Filtry
wszystkich: 5269
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: PHOTOELECTROCHEMICAL PROPERTIES
-
Biological and mechanical properties of bone cement with nanoparticles - in vivo and in vitro research
PublikacjaDespite antibiotics preventive treatment, before and after an implant implementation, risk of infection are real. These infections at the implant surface develop in a few months after applying them into the body. To prevent the development of bacteria and to reduce the risk of infection, implants coated with nanoparticles come into use. The Mechanical Department of the Technical University of Gdańsk carried out a research with...
-
A COMPARISON OF WEAR PROPERTIES OF WATER LUBRICATED NBR AND PTFE SLIDING BEARINGS
PublikacjaThe excessive wear of a journal shaft can be caused by many factors, for example, working conditions (e.g., temperaturę, slip speed, the type of lubricant), pressure, the type of material used on the bearings and shafts and their roughness, as well as contamination remaining in the system. This paper presents the roughness profiles co-operating with a rubber (NBR) and polytetrafluoroethylene (PTFE) bushes. The conditions of cooperation...
-
Effects of Na+, K+ and B3+ Substitutions on the Electrical Properties of La10Si6O27 Ceramics
PublikacjaDoping of Na and K at La sites and of B at Si site in La10Si6O27 with oxyapatite structure and fabrication of their ceramics were made by the solid-state reaction method. It was found that partial substitution of Na+ and K+ on La sites decreased the sinterability of the La10Si6O27 based ceramics, whereas partial substitution of B3+ on the Si site improved the sinterability. Na+ and K+ substitutions in La10−xNaxSi6O27−x and La10−xKxSi6O27−x...
-
Study of nanomechanical properties of (1-y)BST-yMgO thin films
PublikacjaIn the present study thin films of MgO – modified Ba0.6Sr0.4TiO3 (BST60/40) solid solution were prepared by the sol-gel-type chemical solution deposition method on stainless steel substrates. A multilayer spin-coating approach was utilized for the Ba0.6Sr0.4TiO3-MgO thin film deposition with subsequent thermal annealing at T=650-750C. Dried BST60/40-MgO gel powders were studied with thermogravimetric and differential thermal analysis...
-
Effects of Na+, K+ and B3+ Substitutions on the Electrical Properties of La10Si6O27 Ceramics
PublikacjaDoping of Na and K at La sites and of B at Si site in La10Si6O27 with oxyapatite structure and fabrication of their ceramics were made by solid-state reaction method. It was found that partial substitution of Na+ and K+ on La sites decreased the sinterability of the La10Si6O27 based ceramics, whereas partial substitution of B3+ on Si site imporved the sinterability. Na+ and K+ substitutions in La10-xNaxSi6O27-x and La10-xKxSi6O27-x...
-
Comparison of Properties of the Hybrid and Bilayer MWCNTs—Hydroxyapatite Coatings on Ti Alloy
PublikacjaCarbon nanotubes are proposed for reinforcement of the hydroxyapatite coatings to improve their adhesion, resistance to mechanical loads, biocompatibility, bioactivity, corrosion resistance, and antibacterial protection. So far, research has shown that all these properties are highly susceptible to the composition and microstructure of coatings. The present research is aimed at studies of multi-wall carbon nanotubes in three different...
-
Influence of Sn and Pb Ions Substitutions on Dielectric Properties of Barium Titanate
PublikacjaThe results of the microstructural and dielectric measurements of (Ba1-xPbx)(Ti1-xSnx)O3 (BPTSx) (x = 0, 0.05, 0.10, 0.30) polycrystalline samples are presented. The samples were obtained by means of a high temperature synthesis and their expected stoichiometry was confirmed by energy dispersive spectroscopy (EDS) measurements. The dielectric properties of BPTSx were studied with the use of broadband dielectric spectroscopy. The...
