wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: COMMON CAUSE FAILURES
-
ASSESSING THE POTENTIAL REPLACEMENT OF MINERAL OIL WITH ENVIRONMENTALLY ACCEPTABLE LUBRICANTS IN A STERN TUBE BEARING: AN EXPERIMENTAL ANALYSIS OF BEARING PERFORMANCE
PublikacjaT his study compares the performance of a plain bearing, with a similar structure to a tail shaft stern bearing, lubricated with either mineral oil or an environmentally acceptable lubricant (EAL). The main characteristic of the bearing is its length/diameter ratio of <1. Measurements are carried out with the bearing operating under loads from 0.5 to 1 MPa and seven speeds ranging from 1 to 11 rev/s. The bearing lubricated...
-
Endothelial Dysfunction Driven by Hypoxia—The Influence of Oxygen Deficiency on NO Bioavailability
PublikacjaCardiovascular diseases (CVDs) are the leading cause of death worldwide. The initial stage of CVDs is characterized by endothelial dysfunction, defined as the limited bioavailability of nitric oxide (NO). Thus, any factors that interfere with the synthesis or metabolism of NO in endothelial cells are involved in CVD pathogenesis. It is well established that hypoxia is both the triggering factor as well as the accompanying factor...
-
Soiling Effect Mitigation Obtained by Applying Transparent Thin-Films on Solar Panels: Comparison of Different Types of Coatings
PublikacjaDust accumulation on the front cover of solar panels is closely linked to location and orientation of photovoltaic (PV) installation. Its build-up depends on the module tilt angle, frequency of precipitation, humidity, wind strength and velocity, as well as grain size. Additionally, soil composition is determined by solar farm surroundings such as local factories, agricultural crops, and traffic. Over time, molecules of atmospheric...
-
Metal dusting phenomena of 501 AISI furnace tubes in refinery fractional distillation unit
PublikacjaThe purpose of this investigation was to conduct the failure analysis of 501 AISI furnace tubes places before distillation column in fractional distillation unit. The investigated furnace tubes were planned to work for ten years however after just two years of exploitation <30% of the material left. The observed corrosion process had the intense and complex character. The well-adhered shiny black deposits and deep, round pits were...
-
How high-tech solutions support the fight against IUU and ghost fishing: a review of innovative approaches, methods, and trends
PublikacjaIllegal, Unreported, and Unregulated fishing is a major threat to human food supply and marine ecosystem health. Not only is it a cause of significant economic loss but also its effects have serious long-term environmental implications, such as overfishing and ocean pollution. The beginning of the fight against this problem dates since the early 2000s. From that time, a number of approaches and methods have been developed and reported....
-
Machine learning approach to packaging compatibility testing in the new product development process
PublikacjaThe paper compares the effectiveness of selected machine learning methods as modelling tools supporting the selection of a packaging type in new product development process. The main goal of the developed model is to reduce the risk of failure in compatibility tests which are preformed to ensure safety, durability, and efficacy of the finished product for the entire period of its shelf life and consumer use. This kind of testing...
-
Estimation of smokers' exposure to mercury from combustible tobacco products, based on the approach used in food consumers’ exposure estimation
PublikacjaSmoking has been known to mankind for centuries, but it is only in recent decades that much attention has been paid to the harmfulness of this habit. Mercury inhalation is particularly dangerous in this respect and smoking creates extremely favorable conditions for the emission and targeted delivery of this element into the lungs. Despite this fact, a lack of a clear method for estimating the exposure of tobacco consumers to mercury...
-
Assessment of student language skills in an e-learning environment
PublikacjaThis article presents the role of various assessment structures that can be used in a VLE. e-Learning language courses offer tutors a wide range of traditional and computer-generated formative and summative assessment procedures and tools. They help to evaluate each student’s progress, monitor their activities and provide varied support, which comes from the tutor, the course structure and materials as well as other participants....
