Wyniki wyszukiwania dla: I / V measurements
-
Polynomial Algorithm for Minimal (1,2)-Dominating Set in Networks
PublikacjaDominating sets find application in a variety of networks. A subset of nodes D is a (1,2)-dominating set in a graph G=(V,E) if every node not in D is adjacent to a node in D and is also at most a distance of 2 to another node from D. In networks, (1,2)-dominating sets have a higher fault tolerance and provide a higher reliability of services in case of failure. However, finding such the smallest set is NP-hard. In this paper, we...
-
Entropy of water calculated from harmonic approximation: estimation of the accuracy of method
PublikacjaSome molecular dynamics simulations were performed for liquid TIP4P and SPC water at a constant density (1.00 g/cm(3)) and within the temperature range of 5-90 degrees C. By using harmonic approximation, both the entropy of water S-H and the specific heat c(v) were calculated, and the results were compared to literature data. It was found that harmonic approximation overestimates absolute entropy of TIP4P water by 5.6 J/mol K (similar...
-
Bridge Ergonomic Design: A Review
PublikacjaHuman error remains the most common cause of marine incidents and it is worth emphasizing that navigator’s performance is directly affected by ergonomic factors on the bridge. Studies regarding influence of bridge design and work environment on the operator are rare, thus the main purpose of this paper is to fill in this gap. Documents issued by recognized organizations, research publications and additional sources were reviewed...
-
Ti-Fe2O3/In2O3 as photoactive material: The role of the substrate in photoelectrochemical water oxidation
PublikacjaThe layers of Ti-Fe2O3/In2O3 were prepared on the different substrates using hydrothermal method: Ti/TiO2 nanotubes, Ti foil, FTO and FTO/TiO2. Materials were characterized using scanning electron microscopy, XRD, Raman, UV-Vis, and X-ray photoelectron spectroscopy and tested as photoanodes for water oxidation under illumination. The formation of heterojunction on the TiO2 nanotubes increases photocurrent of water oxidation at...
-
Exfoliated graphite with spinel oxide as an effective hybrid electrocatalyst for water splitting
PublikacjaThe aim of the conducted research was to develop hybrid nanostructures formed from MnCo2O4 and exfoliated graphite. Carbon added during the synthesis allowed for obtaining a well-distributed MnCo2O4 particle size with exposed active sites contributing to the increased electric conductivity. The influence of the weight ratios of carbon to a catalyst for hydrogen and oxygen evolution reactions was investigated. The new bifunctional...
-
A nine-input 1.25 mW, 34 ns CMOS analog median filter for image processing in real time
PublikacjaIn this paper an analog voltage-mode median filter, which operates on a 3 × 3 kernel is presented. The filter is implemented in a 0.35 μm CMOS technology. The proposed solution is based on voltage comparators and a bubble sort configuration. As a result, a fast (34 ns) time response with low power consumption (1.25 mW for 3.3 V) is achieved. The key advantage of the configuration is relatively high accuracy of signal processing,...
-
Dostrajanie obwodów rezonansowych w systemach bezprzewodowego zasilania sensorów medycznych
PublikacjaW artykule opisano odbiornik energii transmitowanej bezprzewodowo z automatycznym dostrajaniem obwodu rezonansowego, służący do zasilania miniaturowej kapsułki endoskopowej. Odbiornik jest wyposażony w układ zarządzania energią, który steruje automatycznym dostrajaniem obwodu rezonansowego oraz stabilizuje napięcie zasilania ustawiane w zakresie 1,2 – 1,8 V. Przeprowadzone pomiary prototypowego układu scalonego, wykonanego w technologii...
-
Evaluation of Selected Innovation Policy Instruments on the Example of Poland
PublikacjaThe main purpose of the paper is to analyze and evaluate the selected instruments of innovation policy in Poland: cooperative relations, business environment institutions and innovation centers, supported within Priority Axis V of OP IE 2007-2013. The evaluation was made on the basis of the four criteria: complementarity, adapting to the needs of businesses, the impact on the innovation and durability of the provided support. The...
-
Low speed permanent magnet synchronous generator for vertical axis wind turbine
PublikacjaThe paper presents design process and tests of a prototype low speed permanent magnet synchronous generator (PMSG) dedicated for the innovative vertical-axis wind turbine. The rated data of the designed generator are following: power - 15 kVA, voltage - 400 V (Y), rotation speed - 93.75 rpm. The design assumptions, chosen results of the design process and experimental tests of the prototype PMSG are presented. The considered PMSG...