-
AN ALTERNATIVE WAY OF DETERMINING MECHANICAL PROPERTIES OF WOOD BY MEASURING CUTTING FORCES
PublikacjaThe cutting force is an energetic effect of splitting material, and might be therefore considered from a point of view of modern fracture mechanics. The dedicated mathematical model developed for description of the wood cutting has been developed here on the base of fracture theory, and includes work of separation (fracture toughness) in addition to the material plasticity and friction. The effect of the cutting edge dullness is...
-
Antimicrobial properties of chitosan solutions, chitosan films and gelatin-chitosan films
PublikacjaThe antimicrobial properties of chitosan solutions and films against selected bacteria and the effect of chitosan incorporation into gelatin films were studied. The bactericidal effect of chitosan solutions increased with time and temperature of sample incubation. Two psychrotrophic strains Pseudomonas fluorescens and Listeria innocua were more sensitive to chitosan than mesophilic strains Escherichia coli and Staphylococcus aureus....
-
SAWING PROCESS AS A NEW ALTERNATIVE WAY OF DETERMINING SOME WOOD PROPERTIES
PublikacjaCutting forces (power) could be considered from a point of view of modern fracture mechanics. The developed cutting model, derived from fracture mechanics, includes work of separation (fracture toughness) in addition to plasticity and friction, and also dullness of the cutting edge described by the cutting edge radius. Moreover, forecasting of the shear plane angle for the cutting models, broaden possibilities of energetic effects...
-
Periodic Properties of 1D FE Discrete Models in High Frequency Dynamics
PublikacjaFinite element discrete models of various engineering 1D structures may be considered as structures of certain periodic characteristics. The source of this periodicity comes from the discontinuity of stress/strain field between the elements. This behaviour remains unnoticeable, when low frequency dynamics of these structures is investigated. At high frequency regimes, however, its influence may be strong enough to dominate calculated...
-
Photovoltaic properties of cadmium selenide–titanyl phthalocyanine planar heterojunction devices
PublikacjaPhotovoltaic phenomenon taking place in cadmium selenide (CdSe)/titanyl phthalocyanine (TiOPc) planar heterojunction devices is described. Mechanisms of free charge carrier generation and their recombination in the dark and under illumination are analyzed, chosen photovoltaic parameters are presented.
-
Structure and properties of liquid Al–Cu alloys: Empirical potentials compared
PublikacjaWe report on the structure and mass transport properties of liquid Al–Cu alloys predicted by two recently-developed empirical many-body potentials: MEAM (Jelinek et al., 2012) and EAM-ADP (Apostol and Mishin, 2011), and by the well-known Gupta potential. Total and partial pair correlation functions, angular distribution functions, densities, coordination numbers and self-diffusion coefficients are compared with published experimental...
-
Emulsifi ers from renewable materials: an eco-friendly synthesis and properties
PublikacjaThe focus of this study was the preparation of novel bio based polyglycerol emulsifiers characterized by a one pot synthesis, thus by modified properties with respect to interfacial activity and effectiveness as emulsion stabilizers. The final products of the esterification process, carried out in the presence of carboxylates were used directly as emulsifiers (without purification or fractionation). Polyglycerol emulsifiers obtained...
-
Effect of Coating Material Properties on Tilting-pad Thrust Bearing Performance
PublikacjaPolymer lined tilting-pad bearings demonstrate many advantages over traditional bearing systems. Bearings with a polymer layer in comparison with a babbitted layer show, for example: lower value of friction coefficient (important during start/stops), higher fatigue strength of the coating, better distribution of the load on individual pads due to lower elasticity of the polymers, wider range of operational temperatures or the ability...
-
Preparation, composition and properties of fish silage produced with post-coagulation sludge
PublikacjaPost-coagulation sludge was added to fish fydrolyzates (silage). Silage was prepared using whole sprats. Technology of the process has been modified and sulphuric acid was replaced with phosphoric acid. The objective was to evaleuate the quality of produced silage during storage, particulary the changes of peroxide value and amount of free acids in silage fat.