-
Risk of Delays in Implementation of Building Investment in Urban Conditions in the Aspect of Historical Background of its Location
PublikacjaThe implementation of a construction investment in urban conditions is extremely complex, and at the same time exposed to a high risk of a specific character. In case of construction investment located in the historic part of the city, the possible accumulation of many unfavourable factors, which in course of its implementation, may constitute a serious source of delays and disruptions, should be taken into account at the preparation...
-
Using UAV Photogrammetry to Analyse Changes in the Coastal Zone Based on the Sopot Tombolo (Salient) Measurement Project
PublikacjaThe main factors influencing the shape of the beach, shoreline and seabed include undulation, wind and coastal currents. These phenomena cause continuous and multidimensional changes in the shape of the seabed and the Earth’s surface, and when they occur in an area of intense human activity, they should be constantly monitored. In 2018 and 2019, several measurement campaigns took place in the littoral zone in Sopot, related to...
-
The reliability of tree and star networks.
PublikacjaOne of the important parameters characterizing the quality of computer networks is the network's reliability with respect to failures of the communication links and nodes. This chapter investigated the reliability of tree and star networks. The tree and star topology is used in centralized computer networks. In centralized computer networks all communication must take place through some central computer. Following measures of network...
-
Functional safety and human factors
PublikacjaRozdział przedstawia istotny problem uwzględnienia czynników ludzkich (H&OF) w analizie bezpieczeństwa funkcjonalnego, które wpływają istotnie na bezpieczeństwo przemysłowych obiektów podwyższonego ryzyka, nie ujęty jednak w normach bezpieczeństwa funkcjonalnego. Przedstawia się metody analizy niezawodności człowieka (HRA) w kontekście tych czynników, które wpływają na błędy człowieka. Czynniki ludzkie i organizacyjne powinny być...
-
Structural analysis as a supporting method for the research of the medieval brick architecture
PublikacjaChronology of brick historical buildings might be established much more precisely than the chronology of stone ones due to the architectural and metrical analysis of bricks, mortars and brickworks. Comparison of historical sources allows to reconstruct the previous stages of constructing monuments. Causations between transformations and developments of monuments are usually interpreted as the results of artistic or ideological...
-
Kobieta ciężarna i alkohol-toksyczny związek. Smółka noworodków jako materiał w diagnostyce spożywania alkoholu w czasie ciąży
PublikacjaKażda ilość alkoholu spożyta przez ciężarną kobietę może spowodować poronienie, przedwczesny poród, patologię łożyska, zahamowanie wzrostu wewnątrzmacicznego płodu i wystąpienie licznych wad wrodzonych wywołanych alkoholem, określanych wspólnie mianem spektrum płodowych zaburzeń alkoholowych - FASD. Mogą one objawiać się zaburzeniami psychicznymi i/lub fizycznymi. Współczesna diagnostyka u noworodków zespołu FASD opiera się najczęściej...
-
Prognozowanie wpływu drgań komunikacyjnych na budynki mieszkalne za pomocą sztucznych sieci neuronowych i maszyn wektorów wspierających
PublikacjaDrgania komunikacyjne mogą stanowić duże obciążenie eksploatacyjne budynku, powodując zarysowania i spękania tynków, odpadanie wypraw, zarysowania konstrukcji, pękanie elementów konstrukcji lub nawet zawalenie się budynku. Pomiary drgań na rzeczywistych konstrukcjach są pracochłonne i kosztowne, a co ważne nie w każdym przypadku są one uzasadnione. Celem pracy jest analiza autorskiego algorytmu, dzięki któremu z dużym prawdopodobieństwem...
-
Możliwości sterowania mocą bierną elektrowni wiatrowej : Reactive power control methods in wind parks
PublikacjaReferat poświęcony jest zagadnieniu sterowania mocą bierną w elektrowniach wiatrowych. W pierwszej części referatu opisano tło problemu sterowania mocą bierną w parkach wiatrowych, podano powody, dla których moc bierna powinna podlegać regulacji oraz zarysowano metody, które mogą być do niej użyte. W celu sprawdzenia proponowanych metod kompensacji, zbudowano model matematyczny elektrowni wiatrowej, którego poszczególne elementy...
