Filtry
wszystkich: 2062
wybranych: 1690
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: BRANDING
-
Comparison of hydrogen bonds and diverse weak interactions of the nitro group in 2-methyl-4-nitroanilinium nitrate, bisulfate and two hexafluoridosilicates: elementary graph-set approach
PublikacjaCrystal structures of (H2m4na)NO3 (1), (H2m4na)HSO4 (2), (H2m4na)2SiF6 (3) and (H2m4na)2SiF6*2H2O (4), where 2m4na = 2-methyl-4-nitroaniline, are presented. Two layers of interactions occur in the structures, N—H...O/F hydrogen bonds and interactions with the nitro group. Although diverse, hydrogen-bonding patterns are compared with each other by means of interrelations among elementary graph-set descriptors and descriptors of hydrogen-bonding...
-
Method for the simultaneous determination of monoaromatic and polycyclic aromatic hydrocarbons in industrial effluents using dispersive liquid-liquid microextraction with GC-MS
PublikacjaWe present a new method for simultaneous determination of 22 monoaromatic and polycyclic aromatic hydrocarbons in postoxidative effluents from the production of petroleum bitumen using dispersive liquid-liquid microextraction coupled to gas chromatography and mass spectrometry. The eight extraction parameters including the type and volume of extraction and disperser solvent, pH, salting out effect, extraction and centrifugation...
-
Application of multicriteria decision analysis in solvent type optimization for chlorophenols determination with a dispersive liquid–liquid microextraction
PublikacjaThis study presents a novel support tool for the optimization and development of analytical methods. The tool is based on multi-criteria decision analysis (MCDA), namely the Technique for Order of Preference by Similarity to the Ideal Solution (TOPSIS), that allows users to rank possible solutions according to their requirements. In this study, we performed rankings of pairs of eight extraction and three dispersive solvents used...
-
Smart Weighing Scale with Feet-Sampled ECG
PublikacjaIn a smart home, health and well-being monitoring systems could be embedded in everyday devices providing a pervasive care. A home bathroom scale is an example of such a device, typically used to measure body weight and very often its composition (e.g. body water/fat percentage). In this paper, we analyzed a potential use of the bathroom scale to measure electrocardiogram (ECG) from electrodes located on the scale's tile. In particular...
-
Stability of an imperfect truss loaded by wind
PublikacjaThe present paper is devoted to the numerical research of stability of a truss loaded by wind and stiffened by elastic supports located at the top chord. The lateral braces or lateral and torsional braces were taken into account. In this paper, the linear buckling analysis re- sults for the beam and shell model were presented. Two different shapes of initial geometric imperfections were considered in the non-linear static analysis...
-
Effect of polymer fibres reinforcement on selected properties of asphalt mixtures
PublikacjaThe paper presents selected results of the research program concerning fibre reinforced asphalt concrete. Aramid-polyalphaolefin fibres was used in this study. Selected properties responsible for low temperature cracking and resistance to permanent deformation are presented in this paper. Low temperature cracking susceptibility was evaluated with the results obtained from bending test of rectangular beams with constant rate of...
-
Analysis of sloping brace stiffness influence on stability and load bearing capacity of a truss
PublikacjaThe paper is focused on the numerical study of stability and load bearing capacity of a truss with side elastic braces. The structure is made in reality. The rotational and sliding brace stiffnesses were taken into account. Linear buckling analysis and non-linear static analysis with geometric and material nonlinearity were performed for the beam and shell model of the truss with respect to the angle of sloping braces. As a result...
-
Developments in manufacturing engineering and machining process planning
PublikacjaCurrent research conducted in the Department of Manufacturing Engineering and Automation is presented in the paper. This includes: abrasive cutting off, grinding with lapping kinematics, rapid prototyping and machining procrss planning. Experimental results and computer simulation are presented and analysed.