-
The external walls of a passive building: A classification anddescription of their thermal and optical properties
PublikacjaThis paper attempts a new classification of insulating materials from the perspective of their utility in thepro-ecological passive construction industry. The main criterion is the conductivity of thermal and solarenergy. Based on their ability to conduct or block fluxes of thermal and solar energy, six types of insulatingwalls are proposed. On the basis of this criterion there are traditional dividing walls (typical walls, wallinsulating...
-
MECHANICAL PROPERTIES OF BOTTOM ASH – DREDGED MATERIAL MIXTURES IN LABORATORY TESTS
PublikacjaBottom ash from EC Gdańsk and dredged material taken from the mouth of The Vistula were mixed to form an engineering material used for dike construction. Mixtures with different bottom ash content were tested in laboratory to determine its basic physical and mechanical properties. The optimum bottom ash–dredged material mixture, built in the corps of the test dike, contains 70% of ash. The optimum bottom ash content in the mixture...
-
Electrical properties of Y0.08Sr0.92Ti0.92Nb0.08O3-δ after reduction in different reducing conditions
PublikacjaElectrical properties of perovskite Y0.08Sr0.92Ti0.92Nb0.08O3−ı after reduction in different conditions were studied. Relatively high electrical conductivity in samples reduced in ammonia was observed. The conductivity of Y0.08Sr0.92Ti0.92Nb0.08O3−ı reduced in ammonia at 1500 ◦C was of about 600 S/cm at 200 ◦C. Conductivity after reduction in ammonia at 1500 ◦C was stable both in hydrogen and oxygen atmosphere up to 600 ◦C. Reduction...
-
Mechanical properties of polyvinyl chloride-coated fabric under cyclic tests
PublikacjaThe aim of the present paper is to propose a method of laboratory tests necessary for the identification of mechanical properties of the coated fabric. The material parameters of the coated fabric AF 9032 are specified on the basis of the uniaxial and biaxial tensile tests. For the identification process, the techniques based on the least squares methods are used. Additionally, the uniaxial and biaxial cyclic tests are performed...
-
Influence of the internal electrolyte composition on amperometric sulphur dioxide sensor properties
PublikacjaIn this work investigation of an amperometric sulphur dioxide sensor with a liquid electrolyte, a mercury sulphate reference electrode and solid polymer electrolyte (Nafion) covered with gold as a working electrode properties is presented. The main goal of this research is to determine the influence of internal electrolyte composition on the sensor properties. Sensor filled with 1M and 5M sulphuric acid has been studied.
-
Microstructural and electrical properties of Y0:07Sr0:93−xTiO3− perovskite ceramics
PublikacjaIn order to find a relationship between electrical and microstructural properties, yttrium-doped strontium titanate (7 mol%) with various values of strontium nonstoichiometry was investigated and shown in this work. It has been observed that yttrium doping can affect the electrical properties of SrTiO3 to a great extent. Moreover, the microstructural and electrical properties can be influenced by strontium nonstoichiometry. The...
-
Numerical analysis of mechanical properties of an infill structure used in 3D printings
PublikacjaThe paper presents results of a numerical analysis focused on an identification of mechanical properties of an element created by using Fused Deposition Modelling additive manufacturing technique (FDM). There is presented a description of technology of the 3D printing, numerical model created by using the finite element method (FEM), as well as some problems referred to estimation of the mechanical properties of the printout. The...
-
Structural and electrical properties of Cr-doped SrTiO 3 porous materials
PublikacjaSeries of single-phase materials with assumed formula SrTi1−xCrxO3 (where x = 0, 1, 4, 6 mol.%) were obtained by sol-gel method. The structure and microstructure of materials were characterised by X-ray diffraction and scanning electron microscopy methods. Moreover, the study of electrical properties and evaluation of chemical stability in CO2/H2O atmosphere was performed by electrochemical impedance spectroscopy and thermogravimery...
