Filtry
wszystkich: 1609
wybranych: 1194
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: EXTERNAL VISCOSITY
-
Transport properties of aqueous ionic liquid microemulsions: influence of the anion type and presence of the cosurfactant
PublikacjaTransport properties, viz. specific conductivity, dynamic viscosity and apparent diffusion coefficients, were measured as a function of water content in aqueous ionic liquid microemulsions containing 1-butyl-3- methylimidazolium hexafluorophosphate, [BMIM][PF6] and bis(trifluoromethanesulphonyl)imide, [BMIM][Tf2N], stabilized by the nonionic surfactant TX-100, or its mixture with a cosurfactant, i.e. butanol. The investigation covered...
-
Thermophysical study of the binary mixtures of triethyl phosphate with N-methylformamide, N,N-dimethylformamide and N,N-dimethylacetamide – Experimental and theoretical approach
PublikacjaDensities at (293.15, 298.15, 303.15 and 308.15) K, and viscosities and ultrasonic velocities at 298.15 K of binary liquid mixtures of triethyl phosphate with N-methylformamide, N,N-dimethylformamide and N,N-dimethylacetamide have been measured over the entire range of composition at p = 0.1 MPa. From the experimental data, values of excess molar volume, excess isentropic compressibility, viscosity deviation and excess Gibbs energy...
-
Studies on formation and percolation in ionic liquids/TX-100/water microemulsions
PublikacjaTernary microemulsion systems of H2O/Triton X-100/[BMIM][Tf2N], and H2O/Triton X-100/[BMIM][PF6] were prepared, compared and characterized for phase behavior for different water/surfactant ratios, at 25 °C. It was found that a change of an anion structure in the ionic liquids determines the total monophasic area of the systems. A liquid crystalline mesophase was detected in H2O/Triton X-100/[BMIM][PF6]. The microemulsion domains...
-
Eco-Friendly Ether and Ester-Urethane Prepolymer: Structure, Processing and Properties
PublikacjaThis study concerns bio-based urethane prepolymers. The relationship between the chemical structure and the thermal and processing parameters of bio-based isocyanate-terminated ether and ester-urethane prepolymers was investigated. Bio-based prepolymers were obtained with the use of bio-monomers such as bio-based diisocyanate, bio-based polyether polyol or polyester polyols. In addition to their composition, the bio-based prepolymers...
-
Corrosion degradation of spacers – examination of changes in bone cement coating.
PublikacjaSpacer is a special implant used at the time of infection after endoprosthetic surgery. It consists of a metal core and bone cement coating with an antibiotic. In the human body spacers are exposed to degradation processes. This paper looks at the effect of corrosion on spacers. Electrochemical corrosion tests were performer on titanium pins with bone cement coating in two solutions: Ringer’s solution and artificial...
-
Do mistakes acceptance foster innovation? Polish and US cross-country study of tacit knowledge sharing in IT
PublikacjaAbstract Purpose – This study aims to understand and compare how the mechanism of innovative processes in the information technology (IT) industry – the most innovative industry worldwide – is shaped in Poland and the USA in terms of tacit knowledge awareness and sharing driven by a culture of knowledge and learning, composed of a learning climate and mistake acceptance. Design/methodology/approach – Study samples were drawn from...
-
Direction-of-Arrival Estimation Methods in Interferometric Echo Sounding
PublikacjaNowadays, there are two leading sea sounding technologies: the multibeam echo sounder and the multiphase echo sounder (also known as phase-dierence side scan sonar or bathymetric side scan sonar). Both solutions have their advantages and disadvantages, and they can be perceived as complementary to each other. The article reviews the development of interferometric echo sounding array configurations and the various methods applied...
-
Advances in analysis, quantification and modelling of N2O emission in SBRs under various DO set points
PublikacjaNitrous oxide (N2O), considered a major greenhouse gas (GHG) in wastewater treatment plants (WWTPs), is produced during both nitrification and denitrification processes; hence, it needs to be controlled by internal and external strategies. Various factors, such as DO, temperature, and pH, could be incorporated into the mitigation of emissions in WWTPs. In this research, potential operational strategies were investigated in order...
