Filtry
wszystkich: 4477
wybranych: 2176
-
Katalog
- Publikacje 2176 wyników po odfiltrowaniu
- Czasopisma 45 wyników po odfiltrowaniu
- Konferencje 8 wyników po odfiltrowaniu
- Wydawnictwa 1 wyników po odfiltrowaniu
- Osoby 205 wyników po odfiltrowaniu
- Wynalazki 21 wyników po odfiltrowaniu
- Projekty 29 wyników po odfiltrowaniu
- Laboratoria 1 wyników po odfiltrowaniu
- Aparatura Badawcza 5 wyników po odfiltrowaniu
- Kursy Online 140 wyników po odfiltrowaniu
- Wydarzenia 76 wyników po odfiltrowaniu
- Dane Badawcze 1770 wyników po odfiltrowaniu
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: SOFC, SOEC, INTERCONNECORS, MCO, COATINGS
-
FLUID BED COATING OF MINITABLETS AND PELLETS WITH OPTIMIZATION OF THE PROCESS BASED ON TAGUCHI METHOD
PublikacjaSmall particles like pellets are coated in fluid bed systems. This method can be also feasible for minitablets but the selection of optimal process parameters is complicated. The aim of the research was to optimize the coating process for minitablets and to compare the conditions required for pellets. Minimum fluidization velocities (umf) for 2.0 and 2.5 mm minitablets and 0.7-0.8 mm or 1.0-1.25 mm pellets were determined experimentally....
-
Effect of microstructure on mechanical properties of BA1055 bronze castings
PublikacjaThe article presents research results performed on aluminum bronze CuAl10Fe5Ni5 (BA1032) castings used for marine propellers. Metallographic studies were made on light microscope and a scanning electron microscope to assess quantitatively and qualitatively the alloy microstructure. It has been shown that the shape, size and distribution of the iron-rich phase precipitates in bronze microstructure significantly affect its mechanical...
-
Wpływ zawartości grafitu na właściwości mechaniczne warstw hybrydowych Ni-P/Si3N4/grafit osadzonych na stopie AW-7075 metodą redukcji chemicznej.
PublikacjaPrzedstawiono wpływ obecności grafitu jako fazy dyspersyjnej na właściwości mechaniczne warstw hybrydowych Ni-P/Si3N4/grafit, które osadzono metodą redukcji chemicznej na stopie glinu AW-7075. Wykonano badania morfologii powierzchni warstw metodą mikroskopii świetlnej i skaningowej. Dalszą część pracy stanowiły badania mechaniczne, czyli pomiary mikrotwardości warstw oraz ich adhezji do aluminiowego podłoża, a także analizy wpływu...
-
Mechanical and physical assessment of epoxy, mineral, solvent-based, and water-soluble coating materials
PublikacjaThis paper assesses the behavior of mineral, epoxy (EP), solvent, and water-soluble coatings when exposed to salt and regular water for 28 days. Also, it evaluates the pull-off adhesion strength of the same coating materials applied to concrete slabs saturated with oil and water and dried with two different processes: air-dried for 28 days and air-dried for 14 days plus 14 days in the oven at 70 °C. Properties such as carbonation,...
-
The effect of hard/soft segment composition on radiation stability of poly(ester-urethane)s
Publikacja -
Carbon Deposition and Sulfur Poisoning in SrFe0.75Mo0.25O3-δand SrFe0.5Mn0.25Mo0.25O3-δElectrode Materials for Symmetrical SOFCs
Publikacja -
The influence of changes of soil parameters due to consolidation on the interaction of piles and soft soil layer
PublikacjaZaprezentowano problem wyznaczania bocznego parcia gruntu o małej wytrzymałości na pale. Opisano przypadki występowania bocznego obciążenia pali. Scharakteryzowano właściwości i zachowanie gruntów słabych stanowiących warstwę podłoża o małej wytrzymałości. Zaprezentowano propozycje obliczania bocznego parcia według różnych autorów. Przedstawiono wpływ konsolidacji na zmianę wytrzymałości gruntów słabych w czasie oraz na obliczanie...