-
Protokół głosowania większościowego w narzędziu wsparcia decyzji handlowych
PublikacjaIstnieje szerokie spektrum narzędzi i metod wspierających decyzje handlowe, lecz brakuj jasnych reguł ich stosowania. Zaproponowano samoorganizujacy się system agentowy do wspierania decyzji handlowych. System bazując na glosowaniu z dynamicznymi wagami, wskazuje efektywne indykatory na podstawie ich poprzednich osiągnięć. Przedstawiono analizę formalną i wyniki weryfikacji, potwierdzającej cechy rozwiązania.
-
Underwater Local Cavity Welding of S460N Steel
PublikacjaIn this paper, a comparison of the mechanical properties of high-strength low-alloy S460Nsteel welded joints is presented. The welded joints were made by the gas metal arc welding (GMAW)process in the air environment and water, by the local cavity welding method. Welded joints were testedfollowing the EN ISO 15614-1:2017 standard. After welding, the non-destructive—visual, penetrant,radiographic, and ultrasonic (phased array) tests...
-
Reconstruction of 3D structure of positive corona streamer by local methods
PublikacjaThe computer algorithms were used for reconstruction of streamer 3D structure. We propose the 3D tree structure model of corona discharge streamer composed with nodes and edges between chosen couples of nodes, which enables easy computation of some important parameters ofstreamers. The 3D model can be derived directly from two projection images by global methods like evolutionary searching or particle simulations. In this paper...
-
Karaś P., Kochanowicz K., Pitek M., Domański P., Obuchowski I., Tomiczek B., Liberek K.: Evolution towards simplicity in bacterial small heat shock protein system// eLife -, (2023), s.1-21
PublikacjaEvolution can tinker with multi-protein machines and replace them with simpler single-protein systems performing equivalent functions in an equally efficient manner. It is unclear how, on a molecular level, such simplification can arise. With ancestral reconstruction and biochemical analysis, we have traced the evolution of bacterial small heat shock proteins (sHsp), which help to refold proteins from aggregates using either...
-
Mechanochemical Energy Transduction during the Main Rotary Step in the Synthesis Cycle of F1-ATPase
PublikacjaF1-ATPase is a highly efficient molecular motor that can synthesize ATP driven by a mechanical torque. Its ability to function reversibly in either direction requires tight mechanochemical coupling between the catalytic domain and the rotating central shaft, as well as temporal control of substrate binding and product release. Despite great efforts and significant progress, the molecular details of this synchronized and fine-tuned...
-
Characterization of Bioactivity of Selective Molecules in Fruit Wines by FTIR and NMR Spectroscopies, Fluorescence and Docking Calculations
PublikacjaFourier transform infrared (FTIR) and proton nuclear magnetic resonance (1H NMR) spectroscopies were applied to characterize and compare the chemical shifts in the polyphenols’ regions of some fruit wines. The obtained results showed that FTIR spectra (1800–900 cm−1) and 1H NMR (δ 6.5–9.3 ppm) of different fruit wines can be used as main indices of the year of vintage and quality of fruit wines. In addition to the classical determination...
-
Evolution towards simplicity in bacterial small heat shock protein system
PublikacjaEvolution can tinker with multi-protein machines and replace them with simpler single-protein systems performing equivalent functions in an equally efficient manner. It is unclear how, on a molecular level, such simplification can arise. With ancestral reconstruction and biochemical analysis, we have traced the evolution of bacterial small heat shock proteins (sHsp), which help to refold proteins from aggregates using either two...
-
Ocena odporności na pękanie podbudów drogowych z mieszanek mineralno-cementowo-emulsyjnych (MCE)
PublikacjaPodbudowy z mieszanek mineralno-cementowo-emulsyjnych (MCE) są jednym z wielu materiałów stosowanych do wykonywania warstw nawierzchni w ramach przebudów dróg w Polsce. Mieszanki MCE pozwalają na maksymalne powtórne wykorzystanie istniejących warstw konstrukcyjnych do budowy lub przebudowy nawierzchni. Do wykonania podbudów z MCE stosuje się materiał pochodzący z rozbiórki istniejących warstw (destrukt) bitumicznych, warstw związanych...