-
CONDITIONS OF THE GREEN TRANSFORMATION. THE CASE OF THE EUROPEAN UNION
PublikacjaThe main purpose of the paper is to identify the factors that determine the course of green transformation and to assess the current stage and possible directions of change in subsequent years in EU countries. The literature lacks comprehensive studies that show the impact of diverse types of factors on the course of green transformation. For this purpose, two perspectives of the research – economic and environmental – are usually...
-
Molecular modelling of membrane activity of amphotericin B, a polyene macrolide antifungal antibiotic
PublikacjaPraca dotyczy różnego typu modelowań molekularnych cząsteczki przeciwgrzybowego antybiotyku (amfoterycyny B). Praca przeglądowa obejmuje opis badań nad właściwościami molekularnymi samej cząsteczki antybiotyku, jej oddziaływań z powierzchnią błony oraz struktur kanałowych jakie tworzą cząsteczki amfoterycyny wewnątrz błony lipidowej.
-
Assessment of crack resistance of ship steels according to SEP 1390 standard
PublikacjaThe aim of the study was to evaluate the weldability of E36 nd NVE-36 steels by bending test according to SEP 1390. In the case of the specimen from E36 steel 9 external cracks were found, 5 of which were stopped in the fusion line and 4 in heat affected zone. In the case of the specimen from NVE-36 steel 8 external cracks were found, 4 of which were stopped in the fusion line and 4 in heat affected zone. Results of bending test...
-
The influence of different glycerine purities on chemical recycling process of polyurethane waste and resulting semi‐products
PublikacjaChemical recycling is the most favourable recycling method due to the possibility of polyol recovery. This work is dedicatedto the utilisation of crude glycerine and polyurethane waste. It aims at determining the impact of the use of glycerine fromthe production of biodiesel with various degrees of purity as a cleavage agent on the decomposition process of polyurethanefoam. The influence of glycerine purit y on the chemical structure...
-
Losses and power balance in hydraulic satellite motor supplied with oil and HFA-E emulsion
PublikacjaMineral oil and HFA-E emulsion are liquids which differ in viscosity, density and lubricant properties. Therefore, supplying hydraulic satellite motor with these liquids, differences between quantity of hydraulic, volumetric and mechanical losses are observed. These losses influence efficiency of conversion of hydraulic energy into mechanical energy and thereby power balance of motor. The research of satellite motor has been conducted...
-
Nodal models of Pressurized Water Reactor core for control purposes – A comparison study
PublikacjaThe paper focuses on the presentation and comparison of basic nodal and expanded multi-nodal models of the Pressurized Water Reactor (PWR) core, which includes neutron kinetics, heat transfer between fuel and coolant, and internal and external reactivity feedback processes. In the expanded multi-nodal model, the authors introduce a novel approach to the implementation of thermal power distribution phenomena into the multi-node...
-
The effect of microemulsion composition on the morphology of Pd nanoparticles deposited at the surface of TiO2 and photoactivity of Pd-TiO2
PublikacjaA series of microemulsion (ME) system, constituted by different water to surfactant molar ratios (Wo) and oil to surfactant mass ratios (S), have been applied for Pd-TiO2 preparation. The effect of ME properties on the morphology of Pd nanoparticles formed at TiO2 surface and an effect of Pd size and distribution on the surface and photocatalytic properties of Pd-TiO2 were investigated. Microemulsion systems were characterized...
-
Wybrane elementy projektowania budynków wielofunkcyjnych stanowiących miejskie centra logistyczne
PublikacjaCelem artykułu jest przedstawienie wybranych aspektów dotyczących projektowania budynków wielofunkcyjnych stanowiących miejskie centra logistyczne. Centrum logistyczne lokalizowane w obszarze zurbanizowanym jest formalnie obiektem, który ma na celu zaspokojenie wielu potrzeb funkcjonalnych względem potencjalnych użytkowników. Miejskie centrum logistyczne stanowi swego rodzaju system, którego podstawą jest sprawna obsługa procesów...
-
Effect of free water on the quasi‑static compression behavior of partially‑saturated concrete with a fully coupled DEM/CFD approach.
