Filtry
wszystkich: 28497
wybranych: 7308
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: STANDARD STEP METHOD
-
Spectral Finite Element Method in Condition Monitoring and Damage Detection
PublikacjaIt is well known that the dynamic behaviour of engineering structures may carry very important and crucial information that can be further used for the assessment of their condition as well as detection of any damage induced. The current interest in monitoring techniques based on the propagation of guided elastic waves requires that numerical techniques used for modelling the phenomena associated must shift into the realm of high...
-
Method of sacrificial anode transistor-driving in cathodic protection system
PublikacjaA magnesium anode driving system has been proposed. A PNP driving transistor has been used. Electrochemical testing in 3%NaCl, results and comparison of the driving system and classic direct anode to cathode connection are presented. The driving system reduced the protection current and stabilized the working conditions of the anode. Higher anode efficiency was achieved. Overprotection and hydrogen embrittlement threats were prevented...
-
The Urban Mentoring as a New Method of Participatory Urban Planning in Poland
PublikacjaTwenty-five years after the return of democracy and the beginning of basing the country's economy on neoliberal developmental paradigm, Poland adopted the regulations regarding management of urban policy, which had been wait for over a decade (accession to the EU). The National Urban Policy as well as the Act on revitalization have defined, in a modern manner, the field of cooperation between the local government, the administration...
-
Deformation of the Structural Details of the Components Created by the Rapid Prototyping Method
PublikacjaThe paper present the results of preliminary research and describes the deformation of construction details within the process of producing small element employing a stereography system. The article discuses a scheme for changes in data conversion. Variation in construction details have been described on the basis of analysing photographs.
-
Optical method for verification of homogeneity of phantoms for calibration of magnetic resonance
PublikacjaThe primary purpose of this study was to develop a laboratory photonic set-up for characterisation of homogeneity of gel phantoms for calibration of magnetic resonance. In this system, optical coherence tomography allows the detection of micro- and macroscopic heterogeneities of a structure. The set-up was used to perform measurements of agar and agar-carrageenan gels, which are the basis for more complex phantoms for magnetic...
-
Application of method of differential magnetometric system for detection of sunken objects
PublikacjaThis paper presents a magnetometric system with scalar sensors mounted on two independent platforms, which is used to detect sunken shipwrecks. Increasing the distance between the sensors allows for more precise measurement of the difference in the magnetic induction module than in the case of sensors mounted e.g. on the aeroplane’s wings. This type of system makes it possible to enlarge detection range of the sunken wrecks.
-
The original method of cutting power forecasting while wood sawing
PublikacjaEfekty energetyczne procesu przecinania drewna piłami (siły skrawania i moc skrawania) przy klasycznym podejściu do zagadnienia są określane na podstawie wartości właściwego powierzchniowego oporu skrawania. Z drugiej strony siły skrawania można rozważać z punktu widzenia współczesnej mechaniki pękania. Prognozowanie wartości kąta ścinania z zastosowaniem modeli uwzględniających wiązkość materiału obrabianego, ścinanie w płaszczyźnie...
-
The Method of Reduction of Aerodynamic Forces Generated in Turbine Blade Seals
PublikacjaOpisano metodę zmniejszania sił wymuszających drgania aerodynamiczne poprzez zastosowanie nowego uszczelnienia nadbandażowego typu komorowego. Efektywność stosowania uszczelnienia komorowego potwierdzono obliczeniami numerycznymi i badaniami eksperymentalnymi.
-
Monotone iterative method for first-order differential equations at resonance
PublikacjaThis paper concerns the application of the monotone iterative technique for first-order differential equations involving Stieltjes integrals conditions. We discuss such problems at resonance when the measure in the Stieltjes integral is positive and also when this measure changes the sign. Sufficient conditions which guarantee the existence of extremal, unique and quasi-solutions are given. Three examples illustrate the results.
-
Filtering of interference signals of grounding resistance measurement with subharmonic method
PublikacjaOmówiono metodę filtracji zakłóceń o częstotliwości sieciowej wraz z wyższymi harmonicznymi poprzez zastosowanie metody szczególnego próbkowania z podharmonicznym sygnałem pomiarowym.
