Filtry
wszystkich: 4522
-
Katalog
- Publikacje 3301 wyników po odfiltrowaniu
- Czasopisma 12 wyników po odfiltrowaniu
- Wydawnictwa 1 wyników po odfiltrowaniu
- Osoby 37 wyników po odfiltrowaniu
- Wynalazki 14 wyników po odfiltrowaniu
- Projekty 4 wyników po odfiltrowaniu
- Laboratoria 3 wyników po odfiltrowaniu
- Zespoły Badawcze 1 wyników po odfiltrowaniu
- Aparatura Badawcza 3 wyników po odfiltrowaniu
- Kursy Online 16 wyników po odfiltrowaniu
- Wydarzenia 1 wyników po odfiltrowaniu
- Dane Badawcze 1129 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: temperature%20modulation
-
Influence of electropolymerization temperature on corrosion, morphological and electrical properties of PPy doped with salicylate on iron
PublikacjaIn this work, the influence of the electropolymerization temperature on corrosion, morphological and electrical properties of polypyrrole (PPy) film is studied. Polypyrrole is electrochemically synthesized on iron in the presence of sodium salicylate. The X-ray diffraction and scanning electron microscopy are performed in order to study the structure and morphology of electrodeposited PPy. The electroactive surface area, corrosion...
-
MEASUREMENT OF TEMPERATURE-DEPENDENT VISCOSITY AND THERMAL CONDUCTIVITY OF ALUMINA AND TITANIA THERMAL OIL NANOFLUIDS
PublikacjaIn this study results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil is selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from...
-
Identification of Bodner-Partom Viscoplastic Model Parameters for Some Aluminum Alloys at Elevated Temperature
PublikacjaThe paper presents the identification process of inelastic (viscoplastic) properties for two aluminum alloys at a temperature of 120°C. The material parameters are calculated on the basis of uniaxial tension tests. Twelve tests at elevated temperature for each alloy have been performed—three tests for four different strain rates. The main purpose of the paper is to identify the Bodner-Partom viscoplastic model parameters for two...
-
A new viscoelastic method of calculation of low-temperature thermal stresses in asphalt layers of pavements
PublikacjaThe paper presents a new method of calculation of thermal stresses in asphalt layers of pavements induced by cooling or heating. The method, developed by the author, is based on the analytical solution for the linear viscoelastic Burgers model extended numerically for the case of asphalt layers whose rheological parameters are strongly dependent on temperature. The coefficient of thermal expansion and Poisson’s ratio may optionally...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublikacjaThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Mechanism of Reduced Sintering Temperature of Al2O3–ZrO2 Nanocomposites Obtained by Microwave Hydrothermal Synthesis
PublikacjaA novel method to obtain Al2O3–ZrO2 nanocomposites is presented. It consists of the co-precipitation step of boehmite (AlO(OH)) and ZrO2, followed by microwave hydrothermal treatment at 270 ◦ C and 60 MPa, and by calcination at 600 ◦ C. Using this method, we obtained two nanocomposites: Al2O3–20 wt % ZrO2 and Al2O3–40 wt % ZrO2. Nanocomposites were characterized by Fourier transformed infrared spectroscopy, Raman spectroscopy,...
-
High-temperature heat pumps – new devices for heat recovery and production of technological steam
PublikacjaIn the paper, the original high temperature compressor based heat pump with a dry working fluid, i.e. the one in which the slope of saturated vapour line is positive, was presented. The objective of the paper is to investigate the possibility of preparation of technological steam with tempperature 120 C from the waste heat resource at temperature of 50 C. Single comppression cycles as well as cascade systems have been considered...
-
The hydration of selected biologically relevant molecules – the temperature effect on apparent molar volume and compression
PublikacjaThe densities and sound velocities at T = (288.15, 293.15, 298.15, 303.15 and 308.15) K were measured for aqueous solutions of glycine, trimethylamine-N-oxide, taurine and N-methylacetamide. From these data, the apparent molar volumes, V the apparent molar isentropic compressions, KS,, and the Passynski hydration numbers of solutes were determined. The concentration dependencies of the calculated quantities, their limiting values...
-
Analytical method for calculation of heat source temperature drop for the Organic Rankine Cycle application
PublikacjaIn the paper presented are considerations on the cooperation of the limited capacity heat source with the Organic Rankine Cycle unit. Usually the heat source providing thermal energy to the Organic Rankine Cycle (ORC) may have twofold characteristics. It can be in the form of a single phase fluid, i.e. as hot exhaust gas or hot liquid, or in some cases it may be available as a phase changing fluid, as for example, technological...
