Filtry
wszystkich: 1145
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: LASER COMPUTED TOMOGRAPHY
-
Radar Signal Parameters Estimation Using Phase Accelerogram in the Time-Frequency Domain
PublikacjaRadar signal parameter estimation, in the context of the reconstruction of the received signal in a passive radar utilizing other radars as a source of illumination, is one of the fundamental steps in the signal processing chain in such a device. The task is also a crucial one in electronic reconnaissance systems, e.g. ELINT (Electronic Intelligence) systems. In order to obtain accurate results it is important to measure, estimate...
-
Adhesive compliance effect in mode I separation:Profilometry approach
PublikacjaThe effect of adhesive compliance on the deflection of a loaded, bonded beam was studied using laser profilometry. Experimental data obtained were compared with both Euler-Bernoulli (encastré) and Winkler (one parameter elastic foundation) models. A third, analytical, 2D model, based on shear within the adhesive layer (two parameter elastic foundation), was introduced. Finite element analysis (FEA) was also used to study the effect...
-
Formation and Growth of the Crack in Bonded Joints Under Mode I Fracture: Substrate Deflection at Crack Vicinity
PublikacjaAdhesive bonding is now commonly used in aircraft, cars, boats, etc. In these applications, thin panels are often bonded. In such thin structures, heterogeneous mechanical loading along the bondline edge (or potential crack front), is likely to arise due to 3D structural effects. The crack front and its vicinity is a special region, in that it is where structural properties of the adherend material meet those of the adhesive (discontinuity)....
-
Experimental results of full scattering profile from finger tissue-like phantom
PublikacjaHuman tissue is one of the most complex optical media since it is turbid and nonhomogeneous. We suggest a new optical method for sensing physiological tissue state, based on the collection of the ejected light at all exit angles, to receive the full scattering profile. We built a unique set-up for noninvasive encircled measurement. We use a laser, a photodetector and finger tissues-mimicking phantoms presenting different optical...
-
UAV IN TODAYS PHOTOGRAMMETRY – APPLICATION AREAS AND CHALLENGES
PublikacjaThere a few important factors, that nowadays, unmanned aerial vehicles (UAV) are used by wider community, and for cases and applications, that cannot be performed never before. Small UAVs, as a photogrammetry measurement tool provide flexibility, reliability, are safe and easy to use, can be deployed in minutes, initial measurement can be delivered yet on the field, and final accurate measurements are calculated in a very short...
-
Full scattering profile of circular optical phantoms mimicking biological tissue
PublikacjaHuman tissue is one of the most complex optical media since it is turbid and nonhomogeneous. In our poster, we suggest a new type of skin phantom and an optical method for sensing physiological tissue condition, basing on the collection of the ejected light at all exit angles, to receive the full scattering profile. Conducted experiments were carried out on an unique set-up for noninvasive encircled measurement. Set-up consisted...
-
Pomiarowa analiza drgań tarcz łożyskowych silników asynchronicznych laserem skanującym SLDV
PublikacjaArtykuł przedstawia analizę pomiarową tarcz łożyskowych silników asynchronicznych badanych przy wykorzystaniu lasera skanującego SLDV (Scanning Laser Doppler Vibrometer) na przykładzie urządzenia Polytec PSV-400. Przedstawiono istotę problemu drgań wibroakustycznych małych silników asynchronicznych powszechnie spotykanych w przemyśle. Przedstawione zostały teoretyczne wyliczone reluktancyjne składowe naprężeń promieniowych oddziałowujące...
-
On the necessity of experimental verification of numerical results in biomedical applications
PublikacjaPorous structures made of metal or biopolymers with a structure similar in shape and mechanical properties to human bone can be easily produced by stereolitography techniques, e.g. selective laser melting (SLM). Numerical techniques, like finite element method (FEM) have great potential in testing new, even the most sophisticated designs, according to their mechanical properties, i.e. strength or stiffness. However, due to different...