PublikacjaThe work aims to numerically investigate the quasi-static response of partially fluid-saturated concrete under two-dimensional uniaxial compression at the mesoscale. We investigated how the impact of free pore fluid content (water and gas) affected the quasi-static strength of concrete. The totally and partially fluid-saturated concrete behavior was simulated using an improved pore-scale hydro-mechanical model based on DEM/CFD....
-
Teoretyczno-doświadczalne modelowanie konwekcji wymuszonej nanocieczy
PublikacjaPrzedłożona rozprawa doktorska dotyczy badań eksperymentalnych oraz numerycznych konwekcji wymuszonej nanocieczy. Badane nanociecze wytworzone były z cieczy bazowych takich jak woda demineralizowana i mieszaniny wody z glikolem etylenowym w trzech proporcjach objętościowych 90:10, 80:20 i 60:40. Jako nanocząstki użyto Al2O3, a wytworzone nanociecze miały koncentracje masowe 0,1%, 1% i 5%. Wyznaczono eksperymentalnie dynamiczny...
-
Application of Multivariate Adaptive Regression Splines (MARSplines) Methodology for Screening of Dicarboxylic Acids Cocrystal Using 1D and 2D Molecular Descriptors
PublikacjaDicarboxylic acids (DiAs) are probably one of the most popular cocrystals formers. Due to the high hydrophilicity and non-toxicity, they are promising solubilizes of active pharmaceutical ingredients (APIs). Although DiAs appear to be highly capable of forming multicomponent crystals with various compounds, some systems reported in the literature are physical mixtures the solid state without forming stable intermolecular complex....
-
Predicting Value of Binding Constants of Organic Ligands to Beta-Cyclodextrin: Application of MARSplines and Descriptors Encoded in SMILES String
PublikacjaThe quantitative structure–activity relationship (QSPR) model was formulated to quantify values of the binding constant (lnK) of a series of ligands to beta–cyclodextrin (β-CD). For this purpose, the multivariate adaptive regression splines (MARSplines) methodology was adopted with molecular descriptors derived from the simplified molecular input line entry specification (SMILES) strings. This approach allows discovery of regression...
-
Modelling of planar movement dynamics of upper limb
PublikacjaThe original model describing planar movement dynamics of upper limb is presented. The upper limb is modelled as two-joints system loaded by external forces and internal forces of striated skeletal muscles. A behaviour of each muscle is modelled as a system composed of serially linked rheologic fragments that have different mechanical properties. These muscle models allow us to simulate a behaviour of short fusiform muscle (3DOF...
-
Accuracy improvement of the prestressed concrete structures precise geometry assessment by use of bubble micro-sampling algorithm
PublikacjaPrestressed concrete structures are well-known technology for a vast period, but nevertheless, this very technology is a leading solution, currently used in construction industry. Prestressed concrete structures have a huge advantage over conventional methods because it uses the properties of concrete in a very efficient way. The main idea behind this technology is to introduce into the cross-section of the structure, the internal...
-
Influence of Annealing Atmospheres on Photoelectrochemical Activity of TiO2 Nanotubes Modified with AuCu Nanoparticles
PublikacjaIn this article, we studied the annealing process of AuCu layers deposited on TiO2 nanotubes (NTs) conducted in various atmospheres such as air, vacuum, argon, and hydrogen in order to obtain materials active in both visible and UV–vis ranges. The material fabrication route covers the electrochemical anodization of a Ti plate, followed by thin AuCu film magnetron sputtering and further thermal treatment. Scanning electron microscopy...
-
Reliable Microwave Modeling By Means of Variable-Fidelity Response Features
PublikacjaIn this work, methodologies for low-cost and reliable microwave modeling are presented using variable-fidelity response features. The two key components of our approach are: (i) a realization of the modeling process at the level of suitably selected feature points of the responses (e.g., S-parameters vs. frequency) of the structure at hand, and (ii) the exploitation of variable-fidelity EM simulation data, also for the response...
