Filtry
wszystkich: 2280
wybranych: 1660
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: healthcare entity
-
Development of methods improving storage stability of bitumen modified with ground tire rubber: A review
PublikacjaThe following paper presents an overview of methods for improving the storage stability at high temperature of rubber modified bitumen. The storage stability of the rubber modified bitumen can be improved by using a various types of modifiers that form the bonds between the components of these binders. The increase in stability can also be achieved by using crumbrubber surface-activated by furaldehyde or ground tire rubber (GTR)...
-
The Brain of the city
PublikacjaIn order to highlight the characteristics of the West End of Wrocław, we conducted a site analysis. Using the strengths of the site, we were able to create a unique concept of the district while minimizing the impacts of weaknesses by design. The purpose of redesigning the West End of Wrocław is to attract new people to the district through the transformation of an identity. Initially, we conducted a SWOT analysis to identify the...
-
rigid polyurethane foams modified with selected nanofillers
PublikacjaThe nanofillers: natural montmoryllonite (MMT) - Bentonite, natural MMT modified with a quaternary ammonium salt - Cloisite30B, has been used in rigid polyurethane foams (PUFs). The influence of fillers amounts on processing parameters, physical-mechanical properties (density, water absorption, brittleness and compression strength) and thermal properties (thermal stability, fire behaviours) of such foams has been analysed. The...
-
Analog CMOS processor for early vision processing with highly reduced power consumption
PublikacjaA new approach to an analog ultra-low power visionchip design is presented. The prototype chip performs low-levelconvolutional image processing algorithms in real time. Thecircuit is implemented in 0.35 μm CMOS technology, contains64 x 64 SIMD matrix with embedded analogue processors APE(Analogue Processing Element). The photo-sensitive-matrix is of2.2 μm x 2.2 μm size, giving the density of 877 processors permm2. The matrix dissipates...
-
Numerical analysis of crack propagation in silicone nitride
PublikacjaThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculation...
-
Sensors in River Information Services of the Odra River in Poland: Current State and Planned Extension
PublikacjaAccording to adopted in 2016 by the polish Council of Ministers assumptions for the plans for the progress of inland waterways in Poland for the years 2016-2020, with the perspective of 2030, assume that by 2030 Odra along its entire length and the Vistula from Warsaw to Gdansk, they will have become international shipping routes, which will be implemented system of River Information Services (RIS). Aspects of RIS sensor application...
-
Radioisotope measurements of the liquid-gas flow in the horizontal pipeline using phase method
PublikacjaThe paper presents application of the gamma-absorption method to a two-phase liquid-gas flow investigation in a horizontal pipeline. The water-air mixture was examined by a set of two Am-241 radioactive sources and two NaI(Tl) scintillation probes. For analysis of the electrical signals obtained from detectors the cross-spectral density function (CSDF) was applied. Results of the gas phase average velocity measurements for CSDF...
-
Structure and thermal expansion of liquid bismuth
PublikacjaExperimental structural data for liquid Bi were used for estimation of the main structure parameters as well as the thermal expansion coefficient both in supercooled and superheated temperature ranges. It was shown that the equilibrium melt had a positive thermal expansion coefficient within a temperature range upon melting and a negative one at higher temperatures. The former was related to structure changes upon melting, whereas...
-
Possibilities of radioisotope measuring in control of an unstable solid particles hydrotransport
PublikacjaThe paper presents γ-radiation proposal to control a multiphase flow, independently from circumstances. So this method may be applied even in compound industrial or environmental processes. Moreover in many cases, it is the only method for applications for dense mixture containing coarse angular grains. The constructed equipment allows continuous measurement of density as well as solid phase for both concentration and average velocity....
-
Ultrasound monitoring for evaluation of damage in reinforced concrete
PublikacjaThe paper deals with automated monitoring of damage evolution in concrete elements subjected to three-point bending tests. The monitoring is based on the nonlinear interactions of traveling ultrasonic waves with micro-crack zones inside the concrete specimens and surface-breaking cracks. The developed procedure assumes semi-continuous ultrasonic testing during the element full loading cycle and generation of the power spectral...