-
Very accurate time propagation of coupled Schrödinger equations for femto- and attosecond physics and chemistry, with C++ source code
PublikacjaIn this article, I present a very fast and high-precision (up to 33 decimal places) C++ implementation of the semi-global time propagation algorithm for a system of coupled Schrödinger equations with a time-dependent Hamiltonian. It can be used to describe time-dependent processes in molecular systems after excitation by femto- and attosecond laser pulses. It also works with an arbitrary user supplied Hamiltonian and can be used...
-
Nano Tin/Tin Oxide Attached onto Graphene Oxide Skeleton as a Fluorine Free Anode Material for Lithium-Ion Batteries
PublikacjaHerein, we show a composite formation method of tin/tin oxide nanoparticles with graphene oxide and CMC based on laser ablation technique as an electrode material for energy storage devices. The material exhibited a three-dimensional conducting graphene oxide network decorated with tin or tin oxide nanoparticles. The structure, homogeneous distribution of nanoparticles, and direct contact between inorganic and organic parts were...
-
Properties of Barium Cerate-Zirconate Thin Films
PublikacjaIn this work, we review several experimental results showing the electrical properties of barium cerate-zirconate thin films and discuss them in view of the possible influence of various factors on their properties. Most of the presented Ba(Ce, Zr, Y)O3 thin films were formed by the pulsed laser deposition (PLD) technique, however thin films prepared using other methods, like RF magnetron sputtering, electron-beam deposition, powder...
-
Microfluidic devices for photo-and spectroelectrochemical applications
PublikacjaThe review presents recent developments in electrochemical devices for photo- and spectroelectrochemical investigations, with the emphasis on miniaturization (i.e., nanointerdigitated complementary metal-oxide-semiconductor devices, micro- and nano-porous silicon membranes or microoptoelectromechanical systems), silica glass/microreactors (i.e., plasmonic, Raman spectroscopy or optical microcavities) or polymer-based devices (i.e.,...
-
Autonomous Control of the Underwater Remotely Operated Vehicle in Collision Situation with Stationary Obstacle
PublikacjaThe article considers the problem of autonomous control of the underwater remotely operated vehicle mini Remotely Operated Vehicle (ROV) in a collision situation with a stationary obstacle. The control of the collision avoidance process is presented as a synthesis of fuzzy proportional-differential controllers for the control of distance and orientation concerning the detected stationary obstacle. The control of the submergence...
-
The role of low-energy electrons in the charging process of LISA test masses
PublikacjaThe estimate of the total electron yield is fundamental for our understanding of the test-mass charging associated with cosmic rays in the Laser Interferometer Space Antenna (LISA) Pathfinder mission and in the forthcoming gravitational wave observatory LISA. To unveil the role of low energy electrons in this process owing to galactic and solar energetic particle events, in this work we study the interaction of keV and sub-keV...
-
Active IR-Thermal Imaging in Medicine
PublikacjaIn this paper we summarize results of several research projects devoted to development of new diagnostic methods and procedures based on quantitative infrared thermography in medical applications. First, basics of active dynamic thermography are presented. Described are both, instrumentation and software comprising measurement procedures including collection of series of IR-images after external excitation, data treatment with...
-
POM/EVA Blends with Future Utility in Fused Deposition Modeling
PublikacjaPolyoxymethylene (POM) is one of the most popular thermoplastic polymers used in the industry. Therefore, the interest in its potential applications in rapid prototyping is understandable. Nevertheless, its low dimensional stability causes the warping of 3D prints, limiting its applications. This research aimed to evaluate the effects of POM modification with ethylene-vinyl acetate (EVA) (2.5, 5.0, and 7.5 wt.%) on its processing...
-
Optical Parameters Stability Over Time of Porous Phantoms Mimicking Tissues
Dane BadawczeOptical phantoms are used to validate optical measurement methods. The stability of their optical parameters over time allows them to be used and stored over long-term periods while maintaining their optical parameters. The aim of the presented research was to investigate the stability of fabricated porous phantoms, which can be used as a lung phantom...