-
Extensions of Quasilinearization Method for Differential Equations with Integral Boundary Conditions
PublikacjaPraca dotyczy równań różniczkowych z warunkami brzegowymi typu całkowego. Podano warunki dostateczne na istnienie jedynego rozwiązania takiego zagadnienia i pokazano, że odpowiednio konstruowane ciągi monotoniczne są zbieżne do tego rozwiązania i jest to zbieżność kwadratowa. Te monotoniczne ciągi są przybliżonymi rozwiązaniami problemu wyjściowego i obustronnie szacują szukane rozwiązanie.
-
A risk-based method for ship safety assessment at the preliminary designstage
PublikacjaPraca zawiera wyniki badań dotyczących opracowania metody do analizy bezpieczeństwa statku w warunkach krytycznych. Metoda oparta jest na podejściu systemowym do oceny bezpieczeństwa, formalnej ocenie bezpieczeństwa FSA i hydromechanice okrętu. Podano przykłady oceny ryzyka utraty statku w warunkach krytycznych.
-
Inverse method for 3D shaped centrifugal compressor (rotor and diffuser)
PublikacjaW artykule przedstawiono sposób wyznaczania kształtu wirnika i dyfuzora sprężarki promieniowej. Podano układ równań oraz warunki zamknięcia układu. Przykładowe rozwiązanie wskazuje na silny wpływ warunków na wlocie na kształt dyfuzora.
-
Application of Adomian decomposition method in analysis of displacements ofrandom subsoil
PublikacjaW pracy przedstawiono metodę dekompozycji Adomiana oraz jej zastosowanie do rozwiązania zagadnienia losowego ośrodka gruntowego. Rozpatrzono ważką warstwę gruntu, posadowioną na nieodkształcalnym podłożu, poddaną działaniu równomiernie rozłożonego pionowego obciążenia zewnętrznego. Przyjęto, że ośrodek jest sprężysty, a jego parametry są funkcjami losowymi. Uzyskano przybliżone rozwiązanie analityczne wraz z oceną zakresu jego...
-
Efficient implementation of the Cauchy method for automated CAD-model construction.
PublikacjaW artykule przedstawiona została efektywna metoda konstrukcji wieloparametrycznych modeli układów mikrofalowych na podstawie wyników symulacji pełnofalowej. Algorytm wykorzystuje metodę najmniejszych kwadratów (TLS) do rozwiązania problemu interpolacyjnego i automatycznie dobiera rząd modelu.Przydatność i dokładność metody jest pokazana na przykładzie projektowania filtru z wykorzystaniem modeli trzech i pięciu zmiennych.
-
A direct method for risk assessment when ship is in critical conditions
PublikacjaPrzedstawiono metodę oceny bezpieczeństwa statku w warunkach krytycznych. Zdefiniowano warunki krytyczne. Podano praktyczne sposoby oceny ryzyka przetrwania statku w warunkach krytycznych. Opisano bezpośrednią metodę oceny ryzyka w warunkach krytycznych. Podano przykłady oceny ryzyka.
-
A new method of current limitation. Nowa metoda ograniczania prądu.
PublikacjaZaprezentowano nowa ideę hybrydowego, bezstykowego ogranicznika prądów zwarciowych oraz możliwości jego aplikacji. W ograniczniku tym zastąpiono łącznik zestykowy bezpiecznikiem o ultra krótkim topiku, dzięki czemu uniknięto niedogodności związanych z napędem występujących w klasycznych łącznikach hybrydowych. Rolą bezpiecznika w tym nowym zestawie jest wyłącznie zadziałanie w warunkach zwarciowych, a po przejęciu prądu...
-
Water hammer analysis in pipe networks by the method of characteristics (MOC).
PublikacjaZastosowano w pracy metodę charakterystyk do analizy zjawiska uderzenia hydraulicznego w sieci wodociągowej pierścieniowej.