-
Fabrication methods of porous perovskite type ceramics for Solid Oxide Fuel Cells (SOFCs)
PublikacjaPublikacja opisuje metody wytwarzania porowatych materiałów ceramicznych o strukturze perowskitu.
-
Influence of plastic deformation on stray magnetic field distribution of soft magnetic steel sample
PublikacjaThe effect of various combinations of conditions, i.e., presence of the Earth’s magnetic field during and after deformation on the distribution of stray magnetic field of S355 steel sample, which is locally deformed, was investigated. Some of the stages of the experiment were carried out in zero magnetic field. Compensation of the Earth’s magnetic field was obtained by the application of a pair of Helmholtz coils. These coils are...
-
SEI Growth and Depth Profiling on ZFO Electrodes by Soft X-Ray Absorption Spectroscopy
PublikacjaZnFe2O4 (ZFO) Li-ion batteries (LIBs) represent a reliable, affordable, and safe energy storage technology for use in portable application. However, current LIB active materials (graphite, lithium/transition metal spinel or layered oxides, olivine structures) can store only limited energy since they rely on insertion storage based on solid-state host-guest interactions. Moreover, performances and durability of the cells are strongly...
-
Microstructure and electrical properties of SrTi0.98Nb0.02O3-δ-based composites applied as porous layers for SOFCs
PublikacjaPrzebadano właściwości elektryczne oraz strukturalne kompozytów Sr(Ti,Nb)O3-YSZ i Sr(Ti,Nb)O3-CeO2 naniesionych w postaci warstw porowatych na podłoża YSZ
-
A Proposed Soft Computing Model for Ultimate Strength Estimation of FRP-Confined Concrete Cylinders
PublikacjaIn this paper, the feed-forward backpropagation neural network (FFBPNN) is used to propose a new formulation for predicting the compressive strength of fiber-reinforced polymer (FRP)-confined concrete cylinders. A set of experimental data has been considered in the analysis. The data include information about the dimensions of the concrete cylinders (diameter, length) and the total thickness of FRP layers, unconfined ultimate concrete...
-
Structural and catalytic properties of ceria layers doped with transition metals for SOFCs fueled by biogas
PublikacjaThe aim of this paper was to investigate an influence of the nanocrystalline Ce0.8A0.2O2-δ (A = Mn, Fe, Co, Ni, Cu) materials on the direct internal reforming of biogas in SOFC. Structural analysis of fabricated compounds has been done. An in-situ analysis of a composition of outlet gases from operating SOFC was performed using FTIR spectroscopy with simultaneous electrical tests. It was found out, that type of dopant strongly...
-
Large deformation modelling of CPT probing in soft soil—pore water pressure analysis
PublikacjaThis paper presents the results of finite element modelling with Updated Lagrangian formulation of the Cone Penetration Test in soft soil deposit located in Jazowa, Poland. The numerical calculations are carried out for homogenous, normally consolidated, organic soil layer. The Modified Cam Clay constitutive model for soft soil and Coulomb model for interface are used. The study compares the registered pore water pressure distributions...
-
Wykorzystanie fourierowskiej spektroskopii w podczerwieni do badania stężenia gazów wylotowych z tlenkowego ogniwa paliwowego zasilanego biogazem
PublikacjaW dzisiejszych czasach bardzo ważne jest pozyskiwanie energii ze źródeł odnawialnych i bezpiecznych dla środowiska. Jedną z obiecujących technologii są tlenkowe ogniwa paliwowe (ang. Solid Oxide Fuel Cell, SOFC). Stanowią one bezpieczną i ekologiczną alternatywę dla energii uzyskanej z paliw kopalnych. SOFC charakteryzuje się sprawnością energetyczną na poziomie 45-60 %, podczas gdy sprawność klasycznych elektrowni cieplnych nie...