-
Interfacial water controls the process of adsorption of hyperactive antifreeze proteins onto the ice surface
PublikacjaA mechanism of interactions between the ice-binding surface of a hyperactive antifreeze protein molecule and the ice surface is proposed, involving the influence of water present between the two surfaces on the behavior of the approaching molecule. It is demonstrated that the interfacial water, even before its full solidification, can act as a factor that pushes away or pulls nearer the protein molecule to ensure its proper positioning....
-
A mobile loop order–disorder transition modulates the speed of chaperonin cycling
PublikacjaMolecular machines order and disorder polypeptides as they form and dissolve large intermolecular interfaces, but the biological significance of coupled ordering and binding has been established in few, if any, macromolecular systems. The ordering and binding of GroES co-chaperonin mobile loops accompany an ATP-dependent conformational change in the GroEL chaperonin that promotes client protein folding. Following ATP hydrolysis,...
-
Cyclic behavior of FeCoCrNiMn high entropy alloy coatings produced through cold spray
PublikacjaeCoCrNiMn high entropy alloy powders were employed to produce coatings on carbon steel through high pressure cold spray (at 1100 °C and 7 MPa in temperature and pressure respectively). X-ray diffraction of the sprayed material revealed a dense coating with the retention of the original crystallographic structure. Once splatted, particles revealed high flattening ratio with consequent excellent adhesion of the coating to the substrate....
-
Microcrack monitoring and fracture evolution of polyolefin and steel fibre concrete beams using integrated acoustic emission and digital image correlation techniques
PublikacjaThe use of polymer and steel fibres in plain concrete appears to be an excellent solution for limiting crack propagation and improving the post-ductility performance of concrete structures. Based on this premise, this study investigated the fracture evolution of polyolefin fibre-reinforced concrete (PFRC) and steel fibre-reinforced concrete (SFRC) specimens through the integrated application of two diagnostic techniques, acoustic...
-
Una crisi diversa?
PublikacjaIl capitolo tratta della recente crisi finanziaria, analizzandone cause e conseguenze per il sistema bancario e finanziario mondiale
-
Mercury contamination, a potential threat to the globally endangered aquatic warbler Acrocephalus paludicola
PublikacjaMercury (Hg) contamination is considered a global concern for humans and wildlife, and although the number of studies dealing with that issue continues to increase, some taxonomic groups such as small passerine birds are largely understudied. In this paper, concentration of mercury in the aquatic warbler (Acrocephalus paludicola) feathers, a globally threatened passerine species, was examined. The concentration differences between...
-
Morphology, Thermo-Mechanical Properties and Biodegradibility of PCL/PLA Blends Reactively Compatibilized by Different Organic Peroxides
PublikacjaReactive blending is a promising approach for the sustainable development of bio-based polymer blends and composites, which currently is gaining more and more attention. In this paper, biodegradable blends based on poly(ε-caprolactone) (PCL) and poly(lactic acid) (PLA) were prepared via reactive blending performed in an internal mixer. The PCL and PLA content varied in a ratio of 70/30 and 55/45. Reactive modification of PCL/PLA...
-
Configurational and Conformational Preferences in Stereoselective Acylations of N-Methyl-1,3-diaminopropane with Acyl Chlorides
PublikacjaEvidence for a stereoinduction profile of the reaction of N-methyl-1,3-diaminopropane with acyl chlorides was provided. A possibility to engage in intramol. CH2···HN and Cl···H-N interactions and the proton migration process to the methylamino group leads to the E secondary amides carrying the N···H+···N or N-H···N bridges, that show unusual spectroscopic images. Empirical relations between the ΔδC chem. shift differences,...
-
Experimental Tests Of Sandwich Beams In The Design Process Of GFRP Shell Footbridge Structure
PublikacjaThe paper includes selected aspects of the study to elaborate architectural, material and construction design of pedestrian footbridge spans made of composite materials. The considered footbridge is a sandwich-type shell structure. The cooperation of PET foam core with outer lining surfaces is crucial for its load bearing capacity. The paper is aimed to experimental investigation of sandwich beams subjected to bending loading....