-
The dynamic analysisi of cracked Thimoshenko beam by the spectral element method.
PublikacjaW pracy przedstawiono model belli Timoshenko z pęknięciem poprzecznym oparty o metodę elementów spektralnych. Przedstawiono wyniki propagacji fali sprężystej i jej interakcję z pęknięciem.
-
Inconsistent i contradictory judgements in pairwise comparison method in AHP.
PublikacjaCelem artykułu jest pokazanie zależności pomiędzy niezgodnymi i sprzecznymi macierzami danych, otrzymywanymi w wyniku porównań parami niewielkiej, skończonej libzy wariantów decyzyjnych. W szczególności pokazuje się macierze, które mimo prawidłowego wyniku testu zgodności posiadają oceny sprzeczne. Przedstawia się algorytm sprawdzający zgodność ocen.
-
adaptive finite-element multigrid method in 3d magnetostatic analysis.
PublikacjaPrzedstawiono procedurę analizy magnetostatycznej obwodów mikrofalowych zawierających przewodniki o dowolnym kształcie. Zakłada się pobudzenie pola magnetostatycznego zadane w postaci wartości całkowitego prądu płynącego w przewodniku sygnałowym. Warunki brzegowe w strukturze od dowolnym kształcie, bez płaszczyzn symetrii wprowadza się za pomocą powierzchni rozdzielających. Takie sformułowanie problemu prowadzi jednak do szeregu...
-
Eigenchannel method for nonrelativistic scattering from zero-range potentials.
PublikacjaPrzedstawiono sformułowanie metody kanałów własnych dla rozpraszania cząstek Schrodingera na układzie potencjałów zerowego promienia. Jako przykład, rozważono rozpraszanie fali płaskiej na czterech identycznych potencjałach, tworzących strukturę o symetrii tetraedrycznej.
-
The experimental method of reducing magnetic field intensity in industrial buidings
PublikacjaPrzedstawiono metodę obniżenia poziomu intensywności zakłóceń w budynkach pracującego zakładu przemysłowego. Potrzeba wykonania badań pola elektromagnetycznego wynikała m.in. z zaobserwowanej wśród pracowników jednego z działów zakładu większej podatności na zachorowania. Na drodze pomiarów zlokalizowano źródła silnego pola magnetycznego w zakresie małych częstotliwości. Na podstawie analizy wyników pomiarowych sformułowano wnioski...
-
A performance-oriented risk-based method for safety assessment of ships
PublikacjaW pracy przedstawiono wybrane informacje na temat metody oceny bezpieczeństwa statków w warunkach krytycznych. Metoda łączy podejście oparte na ocenie osiągów statku z podejściem opartym o ocenę ryzyka wypadku. Analiza ryzyka w metodzie oparta jest na zastosowaniu elementów Formalnej Oceny Bezpieczeństwa FSA. Analiza ryzyka w metodzie dotyczy: identyfikacji zagrożeń, oceny zagrożeń, identyfikacji scenariuszy wypadku, oceny ryzyka,...
-
A Surrogate-Assisted Measurement Correction Method for Accurate and Low-Cost Monitoring of Particulate Matter Pollutants
PublikacjaAir pollution involves multiple health and economic challenges. Its accurate and low-cost monitoring is important for developing services dedicated to reduce the exposure of living beings to the pollution. Particulate matter (PM) measurement sensors belong to the key components that support operation of these systems. In this work, a modular, mobile Internet of Things sensor for PM measurements has been proposed. Due to a limited...
-
The dependence of linear viscoelasticity limits of cold-recycled mixtures on time of curing and compaction method
PublikacjaCold-recycled mixtures are currently among the most widely used and investigated methods that enable recycling of old pavement structures in an environmentally friendly manner. Upon milling, the old pavement structure – whose gradation can be improved with addition of virgin aggregate – is mixed and compacted at ambient temperature. The main binding agents are bituminous emulsion and cement. Due to their dual binding behaviour,...