-
Electrical properties of Na2O-CaO-P2O5 glasses doped with SiO2 and Si3N4
PublikacjaSodium-calcium-phosphate glasses doped with SiO2 or Si3N4 having similar sodium ion concentrations were prepared by melt quenching. The conductivity was measured by impedance spectroscopy under nitrogen atmosphere in a wide frequency range (10 mHz–1 MHz) and wide temperature range (153–473 K). At 36.6 °C, DC conductivities of all glasses vary between 1.1 ∗ 10−12 and 8.9 ∗ 10−12 S cm−1 and have similar activation energies (between...
-
Effect of Semiconductor Element Substitution on the Electric Properties of Barium Titanate Ceramics
PublikacjaThe investigated ceramics were prepared by a solid-state reaction from simple oxides and carbonates with the use of a mixed oxide method (MOM). The morphology of BaTi0.96Si0.04O3 (BTSi04) ceramics was characterised by means of a scanning electron microscopy (SEM). It was found that Si+4 ion substitution supported the grain growth process in BT-based ceramics. The EDS results confirmed the high purity and expected quantitative composition...
-
Rigid polyurethane foams with different flame retardants and their physical and mechanical properties
PublikacjaRigid polyurethane foams (PUFs) containing 3, 6 or 9 % of one of of two selected fire retardants (FR): oligomeric ethyl ethylene phosphate (Fyrol PNX) and expandable graphite (EG) were prepared, inspected and compared to foam without that fillers as the control. The thermal stability of PUFs was described by horizontal test according to norm: UL 94 HB. Compressive strength and physical properties (density, fragility and water absorption)...
-
Influence of anodes fabrication conditions on properties of solid oxide fuel cells
PublikacjaW pracy zamieszczono wyniki badań tlenkowych ogniw paliwowych różniących się warunkami przygotowania anody. Poszczególnego ogniwa różniły się ciśnieniem ściskania, temperaturą spiekania i składem anody.
-
Structural properties of hypothetical CeBa2Cu3O7 compound from LSDA+DMFT calculations
PublikacjaThe hypothetical stoichiometric CeBa2Cu3O7 (Ce123) compound, which has not been synthesized as a single phase yet, was studied by the density functional theory (DFT). We utilized a method which merges the local spin density approximation (LSDA) with the dynamical mean-field theory (DMFT) to account for the electronic correlations. The LSDA+DMFT calculations were performed in the high-temperature range. The particular emphasis was...
-
Structural and Transportation Properties of Strontium Titanate Composites with Ion Conductive Oxides
PublikacjaThis paper has been written based on the author’s doctoral dissertation “Structural and transportation properties of strontium and titanate composites with ion conductive oxides”, prepared under the supervision of Prof. Dr. Hab. Eng. Bogusław Kusz at the Department of Solid State Physics of Gdańsk University of Technology. It reports the idea of the thesis and conclusions from the study. Niobium doped strontium titanate (Sr(Ti,Nb)O3)...
-
Thermal and Mechanical Properties of Microporous Polyurethanes Modified with Reduced Graphene Oxide
PublikacjaMicroporous polyurethanes (MPU) were modified by adding 0.25%–1.25 wt% of reduced graphene oxide (RGO). The materials were prepared without solvent via in situ polymerization. From a technological point of view, it is very important to obtain functional materials by using reacting compounds only. The thermal characteristics of obtained MPU were investigated using TGA, DSC, and DMA techniques. In comparison to nonmodified microporous...
-
Enhanced photocatalytic properties of lanthanide-TiO2 nanotubes: An experimental and theoretical study
PublikacjaA series of Er-, Yb-, Ho-, Tb-, Gd-, Pr-TiO2 nanotubes (RE-NTs) was prepared via an electrochemical method. The as-prepared photocatalysts were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), UV–vis absorption, scanning electron microscopy (SEM) and luminescent spectroscopy. The experiments demonstrated that toluene in the gas phase was successfully degraded under visible light (LEDs λmax = 465...