-
Gas Detection Using Resistive Gas Sensors And Radial Basis Function Neural Networks
PublikacjaWe present a use of Radial Basis Function (RBF) neural networks and Fluctuation Enhanced Sensing (FES) method in gas detection system utilizing a prototype resistive WO3 gas sensing layer with gold nanoparticles. We investigated accuracy of gas detection for three different preprocessing methods: no preprocessing, Principal Component Analysis (PCA) and wavelet transformation. Low frequency noise voltage observed in resistive gas...
-
Numerical Simulation of Catastrophic Flood: the Case Study of Hypothetical Failure of the Bielkowo Hydro–Power Plant Reservoir
PublikacjaThe numerical modeling of flood wave propagation following the hypo-thetical breaks of the embankments of the Bielkowo hydro–power plant storage reservoir (Kolbudy II Reservoir) on the Radunia River in Poland have been presented. The results of computations were used to estimate the parameters of the flood waves, which are indispensable for the flood zone determination and mapping and then for the flood risk analysis. When estimating...
-
Dome over the Gdynia seaport building
PublikacjaThe paper presents the description of structure and the selected problems of the technical condition, as well as the strength analysis of the thin-walled reinforced concrete shell which has been making a covering of the main hall of the Gdynia Seaport Building through the last 80 years. The rectangle projection of four single curvature shells of the dome was shaped out of mutual perpendicular intersection of two cylindrical shells. The...
-
Variable Fractional Delay Filter Design Using a Symmetric Window
PublikacjaIn this paper a numerically efficient method for designing a nearly optimal variable fractional delay (VFD) filter based on a simple and well-known window method is presented. In the proposed method a single window extracted from the optimal filter with fixed fractional delay (FD) is divided into even and odd part. Subsequently, the odd part is discarded and symmetric even part of the extracted window is used to design a family...
-
Bifractal receiver operating characteristic curves: a formula for generating receiver operating characteristic curves in credit-scoring contexts
PublikacjaThis paper formulates a mathematical model for generating receiver operating characteristic (ROC) curves without underlying data. Credit scoring practitioners know that the Gini coefficient usually drops if it is only calculated on cases above the cutoff. This fact is not a mathematical necessity, however, as it is theoretically possible to get an ROC curve that keeps the same Gini coefficient no matter how big a share of lowest...
-
Effect of surface on the flexomagnetic response of ferroic composite nanostructures; nonlinear bending analysis
PublikacjaOur analysis incorporates the geometrically nonlinear bending of the Euler-Bernoulli ferromagnetic nanobeam accounting for a size-dependent model through assuming surface effects. In the framework of the flexomagnetic phenomenon, the large deflections are investigated referring to von-Kármán nonlinearity. Employing the nonlocal effects of stress coupled to the gradient of strain generates a scale-dependent Hookean stress-strain...
-
Wavelet filtering of signals without using model functions
PublikacjaThe effective wavelet filtering of real signals is impossible without determining their shape. The shape of a real signal is related to its wavelet spectrum. For shape analysis, a continuous color wavelet spectrogram of signal level is often used. The disadvantage of continuous wavelet spectrogram is the complexity of analyzing a blurry color image. A real signal with additive noise strongly distorts the spectrogram based on continuous...
-
A Wideband Rotary-Joint-Free H-Plane Horn Antenna With 360° Steerable Radiation Pattern Using Gap Waveguide Technology
PublikacjaConsidering the limitations of electronically steerable antennas such as limited steering span, gain degradation for large steering angles, complexity, and cost, this article is focused on the design of a simple mechanically steerable H-plane horn antenna. It is shown that since there is no need for an electrical connection between the top and bottom sections of a gap waveguide (GWG), if a sectoral horn is properly designed and realized...
