Filtry
wszystkich: 5382
-
Katalog
- Publikacje 3875 wyników po odfiltrowaniu
- Czasopisma 44 wyników po odfiltrowaniu
- Konferencje 7 wyników po odfiltrowaniu
- Osoby 58 wyników po odfiltrowaniu
- Wynalazki 1 wyników po odfiltrowaniu
- Projekty 4 wyników po odfiltrowaniu
- Zespoły Badawcze 1 wyników po odfiltrowaniu
- Kursy Online 26 wyników po odfiltrowaniu
- Dane Badawcze 1366 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: silos measurements
-
Induction Motor Multiscalar Model Based Sensorless Control Using Power Measurement
Publikacja -
Influence of the analyzing window on electrode impedance measurement by the continuous frequency scanning method
Publikacja -
Measurement invariance of the Belief in a Zero‐Sum Game scale across 36 countries
Publikacja -
<title>Modeling of noncontact temperature measurement system using multiwavelength pyrometry</title>
Publikacja -
Evaluation of a 10 nm Particle Number Portable Emissions Measurement System (PEMS)
Publikacja -
Fault loop impedance measurement in low voltage network with residual current devices
PublikacjaW sieciach i instalacjach niskiego napięcia z wyłącznikami różnicowoprądowymi pomiar impedancji pętli zwarciowej jest kłopotliwy. Prąd pomiarowy powoduje ich zbędne zadziałanie, co uniemożliwia prawidłowe wykonanie pomiaru. W artykule omówiono przyczyny zbędnego zadziałania wyłączników różnicowoprądowych podczas pomiaru impedancji pętli zwarciowej oraz warunki, w jakich ten pomiar można wykonać poprawnie.
-
Miniaturized Passive Emission Chambers for In Situ Measurement of Emissions of Volatile Organic Compounds
PublikacjaThe results of many different studies have demonstrated unequivocally that the quality of indoor air is often much worse than that of atmospheric air. The presence of dangerous chemical compounds in indoor air can have an adverse impact on human health and cause numerous diseases of the respiratory and circulatory systems. Such harmful chemicals get into indoor air as a result of their emission from building and indoor materials....
-
Measurement of magnetic signals of vehicles with denoising by matched filtering with FPGA FFT processor
PublikacjaW artykule przedstawiono realizację systemu do analizy i identyfikacji pojazdów oparty na pomiarze indukcji magnetycznej. Proponowany system może być zastosowany do wykrywania i identyfikacji pojadów zawierających elementy ferromagnetyczne, które zaburzają pole magnetyczne ziemi. Zaburzenie to można zmierzyć przy zastosowaniu trójosiowych magnetometrów transduktorowych, pracującyh w układzie różnicowycm. Zastosowano w systemie...
-
Determination of magnetisation conditions in a Double-Core Barkhausen Noise measurement set-up
PublikacjaThe magnetic Barkhausen effect is useful forassessing 1D and 2D stress states of ferromagnetic steelobjects. However, its extension to technically importantmaterials, such as duplex anisotropic steels, remains challenging. The determination of magnetisation inside the studied object and the electromagnet for various geometries, materials and magnetisation angles is a key issue.Three-dimensional, dynamic finite element analysis...
-
Low Frequency Noise Measurement of Reverse Polarized Silicon Carbide Schottky Diodes
PublikacjaW artykule przedstawiono wyniki pomiaró szumów cz. wstecznie spolaryzowanych diod Schottky'ego.
-
Measurement of the earth fault loop impedance in a low voltage network with operating loads
PublikacjaW artykule przedstawiono problematykę dokładności pomiaru impedancji pętli zwarciowej w sieciach z obciążeniami roboczymi. Klasyczne metody pomiarowe i mierniki mogą powodować błędy pomiaru przekraczające dopuszczalną wartość. Z tego powodu może wystąpić ryzyko porażenia prądem elektrycznym, ponieważ przy doziemieniu nie będzie spełniony warunek samoczynnego wyłączenia zasilania. Błędy pomiaru w sieci z obciążeniami roboczymi można...
-
Application of Maximum-Length Sequences to impulse response measurement of hydroacoustic communications systems
PublikacjaThere is a growing interest in digital transmission of telemetry data on ultrasonic waves. The dependence of signal attenuation on squared frequency, specific to the hy-droacoustic systems, induces problems that do not exist in monochromatic, narrowband radio communications systems. For adapting the transmission parameters to current propagation conditions, a precise knowledge of instantaneous changes of channel performances is...
-
Challenges in oscillometric blood pressure measurement in atrial fibrillation: looking for practical solutions
Publikacja -
Measurement of ethylene production as a method for determining the optimum harvest date of ‘Jonagored’ apples
Publikacja -
Measurement of sub-nanometer molecular layers with ISFET without a reference electrode dependency
PublikacjaA new method of detection and measurement with sub-nanometer resolution of layers adsorbed or bonded to the ISFET's gate dielectric was presented. The sensitivity of this method is high enough to detect even partial mono-layer covering. The transconductance measurement of the ISFET provides independence of the output signal from pH changes and the driving electrode electrochemical potential instabilities. The stable reference electrode...
-
Miniaturized passive emission test chamber for in-situ measurement of emissions of organic compounds
PublikacjaThe results of many different studies have demonstrated unequivocally that the quality of indoor air is often much worse than that of atmospheric air (outdoor). One of the main groups of chemical compounds present in indoor air, with proven harmfulness to health,are volatile organic compounds (VOCs). VOCs present indoor comprise a wide variety of hydrocarbons and hydrocarbons derivatives including aliphatic, aromatics, alkylbenzens,...