-
Foreign Entry Modes of High-tech Firms in Poland
PublikacjaThe main objective of the article is to present the role and importance of foreign entry modes in internationalization process and their key determinants. Research methods: A quantitative research design was used. A survey was conducted on the sample of 263 firms operating in...
-
The effect of a belt position in the spindle driving system on critical rotational speeds
PublikacjaThe aim of this paper was to examine how the belt pulley position affects critical rotational speeds of the modernized spindle of the sliding table saw Fx3. Methodology of determination of critical rotational speeds of the spindle in a function of the spindle design features and its driving system is presented. Spindles in these kind of machine tools are mainly driven with V-belts, and the pulleys on the spindles might be positioned:...
-
Contamination of water in Oliwski Stream after the flood in 2016
PublikacjaIn the article pollution of stream waters with surface runoff from an urbanized area caused by an extremely high rainfall is discussed. The analyzes were carried out after the rainfall of the depth 152 mm which took place in Gdańsk on 14th and 15th July 2016. This extreme rainfall caused urban flooding, damage of several retention ponds and pollution of surface waters. In the article the results of physical and chemical analyzes...
-
A lower bound on the double outer-independent domination number of a tree
PublikacjaA vertex of a graph is said to dominate itself and all of its neighbors. A double outer-independent dominating set of a graph G is a set D of vertices of G such that every vertex of G is dominated by at least two vertices of D, and the set V(G)D is independent. The double outer-independent domination number of a graph G, denoted by gamma_d^{oi}(G), is the minimum cardinality of a double outer-independent dominating set of G. We...
-
Effects of UV light irradiation on fluctuation enhanced gas sensing by carbon nanotube networks
PublikacjaThe exceptionally large active surface-to-volume ratio of carbon nanotubes makes it an appealing candidate for gas sensing applications. Here, we studied the DC and low-frequency noise characteristics of a randomly oriented network of carbon nanotubes under NO2 gas atmosphere at two different wavelengths of the UV light-emitting diodes. The UV irradiation allowed to sense lower concentrations of NO2 (at least 1 ppm) compared to...
-
Structure and paramagnetism in weakly correlated Y8Co5
PublikacjaWe report the basic physical properties of monoclinic Y8Co5 determined by means of magnetic susceptibility, electrical resistivity, and specific heat measurements. The crystal structure of Y8Co5 is monoclinic (P21/c) with lattice parameters a = 7.0582(6) Å, b = 7.2894(6) Å, c = 24.2234(19) Å, and β = 102.112(6)° as refined by using synchrotron powder x-ray diffraction data. The compound shows temperature independent paramagnetism...
-
Pochodne amfoterycyny B z zawadą przestrzenną - nowa grupa antymykotyków o niskiej toksyczności i aktywnych względem szczepów z opornością wielolekową. Badanie natury i mechanizmów ich właściwości fizykochemicznych i biologicznych
PublikacjaBadania prezentowane w ramach niniejszej rozprawy koncentrują się na poznaniu i wyjaśnieniu molekularnych mechanizmów leżących u podstaw poprawy selektywnej toksyczności pochodnych amfoterycyny B z zawadą przestrzenną jak również ich aktywności względem opornych szczepów grzybowych. Kluczowe wnioski wynikające z pracy są następujące: i) mutanty drożdżaków z defektem biosyntezy ergosterolu zachowują wrażliwość na badane związki...
-
Nitrogen-Incorporated Boron-Doped Nanocrystalline Diamond Nanowires for Microplasma Illumination
PublikacjaThe origin of nitrogen-incorporated boron-doped nanocrystalline diamond (NB-NCD) nanowires as a function of substrate temperature (Ts) in H2/CH4/B2H6/N2 reactant gases is systematically addressed. Because of Ts, there is a drastic modification in the dimensional structure and microstructure and hence in the several properties of the NB-NCD films. The NB-NCD films grown at low Ts (400 °C) contain faceted diamond grains. The morphology...