-
The Impact of Material Selection on Durability of Exhaust Valve Faces of a Ship Engine – A Case Study
Publikacjawo alloys were used in order to extend the service life of marine engine exhaust valve head. Layers of cobalt base alloys were made of the powders with with chemical composition as follow: the layer marked L12; C-1,55%; Si-1,21%; Cr-29,7%; W-9%; Ni-2%; Mo<0,01%; Fe-1,7%; Co-54,83% and the layer marked N; C-1,45%; Co-38,9%; Cr-24,13%; Ni-10,43%; W-8,75%; Fe-7,64%; Mo-7,56%; Si-2,59%. Base metal was valve steel after heat treatment....
-
Widening of the electroactivity potential range by composite formation – capacitive properties of TiO2/BiVO4/PEDOT:PSS electrodes in contact with an aqueous electrolyte
PublikacjaComposites based on the titania nanotubes were tested in aqueous electrolyte as a potential electrode material for energy storage devices. The nanotubular morphology of TiO2 was obtained by Ti anodization. TiO2 nanotubes were covered by a thin layer of bismuth vanadate using pulsed laser deposition. The formation of the TiO2/BiVO4 junction leads to enhancement of pseudocapacitance in the cathodic potential range. The third component,...
-
Multibeam Echosounder and LiDAR in Process of 360-Degree Numerical Map Production for Restricted Waters with HydroDron
PublikacjaIn order to increase the safety of inland navigation and facilitate the monitoring of the coastal zone of restricted waters, a model of multi-sensory fusion of data from hydroacoustic and optoelectronic systems mounted on the autonomous survey vessel HydroDron will be developed. In the research will be used the LiDAR laser scanner and multibeam echosounder. To increase the visual quality and map accuracy, additionally side scan...
-
The Influence of Selected Parameters of Numerical Modelling on Strains and Stresses at Weld Toe Notch
PublikacjaLatest development in the field of welding technology and prefabrication enabled massive production of thin-walled sandwich structures. Multi-layered sandwich structures are fabricated with the use of high-power CO2 lasers, friction welding, arc welding, hybrid welding, or other technique designed for the special purpose. Steel or aluminium alloy plates with thickness between 1 and 5 mm are connected by internal stiffeners. Strength...
-
On-line measurement of wood surface smoothness
PublikacjaThe latest progress in the field of optics and microelectronics resulted in development of new generation vision systems capable of scanning surface topography with very high sampling frequencies. The blue color of illuminating light as well as novel systems for controlling ultra-thin laser line thickness allows measurement of the porous surface of wood with a triangulation method. Three alternative sensors were tested here in...
-
Design of dimensionally stable composites using efficient global optimization method
PublikacjaDimensionally stable material design is an important issue for space structures such as space laser communication systems, telescopes, and satellites. Suitably designed composite materials for this purpose can meet the functional and structural requirements. In this paper, it is aimed to design the dimensionally stable laminated composites by using efficient global optimization method. For this purpose, the composite plate optimization...
-
REVIEW OF CURRENT RESEARCH ON CHITOSAN AS A RAW MATERIAL IN THREE-DIMENSIONAL PRINTING TECHNOLOGY IN BIOMEDICAL APPLICATIONS
PublikacjaThree-dimensional (3D) biomaterial manufacturing strategies show an extraordinary driving force for the development of innovative solutions in the biomedical sector, including drug delivery systems, disease modelling and tissue and organ engineering. Due to its remarkable and promising biological and structural properties, chitosan has been widely studied for decades in several potential applications in the biomedical field. However,...
-
Finite element modelling of a historic church structure in the context of a masonry damage analysis
PublikacjaThe paper includes a case study of modelling a real historic church using the finite element method (FEM) based on laser scans of its geometry. The main goal of the study was the analysis of the causes of cracking and crushing of masonry walls. An FEM model of the structure has been defined in ABAQUS. A non-linear dynamic explicit analysis with material model including damage plasticity has been performed. A homogenization procedure...