-
Sustainable energy system combined biogas-feedSolid Oxide Fuel Cell and Microalgae technology
PublikacjaIn the new frontier of energy and environmental safety, new efficient and clean safe energy conversion systems are required. In this sense, the present work is framed within the context of Circular Economy and proposes a multidisciplinary study for the development of more efficient, economically viable and non-polluting energy conversion systems, based on the synergetic combination of different technologies: fuel cells, biofuels,...
-
Effects of electrophoretic deposition times and nanotubular oxide surfaces on properties of the nanohydroxyapatite/nanocopper coating on the Ti13Zr13Nb alloy
PublikacjaLoad-bearing implants are developed with a particular emphasis placed on an application of ceramic hydroxyapatite coatings in order, to enhance the bioactivity of titanium implants and to shorten the healing time. Therefore, thin, fully crystalline coatings that are, highly adhesive, hydrophilic and demonstrating antibacterial properties are ly looked for. The aim of this research was to develop and characterize the properties...
-
The mediational role of future and past time perspectives in the relationship between negative affectivity and sense of coherence
PublikacjaSense of coherence (SoC) can promote positive coping, and one of its most prominent negative correlates is negative affectivity (NA). In the current study, we hypothesized that future and past time perspectives (TPs) will mediate the relationship between sense of coherence and negative affectivity, and the inverse relationship. The study was questionnaire-based, performed online. N = 719 participants aged 25-45 from...
-
High-performance NdSrCo2O5+δ–Ce0.8Gd0.2O2-δ composite cathodes for electrolyte-supported microtubular solid oxide fuel cells
PublikacjaNdSrCo2O5+δ (NSCO) is a perovskite with an electrical conductivity of 1551.3 S cm−1 at 500 °C and 921.7 S cm−1 at 800 °C and has a metal-like temperature dependence. This perovskite is used as the cathode material for Ce0.8Gd0.2O2-δ (GDC)-supported microtubular solid oxide fuel cells (MT-SOFCs). The MT-SOFCs fabricated in this study consist of a bilayer anode, comprising a NiO–GDC composite layer and a NiO layer, and a NSCO–GDC...
-
Preparation and evaluation of solid-phase microextraction fibres based on functionalized latex nanoparticle coatings for trace analysis of inorganic anions
Publikacja -
Metoda badania powłok ceramicznych w ruchu postępowo-zwrotnym = A method for testing of ceramic coatings under reciprocating sliding
PublikacjaOpracowano metodę badania powłok ceramicznych w warunkach tarcia ślizgowego na próbkach tworzących układ o styku niekonforemnym kula - powierzchnia płaska. Pokryte warstwą ceramiczną kule dociskano do próbek płaskich - prostopadłościennych listew (również pokrytych ceramiką), wykonujących ruch postępowo-zwrotny. Jako stanowisko badawcze zastosowano Tribometr Posuwisto-zwrotny TPZ-1. Przebieg zużywania się powłoki ceramicznej oceniano...
-
Friction and wear behaviour of self mated DLC and DLC-W coatings in water or salt in water solution lubricated sliding
PublikacjaPrzedstawiono wyniki badań powłok ceramicznych DLC oraz DLC z wolframem (DLC-W) nałożonych na podłoże ze stali nierdzewnej,przy tarciu ślizgowym , w modelowym skojarzeniu o styku konforemnym (płaskie czoło obracającej się względem swojej osi tulei - powierzchnia płaska). Badania prowadzono stosując smarowanie wodą destylowaną albo wodnym roztworem soli - NaCl. Wyznaczano współczynniki tarcia oraz intensywność zużywania ceramicznej...
-
Tailoring optical constants of few-layer black phosphorus coatings: Spectroscopic ellipsometry approach supported by ab-initio simulation
Publikacja2D black phosphorus (BP) has attracted extensive attention as an anisotropic platform for novel optoelectronic and polarizing optics applications. Insight into the factors that tune the optical and polarizing properties of 2D BP reveals their essential influence on BP-based photonic and optoelectronic devices. In this work, studies of the optical constants of few-layer black phosphorus coatings are studied and discussed, with particular...