-
Wstępna ocena wielkości stężeń związków azotu i fosforu odprowadzanych z wodami powierzchniowymi do Zatoki Puckiej z terenu gminy Puck
PublikacjaThe ferilizers used in agriculture negatively affect the surface and groundwater quality. The Bay of Puck is a semi-closed part of the Gulf of Gdańsk, which is particularly vulnerable to eutrophication caused by the inflow of nutrient substances. The Bay is surrounded by the lands intensively used in agriculture. Also a number of touristic resorts is located on its coast. The streams and rivers carry the load of nitrogen and phosphorus...
-
Hybrid electrode materials for fast performance devices
PublikacjaEnergy storage devices such as Electrochemical Double Layer Capacitors and other types of the electrochemical capacitors require chemically stable, non-soluble, electrochemically active electrode materials compatible with appropriate electrolytes. Factors which determine their applicability are derived from so called electrochemical window of electroltes, nature of charge accumulation and their kinetics. On the other hand technological...
-
Bridging challenges of clinical decision support systems with a semantic approach. A case study on breast cancer
PublikacjaThe integration of Clinical Decision Support Systems (CDSS) in nowadays clinical environments has not been fully achieved yet. Although numerous approaches and technologies have been proposed since 1960, there are still open gaps that need to be bridged. In this work we present advances from the established state of the art, overcoming some of the most notorious reported difficulties in: (i) automating CDSS, (ii) clinical workflow...
-
Biological properties of chitosan/Eudragit E 100 and chitosan/poly(4-vinylpyridine) coatings electrophoretically deposited on AgNPs-decorated titanium substrate
PublikacjaThe objective of the study was the determination of the response, in contact with human osteoblast-like MG-63 cells, of electrophoretically deposited coatings composed of chitosan (CS), Eudragit E 100 (EE100), or poly(4- vinylpyridine) (P4VP) on a silver nanoparticle (AgNPs)-decorated titanium substrate. Before deposition, the substrate was coated with silver by electro-reduction of silver nitrate. The coatings deposition was carried...
-
Case Study of Old Steel Riveted Railway Truss Bridge: From Material Characterization to Structural Analysis
PublikacjaThe structural analysis of an old steel riveted railway truss bridge located over the Maruska River on the Działdowo – Olsztyn, Poland railway line is performed in this paper to check its behaviour under today’s railway loads. The mechanical properties of construction steel extracted from the old steel bridge are investigated by tensile tests, impact tests through the Charpy pendulum impact V-notch, and an optical emission spectrometer....
-
The elasto-plastic numerical study of crack initiation in notched PMMA specimens under uniaxial loading conditions – Tension and torsion
PublikacjaThis paper presents the results of FEM numerical calculations aimed at describing the plastic strain and stress fields under critical loading conditions: tensile force or torsional moment. The calculations were carried out with reference to the results of experimental tensile and torsional tests of flat PMMA specimens weakened with V-notches of different root radii: 0.5, 2 and 10 mm. The procedure for conducting nonlinear numerical...
-
Ceramic composites for single-layer fuel cells
PublikacjaComposite materials consisting of acceptor doped lanthanum orthoniobate electrolyte phase (La0.98Ca0.02NbO4) and Li2O:NiO:ZnO semiconducting phase were synthesized. The precursor powder of La0.98Ca0.02NbO4 was prepared in nanocrystalline (mechanosynthesis) and microcrystalline (solid-state synthesis) form. The composite can be applied in a single-layer fuel cell, because of the presence of two phases acting as an anode and a cathode...
-
Influence of High Temperature Oxidation on Hydrogen Absorption and Degradation of Zircaloy-2 and Zr 700 Alloys
PublikacjaThe present research was aimed at determining the effects of the oxide layers on hydrogen absorption, microstructure and mechanical properties of the Zircaloy- 2 and Zr 702 alloys. The oxidation was made at 350 °C, 700 °C and 900 °C for 10 to 30 min in laboratory air, followed by hydrogen cathodic charging for 72 h and annealing at 400 °C for 4 h. The slow strain rate tests were carried out on oxidized, charged and annealed specimens. The...
-
Isolation and some properties of collagen from the backbone of Baltic cod(Gadus morhua)
PublikacjaOssein from Baltic cod backbone was obtained after extraction of non-collagenous protein with 0.1 M NaOH solution and demineralization with 1.0 M HCl solution. The extractions were performed at 4 C for24, 48 and 72 h using a solid/solution ratio from 1:4 to 1:8 (w/v). After 48 h of extraction in 0.5 M acetic acid only about 25% of collagen was dissolved. After 48 h of extraction at optimal concentration of pepsin(4 mg/g ossein)...