-
Diagnostic tolerances' evaluation method of the start-up exhaust temperature of a naval gas turbine
PublikacjaThe conducted investigations aimed to elaborate the method of marking diagnostic tolerances of the exhaust temperature of a gas turbine observed during engine's start-up process. The diagnostic tolerances were determined by means of statistical inference by creating the hypothesis about a normal distribution of the start-up exhaust temperature's dispersion in the initial operation moment, which was subsequently verified applying...
-
The effect of calcination temperature on structure and photocatalytic properties of Au/Pd nanoparticles supported on TiO2
PublikacjaBimetallic nanoparticles, composed of two different metal elements, can exhibit peculiar electronic, optical, and catalytic or photocatalytic properties that are absent in the corresponding monometallic nanoparticles. We show the effect of calcination temperature (from 350 to 700°C) on the structure and the photocatalytic properties of Au/Pd-modified TiO2. The composition of the bimetallic Au/Pd nanoparticles in relation to their...
-
Measurement of temperature-dependent viscosity and thermal conductivity of alumina and titania thermal oil nanofluids
PublikacjaThe results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil was selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from 20°C to...
-
Influence of high temperature air-steam mixture application on time wood drying process
PublikacjaThe results of influence gas-steam mixture drying process on time wood drying process are presented. Wood species, namely oak (Quercus L.), beech (Fagus L.), pine (Pinus L.) and spruce (Picea K.) from the northern part of Pomerania region in Poland, were subject of air-steam mixture drying process. Main focus of those tests was to shorten the time of drying process and afterward to check properties of wood.
-
Theoretical examination of the fracture behavior of BC3 polycrystalline nanosheets: Effect of crack size and temperature
Publikacja2D carbon graphene nanostructures are elements of advanced materials and systems. This theoretical survey provides explanation to the mechanical and fracture behavior of mono- and polycrystalline BC3 nanosheets (denoted as MC- and PCBC3NS, respectively) as a function of temperature and the type of crack defects. The mechanical performance of PCBC3NS at elevated temperatures was monitored varying the number of grain boundaries (the...
-
Optical-Fiber Microsphere-Based Temperature Sensors with ZnO ALD Coating—Comparative Study
PublikacjaThis study presents the microsphere-based fiber-optic sensor with the ZnO Atomic Layer Deposition coating thickness of 100 nm and 200 nm for temperature measurements. Metrological properties of the sensor were investigated over the temperature range from 100 °C to 300 °C, with a 10 °C step. The interferometric signal was used to monitor the integrity of the microsphere and its attachment to the connecting fiber. For the sensor...
-
Multimodal analysis of traction forces and the temperature dynamics of living cells with a diamond-embedded substrate
PublikacjaCells and tissues are constantly exposed to chemical and physical signals that regulate physiological and pathological processes. This study explores the integration of two biophysical methods: traction force microscopy (TFM) and optically detected magnetic resonance (ODMR) to concurrently assess cellular traction forces and the local relative temperature. We present a novel elastic substrate with embedded nitrogen-vacancy microdiamonds...
-
Circumferential temperature distribution during pool boiling of R 141b onhorizontal modified tubes.
PublikacjaZaproponowano własną bierną, metodę intensyfikacji przejmowania ciepła w obszarze górnej tworzącej rurki w celu zminimalizowania obwodowego rozkładu temperatury. Metoda polega na naniesieniu aluminiowej warstwy porowatej tylko na części powierzchni rurki - właśnie w obszarze górnej tworzącej.
-
High-temperature heat pumps – potential technology for heat recovery and production of process heat
PublikacjaIn the paper, the high temperature vapour compressor based heat pump with a selection of working fluids, both perspective and ecological ones, is considered. Such system is not yet commercially available on the market and in author’s opinion it has significant potential for various applications. In the presented analysis it was assumed that the heat source has a temperature of 50oC and the temperature lift is 60, 80 and 100K respectively....
-
Parameters’ Identification of Perzyna and Chaboche Viscoplastic Models for Aluminum Alloy at Temperature of 120◦C
PublikacjaThe main purpose of this paper is the parameters identification of the Perzyna and the Chaboche models for the aluminum alloy at elevated temperature. The additional purpose is comparison of the results for these viscoplastic models. The results have been verified by the numerical simulation of the laboratory tests. The material parameters have been calculated on the basis of the uniaxial tension test. The determination of the...