-
Anisotropic optical properties of few-layer black phosphorus coatings: from fundamental insights to opto-electrochemical sensor design
PublikacjaFew-layer black phosphorus (FLBP) is characterised by a tuneable bandgap, high carrier mobility and anisotropic optical properties. It therefore has the potential to find applications in electronics and photonics. FLBP oxidizes upon exposure to air, limiting its utility in devices and components. To address this issue, the thesis introduces methods and tools developed for studying FLBP's optical parameters, with a particular emphasis...
-
Bulk processing of ZnO nanostructures via microwave assisted oxidation of mechanically seeded Zn dust for functional paints and coatings
Publikacja -
The Effect of Surface Modification of Ti13Zr13Nb Alloy on Adhesion of Antibiotic and Nanosilver-Loaded Bone Cement Coatings Dedicated for Application as Spacers
PublikacjaSpacers, in terms of instruments used in revision surgery for the local treatment of postoperative infection, are usually made of metal rod covered by antibiotic-loaded bone cement. One of the main limitations of this temporary implant is the debonding effect of metal–bone cement interface, leading to aseptic loosening. Material selection, as well as surface treatment, should be evaluated in order to minimize the risk of fraction...
-
The abrasive wear resistance of coatings manufactured on high-strength low-alloy (HSLA) offshore steel in wet welding conditions
PublikacjaSome marine and offshore structure elements exploited in the water cannot be brought to the surface of the water as this will generate high costs, and for this reason, they require in-situ repairs. One of the repair techniques used in underwater pad welding conditions is a wet welding method. This paper presents an investigation of the abrasive wear resistance of coatings made in wet welding conditions with the use of two grades...
-
Ionogel sorbent coatings for determining organophosphorus and pyrethroid insecticides in water and fresh juice samples by headspace-solid phase microextraction
PublikacjaThe sol–gel method yielded three different ionogel sorbent coatings that were obtained based on a silica material containing ionic liquids (ILs) immobilized in its pores. Two ILs, triethylsulfonium bis(trifluoromethylsulfonyl) imide [Set3][TFSI] and 1-butyl-1-methylpiperidinium bis(trifluoromethylsulfonyl)imide [C4C1Pip][TFSI], as well as their equimolar mixture [Set3/C4C1Pip], were used to obtain ionogel fibers. The developed...
-
Zastosowania chromatografii wykluczania (SEC) w analityce technicznej i preparatyce – część I-sza.
PublikacjaW pracy scharakteryzowano założenia teoretyczne oraz mechanizm rozdzielania w warunkach chromatografii wykluczania (SEC). Przeanalizowano wady i zalety tej techniki rozdzielania. Przedstawiono przegląd zastosowań obejmujący wykorzystanie SEC w analityce technicznej oraz w preparatyce. SEC w warunkach liofilowych znajduje zastosowanie do rozdzielania mieszanin polimerów t.j. polistyren, polibutadien, poliizopren, poli(dimetylosiloksan),...
-
Drug-Releasing Antibacterial Coating Made from Nano-Hydroxyapatite Using the Sonocoating Method
Publikacja -
Advanced coating of interior of tanks for rising environmental safety of tankers - novel applications of polyurethanes
PublikacjaOpisano technologię nanoszenia ciekłego systemu poliuretanowego na niewygrzewane elementy stalowe i stalowo-betonowe oraz sposób łączenia powłoki poliuretanowej z wymienionymi materiałami, a także między sobą przy użyciu odpowiednich środków adhezyjnych. Scharakteryzowano metodę utylizacji i odzysku polioli z zużytych w badaniach powłok poliuretanowych w recyklingu surowcowym poprzez zastosowanie małoczšsteczkowych glikoli jako...