-
A 1-nS 1-V Sub-1-µW Linear CMOS OTA with Rail-to-Rail Input for Hz-Band Sensory Interfaces
PublikacjaThe paper presents an operational transconductance amplifier (OTA) with low transconductance (0.62–6.28 nS) and low power consumption (28–270 nW) for the low-frequency analog front-ends in biomedical sensor interfaces. The proposed OTA implements an innovative, highly linear voltage-to-current converter based on the channel-length-modulation effect, which can be rail-to-rail driven. At 1-V supply and 1-Vpp asymmetrical input driving,...
-
Evaluation of Immobilization of Selected Peat-Isolated Yeast Strains of the Species Candida albicans and Candida subhashii on the Surface of Artificial Support Materials Used for Biotrickling Filtration
PublikacjaThe paper describes the process of n-butanol abatement by unicellular fungi, able to deplete n-butanol content in gas, by using n-butanol as source of carbon. Isolated and identified fungi species Candida albicans and Candida subhashii were subjected to a viability process via assimilation of carbon from hydrophilic and hydrophobic compounds. The isolates, which exhibited the ability to assimilate carbon, were immobilized on four...
-
Performance Comparison of a 650 V GaN SSFET and CoolMOS
PublikacjaThe new technology of wide band gap semiconductors is said to outperform up-to-date silicon devices. High voltage Gallium Nitride (GaN) transistors, now emerging in the market, have even three times shorter switching times and even four times smaller energy losses compared to the best in-class Si devices. In this paper the performance of a 650 V GaN SSFET is evaluated and compared with the newest silicon family of CoolMOS™ technology....
-
Morphology control via dual solvent crystallization for high-mobility functionalized pentacene-blend thin film transistors
PublikacjaWe present an approach to improving the performance of solution processed organic semiconductor transistors based on a dual solvent system. We here apply this to a blend containing the π-conjugated small molecule 6,13 bis(triisopropylsilylethynyl) pentacene (TIPS-pentacene) and polystyrene, which acts as an inert binder. Using a semiconductor-binder solution of two solvents, where the main solvent is a better solvent of the small...
-
Graphene oxide, reduced graphene oxide and composite thin films NO2 sensing properties
PublikacjaA graphene oxide (GO), reduced graphene oxide (RGO) and poly(3,4-ethylenedioxytiophene)-reduced graphene oxide (PEDOT-RGO composite) gas sensors were successfully fabricated using an electrodeposition method. The electrodeposition was carried out in aqueous GO dispersions. To obtain RGO and PEDOT-RGO, the electrochemical reduction of GO and PEDOT-GO was carried out in 0.1 M KCl at a constant potential of −0.85 V. The GO, RGO and PEDOT-RGO...
-
Optimum Choice of Randomly Oriented Carbon Nanotube Networks for UV-Assisted Gas Sensing Applications
PublikacjaWe investigated the noise and photoresponse characteristics of various optical transparencies of nanotube networks to identify an optimal randomly oriented network of carbon nanotube (CNT)-based devices for UV-assisted gas sensing applications. Our investigation reveals that all of the studied devices demonstrate negative photoconductivity upon exposure to UV light. Our studies confirm the effect of UV irradiation on the electrical...
-
"Raport z wstępnych badań własności stali trudnościeralnej 460HB",. ang "Report on preliminary tests of the properties of wear-resistant steel 460HB"
PublikacjaMikrostrukturę badanej stali trudnościeralnej 460HB stanowi drobnoziarnisty martenzyt odpuszczony, który jest właściwy dla stali konstrukcyjnych niskowęglowych, niskostopowych ulepszonych cieplnie. W przypadku blach grubych, do których zalicza się badana stal, struktura może ulec zaburzeniu, jeżeli w hutniczym procesie wytwórczym wystąpiła niejednorodność odkształcenia plastycznego i w konsekwencji tworzenie się pasm segregacyjnych,...