-
3D POINT-CLOUD SPATIAL EXPANSION BY TOTAL LEAST-SQUARES LINE FITTING
PublikacjaPoint-cloud spatial expansion (PCSE) allows the creation of a new pointcloud form that presents an alternative geometry of an entire object in a single spatial view. Spatial expansion facilitates the analysis process and introduces an additional spatial parameter describing the point cloud. An important element of the PCSE method is determining the position of the axis of symmetry of a symmetrical object: the procedure for determining...
-
Microstructure–Property Relationship of Polyurethane Foams Modified with Baltic Sea Biomass: Microcomputed Tomography vs. Scanning Electron Microscopy
PublikacjaIn this paper, novel rigid polyurethane foams modified with Baltic Sea biomass were compared with traditional petro-based polyurethane foam as reference sample. A special attention was focused on complex studies of microstructure, which was visualized and measured in 3D with high-resolution microcomputed tomography (microCT) and, as commonly applied for this purpose, scanning electron microscopy (SEM). The impact of pore volume,...
-
Modernized cathodic protection system for legs of the production rig – Evaluation during ten years of service
PublikacjaThe modernization of cathodic protection system of the Baltic Beta platform legs is described. It was that the sacrificial anodes cone-shaped groups were to be placed on the seabed at a depth of 80 m. The measurements results of cathodic protection effectiveness during its ten-years operation are presented. The effectiveness was assessed based on the potential value along the entire length of the legs from the sea surface to the...
-
Thermodynamical approach to quantifying quantum correlations
PublikacjaWe consider the amount of work which can be extracted from a heat bath using a bipartite state ρ shared by two parties. In general it is less then the amount of work extractable when one party is in possession of the entire state. We derive bounds for this “work deficit” and calculate it explicitly for a number of different cases. In particuar, for pure states the work deficit is exactly equal to the distillable entanglement of...
-
Kultura jakości, doskonałości i bezpieczeństwa w organizacji
PublikacjaKultura jakości, bezpieczeństwa oraz doskonałości to ważne, kategorie zasobów każdej organizacji, decydujące o jej niepowtarzalności. Kształtują one nie tylko tożsamość danej organizacji, ale także mają wpływ na jej zdolność do spełniania potrzeb różnych grup interesariuszy oraz na szeroko rozumianą reputację na rynku. Każda z tych kultur wyraża się poprzez swoiste założenia, normy, wartości oraz artefakty. Stanowią one fundament...
-
ANALIZA STANU TECHNICZNEGO RUROCIĄGÓW: WODY PRZeMYSŁOWEJ I SOLANKI
PublikacjaPracę wykonano na zlecenie Przedsiębiorstwa Badawczo-Wdrożeniowego "HYDRO-POMP" Sp. z o.o. ul. Wróblewskiego 19, 93-578 Łódź. Wykonawcą zlecenia jest Politechnika Gdańska, Wydział Chemiczny, Katedra Elektrochemii, Korozji i Inżynierii Materiałowej, 80-233 Gdańsk, ul. G. Narutowicza 11/12. Celem pracy była analiza stanu technicznego i badania dwóch rurociągów: solanki oraz wody przemysłowej. Badania wykonywano w warunkach terenowych...
-
Uniwersalny program komputerowy do projektowania zmiany kierunku trasy
PublikacjaW pracy przedstawiono kolejny program komputerowy stanowiący implementację algorytmu obliczeniowego dotyczącego projektowania zmiany kierunku trasy kolejowej, dostosowanego do techniki ciągłych pomiarów satelitarnych. Program ten ma charakter uniwersalny, gdyż w ogólnym przypadku obejmuje wprowadzenie do układu geometrycznego dwóch łuków kołowych o różnym promieniu, czyli zastosowanie łuku koszowego. Może się to okazać szczególnie...