-
Experimental study and comparison with predictive methods for flow boiling heat transfer coefficient of HFE7000
PublikacjaThis article describes an experimental study of flow boiling of HFE7000 inside a smooth vertical channel. The investigation has been carried out in a circular stainless-steel tube with an inner diameter of 2.3 mm. The data have been collected for the applied heat fluxes q ranging from 61 to 205 kW/m2, the mass flux G ranging from 214 to 1006 kg/(m2 s), the saturation temperature Tsat ranging from 30 to 54 °C and the full range...
-
Influence of effective width of flange on calculation and reinforcement dimensioning of beam of reinforced concrete frame
PublikacjaThe paper analyses the influence of modelling the cross-section of a beam in two-storey reinforced concrete frame of industrial warehouse with dimensions: 18.0 m × 32.0 m using bar elements on the results of bending moments, the value of elastic deflection and the dimensioning of reinforcement due to bending. Six options were considered: a beam as a rectangular section and five T-beam variants with different definitions of effective...
-
Stability of a truss under upward wind loading
PublikacjaThe present paper is devoted to the numerical investigations of stability of a truss under upward wind load. The truss is braced at its the upper cord. A structural variant including lateral braces, or lateral and torsional braces is considered. The research presents the problems of linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity are presented. The initial...
-
Cation sensing by diphenyl-azobenzocrowns
PublikacjaMetal cations complexation and proton binding by 13- and 16-membered diphenyl-azobenzocrowns and diphenyl-hydroxyazobenzocrowns were studied in acetonitrile using spectroscopic methods: UV–vis spectroscopy, spectrofluorimetry, and 1H NMR spectroscopy. Phenyl moieties in benzene rings were found to affect binding strength alkali and alkaline earth metal cations and hydrogen ion, and affect tautomeric equilibrium of hydroxyazobenzocrowns....
-
A New Rehabilitation Device for Balance Impaired Individuals
PublikacjaIn the paper authors present a device designed to improve the rehabilitation process of people with balance impairment. The discussed device (JStep) utilizes a commercially available static standing frame (stander) modified in order to fit force sensing units under the feet and in the pillows around the hips of a patient. While executing rehabilitation tasks, the patient may compensate his balance deficiency by leaning on the pillows...
-
Influence of Asphalt Binder on the Compactability of Asphalt Mixtures Using Locking Point
PublikacjaCompaction is an important process for the asphalt mixture service life. A properly compacted mixture is crucial for long-lasting pavement. The objective of this study was to evaluate the influence of asphalt binders on the compactability of the asphalt mixtures by utilizing the concept of the locking point. To achieve this objective, two compaction methods (impact and gyration), different temperatures and asphalt content, and...
-
Electron-impact ionization cross section calculations for selected ribonucleosides
PublikacjaTotal cross sections for the single electron-impact ionization of selected ribonuclosides (guanosine, adenosine, cytidine and uridine) have been calculated for electron energies ranging from the ionization threshold up to 5 keV.
-
Wpływ zbrojenia polimerowymi włóknami rozproszonymi na wybrane właściwości mieszanek mineralno-asfaltowych
PublikacjaW artykule przedstawiono wybrane wyniki badań mieszanek mineralno-asfaltowych zbrojonych polimerowymi włóknami rozproszonymi. Ocenie poddano mieszankę włókien zbrojących aramidowo-poliolifenowych pod kątem wpływu ich zastosowania na właściwości niskotemperaturowe i odporności na deformacje trwałe mieszanek mineralno-asfaltowych. Właściwości niskotemperaturowe oceniano na podstawie testu zginania próbek belkowych oraz na podstawie...
-
Telomere uncapping by common oxidative guanine lesions: Insights from atomistic models
PublikacjaOxidative damage to DNA is widely known to contribute to aging and disease. This relationship has been extensively studied for telomeres – structures that cap chromosome ends – due to their role in cell proliferation and senescence, and exceptional susceptibility to oxidation. Indeed, the repetitive telomeric DNA sequence contains the 5′-GGG-3′ motif that has the lowest ionization potential of all trinucleotides. Accordingly, experiments...