-
Asymmetric Renyi Problem and > PATRICIA Tries
PublikacjaIn 1960 R´enyi asked for the number of random queries necessary to recover a hidden bijective labeling of n distinct objects. In each query one selects a random subset of labels and asks, what is the set of objects that have theselabels? Weconsider here anasymmetric version of the problem in which in every query an object is chosenwith probability p > 1/2 and we ignore “inconclusive” queries. We study the number of queries needed...
-
Combined thrust radial bearing of a submarine main shaft – Design and analysis of failure
PublikacjaThis paper presents an analysis of the combined thrust radial bearing of a submarine propulsion shaft. The lubrication system of the bearing is based on a fixed ring. The efficiency of the lubrication system depends on the shaft speed and temperature, which affects oil viscosity. In turn, the thrust bearing load also depends on the rotational speed of the shaft, because as the speed increases, the drag of the ship increases simultaneously,...
-
INFLUENCE OF NANOPARTICLE CONCENTRATION ON THERMAL PROPERTIES OF THERMAL OIL-MWCNT NANOFLUID
PublikacjaThis paper deals with measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of thermal oil-MWCNT (TO-MWCNT) nanofluid. Nanoparticles were tested at the concentration of 0.001%, 0.005%, 0.01%, 0.05%, and 0,1% by weight. Ultrasonic vibration was used in order to stabilize the dispersion of the nanoparticles. Thermal oil (TO) was selected as a base liquid, because of possible application in ORC systems...
-
Integration of inertial sensors and GPS system data for underwater navigation
PublikacjaThe Inertial Navigation System (INS) is usually employed to determine the position of an underwater vehicles, like Remotely Operated Vehicles (ROV) and, more recently, Autonomous Underwater Vehicle (AUV). The accuracy of the position provided by the INS, which uses accelerometers and gyroscopes, deteriorates with time. An external aiding sources such as the Global Positioning System (GPS) can be employed to reduce the error growth...
-
Analysis of free‐air anomalies on the seaway of the Gulf of Gdańsk. A case study
PublikacjaIn this paper, we present an attempt to determine the accuracy of shipborne gravimetry for the needs of geoid determination. The shipborne gravity campaign, described in this article, is the beginning of a series of gravimetry measurements in the Polish Exclusive Economy Zone. The campaign was conducted in the area where the accuracy of geoid determination is crucial for the safety of navigation on numerous intersecting ships routes....
-
Application of galvanodynamic impedance spectroscopy for studying passive film cracking under mechanical strain
PublikacjaThe paper reports the results of simultaneous mechanical and electrochemical investigations on austenitic (18/8) stainless steel in a 2 % solution of sulphuric acid. The measurements were performed using Galvanodynamic Electrochemical Impedance Spectroscopy (GDEIS). Electrochemical analysis of mechanical passive layer cracking and repassivation conditions during a tensile test was carried out. Application of this methodology allowed...
-
Detail, Facture, and Colour in the Architecture of Polish Single-Family Houses after 1989
PublikacjaThe article presents single-family houses architecture transformations since 1989, with particularly close attention paid to the significance of detail, facture, and colour. The article presents the architecture as an art of designing and building facilities with both use and aesthetic value, an art of shaping space and building forms. Architectural work should correspond to the intended function, technique, economic and aesthetic...
-
Experimental research on a hydrodynamic thrust bearing with hydrostatic lift pockets: Influence of lubrication modes on bearing performance
PublikacjaThe aim of the study is to investigate the performance of a thrust bearing equipped with hydrostatic lift pockets under different lubrication modes. Three types of flat land bearing lubrication modes are studied experimentally: hydrostatic lubrication (HS; forced oil injection to the pockets), hybrid lubrication (HS + HD; hydrostatic lubrication combined with the external forced bearing oil supply) and hydrodynamic lubrication...
-
Three electrode configuration measurements of electrolyte-diffusion barrier-cathode interface
PublikacjaMeasurements of a system consisting of cathode/doped ceria diffusion barrier/doped zirconia electrolyte were made using two- and three-electrode configuration. Results obtained on a three-electrode measurement configuration were compared with and reflect the results obtained in two-electrode configuration. Three-electrode measurements allowed separating the impact of the symmetrical interface in the investigated system. They also...