-
Experimental and theoretical studies on the photodegradation of 2-ethylhexyl 4-methoxycinnamate in the presence of reactive oxygen and chlorine species
Publikacja2-Ethylhexyl 4-methoxycinnamate (EHMC) is one of the most commonly used sunscreen ingredient. In this study we investigated photodegradation of EHMC in the presence of such common oxidizing and chlorinating systems as H2O2, H2O2/HCl, H2O2/UV, and H2O2/HCl/UV. Reaction products were detected by gas chromatography with a mass spectrometric detector (GC-MS). As a result of experimental studies chloro-substituted 4-methoxycinnamic...
-
Using human behavior to develop knowledge-based virtual organisations
PublikacjaPropozycja modelu opartego na zachowaniach ludzkich dla potrzeb budowy wirtuanych organizacji opartych na wiedzy.Virtual organizations promote dynamic interaction between individuals, groups, and organizations, who share their capabilities and resources to pursue a common goal and maximize their benefits. Among these resources, knowledge is a critical one that requires special attention in order to support problem-solving activities...
-
Optimal Placement of Phasor Measurement Unit in Power System using Meta-Heuristic Algorithms
PublikacjaThe phasor measurement units (PMUs) play an important and vital role in power system monitoring and controlling, since they provide the power system phasors stamped with a common real time reference through a global positioning system (GPS). Indeed, from economical point of view it is not possible to set PMUs in all system buses due to the high cost and the requirement of more complex communication...
-
Rospuda - czy wszędzie budować mosty?
PublikacjaStreszczenie - SummaryThe article presents the problem of planning transport system in the areas of high natural and landscape values. Bridges and roads crossing valuable areas undergo Environmental Impact Assessment (EIA) Procedure. This procedure in Poland is often treated only as formal requirement, not as an instrument helping to solve conflicts and to minimise negative environmental and landscape effects. The potential of...
-
Multivariate analysis of impedance data obtained for coating systems of varying thickness applied on steel
PublikacjaElectrochemical impedance spectroscopy (EIS) has proven to be a valuable test method for the electrochemical characterization of protective coatings on metals. The common way of analysis in impedance spectroscopy is to model the impedance spectrum by means of an equivalent circuit and to extract the quantity of interest using optimization techniques. A model, corresponding to the behavior of the sample under testing, is important...
-
Simultaneous determination of individual isothiocyanates in plant samples by HPLC-DAD-MS following SPE and derivatization with N-acetyl-l-cysteine
PublikacjaThe procedure for the isothiocyanates (ITCs) determination that involves derivatization with N-acetyl-l-cysteine (NAC) and separation by HPLC was developed. Prior to derivatization, plant ITCs were isolated and purified using solid-phase extraction (SPE). The optimum conditions of derivatization are: 500 μL of isopropanolic eluate obtained by SPE combined with 500 μL of derivatizing reagent (0.2 M NAC and 0.2 M NaHCO3 in water)...
-
WYBRANE WŁAŚCIWOŚCI FIZYCZNO-CHEMICZNE MIKROSFER I MOŻLIWOŚĆ ICH WYKORZYSTANIA W KOMPOZYTACH CEMENTOWYCH : The selected physico-chemical properties of microspheres and possibility of their use in cement composites
PublikacjaMicrospheres are formed during the mineral transformation stage in coal combustion. Their content in fly ashes from the combustion of different types of coals varies over a rather wide range from 0.01 to 4.8 wt.%. The microspheres have three main elements, silicon, aluminum and iron, the oxides of which account for about 89.0 wt.% of the material. Mineralogical analysis using XRD shows that microspheres mainly contain mullite and...