-
Design and Experiments of a Piezoelectric Motor Using Three Rotating Mode Actuators
PublikacjaThis paper represents a numerical and experimental investigation of the multicell piezoelectric motor. The proposed design consists of three individual cells that are integrated into the stator, double rotor, and a preload system combined into a symmetrical structure of the motor. Each of the cells is characterized by a traveling wave and rotating mode motor. A finite element numerical analysis is carried out to obtain optimal...
-
Quasistatic and fatigue behavior of an AISI H13 steel obtained by additive manufacturing and conventional method
PublikacjaThis work aims to compare the mechanical behavior of an AISI H13 steel obtained by additive manufacturing with that obtained by conventional manufacturing methods. The average values of the ultimate tensile strength (UTS) and ductility obtained for the specimens produced by the conventional method were equal to 658 MPa and 18%, respectively, which compares with 503 MPa and 0.75% registered for the selective laser melting (SLM)...
-
Fast Design Optimization of Waveguide Filters Applying Shape Deformation Techniques
PublikacjaThis paper presents an efficient design of microwave filters by means of geometry optimization using shape deformation techniques. This design procedure allows for modelling complex 3D geometries which can be fabricated by additive manufacturing (AM). Shape deforming operations are based on radial basis function (RBF) interpolation and are integrated into an electromagnetic field simulator based on the 3D finiteelement method (FEM)....
-
Aiswarya Manohar
OsobyI joined as a PhD student in Gdansk tech university of Technology in 2022. In my scientific work, I am primarily focusing on studies related to 3D printing, laser induced graphene, electrochemical sensors and biosensors as well as micro arc oxidation, corrosion, and degradation with emphasis on impedance spectroscopy studies of electrode processes. I am specializing in Materials and surface modifications and characterization. ...
-
The mechanisms of degradation of titanium dental implants
PublikacjaTitanium dental implants show very good properties, unfortunately there are still issues regarding material wear due to corrosion, implant loosening, as well as biological factors—allergic reactions and inflammation leading to rejection of the implanted material. In order to avoid performing reimplantation operations, changes in the chemical composition and/or modifications of the surface layer of the materials are used. This research...
-
Rotational molding of polylactide (PLA) composites filled with copper slag as a waste filler from metallurgical industry
PublikacjaThe research work carried out so far indicates the ever wider possibilities and demand for shaping composite products in the rotational molding technology. This trend was the main reason to use waste-based filler from the metallurgical process as a filler for manufacturing polylactide (PLA)-based remolded composites. Copper slag (CS) was introduced in the single-step processing method to PLA matrix at 5, 10, 20, and 35 wt%. The...
-
Influence of Surface-Modified Montmorillonite Clays on the Properties of Elastomeric Thin Layer Nanocomposites
PublikacjaIn recent years, polyurethane nanocomposites have attracted more attention due to the massive demand for materials with increasingly exceptional mechanical, optical, electrical, and thermal properties. As nanofillers have a high surface area, the interaction between the nanofiller and the polymer matrix is an essential issue for these materials. The main aim of this study is to validate the impact of the montmorillonite nanofiller...
-
Applying the Lombard Effect to Speech-in-Noise Communication
PublikacjaThis study explored how the Lombard effect, a natural or artificial increase in speech loudness in noisy environments, can improve speech-in-noise communication. This study consisted of several experiments that measured the impact of different types of noise on synthesizing the Lombard effect. The main steps were as follows: first, a dataset of speech samples with and without the Lombard effect was collected in a controlled setting;...
-
On implementation of fibrous connective tissues’ damage in Abaqus software
PublikacjaConnective fibrous tissues, such as tendons and ligaments, in humans and animals exhibit hyperelastic behaviour. The constitution of the material of these tissues is anisotropic due to the presence of the collagen fibres, where one family of fibres is the typical case. Traumatic events and/or aging may sometimes lead to the damage of the tissue. The study of motion of affected joints or limbs is usually not permitted in vivo. This...
