Filtry
wszystkich: 4518
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: unsteady surface flow
-
Effect of Laminar Pulsatile Fluid Flow on Separation of Volatile Organic Compounds from Aqueous Solution by a Hollow Fiber Membrane-Based Process
PublikacjaIn this study, a laminar pulsatile fluid flow was used for the separation of benzene, toluene, ethylbenzene, and xylene isomers (BTEX) from aqueous solutions. Polyether sulfone hollow fiber membrane has been applied to this process. The effects of BTEX concentration, and feed and extraction flow rates were examined. It was found that the application of the pulsatile fluid flow with...
-
The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
PublikacjaThe paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate...
-
Bio and slide biobearings, their lubrication by non-newtonian fluids and application in non-conventional systems. Vol. 2, The theory of human joint unsteady lubrication.
PublikacjaW monografii przedstawiono zasady niestacjonarnego smarowania stawów człowieka o odkształcalnych chrząstkach i powierzchniach kostnych w polach indukcji magnetycznej. W opisie stochastycznym uwzględnione zostały nienewtonowskie, lepkosprężyste właściwości cieczy synowialnych jako czynnika smarującego. Monografia prezentuje rozkłady wartości ciśnienia i nośności stawów człowieka w warunkach niestacjonarnego smarowania dla drgań...
-
Organic Pollution in Surface Waters from the Fuglebekken Basin in Svalbard, Norwegian Arctic
PublikacjaThe Fuglebekken basin is situated in the southern part of the island of Spitsbergen (Norwegian Arctic), on the Hornsund fjord (Wedel Jarlsberg Land). Surface water was collected from 24 tributaries (B1-B24) and from the main stream water in the Fuglebekken basin (25) between 10 July 2009 and 30 July 2009. The present investigation reveals the results of the analysis of these samples for their PAH and PCB content. Twelve of 16 PAHs...
-
Processing of Hydroacoustic and LiDAR Data for Three-dimensional Surface Reconstruction
PublikacjaThe technologies of sonar and laser scanning are commonly used for obtaining spatial information about underwater and over ground environments in the form of point clouds. Since this data model has known disadvantages, a more practical solution of visualising such data involves the creation of solid three-dimensional meshes composed of edges and facets. In this paper, several methods for 3D shape reconstruction of data obtained...
-
Numerical analysis of open channel steady gradually varied flow using the simplified saint-venant equations
PublikacjaFor one-dimensional open-channel flow modeling, the energy equation is usually used. There exist numerous approaches using the energy equation for open-channel flow computations, which resulted in the development of several very efficient methods for solving this problem applied to channel networks. However, the dynamic equation can be used for this purpose as well. This paper introduces a method for solving a system of non-linear...
-
Further development of the poroelastic road surface within the new Polish project SEPOR
PublikacjaRoad surfaces have a direct impact on noise generated by rolling tyres, the main and dominant source of noise of moving vehicles. Road surface texture, porosity and stiffness/elasticity govern the pavement contribution to tyre/road noise the most. An experimental PoroElastic Road Surface (PERS) is a wearing course with a high content of interconnected voids (pores) and with an elastic behavior due to the use of small particles...
-
Experimental study of flow boiling pressure drop and heat transfer of R1233zd(E) at moderate and high saturation temperatures
PublikacjaThe paper presents the results of experimental study of flow boiling of R1233zd(E) in minichannel at moderate and high saturation temperatures. The heat transfer coefficient and pressure drop were measured for flow boiling in a stainless steel tube with 2 mm inside diameter and a length of 300 mm. Experiment has been conducted for saturation temperatures ranging from 83 to 145 °C which corresponds to values of reduced pressures...
-
Inverse determination of sliding surface temperature based on measurements by thermocouples with account of their thermal inertia
PublikacjaThis study developed an inverse heat conduction algorithm to determine temperature at a sliding surface taking account of thermocouple thermal inertia. The direct heat conduction problem was solved analytically based on the Laplace integral transform approach. The inverse algorithm was applied to the problem of friction of a brake material against a steel. The experiments were conducted on a pin-on-disc tribometer for three short-time...