-
Dynamic GNSS Mission Planning Using DTM for Precise Navigation of Autonomous Vehicles
PublikacjaNowadays, the most widely used method for estimating location of autonomous vehicles in real time is the use of Global Navigation Satellite Systems (GNSS). However, positioning in urban environments using GNSS is hampered by poor satellite geometry due to signal obstruction created by both man-made and natural features of the urban environment. The presence of obstacles is the reason for the decreased number of observed satellites...
-
The effect of tire aging on acoustic performance of CPX reference tires
PublikacjaReduction of tire/road noise is one of the biggest environmental challenges of road traffic. To reduce that noise it is necessary to perform acoustic measurements on the base of wellproven standard procedures. One method of measurements that is in common use, namely the Close Proximity Method (CPX), is described in standard ISO-DIS 11819-2. As this method is used to classify road surfaces regarding their influence on vehicle noise,...
-
How to provide fair service for V2I communications in VANETs?
PublikacjaIn this paper, we focus on fairness issues of Vehicle-to-Infrastructure (V2I) communications. In particular, we show that under a common technique of selection of RSUs by OBUs based on the received signal strength, a vast variability of a number of OBUs connected to RSUs can be observed leading to inefficient/unfair service provided by RSUs. To overcome this problem, we propose an algorithm for RSU selection called RSEL to obtain...
-
Application of multicriteria decision analysis in solvent type optimization for chlorophenols determination with a dispersive liquid–liquid microextraction
PublikacjaThis study presents a novel support tool for the optimization and development of analytical methods. The tool is based on multi-criteria decision analysis (MCDA), namely the Technique for Order of Preference by Similarity to the Ideal Solution (TOPSIS), that allows users to rank possible solutions according to their requirements. In this study, we performed rankings of pairs of eight extraction and three dispersive solvents used...
-
From hobbies, straightforward analysis to serious research – the road to phd degree
PublikacjaThe illustration of the main articles goal is an example of author's academic career course, the aim of which is to obtain a doctoral degree in the field of geodesy and cartography. Today, the most important thing for the young scientist is the devotion to research in certain field of science, which is interested for the large community of scientists. From a psychological point of view, a unity of interest and experiments must...
-
Cyanogenic Compounds and Estrogen Disruptors
PublikacjaBalanced diet consists largely of plants containing cyanogenic compounds in the form of the more common cyanogenic glycosides and sometimes lipids. Maize, wheat, rye, apples, barley, oats, sugar cane and yet many other plants consumed by humans contain cyanogenic compounds. However the risk of poisoning is negligible as it is very easy to remove the toxic HCN by grinding and drying in air or soaking in water and an additional...
-
In-Situ Processing of Biocomposites via Reactive Extrusion
PublikacjaLaw regulations, economic and environmental factors are the main causes for the rapidly growing interests in biocomposites’ research, conducted currently in a number of academic and industrial scientific centers. However, weak polymer matrix/filler interactions, common in biocomposites, result in unsatisfactory mechanical properties, which limit their practical applications. From many attempts performed to solve this problem, in-situ...
-
Development and validation of an LC–MS/MS method for the determination of biogenic amines in wines and beers
PublikacjaBiogenic amines are group of organic, basic, nitrogenous compounds that naturally occur in plant, microorganism, and animal organisms. Biogenic amines are mainly produced through decarboxylation of amino acids. They are formed during manufacturing of some kind of food and beverages such as cheese, wine, or beer. Histamine, cadaverine, agmatine, tyramine, putrescine, and b-phenylethylamine are the most common biogenic amines found...
-
Agile Requirements Prioritization in Practice: Results of an Industrial Survey
PublikacjaAgile software development stresses the importance of providing the customer with a product of a maximized business value. To achieve that, requirements prioritization is used. Agile development methods like Scrum define guidelines for prioritization, however practitioners do not necessarily have to follow them. Our goal was to investigate the industry practice related to requirements prioritization process, including its timing,...
-
Analysis of ultimate compressive strength of cracked plates with the use of DOE techniques
PublikacjaThe objective of this work is to investigate the structural compressive response of plates with locked cracks accounting for all relevant factors and correlation between them. The nonlinear FE model considering both geometric and material nonlinearities is employed herein, and the FE model of the structural response of intact plates is validated with the available experimental data. In the common studies, based on One Factor at...