-
User-assisted methodology targeted for building structure interpretable QSPR models for boosting CO2 capture with ionic liquids
PublikacjaTask-specific ionic liquid (IL) is an emerging class of compounds that may be environmentally friendly. Properly selected, these compounds may be green alternative to amine solutions and can replace them in post-combustion carbon dioxide (CO2) capture processes on an industrial scale. However, owing to the vast diversity of ions and their possible combinations, laboratory research is time consuming and expensive. Therefore, computational...
-
Crystal structures of aminotransferases Aro8 and Aro9 from Candida albicans and structural insights into their properties
PublikacjaAminotransferases catalyze reversibly the transamination reaction by a ping-pong bi-bi mechanism with pyridoxal 5′-phosphate (PLP) as a cofactor. Various aminotransferases acting on a range of substrates have been reported. Aromatic transaminases are able to catalyze the transamination reaction with both aromatic and acidic substrates. Two aminotransferases from C. albicans, Aro8p and Aro9p, have been identified recently, exhibiting...
-
TiO2 nanotube arrays-based reactor for photocatalytic oxidation of parabens mixtures in ultrapure water: Effects of photocatalyst properties, operational parameters and light source
PublikacjaSelf-organized TiO2 nanotubes as immobilized photocatalysts were evaluated in detail for the photocatalytic degradation of parabens mixtures from ultrapure water. This kind of approach can be a very suitable option for emerging contaminants degradation considering the possibility of the catalyst reuse and recovery which will be simpler than when catalytic powders are used. The anodization method was applied for the TiO2 nanotubes...
-
Categorization of emotions in dog behavior based on the deep neural network
PublikacjaThe aim of this article is to present a neural system based on stock architecture for recognizing emotional behavior in dogs. Our considerations are inspired by the original work of Franzoni et al. on recognizing dog emotions. An appropriate set of photographic data has been compiled taking into account five classes of emotional behavior in dogs of one breed, including joy, anger, licking, yawning, and sleeping. Focusing on a particular...
-
Influence of nanoparticle concentration on thermal properties of thermal oil-MWCNT nanofluid
PublikacjaResults of the measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of thermal oil-MWCNT (TO-MWCNT) nanofluid have been presented. Nanoparticles were tested at the concentration of 0.001%, 0.005%, 0.01%, 0.05%, and 0,1% by weight. Thermal oil (TO) was selected as a base liquid, because of possible application in ORC systems as an intermediate heating agent. Multi-walled carbon nanotubes were used...
-
Hydrographic Multisensory Unmanned Watercraft
PublikacjaThis article describes the design of the unmanned surface vessel (USV) and the algorithms for planning the trajectories to be followed on measurement missions. The algorithms take account of the dynamically varying impacts of external forces (wind and surface current) on the vessel's motion. Feedback loops enable the counteraction of external factors that cause disturbance to the desired trajectory. The sensors installed on the...
-
Effects of FSW Tool Plunge Depth on Properties of an Al-Mg-Si Alloy T-Joint: Thermomechanical Modeling and Experimental Evaluation
PublikacjaOne of the main challenging issues in friction stir welding (FSW) of stiffened structures is maximizing skin and flange mixing. Among the various parameters in FSW that can affect the quality of mixing between skin and flange is tool plunge depth (TPD). In this research, the effects of TPD during FSW of an Al-Mg-Si alloy T-joint are investigated. The computational fluid dynamics (CFD) method can help understand TPD effects on FSW...
-
The influence of a change in the meniscus cross-sectional shape on the medio-lateral translation of the knee joint and meniscal extrusion
PublikacjaObjective The purpose of this study was to evaluate the influence of a change in the meniscus cross sectional shape on its position and on the biomechanics of a knee joint. Methods One main finite element model of a left knee joint was created on the basis of MRI images. The model consisted of bones, articular cartilages, menisci and ligaments. Eight variants of this model with an increased or decreased meniscus height were then...
-
A hybrid model of flooding of the ro-ro ships in damaged conditions
PublikacjaThe paper presents some results on investigations concerning development of a hybrid model for assessment of performance of the ro‐ro ships in damaged conditions. The model is devoted towards assessing the performance of the damaged ro‐ro ships at the preliminary stage of design. The key problems associated with preparing of such the model are associated with working out a method of assessment of the damaged roro ships performance,...