-
ZRÓŻNICOWANIE STRUKTURY KAPITAŁOWO-MAJĄTKOWEJ W ZALEŻNOŚCI OD WIELKOŚCI PRZEDSIĘBIORSTWA
PublikacjaW artykule przedstawiono różnice w kształtowaniu struktury kapitałowo-majątkowej pomiędzy małymi, średnimi i dużymi przedsiębiorstwami. W trakcie przeprowadzonych badań uwzględniono 97 471 sprawozdań finansowych przedsiębiorstw, prowadzących działalność gospodarczą w 12 różnych działach polskiej gospodarki narodowej. Do potwierdzenia zróżnicowania struktury kapitałowo-majątkowej w zależności od wielkości przedsiębiorstwa wykorzystano...
-
OCENA NOŚNOŚCI STAREGO MOSTU ŁUKOWEGO W JAGODNIKU
PublikacjaArtykuł opisuje przeprowadzoną analizę statyczno-wytrzymałościowa 95-letniego betonowego mostu łukowego zlokalizowanego w Jagodniku w północnej Polsce. Trwałość i wytrzymałość starego betonu są określane na podstawie wybranych właściwości mechanicznych, fizycznych i chemicznych. Program badań laboratoryjnych składał się z następującego zestawu badań: pomiary głębokości strefy skarbonatyzowanej i gęstości w stanie suchym, badania...
-
Bio-inspired Urban Design: Smart Growth and Sustainable Development Frameworks for a New Urban Unit in Cracow
PublikacjaIn March 2012, architects João Diniz (Brazil) and Dorota Wiśniewska (Poland) answered a call to competition from the City of Cracow, submitting an entry for the redesign of 5600 ha of the Nowa Huta district in eastern Cracow, focusing on economic revitalization within a framework of smart growth and sustainable development. The scenario included an ArcerolMittal Steelworks and incorporated a strong ecological analysis for the easternmost...
-
Alternative Energy: Photovoltaic Modules and Systems
PublikacjaUse of solar energy does not contribute to global warming. The light-to-current conversion (photovoltaic conversion) takes place within solar cells, which in most cases are made of silicon. Solar module consists of many solar cells, which are electrically connected and placed between glass or Tedlar® and framed by an aluminium frame. A number of solar modules and other components form photovoltaic systems. In this entry, a brief...
-
Hydrogen migration in formation of NH(A3Π) radicals via superexcited states in photodissociation of isoxazole molecules
PublikacjaFormation of the excited NH(A 3Π) free radicals in the photodissociation of isoxazole (C3H3NO) molecules has been studied over the 14-22 eV energy range using photon-induced fluorescence spectroscopy. The NH(A 3Π) is produced through excitation of the isoxazole molecules into higher-lying superexcited states. Observation of the NH radical, which is not a structural unit of the isoxazole molecule, corroborates the hydrogen atom...
-
Macro-elements and Model Order Reduction for Efficient Three-Dimensional FEM Analysis
PublikacjaAn efficient model order reduction (MOR) methodology for three dimensional vector finite element method (FEM) is developed to accelerate simulations of the structures containing features that cause strong variations of mesh density. As the result of presented algorithm, FEM subsystems of equations corresponding to the selected refined region are converted into a very compact sets of linear equations, called macro-elements.Numerical...
-
SafeCity – a GIS-based tool profiled for supporting decision making in urban development and infrastructure protection
PublikacjaThis paper presents a system for analysis of municipal Critical Infrastructures, which offers integrated tools for target analysis, hazard scenario simulations and spatial analysis within a remotely accessible Web-based Geographic Information System. The system has been applied to research conducted in the city of Gdansk with the aid of blast attack, chemical leakage and flood hazard scenarios, as well as a spatial density algorithm,...
-
DESIGN AND STRENGTH CALCULATIONS OF THE TRIPOD SUPPORT STRUCTURE FOR OFFSHORE POWER PLANT
PublikacjaThe support structure being the object of the analysis presented in the article is Tripod. According to the adopted assumptions, it is a foundation gravitationally set in the water region of 60 m in depth, not fixed to the seabed, which can be used for installing a 7MW wind turbine. Due to the lack of substantial information on designing and strength calculations of such types of structures in the world literature, authors have...