-
Signal conditioning for examination of shallow-water acoustic noise correlation properties
PublikacjaThe article describes the process of signal conditioning for examination of acoustic noise correlation properties in shallow water. Knowledge of these properties is very important for the design processes of passive and active hydroacoustic systems. This paper focuses on the above issue from the point of view of passive sonar. In sonar systems, signal processing algorithms operate on both useful acoustic signals, and accompanying...
-
Synthesis, microstructure and electrical properties of nanocrystalline calcium doped lanthanum orthoniobate
PublikacjaThe single phase lanthanum orthoniobate with tetragonal structure has been synthesized by the means of mechanosynthesis method. The studies have shown the crystal structure of La0.98Ca0.02NbO4 depends on the synthesis stage. The samples were predominantly in the tetragonal phase with a trace amount of the monoclinic phase. The SEM studies of morphology and microstructure have shown nanocrystallinity of the materials. The Raman...
-
Aggregation properties of some zirconium phosphate loaded with dirhenium(III) complexes
PublikacjaOne of the important areas of modern science is the selection of the right forms of drug delivery. Layered inorganic nanoparticles, such as zirconium phosphate, have proven themselves well in this area. The study of the properties of these systems and methods of their preparation makes it possible to determine a rational technology of their manufacture, storage conditions as well as suggest a possible mechanism of therapeutic action....
-
On the influence of shell element properties on the response of car model in crash test
PublikacjaIt goes without saying that numerical simulations play important role in the modern engineering practice. Contemporary CAD environments combined with FEM solvers, along with computer power of modern processors, give the engineer fast and efficient tool. Ultimately, however it is the user alone who is responsible for the correctness of the results. As long as the FEM calculations remain in the sphere of academic exercise, the inevitable...
-
The effect of tyre rubber grinding method on the rubber-asphalt binder properties
PublikacjaRubber products, especially those used in the automotive industry, are responsible for a significant amount of waste, mainly in the form of worn tyres. One way to recycle tyres is to use them as an asphalt binder modifier. The properties of rubber-asphalt binders vary greatly depending on the morphology of the ground tyre rubber (GTR) grains and the type of tyre to be recycled (car/truck). The paper presents the results of research...
-
Case study of water vapour transmission properties of EPDM façade membranes
PublikacjaThis research aimed to investigate the water vapour transmission properties of chosen EPDM membranes applied in façade and window systems under laboratory tests. The applied procedure included in national and international standards utilized for the laboratory tests of water vapour transmission properties of EPDM membrane is described. Two main types (outside and inside types) of EPDM membranes are laboratory tested. The authors...
-
Preparation and Properties of Thermoplastic Polyurethane Composites Filled with Powdered Buckwheat Husks
PublikacjaBio-based fillers for the polymer composites are still interesting from the scientific and industrial point of view, due to their low cost and renewable nature. In this work partially green composites were obtained by the mixing of thermoplastic poly(ester-urethane) with the unmodified and modified (by acetylation) grinded buckwheat husks. Obtained biocomposites were characterized in the terms of their chemical structure (FTIR),...
-
Application of Artificial Neural Networks to Predict Insulation Properties of Lightweight Concrete
PublikacjaPredicting the properties of concrete before its design and application process allows for refining and optimizing its composition. However, the properties of lightweight concrete are much harder to predict than those of normal weight concrete, especially if the forecast concerns the insulating properties of concrete with artificial lightweight aggregate (LWA). It is possible to use porous aggregates and precisely modify the composition...
-
QRS Morphology-Based EDR Signal—Factors Determining its Properties
PublikacjaRespiration-induced signals contain a clinically significant information. It could be obtained utilizing both direct and indirect methods. ECG-Derived Respiration (EDR) method is the latter one. However, in this case, two approaches could be distinguished. First one is based on determining changes in the morphology of QRS complexes while the second one is based on the Respiratory Sinus Arrhythmia (RSA) mechanism. The former approach...