-
Modeling of low calorific gas burning in a deficient oxygen environment and high-temperature oxidizer
PublikacjaThe experimental research will be performed using the experimental facility with a combustion chamber. The oxygen concentration in combustion oxidizers will be varied from 21% by volume (normal) air to 2%. The test combustion chamber will be fed with propane or methane as the reference fuel, then with low calorific fuels as test gases obtained by mixing various combustible components, e.g. H2, CH4, CO, and neutral gases, e.g. N2,...
-
Inverse determination of sliding surface temperature based on measurements by thermocouples with account of their thermal inertia
PublikacjaThis study developed an inverse heat conduction algorithm to determine temperature at a sliding surface taking account of thermocouple thermal inertia. The direct heat conduction problem was solved analytically based on the Laplace integral transform approach. The inverse algorithm was applied to the problem of friction of a brake material against a steel. The experiments were conducted on a pin-on-disc tribometer for three short-time...
-
Challenges in operating and testing loop heat pipes in 500–700 K temperature ranges
PublikacjaThe potential applications of loop heat pipes (LHPs) are the nuclear power space systems, fuel cell thermal management systems, waste heat recovery systems, medium temperature electronic systems, medium temperature military systems, among others. Such applications usually operate in temperature ranges between 500–700 K, hence it is necessary to develop an LHP system that will meet this requirement. Such a thermal management device...
-
Influence of Heat Treatment Temperature on Fatigue Toughness in Medium-Carbon High-Strength Steels
PublikacjaCurrent research has demonstrated that the tempering temperature affects the martensitic transformation of medium-carbon high-strength steels. This temperature plays an important role in the final microstructure, percentage ratios of martensite to ferrite phases and, consequently, in the mechanical properties and the fatigue response. So far, the relationship between the martensitic tempering temperature and the cyclic deformation...
-
Numerical Investigation of Nuclear Reactor Kinetic and Heat Transfer Fractional Model with Temperature Feedback
PublikacjaAbstract—In the paper, the numerical results concerning the kinetics and proposed heat exchange models in nuclear reactor based on fractional calculus are presented for typical inputs. Two fractional models are proposed and compared with the model based on ordinary derivative. The first fractional model is based on one of the generalized Cattaneo equations. The second one is based on replacing the ordinary to fractional order of...
-
The influence of solution annealing temperature on the properties of Lean Duplex 2101 welded joints in tubes
PublikacjaThe article presents a technology of TIG longitudinal welding without filler material (142) of heat exchanger tubes made of Lean Duplex 2101. The results of studies on the effect of heat treatment (solution annealing) on tensile strength, plasticity, delta ferrite and the structure of smooth tubes are shown. It was found, that the change in solution annealing temperature across the tested range has an impact on mechanical properties...
-
Effect of austempering temperature on microstructure and cyclic deformation behaviour of multiphase low-carbon steel
PublikacjaThis paper examined the cyclic deformation behaviour of multiphase low-carbon steel that was subjected to austempering heat treatments at four temperatures (190 °C, 230 °C, 275 °C, and 315 °C) below the martensite start temperature (Ms = 353 °C). The tests were conducted at room temperature, under fully reversed strain-controlled conditions, with strain amplitudes in the range 0.5–1.0%. The microstructure was observed by transmission...
-
High temperature air/steam gasification of biomass in view of hydrogen rich gas production.
PublikacjaArtykuł przedstawia opis nowej i zaawansowanej metody konwersji termochemicznej biomasy i miejskich odpadów stałych w paliwo gazowe, bogate w wodór. W porównaniu z tradycyjnym procesem gazyfikacji, w metodzie tej wykorzystuje się powietrze/parę wodną przegrzane do wysokiej temperatury (powyżej 1300 st. C). Przegrzanie powietrza lub pary wodnej odbywa się z zastosowaniem ceramicznego przegrzewacza wysokotemperaturowego. W celu...
-
Hydrogen rich gas production from high temperature air/steam gasification of biomass
PublikacjaW pracy przedstawiono nowoczesną technikę konwersji biomasy oraz stałych odpadów komunalnych w celu produkcji paliwa gazowego bogatego w wodór. Opisany proces gazyfikacji przebiega w wysokiej temperaturze przy obniżonej koncentracji tlenu i udziale pary wodnej. Dzięki temu możliwa jest produkcja gazów palnych, w szczególności H2, który można wykorzystać do produkcji energii elektrycznej i cieplnej.
-
(Vapour and liquid) equilibrium in (N,N-dimethylacetamide+methanol+water) at the temperature 313.15 K.