-
Low temperature deposition of dense MnCo 2 O 4 protective coatings for steel interconnects of solid oxide cells
PublikacjaIn this work manganese cobalt spinel (MnCo2O4) coatings were deposited on steel substrates by spray pyrolysis at 390 °C. This is at much lower temperatures than previously reported (typically in excess of 900 °C). It was possible to produce coatings with well controlled thickness (2-5-10 μm). The as-deposited coatings were evaluated for their microstructural changes and electrical conductivity up to 800 °C. Results confirm the...
-
Evaluation of the structures size in the liquid-gas flow by gamma-ray absorption
PublikacjaThe rapid development of tomography methods particularly electrical, X and gamma rays allows for a wide range of the information about flow structure. However, all of such methods are quite complicated. At the same time much simpler systems as the measuring system of gamma rays absorption, allows to obtain a all key flow information which describe the two-phase flow. In the article the results of analyzes of radiometric signal...
-
Analysis of measurement uncertainty for contact-less method used to measure the position of catenary contact wire, performed with the use of Monte Carlo method
PublikacjaCurrently the majority of main railway lines in Europe are electrified, and electric trains have the biggest share in the entire amount of rail transport. Reliability of electrified railways is closely related to the issue of supplying traction vehicles with energy. The problems connected with diagnostics of energy consumption node, namely the contact line and the current collector, are therefore of fundamental importance for maintaining...
-
A variational approach of homogenization of piezoelectric composites towards piezoelectric and flexoelectric effective media
PublikacjaThe effective piezoelectric properties of heterogeneous materials are evaluated in the context of periodic homogenization, whereby a variational formulation is developed, articulated with the extended Hill macrohomogeneity condition. The entire set of homogenized piezoelectric moduli is obtained as the volumetric averages of the microscopic properties of the individual constituents weighted by the displacement and polarization...
-
Failure characterisation of sandwich beams using integrated acoustic emission and digital image correlation techniques
PublikacjaThe paper presents the experimental study of the failure behaviour of sandwich beams subjected to bending. The samples examined are sandwich beams made of polyethylene terephthalate foam core and glass fibre-reinforced polymer laminate face sheets. In a series of experiments, it has been proposed to integrate diagnostic techniques with acoustic emission and digital image correlation to accurately track the cracking process on the...
-
Large Hydrodynamic Thrust Bearings and Their Application in Hydrogenerators
PublikacjaLarge hydrodynamic thrust bearings are the bearings which, due to hydrodynamic lubrication, allow large axial load to be transferred from a moving part (shaft) to the stationary part via a thin layer of the lubricant (usually oil), thus providing extremely low friction and practically no wear. Hydrogenerators with vertical shafts are the most important application of large thrust bearings. Main design and scientific problems of...
-
City as a product. Architecture as an Economic Instrument. Are Global Cities People-Friendly Places?
PublikacjaWhile spending time in our everyday urban environment do we ever think how particular architecture influences the economic value of that space? Space has its measurable financial value. From the economic point of view a place can be treated as a product that fights for appearing in tourists’ and investors’ consciousnesses. Space - treated as an object of demand and supply - becomes an element in a marketing game. To reach its...
-
Recombinant !ermostable AP Exonuclease from Thermoanaerobacter tengcongensis: Cloning, Expression, Purification, Properties and PCR Application
PublikacjaApurinic/apyrimidinic (AP) sites in DNA are considered to be highly mutagenic and must be corrected to preserve genetic integrity, especially at high temperatures. !e gene encoding a homologue of AP exonuclease was cloned from the thermophilic anaerobic bacterium Thermoanaerobacter tengcongensis and transformed into Escherichia coli. The protein product showed high identity (80%) to human Ape1 nuclease, whereas to E. coli exonuclease...