-
Kompozytowy most dla pieszych. Badania doświadczalne i przygotowanie do projektowania
PublikacjaDysertacja powstała w ramach grantu badawczego NCBiR, pt. „Opracowanie kompozytowych przęseł mostów dla pieszych do zastosowania nad drogami GP”, nr PBS1/B2/6/2013. Głównym celem pracy było wsparcie procesu projektowania kompozytowego mostu pieszo-rowerowego. Zakres pracy obejmuje badania doświadczalne elementów kompozytowych GFRP, walidację modeli obliczeniowych oraz wykorzystanie aparatu analizy wrażliwości do procesu projektowego....
-
Determination of the Major By-Products of Citrus hystrix Peel and Their Characteristics in the Context of Utilization in the Industry
PublikacjaKaffir lime (Citrus hystrix) is a popular citrus in Southeast Asia. Despite the growing interest in the peel of the fruit, the leaves are the most frequently used part of the fruit. The aim of the study was to determine the main by-products of the peel, such as pectins, minerals, essential oil, and bioactive compounds, and to evaluate the possibility of using them in various branches of industry. In the study of the essential oil...
-
High-conducting Bi4V2-xFexO11-δ ceramics containing Fe2O3 nanocrystals: Structure and properties
PublikacjaThe topography, structure, thermal, magnetic, and electrical properties of Bi4V2-xFexO11-δ ceramics substituted with x = 0.5 and 0.7 Fe were studied. The microscope analysis showed the presence of iron-rich nanocrystals formed on the Bi-Fe-V-O grains. The X-ray diffraction studies confirmed that grains are built mostly of tetragonal Bi4V1.5Fe0.5O10.5 phase. Thermal properties analysis showed an order-disorder type γ ↔ γʹ phase...
-
Electrocatalytic oxidation of methanol, ethylene glycol and glycerine in alkaline media on TiO2 nanotubes decorated with AuCu nanoparticles for an application in fuel cells
PublikacjaIn this work, we present the catalytic and photocatalytic activity of AuCu nanostructures obtained on TiO2 nanotubes toward methanol, ethylene glycol and glycerine oxidation. The electrode material is prepared by anodization of Ti foil, thin AuCu layer sputtering and rapid thermal treatment under argon atmosphere. Scanning electron microscopy images confirmed the presence of ordered tubular architecture of TiO2 as well as nanoparticles...
-
The optimization of CuxO microwires synthesis for improvement in photoelectrochemical performance
PublikacjaOne of the most important challenges in the fabrication of CuxO microstructures via the electrochemical method is formation of long, regular and well-packed microwires with good adhesion on the Cu substrate and to achieve better photoelectrochemical properties, which can be potentially applied in solar-driven water splitting and CO2 conversion to light hydrocarbons. In this paper, Cu2O photoelectrode has been fabricated by direct...
-
A 0.5 V Nanowatt Biquadratic Low-Pass Filter with Tunable Quality Factor for Electronic Cochlea Applications
PublikacjaA novel implementation of an analogue low-power, second-order, low-pass filter with tunable quality factor (Q) is presented and discussed. The filter feature is a relatively simple, buffer-based, circuit network consisting of eleven transistors operating in a subthreshold region. Q tuning is accomplished by injecting direct current into a network node, which changes the output resistance of the transistors and, as a result, modifies...
-
The computational complexity of the backbone coloring problem for planar graphs with connected backbones
PublikacjaIn the paper we study the computational complexity of the backbone coloring problem for planar graphs with connected backbones. For every possible value of integer parameters λ≥2 and k≥1 we show that the following problem: Instance: A simple planar graph GG, its connected spanning subgraph (backbone) HH. Question: Is there a λ-backbone coloring c of G with backbone H such that maxc(V(G))≤k? is either NP-complete or polynomially...
-
Improvement of ships seakeeping performance by application of the full-scale cfd simulations
PublikacjaThe ship’s fuel economy is increasingly important. The paper presents the effect of redesigning a case study ship for increasing seakeeping performance. Selected wave parameters reflect very difficult operational conditions existing on the North Sea and the Baltic Sea. The analyzed variants of a case study ship represent the latest developments of modern hull forms. The concepts similar to V-shaped bulbous bow, X-bow, X-aft, B-bow...