-
Risk of power cables insulation failure due to the thermal effect of solar radiation
PublikacjaLow-voltage, as well as high-voltage power cable lines, are usually buried in the ground. The ampacity of the power cables in the ground mainly depends on the thermal resistivity of the soil, which may vary in a wide range. A common practice in power cable systems performance is to supply them from a pole of an overhead line. If so, a section of the line is located in free air and can be directly exposed to solar radiation. In...
-
Toxoplasma gondii Recombinant Antigens in the Serodiagnosis of Toxoplasmosis in Domestic and Farm Animals
PublikacjaToxoplasmosis is caused by an intracellular protozoan, Toxoplasma gondii, and is a parasitic disease that occurs in all warm-blooded animals, including humans. Toxoplasmosis is one of the most common parasitic diseases of animals and results in reproductive losses. Toxoplasmosis in humans is usually caused by eating raw or undercooked meat or consuming dairy products containing the parasite. Diagnosis of toxoplasmosis is currently...
-
Ancient settlements-atavistic solutions for present water supply and drainage problems engendered by urbanism
PublikacjaWater is the most valuable resource available on earth. Although it is present in abundance, its usable volume is very scarce. This is the reason behind the existence of both floods and droughts around the world. However, human settlements face water scarcity issues that are primarily engendered by improper town planning measures. To create a balance between the available fractions of water, it is therefore imperative to have proper...
-
Enhancement of PUR/PIR foam thermal stability after addition of Zostera marina biomass component investigated via thermal analysis and isoconversional kinetics
PublikacjaIn the present work, a thorough thermogravimetric (TG) analysis of bio-based polyurethane–polyisocyanurate (PUR–PIR) foams in both nitrogen and oxygen atmosphere is performed. A sustainable element of the foam is a biopolyol obtained via acid-catalyzed liquefaction of Zostera marina and Enteromorpha Algae biomass. Based on isoconversional analysis and apparent activation energies, several conclusions are obtained. In contradiction...
-
Non-volatile molecular composition and discrimination of single grape white of chardonnay, riesling, sauvignon blanc and silvaner using untargeted GC–MS analysis
PublikacjaThis study developed and applied a GC–MS method aiming at molecular fingerprinting of 120 commercial single grape white wines (Chardonnay, Riesling, Sauvignon Blanc and Silvaner) for possible authentication according to grape variety. The method allowed detection of 372 peaks and tentative identification of 146 metabolites including alcohols, organic acids, esters, amino acids and sugars. The grape variety effect explained 8.3%...
-
Degradation of implantable materials – in vivo and in vitro research
PublikacjaThe article concerns the biological and electrochemical degradation of metallic implants in vivo and in vitro studies. The in vivo research dealt with degradation of plates used to join bones, as well as endoprostheses. The most common damages were: metalosis, breaking in the microstructure changes, breaking in area of holes, as well as plastic deformation throughout the length of an implant. The material used for the research...
-
Advances in olfaction-inspired biomaterials applied to bioelectronic noses
PublikacjaAmong all the senses, olfactory system of mammals is the least characterised as far as the mechanisms of odour identification are concerned. The results of recent investigations allow better understanding of the operation mechanism of the sense of smell. Progress in this field is crucial for the development of sensor technology based on olfaction-inspired biomaterials, which simulate the olfactory system of the biological counterparts....
-
Comparison analysis of selected nuclear power plants supplied with helium from high-temperature gas-cooled reactor
PublikacjaThe article presents results of efficiency calculations for two 560 MW nuclear cycles with high-temperature gas-cooled reactor (HTGR). An assumption was made that systems of this type can be used in so-called marine nuclear power plants. The first analysed system is the nuclear steam power plant. For the steam cycle, the efficiency calculations were performed with the code DIAGAR, which is dedicated for analysing this type of systems....