-
Personal branding of artists and art-designers: necessity or desire?
PublikacjaPurpose Personal branding becomes a new in-demand skill for all professionals today. To be well-known helps to achieve success in the networked business environment. Personal relationships and a good reputation in the reality of network economy help young artists and art designers move up the career ladder. This paper aims to discuss a problem of artists who often find it difficult to define their artistic and self-distinction...
-
Discrimination of Apple Liqueurs (Nalewka) Using a Voltammetric Electronic Tongue, UV-Vis and Raman Spectroscopy
PublikacjaThe capability of a phthalocyanine-based voltammetric electronic tongue to analyze strong alcoholic beverages has been evaluated and compared with the performance of spectroscopic techniques coupled to chemometrics. Nalewka Polish liqueurs prepared from five apple varieties have been used as a model of strong liqueurs. Principal Component Analysis has demonstrated that the best discrimination between liqueurs prepared from different...
-
An Aqueous Exfoliation of WO3 as a Route for Counterions Fabrication—Improved Photocatalytic and Capacitive Properties of Polyaniline/WO3Composite
PublikacjaIn this paper, we demonstrate a novel, electrochemical route of polyaniline/tungsten oxide (PANI)/WO3) film preparation. Polyaniline composite film was electrodeposited on the FTO (fluorine-doped tin oxide) substrate from the aqueous electrolyte that contained aniline (monomer) and exfoliated WO3 as a source of counter ions. The chemical nature of WO3 incorporated in the polyaniline matrix was investigated using X-ray photoelectron...
-
Superhydrophobic sponges based on green deep eutectic solvents for spill oil removal from water
PublikacjaThe paper described a new method for crude oil-water separation by means of superhydrophobic melamine sponges impregnated by deep eutectic solvents (MS-DES). Due to the numerous potential of two-component DES formation, simple and quick screening of 156 non-ionic deep eutectic solvents using COSMO-RS (Conductor-like Screening Model for Real Solvents) computational model was used. DES which were characterized by high solubility...
-
Quasi-one-dimensional exchange interactions and short-range magnetic correlations in CuTeO4
PublikacjaCuTeO4 has been proposed as a crystallographically distinct, yet electronic structure analog, of the superconducting cuprates. Here, we present a detailed characterization of the physical properties of CuTeO4 to address this proposal. Fitting of magnetic susceptibility data indicates unexpected quasi-one-dimensional, antiferromagnetic correlations at high temperature, with a nearest-neighbor Heisenberg exchange of 1=164(5) K....
-
Design and Optimization of a Compact Super-Wideband MIMO Antenna with High Isolation and Gain for 5G Applications
PublikacjaThis paper presents a super-wideband multiple-input multiple-output (SWB MIMO) antenna with low profile, low mutual coupling, high gain and compact size for microwave and millimeter wave (mm-wave) fifth-generation (5G) applications. A single antenna is a simple elliptical-square shape with a small physical size of 20 × 20 × 0.787 mm3. The combination of both square and elliptical shapes results in an exceptionally broad impedance...
-
Structure versus hydrolytic and thermal stability of bio-based thermoplastic polyurethane elastomers composed of hard and soft building blocks with high content of green carbon
PublikacjaNowadays, sustainability plays a key role in the design and synthesis of new materials. One of the methods for the preparation of green materials is incorporation into their structure the monomers with a high content of green carbon. Therefore, the aim of this work was to investigate the influence of the type and molecular mass of two bio-based polyester polyols and bio-glycol on the properties of aliphatic partially bio-based...
-
Reaction of aniline with ammonium persulphate and concentrated hydrochloric acid: Experimental and DFT studies
PublikacjaIn this paper, the reaction of aniline with ammonium persulphate and concentrated HCl was studied. As a result of our experimental studies, 2,4,6-trichlorophenylamine was identified as the main product. This shows that a high concentration of HCl does not favour oxidative polymerisation of phenylamine, even though the ammonium persulphate/HCl system is widely used in polyaniline synthesis. On the basis of the experimental data...