-
Nonlocal elasticity analysis of moderately thick porous functionally graded plates in a hygro-thermal environment
PublikacjaThis work performs a novel quasi three-dimensional (3D) bending analysis for a moderately thick functionally graded material (FGM) made of nanoceramics and metal powders, in presence of porosities due to some incorrect manufacturing processes. Such porosities can appear within the plate in two forms, namely, even and uneven distributions. The modeled system assumes a polymer matrix where both shear and transverse factors coexist....
-
Bitumen-Based Poroelastic Pavements: Successful Improvements and Remaining Issues
PublikacjaThis article presents the development process of designing and testing poroelastic pavement based on highly polymer-modified bitumen. Poroelastic wearing course was composed of mineral and rubber aggregate mixed with highly polymer-modified bitumen, in contrast to previous trials, during which polyurethane resins were mainly used as binder, which led to several serious technological problems concerning difficult production, insufficient...
-
Shaping the brand awareness of science and technology parks in Eastern Poland
PublikacjaThe main aim of the paper is the analysis of the effects of actions undertaken so far that have aimed at shaping brand awareness of the parks in Eastern Poland, supported under the OP DEP. The authors focused on the demand-side perspectiveand scrutinized two vectors of conscious branding: the surrounding environment and communication with customers. The group of potential customers underwent qualitative research (ITI interviews)....
-
Systemowe ryzyko płynności w polskim systemie bankowym – determinanty i trendy
PublikacjaCelem rozprawy jest określenie metod pomiaru systemowego ryzyka płynności oraz pomiar tego ryzyka dla polskiego systemu bankowego za pomocą zaproponowanych metod, w oparciu o dostępne dane. Do celów rozprawy zaliczyć należy również przedstawienie problemu systemowego ryzyka płynności od strony jego wpływu na gospodarkę. Zgodnie z hipotezą główną, systemowe ryzyko płynności w polskim systemie bankowym w latach 1996-2012 wzrosło....
-
Rigid finite elements and multibody modelling used in estimation and reduction of rod vibrations
PublikacjaIn the paper, a mechanical set composed of a robot (manipulator) and of an elastic beam is considered. The beam is fixed to the top of the robot structure. In most of the similar cases, undesired vibrations can be excited in the beam. They are especially significant, when dynamics in the robot braking period is examined. In the paper, estimation and modification of length of the braking period is proposed, in order to reduce the...
-
Why do G-quadruplexes dimerize through the 5’-ends? Driving forces for G4 DNA dimerization examined in atomic detail
PublikacjaG-quadruplexes (G4) are secondary structures formed by guanine-rich nucleic acid sequences and shown to exist in living cells where they participate in regulation of gene expression and chromosome maintenance. G-quadruplexes with solvent-exposed guanine tetrads show the tendency to associate together through cofacial stacking, which may be important for packaging of G4-forming sequences and allows for the design of higher-order...
-
Kwalifikowanie technologii lutowania twardego próżniowego stali austenitycznej zgodnie z wymaganiami przepisów ASME BPVC, sekcja IX
PublikacjaW artykule przedstawiono procedurę kwalifikowania technologii lutowania twardego w piecu próżniowym na przykładzie elementów ze stali wysokostopowej nierdzewnej austenitycznej łączonych lutem miedzianym z grupy F-No. 105, zgodnie z przepisami ASME Sec. IX, part QB (ASME Boiler and Pressure Vessel Code. Qualification Standard for Welding, Brazing and Fusing; Procedures; Welders; Brazers; and Welding, Brazing and Fusing Operators)....
-
Unusual structural properties of water within the hydration shell of hyperactive antifreeze protein
PublikacjaMany hypotheses can be encountered explaining the mechanism of action of antifreeze proteins. One widespread theory postulates that the similarity of structural properties of solvation water of antifreeze proteins to ice is crucial to the antifreeze activity of these agents. In order to investigate this problem, the structural properties of solvation water of the hyperactive antifreeze protein from Choristoneura fumiferana were...