PublikacjaPraca zawiera wyniki pomiarów całkowitej prężności pary dla tytułowego układu trójskładnikowego oraz dla ''składowych'' układów binarnych. Wyniki obliczeń nadmiarowej energii swobodnej mieszania dla układów (N,N-dimetyloaceta-mid+woda) i (N,N-dimetyloacetamid+metanol) porównane zostały z rezultatami uzyskanymi wcześniej dla innych układów (amid+metanol) oraz (amid+woda). Znaleziono interesującą zależność wartości nadmiaru...
-
Wpływ sezonowych zmian temperatury na właściwości sedymentacyjne osadu czynnego
PublikacjaPrzedstawiono badania dotyczące wpływu temperatury na właściwości sedymentacyjne osadu czynnego w dwóch komunalnych oczyszczalniach ścieków. Sezonowe zmiany opadalności osadu związane są ze zmianami temperatury oraz zmianą składu populacji bakterii osadu czynnego (bakterie nitkowate). Na rozwój tych bakterii wpływa nie tylko temperatura, lecz także intensywność napowietrzania oraz dostępność substancji pożywkowych.
-
Evaluation of porous 430L stainless steel for SOFC operation at intermediate temperatures
PublikacjaW pracy przedstawiono badania porowatej stali nierdzewnej typu 430L do zastosowań w tlenkowych ogniwach paliwowych jako podłoża. Podłoża były poddawane utlenianiu w powietrzu oraz w wodorze i analizowane z wykorzystaniem mikroskopu elektronowego, dyfrakcji rentgenowskiej i termograwimetrii cyklicznej.
-
Theoretical prediction of enthalpies and temperatures of sublimation of organochlorine compounds including pesticides
Publikacja -
Temperatura ekwiwalentna jako wskaźnik do oceny odczuć środowiska cieplnego
Publikacja -
Numeryczny sposób określenia temperatury czynnika chłodniczego po procesie sprężenia
PublikacjaTemperatura czynnika chłodniczego po sprężeniu jest istotna wielkością w pracy układu chłodniczego. Określa ona maksymalna wartość ciśnienia możliwą do uzyskania na jednym stopniu sprężania. Ponadto określa typy możliwych do wykorzystania sprężarek, a także konieczność ich chłodzenia. Podczas prac nad symulacjami układów chłodniczych niezbędny jest sposób jej wyliczenia. W pracy zaprezentowano autorską metodę określenia temperatury...
-
Przegląd metod pomiaru temperatury przewodów linii napowietrznych wysokiego napięcia
PublikacjaW artykule przedstawiono przegląd metod pomiaru temperatury napowietrznych linii wysokiego napięcia stosowanych w celu poprawy niezawodności eksploatacji i w celu wyznaczania dopuszczalnej obciążalności linii. Omówiono system DOL dynamicznej obciążalności linii oraz bezdotykowe metody pomiaru temperatury: pomiar z użyciem pasywnych czujników SAW (ang. Surface acoustic wave sensor), DTS (distributed temperature sensing) z wykorzystaniem...
-
Modelling of Asphalt Mixes under Long Time Creep at Low Temperatures
PublikacjaProper description of asphalt mixtures behavior under long time load is one of the most important factors in analyses of strain and stress relations at low temperatures both from traffic and environmental loads. For example different models of thermal stress accumulation require different approaches of description of asphalt concrete. But in all cases it is required to describe its behavior under long time loading, which in some...
-
Wpływ temperatury na pomiary geodezyjne oraz odkształcenia wybranych budowli
PublikacjaW rozdziale omówiono wpływ temperatury na wyniki pomiarów geodezyjnych różnych budowli inżynierskich
-
Poprawa niezawodności silnika przez monitoring i zmniejszenie temperatury pracy
PublikacjaW artykule przedstawiono metody pomiaru temperatury izolacji silników oraz sposób wyznaczenia temperatury dopuszczalnej w danych warunkach otoczenia.
-
Wpływ temperatury warystorowych ograniczników przepięć ZnO na prąd upływowy
PublikacjaW artykule omówiono wyniki pomiarów charakterystyk prądowo – napięciowych w zakresie prądu upływowego warystorowych ograniczników przepięć z tlenku cynku ZnO dla temperatur w zakresie 263 K – 373 K. Badania wykonano w celu stwierdzenia powtarzalności charakterystyk ograniczników przepięć oraz obliczenia współczynników poprawkowych koniecznych dla przeliczania wyników pomiarów prądu upływowego na temperaturę odniesienia w celu porównywania...