-
A facile method for Tauc exponent and corresponding electronic transitions determination in semiconductors directly from UV–Vis spectroscopy data
PublikacjaIn this work, a facile method allowing for estimation of the exponent in the Tauc equation directly from the UV–vis spectra is presented. It is based on the Taylor expansion of the logarithmic version of the Tauc equation. The Tauc exponent is calculated from the tangent slope of the absorption data. Knowledge of this coefficient provides information about the optical transition types and is used as an input for the calculations...
-
Method of earth fault loop impedance measurement without nuisance tripping of RCDs in 3-phase low-voltage circuits
PublikacjaVerification of electrical safety in low-voltage power systems includes the measurement of earth fault loop impedance. This measurement is performed to verify the effectiveness of protection against indirect contact. The widespread classic methods and meters use a relatively high value of the measuring current (5–20) A, so that they are a source of nuisance tripping of residual current devices (RCDs). The meters dedicated to circuits...
-
Precise Point Positioning Method Based on Wide-lane and Narrow-lane Phase Observations and Between Satellites Single Differencing
PublikacjaThe issue of using PPP method in position determination was formed in 1997. In most developed methods, ionospheric-free linear combination is used in order to eliminate the impact of the ionospheric delay. However, this approach does not provide the directly determination of the total value of the ambiguities, and the ambiguities for the individual signals. Therefore, in many publications methods of avoiding these deficiencies...
-
Optimization of capillary isotachophoretic method for determination of major macroelements in blue honeysuckle berries (Lonicera caerulea L.) and related products
PublikacjaA reliable and repeatable isotachophoretic method for the simultaneous determination of K+, Na+, Ca2+, Mg2+ and ammonium in berries of different blue honeysuckle cultivars was developed. The usefulness of the complex-forming equilibria in determining the cations mentioned above was studied. The addition of 7.5 mM 18-crown-6 and 2 mM α-hydroxyisobutyric acid to sulfuric acid enhanced the separation capacity of the leading electrolyte....
-
A study on microcrack monitoring in concrete: discrete element method simulations of acoustic emission for non-destructive diagnostics
PublikacjaThe research is focused on the monitoring of fracture evolution in concrete beams under three-point bending using the acoustic emission technique and the discrete element method. The main objective of the study was to numerically and experimentally investigate the mechanism behind the generation of elastic waves during acoustic emission events and their interaction with micro- and macro-cracking in concrete beams under monotonic...
-
New procedure of silica gel surface modification-preparation of gaseous standard mixtures of methyl chloride using the technique of thermal decomposition of the surface compound for calibration of a TD-GC-FID system.
PublikacjaPrzedstawiono nową procedurę modyfikacji powierzchni żelu krzemionkowego w celu wytworzenia związku powierzchniowego będącego źródłem chlorku metylu. Minimalna temperatura rozkładu (150 st. C) zapewnia trwałość chemicznie modyfikowanego złoża w temp. pokojowej. Badania prowadzono w temperaturze optymalnej (280 st.C). Stwierdzono, że powierzchnia żelu jest obsadzona jednorodnie przez związek powierzchniowy i gazowa mieszanina wzorcowa...
-
Open-Phase Fault Detection Method for Sensorless Five-Phase Induction Motor Drives with an Inverter Output Filter
PublikacjaThe paper presents the sensorless five-phase induction motor drive implementation with an inverter output filter with third harmonic injection. For the sensorless operation, the required observers are presented for the first and third harmonics with consideration of the inverter output filter. Moreover, the interaction of the observers and the control system is capable to handle a deactivation of one or two phases, which improves...
-
Pączkowanie - metoda rozwoju interoperacyjnych komponentów dla systemów rozproszonych = Budding – the software development method of interoperable components for distributed systems
PublikacjaPrzedstawiono 2 współczesne metody wytwarzania oprogramowania: iteracyjno-przyrostową oraz techniki zwinne, ich zalety i wady w kontekście budowy interoperacyjnych platform i środowisk rozproszonych. Zaprezentowano metodę rozwoju oprogramowania przez pączkowanie, jej założenia, zalety i wady. Przedstawiono technologie, na bazie których działa metodologia wytwarzania oprogramowania przez pączkowanie: Software Product Line, Enterprise...