-
Characterizing surface and air temperature in the Baltic Sea coastal area using remote sensing techniques and GIS
PublikacjaEstimation of surface temperature using multispectral imagery retrieved from satellite sensors constitutes several problems in terms of accuracy, accessibility, quality and evaluation. In order to obtain accurate results, currently utilized methods rely on removing atmospheric fluctuations in separate spectral windows, applying atmospheric corrections or utilizing additional information related to atmosphere or surface characteristics...
-
Three modes of electrochemical impedance spectroscopy measurements performed on vanadium redox flow battery
PublikacjaThis article presents an innovative approach to monitor working redox flow batteries using dynamic electrochemical impedance spectroscopy, diverging from the commonly sequential impedance methods carried out under potentiostatic or galvanostatic conditions close to the open circle voltage. The authors introduce a fresh variation of dynamic impedance measurement that leverages an amplitude-modulated multi-frequency alternating current...
-
Wear Resistance Enhancement of Al6061 Alloy Surface Layer by Laser Dispersed Carbide Powders
PublikacjaIn this paper, results of the experimental study on improving wear resistance in sliding friction of Al-based alloy are presented. The technique used involves the formation of a metal matrix composite (MMC) in the alloy surface layer by laser dispersion of carbide powders such as WC, TiC and SiC. For WC and TiC MMC surface coatings fabricated under conditions typical for most of the technologically relevant solid-state lasers (wavelength...
-
EXPERIMENTAL STUDY OF SURFACE ROUGHNESS EFFECT ONTHE RHEOLOGICAL BEHAVIOR OF MR FLUID
PublikacjaPaper presents the results of shear stress measurements of a commercial magnetorheological fluid using a plate-plate type geometry with a modified working surface. The purpose of the study was to determine the effect of changing the roughness of the measuring plate on the obtained shear stress results. Controlled shear rate tests and Magneto Sweep measurements were carried out for three MR fluid layer heights. The tests were...
-
The influence of humic substances in treated sewage on the quality of surface waters
PublikacjaAt present the evaluation of WWTP effectiveness is based upon organic matter and nutrients removal. Recently it was found out that sewage treatment leads to formation of resistant to biochemical degradation organic compounds, similar to humic acids. The humic acids formed during sewage treatment process play diversified functions when discharged to surface waters - for instance they can act as carriers of hydrophobic organic pollutants...
-
Blade Section Prpfile Array Lifting Surface Design Method for Marine Screw Propeller Blade
PublikacjaThe lifting surface model is widely used in screw propeller design and analysis applications. It serves as a reliable tool for determination of the propeller blade mean line and pitch distribution. The main idea of this application was to determine the blade shape that would satisfy the kinematic boundary condition on its surface with the prescribed bound circulation distribution over it. In this paper a simplified lifting surface...
-
Electrohydrodynamic Flow Patterns in a Narrow Electrostatic Precipitator with Longitudinal Wire Electrode for Various Electrode Geometries
PublikacjaRecently narrow electrostatic precipitators (ESPs) have become a subject of interest because of their possible application in diesel engines. In this paper results of 2-dimensional (2D) Particle Image Velocimetry (PIV) measurements of the flow patterns in a narrow ESP for a various electrode geometries are presented. The PIV measurements were carried out in the observation plane that is perpendicular to the ESP duct. The ESP was...
-
Investigation of Liquid–Gas Flow in a Horizontal Pipeline Using Gamma-Ray Technique and Modified Cross-Correlation
PublikacjaThis article presents the application of the radioisotope absorption method in the study of two-phase water–air flow in a horizontal pipe. The measurement principle and the test stand are briefly described. The main part of the article presents the signal analysis methods applied to data obtained from scintillation detectors. Because these signals are mostly stochastic waveforms, they were analyzed statistically using the cross-correlation...
-
Experimental study on the selected aspects of bow thruster generated flow field at ship zero-speed conditions
PublikacjaThe paper presents the results of experimental study on the interaction between the bow thrusters understood as the flow field changes generated by bow tunnel thruster in deep water conditions operated as a single and twin units. The research was limited to zero-speed case for the ship dead in the water. The influence of the hull form and jet spread between the neighbouring thrusters for several combinations of the applied bow...