-
Acoustic Heating Produced in the Thermoviscous Flow of a Shear-Thinning Fluid
PublikacjaThis study is devoted to the instantaneous acoustic heating of a shear-thinningfluid. Apparent viscosity of a shear-thinning fluid depends on the shear rate. Thatfeature distinguishes it from a viscous Newtonian fluid. The special linear combi-nation of conservation equations in the differential form makes it possible to derivedynamic equations governing both the sound and non-wave entropy mode inducedin the field of sound. These...
-
Cooperative control in production and logistics
PublikacjaClassical applications of control engineering and information and communication technology (ICT) in production and logistics are often done in a rigid, centralized and hierarchical way. These inflexible approaches are typically not able to cope with the complexities of the manufacturing environment, such as the instabilities, uncertainties and abrupt changes caused by internal and external disturbances, or a large number and variety...
-
Comparative analysis of mechanical conditions in bone union following first metatarsophalangeal joint arthrodesis with varied locking plate positions: A finite element analysis
PublikacjaFirst metatarsophalangeal joint arthrodesis is a typical medical treatment performed in cases of arthritis or joint deformity. The gold standard for this procedure is arthrodesis stabilisation with the dorsally positioned plate. However, according to the authors’ previous studies, medially positioned plate provides greater bending stiffness. It is worth to compare the mechanical conditions for bone formation in the fracture callus...
-
Technical and economic analysis of energy storage in the compressed air technology with low capacity for the production plant
PublikacjaCompressed air energy storage (CAES) system is a promising technology due to its numerous advantages, including relatively low maintenance cost, a long lifespan and high operational flexibility. This article explores the possibility of designing a CAES power plant as a source of electricity and heat for an existing industrial plant. The study involves the technical analysis of the power plant parameters and the economic analysis...
-
Flow Maps and Flow Patterns of R1233zd(E) in a Circular Minichannel at Low, Medium and High Values of Saturation Pressure
PublikacjaThere is a gap in knowledge regarding the flow pattern of low-boiling working fluids in the range of high saturation temperatures (above 120°C) and medium and high reduced pressures (0.5-0.9). Data are present in the literature for similar values of reduced pressures, but for lower values of saturation temperature. This is due to the existing refrigeration applications of these working fluids. At high values of reduced pressure,...
-
Rola innowacji otwartych w klastrach
PublikacjaInnowacje otwarte to podejście, w którym korzysta się z partnerstwa i łączenia zasobów wewnętrznych i zewnętrznych wobec firmy w celu kreowania nowych pomysłów i technologii. Klastry natomiast są uznawane za przestrzeń sprzyjającą międzyorganizacyjnej współpracy innowacyjnej. Głównym celem podejmowanym w rozprawie było zbadanie roli innowacji otwartych w klastrach poprzez dokonanie diagnozy stanu i sposobu ich podejmowania oraz...
-
ANALIZA ROZKŁADU POLA MAGNETYCZNEGO WEWNĄTRZ OBIEKTU FERROMAGNETYCZNEGO
PublikacjaW artykule przedstawione zostały wyniki analizy rozkładu natężenia pola magnetycznego wewnątrz obiektu ferromagnetycznego. Obiekt ferromagnetyczny znajdujący się w zewnętrznym polu magnetycznym wywołuje jego zaburzenie, które może być podstawą do wykrycia tego obiektu. Pożądanym zatem jest, aby kompensować to zaburzenie przez zastosowanie cewek kompensujących umieszczonych wewnątrz obiektu. Analiza rozkładu natężenia pola magnetycznego...
-
Preparation and some properties of multiblock copoly(amide-b-amide)s
PublikacjaThe paper concerns the polymers built of oligoamide hard blocks and oligoamide soft blocks (KPAA, formula I). Oligo(laurolactam) (PA12) was used as hard block and the product of reaction of dimerized fatty acid and hexamethylene diamine (PA6,36) was used as a soft one. Effects of molar ratio of these blocks on the following properties of KPAA have been investigated: limiting viscosity number ([2]), degrees of swelling in water...