-
Identification of 1H‐indene‐(1, 3, 5, 6)‐tetrol derivatives as potent pancreatic lipase inhibitors using molecular docking and molecular dynamics approach
PublikacjaPancreatic lipase is a potential therapeutic target to treat diet-induced obesity in humans, as obesity-related diseases continue to be a global problem. Despite intensive research on finding potential inhibitors, very few compounds have been introduced to clinical studies. In this work, new chemical scaffold 1H-indene-(1,3,5,6)-tetrol was proposed using knowledge-based approach, and 36 inhibitors were derived by modifying its...
-
The interactions of monomeric acridines and unsymmetrical bisacridines (UAs) with DNA duplexes: an insight provided by NMR and MD studies
PublikacjaMembers of a novel class of anticancer compounds, exhibiting high antitumor activity, i.e. the unsymmetrical bisacridines (UAs), consist of two heteroaromatic ring systems. One of the ring systems is an imidazoacridinone moiety, with the skeleton identical to the structural base of Symadex. The second one is a 1-nitroacridine moiety, hence it may be regarded as Nitracrine’s structural basis. These monoacridine units are connected...
-
Comparison of Tire Rolling Resistance Measuring Methods for Different Surfaces
PublikacjaThe rolling resistance of car tires is one of the most important parameters characterizing tires today. This resistance has a very significant contribution to the energy consumption of wheeled vehicles. The climate crisis has forced tire and car manufacturers to place great emphasis on the environmental impact of their products. Paradoxically, the development of electric vehicles has led to an even greater importance of rolling...
-
On a 3D material modelling of smart nanocomposite structures
PublikacjaSmart composites (SCs) are utilized in electro-mechanical systems such as actuators and energy harvesters. Typically, thin-walled components such as beams, plates, and shells are employed as structural elements to achieve the mechanical behavior desired in these composites. SCs exhibit various advanced properties, ranging from lower order phenomena like piezoelectricity and piezomagneticity, to higher order effects including flexoelectricity...
-
Structural and Thermo-Mechanical Properties of Poly(ε-caprolactone) Modified by Various Peroxide Initiators
PublikacjaThe modification of poly(ε-caprolactone) (PCL) was successfully conducted during reactive processing in the presence of dicumyl peroxide (DCP) or di-(2-tert-butyl-peroxyisopropyl)-benzene (BIB). The peroxide initiators were applied in the various amounts of 0.5 or 1.0 pbw (part by weight) into the PCL matrix. The effects of the initiator type and its concentration on the structure and mechanical and thermal properties of PCL were...
-
Modification of quaternary structure of Candida albicans GlcN-6-P synthase and its desensitization to inhibition by UDP-GlcNAc by site-directed mutagenesis
PublikacjaSite-directed mutagenesis of the CaGFA1 gene encoding glucosamine-6-phosphate synthase from Candida albicans was performed. Desensitization of the enzyme to inhibition by UDPGlcNAc was achieved upon T487I and H492F substitutions at the UDP-GlcNAc binding site, exchange of D524, S525 and S527 for Ala at the dimer:dimer interface and construction of the tail-lock array (L434R and L460A) at the C-tail region. The first two sets if...
-
FINITE GROUND CPW-FED UWB ANTENNA OVER THE METALLIC CYLINDRICAL SURFACES
PublikacjaThe investigation of finite ground coplanar fed ultra-wideband (UWB) antenna and the influence of its curvature and the proximity of circular metallic screen on the reflection coefficients and radiation characteristics is presented. The antenna is composed of two circular coplanar strips which enclose slot aperture of similar shape and is designed on a thin and flexible substrate which allows its bending. The antenna configuration...
-
Bacteriophages as Factories for Eu2O3 Nanoparticle Synthesis
PublikacjaThe use of phage display to identify peptides with an ability to bind and synthesize Eu2O3 nanoparticles is demonstrated in this report. This is the first report of modified phages specifically binding a lanthanide. The peptides exposed on virions revealed very strong binding to Eu2O3 nanoparticles and the ability to catalyze Eu2O3 nanoparticles’ formation from Eu(OH)3 and Eu(NO3)3 solutions. The luminescence emission spectrum...