-
Praseodymium Orthoniobate and Praseodymium Substituted Lanthanum Orthoniobate: Electrical and Structural Properties
PublikacjaIn this paper, the structural properties and the electrical conductivity of La1−xPrxNbO4+δ (x = 0.00, 0.05, 0.1, 0.15, 0.2, 0.3) and PrNbO4+δ are presented and discussed. All synthesized samples crystallized in a monoclinic structure with similar thermal expansion coefficients. The phase transition temperature between the monoclinic and tetragonal structure increases with increasing praseodymium content from 500 ◦C for undoped...
-
Biomass-Derived Nitrogen Functionalized Carbon Nanodots and Their Anti-Biofouling Properties
PublikacjaThe prevalence of the antibiotic resistant bacteria remains a global issue. Cheap, sustainable and multifunctional antibacterial membranes are at the forefront of filtrating materials capable of treating multiple flow streams, such as water cleansing treatments. Carbon nanomaterials are particularly interesting objects shown to enhance antibacterial properties of composite materials. In this article, amino-functionalized, photoluminescent...
-
PROCESSING, MECHANICAL AND THERMAL PROPERTIES OF RECYCLED LOW-DENSITY POLYETHYLENE STREAMS
PublikacjaThe recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for the potential methods of their utilization. Nevertheless, for the efficient application of recycled materials it is crucial to analyze their performance. Therefore, in presented paper we investigated the processing (melt flow index),...
-
Gigantic electro-chemo-mechanical properties of nanostructured praseodymium doped ceria
PublikacjaSome oxygen defective fluorites are non-Newnham electrostrictors, i.e., the electromechanical response does not depend on their dielectric properties. Here, we show gigantic electrostriction in nanocrystalline 25 mol% praseodymium doped ceria (PCO) bulk ceramics. The material was fabricated with a fieldassisted spark plasma sintering (SPS) process from high-purity nanoscale PCO powders (<20 nm). The SPS process consolidates the...
-
Investigation of Acoustic Properties of Poroelastic Asphalt Mixtures in Laboratory and Field Conditions
PublikacjaMeasures for the improvement of acoustic conditions in the vicinity of roads include the construction of pavement structures with low-noise surfaces with optimal macrotexture and the highest possible sound absorption coefficient. Laboratory evaluation of acoustic properties of a designed asphalt mixture before its placement in the pavement is a good solution. Currently, the most popular method for the determination of the sound...
-
Magnetic properties of α-KCoPO4 compound with a chiral polar crystal structure
PublikacjaWe have obtained polycrystalline samples of a metastable α variant of KCoPO4 by low temperature (350–400 °C) solid state metathesis reaction of potassium oxalate and ammonium cobalt orthophosphate. The material crystallizes in a polar chiral structure (sg. P63, no. 173). Measurements of magnetic properties reveal antiferromagnetic interactions and no ordering observed down to T = 1.9 K, well below the Weiss temperature |Θcw| =...
-
Cold recycled mixtures for binder courses - laboratory evaluation of mechanical properties
PublikacjaCold recycled mixtures composed with cement and bituminous emulsion are nowadays commonly used material for base layer. Typical pavement with cold recycled mixtures usually consists of two asphalt courses (wearing and binding course) constructed over cold recycled base. Therefore the next step in cold recycling is possibility of design of binding courses with recycled materials, but with potential to obtain high quality mixtures...
-
Low-Molecular Pyrazine-Based DNA Binders: Physicochemical and Antimicrobial Properties
PublikacjaPyrazine and its derivatives are a large group of compounds that exhibit broad biological activity, the changes of which can be easily detected by a substituent effect or a change in the functional group. The present studies combined theoretical research with the density functional theory (DFT) approach (B3LYP/6-311+G**) and experimental (potentiometric and spectrophotometric) analysis for a thorough understanding of the structure...
-
Tribological Properties of Thermoplastic Materials Formed by 3D Printing by FDM Process
PublikacjaThe dataset entitled 3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_4 contains: the time base (expressed in seconds and minutes), the friction torque for sliding friction, rotational velocity of the counter – specimen (velocity of sliding), friction coefficient, load in the friction contact...