-
Laser induced formation of copper species over TiO2 nanotubes towards enhanced water splitting performance
PublikacjaWe proposed fast and scalable route where the ordered TiO2 nanotubes coated with thin copper layers were annealed by the laser beam of 355 nm wavelength at different fluencies in the range of 15–120 mJ/cm2. As a result, copper species are integrated with the titania substrate and the formed material exhibits unique optical absorption bands in the visible range. Moreover, X-ray photoelectron spectroscopy analysis reveals the formation...
-
Graph security testing
PublikacjaSet S ⊂ V is called secure set iff ∀ X ⊂ S | N [ X ] ∩ S | ≥ | N ( X ) \ S | [3]. That means that every subset of a secure set has at least as many friends (neighbour vertices in S) as enemies (neighbour vertices outside S) and will be defended in case of attack. Problem of determining if given set is secure is co −NP -complete, there is no efficient algorithm solving it [3]. Property testers are algorithms that distinguish inputs...
-
Surface sediments pollution due to shipwreck s/s “Stuttgart”: a multidisciplinary approach
PublikacjaShipwrecks may pose a serious source of pollution for marine ecosystems. For this reason, it is of great importance to perform a marine ecosystem risk assessment due to plausible wreck presence. One of elements of such an assessment is determining the state of the environment in the vicinity of the wreck. In the work presented, the results of studies on surface sediments samples collected around the s/s Stuttgart ship sunk during...
-
The possibility of application of the potentiometric sensor with all-solid-state electrodes containing lipid-polymer membranes for classification of tested black leaf teas in terms of their quality
PublikacjaPotentiometric sensor with all-solid-state electrodes containing lipid-polymer membranes for a set of black leaf teas coming from four countries (China, India, Sri Lanka and Kenia) classification was applied. The tested tea samples were reassigned to quality classes marked with numbers I–V according to the information available. The sensor results of tea samples are presented in the form of radar charts. It was observed that, in...
-
Experience based knowledge representation for Internet of Things and Cyber Physical Systems with case studies
PublikacjaCyber Physical Systems and Internet of Things have grown significant attention from industry and academia during the past decade. The main reason behind this interest is the capabilities of such technologies to revolutionize human life since they appear as seamlessly integrating classical networks, networked objects and people to create more efficient environments. However, enhancing these technologies with intelligent skills becomes...
-
Status report on high temperature fuel cells in Poland – Recent advances and achievements
PublikacjaThe paper presents recent advances in Poland in the field of high temperature fuel cells. The achievements in the materials development, manufacturing of advanced cells, new fabrication techniques, modified electrodes and electrolytes and applications are presented. The work of the Polish teams active in the field of solid oxide fuel cells (SOFC) and molten carbonate fuel cell (MCFC) is presented and discussed. The review is oriented...
-
Piotr Marczak dr inż. arch.
OsobyPiotr Marczak jest adiunktem na Wydziale Architektury Politechniki Gdańskiej, a od 2016 roku Prodziekanem ds. Kształcenia i Rozwoju. Jest również członkiem Pomorskiej Okręgowej Izby Architektów RP (POIA RP). Jego badania i publikacje koncentrują się na teorii architektury, rewitalizacji oraz przekształceń w obrębie portów i pobrzeża Bałtyku. Badania te związane są z kierunkami działań rewitalizacyjnych obszarów i obiektów portowych,...
-
P92 steel and inconel 617 alloy welds joint produced using ERNiCr-3 filler with GTAW process: Solidification mechanism, microstructure, mechanical properties and residual stresses
PublikacjaThe objective of the current study was to analyse the microstructure, mechanical characteristics, and residual stresses of a dissimilar welded joint (DWJ) made of P92 steel and the Inconel alloy 617 (IN617) using the gas tungsten arc welding (GTAW) method. The ERNiCr-3 filler was selected to produce the conventional V groove (VG) and narrow V groove (NVG) butt joint. The filler deficient zones in the weldments, such as the filler...
-
Fatigue Bending of V-Notched Cold-Sprayed FeCoCrNiMn Coatings
PublikacjaCold-spray coatings were produced by FeCoCrNiMn high-entropy alloy powders deposited on carbon steel substrate. The coatings were realized at intermediate temperature and high pressure (at 1100 °C and 7 MPa). The coating microstructure was characterized by scanning electron microscopy and X-ray diffraction, revealing a very dense deposition and high flattening ratio of the splatted particles. This had a large influence on the...