-
The Effect of Texturing of the Surface of Concrete Substrate on the Pull-Off Strength of Epoxy Resin Coating
Publikacja -
Biopolymers based paper coating with promoted grease resistivity, bio-degradable and mechanical properties
Publikacja -
Advanced coating of Tank Interior as means of Rising Environmental Safety of Tankers/RIM technology
Publikacja -
Chapter 13 : The influence of dispersion phase on composite coating properties after cold working
PublikacjaW pracy określono wpływ fazy dyspersyjnej Al2O3 na wybrane potencjalne właściwości powłok kompozytowych o osnowie niklowej. Powłoki Ni-Al-Al2O3 zostały nałożone na próbki stalowe przy użyciu technologii poddźwiękowego płomieniowego natryskiwania cieplnego. Następnie poddane zostały obróbce plastycznej na zimno i na gorąco poprzez walcowanie, a także prasowania na zimno na prasie hydraulicznej. Obróbka plastyczna jest metodą alternatywną...
-
Influence of porous coating on heat transfer during flow boiling of R22, R134a and R407C
PublikacjaPrzedstawiono wpływ pwłoki porowatej w pozionej rurce podczas wrzenia w przepływie i spadku ciśnienia czynników chłodniczych R22, R134a i R407C.
-
Anticorrosive and antimicrobial efficiency of photopolymerizable phosphorus (meth)acrylate oligomers-based coating materials
Publikacja -
The effect of the ceramic dispersion on the nickel matrix composite coating properties after plastic working
PublikacjaW pracy określono wpływ fazy dyspersyjnej Al2O3 na wybrane potencjalne właściwości powłok kompozytowych o osnowie niklowej. Powłoki Ni-Al-Al2O3 zostały nałożone na próbki stalowe przy użyciu technologii poddźwiękowego płomieniowego natryskiwania cieplnego. Następnie poddane zostały obróbce plastycznej na zimno i na gorąco poprzez walcowanie, a także prasowania na zimno na prasie hydraulicznej. Obróbka plastyczna jest metodą alternatywną...
-
Damage tests of the single shell ship fuel tank with additional elastic protective coating
PublikacjaWejście na mieliznę lub kolizja średniej wielkości np. kontenerowca może doprowadzić do zanieczyszczenia środowiska Morza Bałtyckiego paliwem uwolnionym z rozszczelnionych, jednoposzyciowych zbiorników dennych, a ilość tego paliwa może być znaczna. W związku z tym podjęto prace badawcze zmierzające do opracowania sposobu obniżenia ryzyka rozlewu paliwa w wypadku kolizji poprzez wprowadzenie drugiej bariery ochronnej. Idea pomysłu...
-
Multispectral impedance quality testing of coil-coating system using principal component analysis
PublikacjaThe task of quality checking of the coil-coated system was undertaken using impedance spectroscopy. In order to properly characterize the system the new impedance spectrum was calculated as an averaged result of 12 experimental spectra obtained from 12 different places of the sample at the same time of immersion in 3% of NaCl. The experimental spectra were recorded for a 24-h period at 1 h intervals between starting points of each...
-
Strontium-based nanosized phosphates as anticorrosive fi llers of epoxy and polyurethane coating compositions
PublikacjaAnticorrosive epoxy and polyurethane coatings were compounded using zinc-free nanosized phosphates of strontium (SP) or strontium and aluminum (SAP). For comparison, a nanosized calcium aluminum ammonium phosphate (CAP) and a microsized zinc phosphate (ZP) were tested. Results of salts spray and cyclic corrosion tests revealed better anticorrosive properties of the SAP-based coatings...
-
Improved surface coverage of an optical fibre with nanocrystalline diamond by the application of dip-coating seeding
PublikacjaGrowth processes of diamond thin films on the fused silica optical fibres (10 cm in length) were investigated at various temperatures. Fused silica pre-treatment by dip-coating in a dispersion consisting of detonation nanodiamond (DND) in dimethyl sulfoxide (DMSO) with polyvinyl alcohol (PVA) was applied. Nanocrystalline diamond (NCD) films were deposited on the fibres using the microwave plasma assisted chemical vapour deposition...