-
Overflowing tests at the Polish DredgDikes research dike – stability of the dike surface against erosion
PublikacjaIn the project DredgDikes the different research dike embankments were tested with respect to overflowing water induced erosion. Therefore, flumes were installed on the land side embankments in which the effect of overflowing water on the vegetated surface was investigated. On the Polish DredgDikes research dike near Gdansk, Poland, two parallel flumes were installed and the surface of the dike made of different mixtures of...
-
Wireless Local Area Network Technologies as Communication Solutions for Unmanned Surface Vehicles
PublikacjaAs the number of research activities and practical deployments of unmanned vehicles has shown a rapid growth, topics related to their communication with operator and external infrastructure became of high importance. As a result a trend of employing IP communication for this purpose is emerging and can be expected to bring significant advantages. However, its employment can be expected to be most effective using broadband communication...
-
Time Delay Estimation in Two-Phase Flow Investigation Using the γ-Ray Attenuation Technique.
PublikacjaTime delay estimation is an important research question having many applications in a range of technologies. Measurement of a two-phase flow in a pipeline or an open channel using radioisotopes is an example of such application. For instance, the determination of velocity of dispersed phase in that case is based on estimation of the time delay between two stochastic signals provided by scintillation probes. The proper analysis...
-
An Influence of Factors of Flow Condition, Particle and Material Properties on Slurry Erosion Resistance
PublikacjaThe degradation of materials due to slurry erosion is the serious problem which occurs in the power industries. The paper presents actual knowledge about an influence of individual factors connected with flow conditions, particles and material properties on the slurry erosion resistance. Among the factors connected with operating conditions, an influence of impact angle, and velocity of impact, particle concertation and liquid...
-
Spikes removal in surface measurement
Publikacja -
Phonons at the Fe(110) Surface
Publikacja -
Smoothing of wood surface by burnishing
PublikacjaW artykule zaprezentowano rozwój bezwiórowych metod obróbki wykańczającej drewna. Przedstawiono wpływ nagniatania ślizgowego na chropowatość powierzchni drewna. Badania przeprowadzono na próbkach wykonanych z drzewa sosnowego toczonych i nagniatanych ślizgowo. Nagniatanie ślizgowe przeprowadzono z wykorzystaniem nagniataka elastycznego o elemencie ślizgowym wykonanym z Karbonado. Wyniki odniesiono do głównych parametrów nagniatania...
-
Surface properties of barley straw
PublikacjaWłaściwości powierzchniowe słomy jęczmiennej (Hordeum vulgare) odgrywają kluczową rolę w zastosowaniach przemysłowych, takich jak sorpcja rozlewów olejowych oraz oczyszczenie gleby. Zbadano niejednorodność chemiczną oraz morfologiczną liści i łodyg słomy jęczmiennej poprzez pomiar kątów zwilżania wodą oraz olejem oraz z zastosowaniem techniki FTIR, SEM oraz AFM.
-
Dynamics of surface floating objects
PublikacjaPrezentowana praca stanowi wstępne rozeznanie w dziedzinie badań dynamiki konstrukcji pływających z zastosowaniem teorii procesu dyfuzji. W pracy rozpatrywane są modele fizyczne jednostek wielokadłubowych oraz modele matematyczne. Spośród modeli jednostek wielokadłubowych wyróżnia się modele deterministyczne oraz modele stochastyczne.
-
The surface photoconductivity in molecular layers
PublikacjaW pracy przedstawiono rezultaty analizy fotoprądów powierzchniowych w cienkich warstwach tetracenu i pentacenu. W szczególności badano wpływ obecności defektów strukturalnych w warstwach na charakterystyki fotoprądów i transport nośników ładunku.
-
Tyre/road noise reduction by a poroelastic road surface
PublikacjaLow noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory...
-
FEM approach to estimate the behaviour of biocomposite metal-surface coating system
PublikacjaA three dimensional (3D) model of biocomposite metal-surface coating system, which is influenced byknown external forces, is proposed. This model consists of the metallic substrate (Ti6Al4V) and thehydroxyapatite (HA) coating. Using FEM (finite element method), strain-stress maps of model weregenerated for investigating relations between the extreme stress of HA coating and the magnitude ofexternal force and the thickness of the...