-
Wpływ temperatury procesu na przemiany tłuszczu podczas głębokiego smażenia
PublikacjaBadano wpływ temperatury w zakresie 160 - 190 C na przemiany termooksydatywne tłuszczów smażalniczych. Miarą degradacji tłuszczu była zmiana jego lepkości. Stwierdzono, że wzrost temperatury i czasu smażenia powoduje wzrost lepkości tłuszczu. Szybkość tych zmian była różna dla różnych surowców tłuszczowych. Wyznaczono równania opisujące wzrost lepkości tłuszczów w funkcji czasu dla temperatur: 160, 175 i 190 C.
-
Assessment of reformer tubes degradation during longterm service at elevated temperatures
Publikacja -
Stanowisko do badania czujników temperatury w laboratorium metrologii przemysłowej
PublikacjaW Laboratorium Miernictwa Przemysłowego powstało stanowisko dydaktyczno-badawcze do badania czujników temperatury, wykorzystujące mierniki N12T firmy Lumel oraz szereg termoelektrycznych i rezystancyjnych czujników temperatury. Mierniki N12T można zdalnie programować jak również odbierać dane przez nie zarejestrowane. Do zdalnej transmisji wy-korzystywana jest magistrala szeregowa RS485 z użyciem protokołu MODBUS. Zastosowanie...
-
Określenie temperatury ekwiwalentnej do projektowania konstrukcji nawierzchni w Polsce
PublikacjaAnalityczne opracowanie wyjaśniające zasady weryfikacji i aktualizacji obliczeń zawartych w nowym katalogu typowych konstrukcji nawierzchni podatnych i półsztywnych z 2013 roku dostosowanym do współczesnych technologii i materiałów, zwiększonego obciążenia dróg przez ruch drogowy, zmienionych sposobów wzmacniania podłoża, recyklingu materiałów drogowych, ujednoliconego nazewnictwa warstw konstrukcji nawierzchni oraz nowych metod...
-
Wzrost temperatury cieczy roboczej jako symptom awarii układu hydraulicznego
PublikacjaW artykule opisano czynniki wpływające na nagły wzrost temperatury cieczy roboczej w układach hydraulicznych. Przedstawiono na podstawie przykładowego schematu hydraulicznego możliwe przyczyny wzrostu temperatury, oraz tok działań mających doprowadzić do szybkiej identyfikacji uszkodzonego elementu.
-
Achieving Efficient and Stable Deammonification at Low Temperatures—Experimental and Modeling Studies
PublikacjaThe short-term effects of temperature on deammonification sludge were evaluated in a laboratory-scale sequencing batch reactor (SBR). Mathematical modeling was used for further evaluations of different intermittent aeration strategies for achieving high and stable deammonification performance at decreasing temperatures. As for the biomass cultivated at high temperatures (e.g., 30 C), a higher temperature dependency (the adjusted...
-
Szacowanie estymaty menzurandu temperatury skóry człowieka podczas próby wysiłkowej
PublikacjaW artykule zaprezentowano wyniki pomiarów temperatury skóry człowieka podczas próby wysiłkowej. Ponieważ uzyskane wyniki nie podlegają rozkładowi normalnemu, wyznaczono wartości pięciu różnych estymatorów menzurandu. Otrzymane rezultaty wykazały, że w rozważanym przypadku najlepszy estymator menzurandu otrzymujemy z metody bootstrap, ponieważ charakteryzuje się on najmniejszym odchyleniem standardowym.
-
RESEARCH OF HYDRAULIC PISTON PUMPS’ START-UP IN LOW AMBIENT TEMPERATURES
PublikacjaStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of increase of resistance of cold oil flow in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump...
-
Konstrukcje z gruntu zbrojonego geosyntetykami odciążające przyczółki - Analiza temperatur
PublikacjaW artykule podjęto, bardzo istotny z punktu widzenia bezpieczeństwa i trwałości konstrukcji, temat zachowania się w czasie przyczółków mostowych, które zaprojektowano z wykorzystaniem konstrukcji odciążających z gruntu zbrojonego geosyntetykami. Na dwóch przykładach przeanalizowano zmienność temperatur wewnątrz bloku z gruntu zbrojonego. Temperatura w otoczeniu geozbrojenia syntetycznego może mieć istotny wpływ na jego trwałość.
-
Modulation of CYP3A4 activity and induction of apoptosis, necrosis and senescence by the anti-tumour imidazoacridinone C-1311 in human hepatoma cells
Publikacja -
Prediction of Stress and Deformation Caused by Magnetic Attraction Force in Modulation Elements in a Magnetically Geared Machine Using Subdomain Modeling
Publikacja