-
The application of environmental issues in designing urban structures – a framework for comprehensive local planning policies
PublikacjaThe implementation of environmental issues in planning and designing urban structures is becoming a novel approach and a common practice consistent with the paradigm of sustainable development. Maintaining environmental quality in urban areas, managing natural resources and understanding the complexity of urban systems is becoming increasingly challenging. Therefore, it is important to develop strategies for the integration of...
-
Comparison of the Efficiency of Hetero- and Homogeneous Catalysts in Cellulose Liquefaction
PublikacjaBiomass liquefaction is a well-known and extensively described process. Hydrothermal processes are well understood and can be used in the fuel industry. The use of organic solvents can result in full-fledged products for use in the synthesis of polyurethanes. The plastics industry, including polyurethanes, is targeting new, more environmentally friendly solutions. One of these is the replacement of petrochemical polyols with compounds...
-
Carbon nitride exfoliation for photocatalysis and photocatalytic ozonation over emerging contaminants abatement
PublikacjaThe production of graphitic carbon nitride was studied with the addition of a following exfoliation step using ultrasounds, at different times. The treatment produced catalysts with much higher surface areas, from 2.18 m2 g 1 with no treatment to 28.34 m2 g 1 after 36 h of exfoliation. During exfoliation, melem was also produced, and may further enhance the photoluminescence and photocatalytic properties. The photocatalytic reaction...
-
Things You Might Not Know about the k-Nearest Neighbors Algorithm
PublikacjaRecommender Systems aim at suggesting potentially interesting items to a user. The most common kind of Recommender Systems is Collaborative Filtering which follows an intuition that users who liked the same things in the past, are more likely to be interested in the same things in the future. One of Collaborative Filtering methods is the k Nearest Neighbors algorithm which finds k users who are the most similar to an active user...
-
Communication and Documentation Practices in Agile Requirements Engineering: A Survey in Polish Software Industry
PublikacjaRequirements engineering, system analysis and other analytical activities form the basis of every IT project. Such activities are not clearly defined in Agile development methods, but it does not mean that they are absent in an agile project. The aim of our work was to determine which practices related to requirements-related communication and which requirements documenting techniques are used in agile software projects. For this...
-
Global Complex Roots and Poles Finding Algorithm in C × R Domain
PublikacjaAn algorithm to find the roots and poles of a complex function depending on two arguments (one complex and one real) is proposed. Such problems are common in many fields of science for instance in electromagnetism, acoustics, stability analyses, spectroscopy, optics, and elementary particle physics. The proposed technique belongs to the class of global algorithms, gives a full picture of solutions in a fixed region ⊂ C × R and...
-
Review of the determination of modern used pesticides in water samples
PublikacjaThe increasingly widespread application of pesticides causes that larger amounts of them are entering the environment. Their presence in sources of drinking water, essential to life, is a particular danger. For these reasons it is important to monitor and analyse pesticide residues in the environment. The analysis of environmental samples for the presence of pesticides is very difficult. Firstly, the processes involved in sample...
-
Earthquake-induced pounding between asymmetric steel buildings
PublikacjaEarthquake-induced pounding between buildings has been the subject of numerous numerical and experimental studies in the resent years. The phe-nomenon may cause severe damage to structural elements as well as may also lead to the total collapse of colliding structures. A major reason leading to pounding between adjacent, insufficiently separated buildings results from the differences in their dynamic properties. The aim of this...
-
Mass spectrometric identification of 13C-Labeled metaboloites during anaerobic propanoic acid oxidation
PublikacjaBiowaste digestion is a possibility to gain biogas as a renewable fuel source. However, the anaerobic food chain may be disrupted by, e.g., substrate overload or by inhibitors, leading to the accumulation of volatile fatty acids (VFAs), predominantly of propanoic acid (PA). VFA Accumulation may cause a rapid pH decrease, less biogas production, or even a total inhibition. To maintain high biogas productivity or to prevent a collapse...