-
INFORMATION ABOUT DYNAMICS OF THE SEA SURFACE AS A MEANS TO IMPROVE SAFETY OF THE UNMANNED VESSEL AT SEA
PublikacjaOne of the fundamental states of the sea surface is its heave. Despite of years of the intense scientific inquiry, no clear understanding of the influence of this aspect on the dynamics of the sea environment has emerged. The separation of two nearby fluid elements which one may observed for example as a free floating of small objects on the sea surface (rescuers on the rough sea or small research vessels) is caused by the interaction...
-
Measurement system for nonlinear surface spectroscopy by atomic force microscopy for corrosion processes monitoring
PublikacjaIn addition to traditional imaging the surface, atomic force microscopy (AFM) enables wide variety of additional measurements. One of them is higher harmonic imaging. In tapping mode the nonlinear contact between tip and specimen results in higher frequency vibrations. More information available from the higher harmonics analysis proves to be helpful for more detailed imaging. Such visualization is especially useful for heterogeneous...
-
The use of Response Surface Methodology for reliability estimation of aluminum silo subjected to wind load
PublikacjaAn axisymmetric aluminum silo model with a single, standardized geometric imperfection of its lateral surface is considered. The silo is wind – loaded only. The paper is focused on the critical, or limit value of wind pressure, both producing a loss of stability of the silo. This value is affected by vertical coordinate (position) of the imperfection and the angular relation between the imperfection and the wind direction. Reliability...
-
Decomposition of halogenated nucleobases by surface plasmon resonance excitation of gold nanoparticles
PublikacjaHalogenated uracil derivatives are of great interest in modern cancer therapy, either as chemotherapeutics or radiosensitisers depending on their halogen atom. This work applies UV-Vis spectroscopy to study the radiation damage of uracil, 5-bromouracil and 5- uorouracil dissolved in water in the presence of gold nanoparticles upon irradiation with an Nd:YAG ns-pulsed laser operating at 532nm at dierent uences. Gold nanoparticles...
-
Analysis of the Ways to Identify Rail Running Surface Defects by Means of Vibration Signals
PublikacjaTh e article discusses a preliminary concept of a method enabling the identifi cation of chosen rail running surface defects, such as squats, spalling, and running surface defects, by analysing the parameters of vibration signals. It features a description of the methodology of the conducted tests, the scope thereof, and the selection of the measurement points with specifi c defect types. Th e article covers selected results of...
-
Extraction and evaluation of gas-flow-dependent features from dynamic measurements of gas sensors array
PublikacjaGas analyzers based on gas sensors are the devices which enable recognition of various kinds of volatile compounds. They have continuously been developed and investigated for over three decades, however there are still limitations which slow down the implementation of those devices in many applications. For example, the main drawbacks are the lack of selectivity, sensitivity...
-
Flow cytometric approach to evaluate the impact of hydro-technical concrete compounds’ release to the freshwater microbiome
PublikacjaThe aim of this research was to test the potential of applying a flow cytometric procedure to evaluate the impact of concrete compounds’ release to the freshwater microbiome. Cells from the collected samples were stained with a fluorogenic redox indicator dye that measures the redox potential of microbial cells. This novel approach was combined with the assessment of microorganisms’ penetration into the internal structures of concrete...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublikacjaThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Practical aspects of Flow Thinning optimization
Publikacja -
Complexity of a classical flow restoration problem
Publikacja -
Isotropic damage in viscoplastic flow conditions
PublikacjaMechanika zniszczenia jest obecnie jedną z ważniejszych gałęzi mechaniki ciał stałych. Jest cały czas rozwijającą się dziedziną nauki, która znalazła swoje zastosowania w problemach inżynierskich. W artykule zaprezentowano podstawowe informacje na temat lepkoplastyczności i jej zastosowania, koncepcję mechanicznej reprezentacji zniszczenia przez zmienną D, koncepcję naprężeń efektywnych, równania opisujące zniszczenie oraz lepkoplastyczny...