-
Multivariate analysis of impedance data obtained for coating systems of varying thickness applied on steel
PublikacjaElectrochemical impedance spectroscopy (EIS) has proven to be a valuable test method for the electrochemical characterization of protective coatings on metals. The common way of analysis in impedance spectroscopy is to model the impedance spectrum by means of an equivalent circuit and to extract the quantity of interest using optimization techniques. A model, corresponding to the behavior of the sample under testing, is important...
-
Elastic protection coating for ship fuel tanks, intended for the increasing of environment protection level
PublikacjaW opracowaniu przedstawiono problemy związane z wprowadzeniem nowego rozwiązania dla podniesienia bezpieczeństwa zbiorników paliwowych, poprzez zainstalowanie we wnętrzu zbiornika drugiej elastycznej bariery ochronnej opartej na warstwie wypełniacza. Przedstawiono wyniki prac związanych z doborem parametrów warstwy drugiej bariery jak również materiału wypełniacza.
-
Applications of spin coating of polymer precursor and slurrysuspensions for Solid Oxide Fuel Cell fabrication
PublikacjaW pracy przedstawiono możliwości zastosowania w tlenkowych ogniwach paliwowych metody nanoszenia wirowego prekursorów polimerowych i zawiesin. Przedstawiono przykłady zastosowania tej metody do wytworzenia elektrolitu oraz warstw ochronnych dla stali nierdzewnych.
-
Drop-coating deposition surface-enhanced Raman spectroscopy on silver substrates for biofluid analysis
PublikacjaUtilization of surface-enhanced Raman spectroscopy as a measurement technique is of particular interest in biodetection due to its superb chemical specificity and high sensitivity. The use of SERS substrates further improve this method by massive enhancement of the molecule Raman spectrum, permitting very low levels of detection. Therefore it is important to seek for new ways to develop reliable substrates, which are quickly and...
-
Evaluation of organic coating systems for corrosion protection of industrial equipment using impedance spectroscopy
PublikacjaThe high economic impact of corrosion can be reduced by enhanced corrosion management and prevention based on appropriate means. This applies in particular to the protection of structures with organic protective coatings. Steel is subject to corrosion that reduces its service life and leads to destruction in most severe cases. The application of paints to metallic objects for corrosion control has been known for a long time and...
-
Optical-Fiber Microsphere-Based Temperature Sensors with ZnO ALD Coating—Comparative Study
PublikacjaThis study presents the microsphere-based fiber-optic sensor with the ZnO Atomic Layer Deposition coating thickness of 100 nm and 200 nm for temperature measurements. Metrological properties of the sensor were investigated over the temperature range from 100 °C to 300 °C, with a 10 °C step. The interferometric signal was used to monitor the integrity of the microsphere and its attachment to the connecting fiber. For the sensor...
-
Functional fluorine-doped tin oxide coating for opto-electrochemical label-free biosensors
PublikacjaSensors operating in multiple domains, such as optical and electrochemical, offer properties making biosensing more effective than those working in a single domain. To combine such domains in one sensing device, materials offering a certain set of properties are required. Fluorine-doped tin oxide (FTO) thin film is discussed in this work as functional optically for guiding lossy modes and simultaneously electrochemically, i.e....
-
Using impedance spectroscopy to characterize and monitor protection aspects of organic coating systems on metal
PublikacjaOrganiczne powłoki ochronne stosowane są powszechnie do ochrony konstrukcji metalowych przed korozją i zużyciem mechanicznym. W pracy zaproponowano nowy typ sensora impedancyjnego, który może być zastosowany do ciągłej oceny właściwości barierowych i adhezyjnych systemów powłokowych w warunkach terenowych w sposób nieniszczący, bez konieczności stosowania naczyń z elektrolitem. Przedstawiono koncepcję czujnika oraz przykładowe...