-
Assessing groundwater vulnerability to pollution in the Puck region (denudation moraine upland) using vertical seepage method
PublikacjaDegradation of groundwater quality can cause a serious water supply and environmental problems. The identify of potential groundwater pollution can be determined by assessment of groundwater vulnerability method. The assessment of groundwater vulnerability to pollution was based on estimation of migration time of potential conservative contamination through the vadose zone. Area of investigation is a type of denudation moraine...
-
Modification of gradient HPLC method for determination of small molecules' affinity to human serum albumin under column safety conditions: Robustness and chemometrics study
PublikacjaIn the early stages of drug discovery, beyond the biological activity screening, determining the physicochemical properties that affect the distribution of molecules in the human body is an essential step. Plasma protein binding (PPB) is one of the most important investigated endpoints. Nevertheless, the methodology for measuring %PPB is significantly less popular and standardized than other physicochemical properties, like lipophilicity....
-
Synthesis and structural properties of (Y, Sr)(Ti, Fe, Nb)O3−δ perovskite nanoparticles fabricated by modified polymer precursor method
PublikacjaThe yttrium, iron and niobium doped-SrTiO3 powders have been successfully fabricated by a modified low–temperature synthesis method from a polymer complex. The usage of strontium hydroxide precursor instead of conventional strontium nitrate or strontium carbonate provides to the possibility of significant decrease of annealing temperature. It allows to prepare a material with sphere-shape grains of nanometric size (15–70 nm). The...
-
Practical aspects of testing superconducting electromagnets by the capacitor discharge method taking into account the non-linearity of circuit parameters
PublikacjaThe article presents selected issues related to the development and testing of the diagnostics systems dedicated for superconducting electromagnets. The systems were constructed to assess the production quality of superconducting electromagnets of the SIS100 synchrotron, a new accelerator being built as part of the Facility of Antiproton and Ion Research (FAIR). One of the systems is used for automatic checking of electrical connection...
-
PRELIMINARY FIELD TESTS AND LONG-TERM MONITORING AS A METHOD OF DESIGN RISK MITIGATION: A CASE STUDY OF GDAŃSK DEEPWATER CONTAINER TERMINAL
PublikacjaAppropriate risk assessment plays a fundamental role in the design. . The authors propose a possible method of design risk mitigation, which follows recommendations included in Eurocode 7. The so-called “Observational Method” (OM) can produce savings in costs and programmes on engineering projects without compromising safety. The case study presented is a complex design solution that deals with the heavy foundations of a gantry...
-
Validation of Hydraulic Mechanism during Blowout Trauma of Human Orbit Depending on the Method of Load Application
PublikacjaThe more we know about mechanisms of the human orbital blowout type of trauma, the better we will be able to prevent them in the future. As long as the buckling mechanism’s veracity is not in doubt, the hydraulic mechanism is not based on equally strong premises. To investigate the correctness of the hydraulic mechanism’s theory, two different methods of implementation of the hydraulic load to the finite element method (FEM) model...
-
Development and validation of a GC–MS/MS method for the determination of 11 amphetamines and 34 synthetic cathinones in whole blood
PublikacjaPurpose Psychoactive compounds that contain a phenylethylamine structure (such as amphetamine-type stimulants and synthetic cathinones) are one of the major classes of stimulants on the recreational drug market. Approximately 670 new psychoactive substances (NPS) are monitored only in Europe; however, new psychoactive compounds are being developed for illicit trade each year. In this context, the development of new analytical procedures...
-
A pilot study to assess an in-process inspection method for small diameter holes produced by Direct Metal Laser Sintering
PublikacjaPurpose The purpose of this research is to evaluate the geometric quality of small diameter holes in parts printed by DMLS technology. An in-process optical inspection method is proposed and assessed during a pilot study. The influence of the theoretical hole diameter assumed in a CAD system and the sample thickness (hole length) on the hole clearance was analysed. Design/methodology/approach The samples made of two different...