-
Modelling of dryout process in an annular flow
PublikacjaW pracy pokazano teoretyczny model kryzysu wrzenia przy wysokich stopniach suchości, który jest modyfikacją modelu proponowanego wcześniej przez Sedlera i Mikielewicza. Model wysychania filmu cieczowego w przepływie pierścieniowym składa się z różniczkowych równań bilansu masy zapisanych dla filmu na ściance i kropel w rdzeniu przepływu. Rozwiązanie układu równań wymaga znajomości gęstości strumienia masy kropel wytrącających się...
-
The wastewater flow through trickling filters.
PublikacjaFiltry zraszane projektowane są głównie w oparciu o wytyczne techniczne. W pracy zaproponowano metodę o charakterze strukturalnym. Pokazano sposób określania miarodajnego czasu przebywania cieczy w układzie i powiązania go z kinetyczną charakterystyką procesu oczyszczania ścieków.
-
Flow Control Algorithm for UMTS HSDPA
PublikacjaHSDPA (High Speed Downlink Packet Access) jest istotnym etapem ewolucji systemu UMTS. Pozwala na transmisję do użytkownika z prędkością dochodzącą do 14.4 Mbit/s; aby to umożliwić, wprowadzono w wersji 5 UMTS szereg nowych mechanizmów w warstwie fizycznej oraz MAC. W tej pracy przedstawiono szczegółową analizę jednego z nowych mechanizmów - algorytmu kontroli natężenia ruchu między MAC-hs i MAC-d. Zaproponowano nowy, efektywny...
-
Modelling of heat transfer in flow boiling
PublikacjaW pracy przedstawiono zagadnienia związane z modelowaniem wrzenia w przepływie w kanałach o małej średnicy. Przedstawiono modyfikację rozwijanej przez autorów korelacji umożliwiającej wyznaczanie współczynnika przejmowania ciepła podczas wrzenia w przepływie.
-
Modelling of dryout process in annular flow
PublikacjaW pracy pokazano teoretyczny model kryzysu wrzenia przy wysokich stopniach suchości, który jest modyfikacją modelu proponowanego wcześniej przez Sedlera i Mikielewicza. Model wysychania filmu cieczowego w przepływie pierścieniowym składa się z różniczkowych równań bilansu masy zapisanych dla filmu na ściance i kropel w rdzeniu przepływu. Rozwiązanie układu równań wymaga znajomości gęstości strumienia masy kropel wytrącających się...
-
Dryout in annular flow - theoretical analysis
PublikacjaW pracy zaprezentowano model kryzysu wrzenia w przepływie pierścieniowym, obowiązujący dla wysokich wartości stopnia suchości i stanowiący modyfikację wcześniejszej wersji modelu zaproponowanego przez Sedlera i Mikielewicza. Model ten uwzględnia bilans masy w filmie cieczowym i bilans masy dla kropel cieczy w rdzeniu przepływu oraz zawiera dodatkowy człon odpowiedzialny za odparowanie filmu na ściance kanału. Rozwiązanie układu...
-
Application of tomography to granular silo flow.
PublikacjaPublikacja zawiera opis wyników badań doświadczalnych nad efektami dynamicznymi podczs opróżniania silosów z zastosowaniem tomografii pojemnościowej.
-
Correlation between Fractal Dimension and Areal Surface Parameters for Fracture Analysis after Bending-Torsion Fatigue
PublikacjaThis paper investigates the fracture surface topography of two steel and aluminum alloys subject to bending-torsion fatigue loadings, as well as their susceptibility to fatigue performance and failure mechanisms. Using fracture surface topography data analysis, elements with different geometries were elaborated. A correlation between the fractal dimension, other selected parameters of surface topography such as areal Sx, and...
-
Research into the Movements of Surface Water Masses in the Basins Adjacent to the Port
PublikacjaThis paper presents the results of the practical and simulation research into determining the routes of movement of small objects moving together with surface water masses in basins adjacent to the port. The results of this research were referenced against the modelling of routes of small objects in port channel basins. The results of practical research concerning the movement of small objects in basins adjacent to the port were...