-
Multiparameter sensitivity analysis of a GFRP composite footbridge of a sandwich structure and U-shaped cross-section
PublikacjaThe paper deals with multiparameter sensitivity analysis of a composite footbridge. A shell‐like structure is 14.5 m long shows U‐shaped cross‐section and inner service dimensions 1.3 × 2.5 m. Glass fiber reinforced polymer GFRP laminate constitutes faces of a sandwich structure while PET foam received from recycled bottle builts a core. The structure was divided into 285 independent areas where the thickness of laminates and stiffness...
-
Pressure effects on the electronic structure and superconductivity of (TaNb)0.67(HfZrTi)0.33 high entropy alloy
PublikacjaEffects of pressure on the electronic structure, electron-phonon interaction, and superconductivity of the high entropy alloy ( TaNb ) 0.67 ( HfZrTi ) 0.33 are studied in the pressure range 0–100 GPa. The electronic structure is calculated using the Korringa-Kohn-Rostoker method with the coherent potential approximation. Effects of pressure on the lattice dynamics are simulated using the Debye-Grüneisen model and the Grüneisen...
-
Water Behavior Near the Lipid Bilayer
PublikacjaIn this chapter, we focus on the dynamics of water molecules situated in the vicinity of a phospholipid bilayer. Using a molecular dynamics simulation method, we studied interactions between water and the bilayer and tracked trajectories of the water molecules. Based on the hypothesis that molecules trapped inside the bilayer make different motions than the ones which are either attached to the surface or move freely in the water...
-
Guanosine Dianions Hydrated by One to Four Water Molecules
PublikacjaIntermolecular interactions such as those present in molecule···water complexes may profoundly influence the physicochemical properties of molecules. Here, we carried out an experimental–computational study on doubly deprotonated guanosine monophosphate···water clusters, [dGMP – 2H]2–·nH2O (n = 1–4), using a combination of negative anion photoelectron spectroscopy (NIPES) with molecular dynamics (MD) and quantum chemical (QM) calculations....
-
Method of selective fading as a educational tool to study the behaviour of prestressed concrete elements under excess loading
PublikacjaPrestressed structures are a key to realization of the boldest architectural ideas, characteristic feature of prestressed structure is better use of concrete material properties by insertion of internal forces. Learning about pre-stressed reinforced concrete structures is an integral part of Graduate Studies Program in construction engineering. Know-how of geometry change patterns in prestressed concrete elements under certain...
-
Inżynieria odwrotna bazy paliw płynnych w Gdańsku
PublikacjaArtykuł prezentuje prace z zakresu pozyskania danych o zbiornikach bazy paliw płynnych w Gdańsku. Przedstawione rozwiązanie nie ogranicza się tylko do stworzenia (rejestracji) chmury punktów, ale jest próbą wskazania użycia naziemnego skaningu laserowego do stworzenia bazy informacji o bazie paliw – w tym głównie geometrii zbiorników. Autorzy prezentują proces inwentaryzacji, rejestrację chmury punktów oraz wskazują zasady tworzenia...
-
Wytwarzanie i modyfikacja powierzchni porowatych struktur tytanowych przeznaczonych na implanty
PublikacjaCelem pracy było wytworzenie stopu Ti-13Nb-13Zr z wykorzystaniem technologii selektywnego topienia laserowego (SLM) oraz jego biofunkcjonalizacja za pomocą utleniania mikrołukowego (MAO), a następnie określenie wpływu parametrów procesowych na właściwości otrzymanych materiałów pod kątem ich zastosowania na implanty. Oceniono wpływ napięcia, natężenia i czasu procesu MAO przeprowadzanego w elektrolicie zawierającym wapń i fosfor...
-
Architectural Heritage Virtual Models in Conservation Practice
PublikacjaThe article presents the issues concerning architectural heritage digital models’ applications in conservation practice. These considerations are discussed in the context of the commencement of creating virtual models regarding no-longer existing historical buildings in the first half of the 1980s. Such models’ applications and possible uses are analyzed within the adopted criteria that distinguish the following model types....