-
Prediction of metal deformation due to line heating; an alternative method of mechanical bending, based on artificial neural network approach
PublikacjaLine heating is one of the alternative methods of forming metals and this kind of forming uses the heating torch as a source of heat input. During the process, many parameters are considered like the size of the substrate, thickness, cooling method, source power intensity, the travel speed of the power source, the sequence of heating, and so on. It is important to analyze the factors affecting the...
-
Enhanced Spectroscopic Insight into Acceptor-Modified Barium Strontium Titanate Thin Films Deposited via the Sol–Gel Method
PublikacjaIn the present paper, composite thin films of barium strontium titanate (BaxSr1−xTiO3) with an acceptor modifier (magnesium oxide—MgO) were deposited on metal substrates (stainless steel type) using the sol–gel method. The composite thin films feature BaxSr1−xTiO3 ferroelectric solid solution as the matrix and MgO linear dielectric as the reinforcement, with MgO concentrations ranging from 1 to 5 mol%. Following thermal treatment...
-
Cathodically activated Au/TiO2 nanocomposite synthesized by a new facile solvothermal method: An efficient electrocatalyst with Pt-like activity for hydrogen generation
PublikacjaWe report here a facile, template-free and one-step solvothermal approach for the synthesis of high-temperature stable gold/titania nanocomposite (NCs), providing a new, simple, quick and inexpensive wet-chemical route. Our approach is based on the assembly of gold salt and titanium butoxide in dimethyl sulfoxide (DMSO). Also, we present here, for the first time, a cathodically activated Au/TiO2 catalyst with Pt/C activity for...
-
Full scale measurements of pressure field induced on the quay wall by bow thrusters – indirect method for seabed velocities monitoring
PublikacjaThe paper presents the results of full-scale experimental investigation of loads generated on the quay wall by bow thrusters during unberthing of a self-manoeuvring vessel. The presented research allowed for the comparison of the measurements results with generally accepted empirical prediction methods and confirmed the utility of the developed measuring setup for the on-line monitoring of jet induced loads. The conclusions from the...
-
Investigations of size effect in concrete at aggregate level - experiments and calculations results using discrete element method
PublikacjaSize effect is a fundamental phenomenon in concrete. It is characterised by decreasing strength and increasing brittleness of concrete with increasing size. The thesis includes experimental and theoretical elements. The main goal of the thesis were investigations of a size effect at the aggregate level by taking fracture into account with the discrete element method (DEM) for various failure modes. Comprehensive experiments on...
-
Investigation of poly(3,4-ethylenedioxythiophene) deposition method influence on properties of ion-selective electrodes based on bis(benzo-15-crown-5) derivatives
PublikacjaGlassy carbon electrodes modified by conductive polymers and membrane with derivatives of bis(benzo-15-crown-5) were tested as solid contact ion selective electrodes for K+ ions concentration determination. PEDOT with PSS, Cl- and ClO4- counter ions was electrochemically deposited onto glassy carbon substrates using four different electrochemical approaches (potentiostatic, galvanostatic, potentiodynamic and potentiostatic pulses)....
-
Preconditioners with Low Memory Requirements for Higher-Order Finite-Element Method Applied to Solving Maxwell’s Equations on Multicore CPUs and GPUs
PublikacjaThis paper discusses two fast implementations of the conjugate gradient iterative method using a hierarchical multilevel preconditioner to solve the complex-valued, sparse systems obtained using the higher order finite-element method applied to the solution of the time-harmonic Maxwell equations. In the first implementation, denoted PCG-V, a classical V-cycle is applied and the system of equations on the lowest level is solved...
-
Adaptive dynamic control allocation for over-actuated dynamic positioning system based on backstepping method in case of thruster faults
PublikacjaThe objective of the research considered in this paper is dynamic positioning of a nonlinear over-actuated marine vessel in the presence of limited information about thruster forces. First, the adaptive backstepping method is used to estimate the input matrix which will compensate partial loss of actuator effectiveness in the presence of actuator dynamics. Then, the adaptive commanded virtual forces and moment are allocated into...