-
Promising Nanoparticle-Based Heat Transfer Fluids—Environmental and Techno-Economic Analysis Compared to Conventional Fluids
PublikacjaProviding optimal operating conditions is one of the major challenges for effective heating or cooling systems. Moreover, proper adjustment of the heat transfer fluid is also important from the viewpoint of the correct operation, maintenance, and cost efficiency of these systems. Therefore, in this paper, a detailed review of recent work on the subject of conventional and novel heat transfer fluid applications is presented. Particular...
-
A Method of Object Re-identiciation Applicable to Multicamera Surveillance Systems
PublikacjaThe paper addresses some challenges pertaining to the methods for tracking of objects in multi-camera systems. The tracking methods related to a single Field of Vision (FOV) are quite different from inter-camera tracking, especially in case of non-overlapping FOVs. In this case, the processing is directed to determine the probability of a particular object’s identity seen in a pair of cameras in the presence of places non-observed...
-
The principles of arturbain.fr for teaching sustainable urban design
PublikacjaThe article is an attempt to show how important it is in the contemporary education of architecture students to use an ordered repertoire of principles and concepts of a universal nature, at the same time, pointing to the new directions of solutions and answers to the problems of the 21st century. This task is implemented by the French Association L'Arturbain dans les Territoires. It is accompanied by an idea consisting in observing...
-
Structure of the interlayer between Au thin film and Si-substrate: Molecular Dynamics simulations
PublikacjaInteraction between 2, 3, 5 and 7 atomic layers of gold and a (111) silicon surface was investigated with the molecular dynamics simulation method. The simulation of the diffusion interaction between gold and silicon in the temperature range 425-925 K has been carried out. The peculiarities of the concentration changes of the interacting components and the atomic density at the boundary...
-
Education of Logisticians in Poland: Problems and Prospects in Students’ Opinion
PublikacjaLogistics is one of the key sectors of the Polish economy. Its value reflects not only its own capacity, but also the role it plays in ensuring the proper functioning of the entire economy. The rapid development of the industry and the highest demands on logistics solutions bring to the fore the problem of preparing a new generation of specialists in logistics. That is why the question of compliance to learning expectations of...
-
Dissociative electron attachment to benzoic acid (C7H6O2)
PublikacjaThe dissociative electron attachment (DEA) to benzoic acid (C6H5COOH) has been studied using an experimental crossed beam setup of a quadrupole mass spectrometer and a trochoidal electron monochromator. Relative partial cross sections for the DEA to produce negative ion fragments show the main channels for dissociation. The comparison of the present results with the ultraviolet photoelectron spectrum of benzoic acid [J. Meeks,...
-
In Situ Verification of Numerical Model of Water Hammer in Slurries
PublikacjaThis paper presents a numerical model of transient flow in a pressure slurry pipeline network with verification based on in situ measurements. The model, primarily verified in laboratory conditions, has been extended and applied to the case of a large and complex slurry pipeline network in Poland. In the model, the equivalent density concept was applied. In situ experiments were performed for various unsteady flow episodes, caused by...
-
Re-thinking the city in the context of suburban landscapes. The case of Visula River delta water - landscapes and urban transformation processes in Gdańsk
PublikacjaThe text draws attention to the significant role of landscape formations surrounding the city and their role in marking out directions for the transformation and development of urban areas with the particular emphasis on public spaces. The article presents the need for a more conscious design strategies that are based on connectedness of urban spaces, which is built on landscape's characteristics, as an essential starting point...
-
Morphology of bio-based polyurethane composites filled by mer-cerized or silanized natural fibres
PublikacjaBio-composites are materials which possess unique properties and undergo biodegra-dation under specific conditions. Bio-composites belong to the group of materials produced with the use of renewable raw materials. They contain reinforcement, mainly in the form of natural fiber, which has high stiffness and resistance; filler powders are less frequently used. Significant features of natural fibers are elongation, density, thermal...