublicationKompozyty epoksydowe wzmocnione włóknami szklanymi są dość odporne na wpływy środowiskowe w stanie nieobciążonym, jednak po przyłożeniu obciążeń łatwo pękają w środowisku wody i rozcieńczonych kwasów. Charakterystyki propagacji pęknięć środowiskowych w laminatach szklano/epoksydowych były przedmiotem szeregu prac, jednak brak jest danych na temat zachowania laminatów o wzmocnieniu hybrydowym aramidowo-szklanym stosowanych w budowie...
-
3D composites based on the blends of chitosan and collagen with the addition of hyaluronic acid
Publication -
Quasi-Static and Dynamic Testing of Carbon Fiber Reinforced Magnesium Composites
Publication -
FTIR Study and Mechanical Properties of Cellulose Fiber-Reinforced Thermoplastic Composites
Publication -
Determination of percolation threshold in cement composites with expanded graphite by impedance spectroscopy
Publication -
Mechanical properties cement based composites modified with nano-Fe3O4/SiO2
Publication -
PROPERTIES OF FIBER REINFORCED CEMENT COMPOSITES WITH CENOSPHERES FROM COAL ASH
Publication -
Effect of carbon nanotube modification on poly (butylene terephthalate)-based composites
Publication -
Current-Voltage Characteristics of the Composites Based on Epoxy Resin and Carbon Nanotubes
Publication -
Environmental aspects of coastal earth structures made of soil-ash composites
PublicationThis paper presents an innovative technology of building the coastal dams with the use of soil-ash composites. A natural- scale test stand and results of the performed environmental tests are presented ; they have been compared with standards for purity of soils and waters. Also, an analysis of the obtained results and discussion of trends and anomalies in the observations, are given.
-
Direct shear stress vs strain relation for fiber reinforced composites
PublicationThe majority of fiber reinforced composites exhibit strong non-linear behavior in in-plane shear state. The effect is attributed to the micro-cracks appearing in the matrix and can be modeled on the micro and macro level. In this work the author proposes constitutive laws describing the non-linear in-plane shear response, which can be alternative for the relations commonly considered in the literature. The proposed equations are...
-
TESTING CONTRACTION AND THERMAL EXPANSION COEFFICIENT OF CONSTRUCTION AND MOULDING POLYMER COMPOSITES
PublicationThe paper presents results of systematic tests of contraction and thermal expansion coefficients of materials based on polymer composites. The information on the above material properties is essential both at the design stage and during the use of finished products. Components for the samples were selected in such a way as to represent typical materials used for production of construction and moulding elements. The performed tests...