-
Methods of measurement signal acquisition from the rotational flow meter for frequency analysis
PublikacjaOne of the simplest and commonly used instruments for measuring the flow of homogeneous substances is the rotational flow meter. The main part of such a device is a rotor (vane or screw) rotating at a speed which is the function of the fluid or gas flow rate. A pulse signal with a frequency proportional to the speed of the rotor is obtained at the sensor output. For measurements in dynamic conditions, a variable interval between...
-
Application of polarisation-maintaining side-hole fibres do direct force measurement
PublikacjaW pracy przedstawiono zastosowanie utrzymujących polaryzację światłowodów typu Side Hole do bezpośredniego pomiaru siły. Dla wybranych struktur tych światłowodów wyznaczono, przy pomocy Metody Elementów Skończonych i metody modów sprzężonych, czułość na siłę działającą prostopadle do osi symetrii światłowodu. Określono zależność tej czułości od poszczególnych wymiarów struktur tych światłowodów. Następnie, biorąc pod...
-
The measurement and calculation of gas temperature inside a switchgear during fault arc period.
PublikacjaW artykule przedstawiono metodę obliczania temperatury gazu wewnątrz rozdzielnicy szczelnej z izolacją powietrzną podczas zwarć łukowych w oparciu o równanie przewodnictwa cieplnego. Przedstawiono wyniki badań eksperymentalnych temperatury gazów podczas zwarć z łukiem wędrującym. Opisano model do badań, układ probierczy i warunki badań. Wyniki obliczeń porównano z wynikami badań eksperymentalnych.
-
Time domain diagnosis of anticorrosion coatings via shape designed measurement signals.
PublikacjaW pracy przedstawiono operującą w dziedzinie czasu metodę diagnostyki pokryć przeciwkorozyjnych, na poziomie identyfikacji parametrów obwodu zastępczego. Metoda jest oparta na pobudzeniu obiektu sygnałem niekonwencjonalnym o projektowanym kształcie i pomiarze odpowiedzi obiektu (tzw. obserwabla) po upływie zadanego czasu T. Parametry obwodu zastępczego są obliczane bezpośrednio z obserwabli na podstawie równań wynikających z topologii...
-
Accelerated impedance spectrum measurement via multisine perturbationand digital filter banks
PublikacjaPrzedstawiono przyspieszoną metodę pomiaru widma impedancyjnego, zorientowaną na pomiary jakości powłok przeciwkorozyjnych, modelowanych liniowymi obwodami zastępczymi. Metoda polega na pobudzeniu układu wielosinusoidalnym sygnałem popudzającym oraz analizie pobudzenia i odpowiedzi obiektu przez bank filtrów cyfrowych. Przedstawiono podstawy teoretyczne metody oraz propozycję metodologii pomiaru. Przeanalizowano wyniki symulacji...
-
Example of practical use of vibration measurement results - study of settlement of the Wisłoujście Tower
PublikacjaW pracy przedstawiono wyniki identyfikacji parametrów posadowienia wieży Twierdzy Wisłoujście. Badanie oparto na zidentyfikowanych w pomiarach częstotliwościach drgań swobodnych wieży. Przyjęto prosty model dynamiczny obiektu, dobrze opisujący jego zachowanie.
-
Influence of the analyzing window on electrode impedance measurement by thecontinuous freqency scanning method
PublikacjaPrzeprowadzono pomiary impedancyjne modelowego układu elektrycznego RC techniką ciągłego skanowania częstotliwościowego. Wyznaczono impedancję modelowego układu dla różnych okien analizujących oraz ich różnych wielkości. Wyznaczone dla różnych okien analizujących wartości R i C porównywano z wartościami rzeczywistymi. Stwierdzono wpływ rodzaju okna analizującego oraz jego długość na dokładność otrzymywanych wyników.
-
Conditions for measurement, analog-to-digital conversion and frequency analysis of irregularities of profile surface
PublikacjaPrzedstawiono uwarunkowania pomiaru, przetwarzania analogowo-cyfrowego i analizy częstotliwościowej nierówności powierzchni toczonych dla celów rozpoznawania ich głównych składowych. Przedstawiono ograniczenia w pomiarze igłą, która odwzorowuje nierówności poprzeczne. Podano zależności parametrów pomiaru cyfrowego nierówności warunkujące zakresy ich rozpatrywania. Dla wartości przedziału próbkowania, dla którego nie jest spełnione...
-
Fault Loop Impedance Measurement in Circuits Fed by UPS and Principle of Safety Protection
PublikacjaThis paper indicates a significant problem of uncertainty of fault loop impedance (FLI) measurement in circuits powered from uninterruptible power supply (UPS) (double-conversion AC-DC-AC). The correctly determined value of this impedance, related to the short-circuit current disconnection time and to the reference value, is one of the most important elements that determines the approval of an electrical installation and its receivers...
-
Determination of the tram track axis using a multi receiver GNSS measurement system
PublikacjaThis article refers to research, that has been conducted by an interdisciplinary research team from the Gdańsk University of Technology and the Maritime University in Gdynia since 2009. These investigation concerns the determination of a railway track axis using the mobile satellite measurement technique. Following the dynamic development of GNSS techniques, that could be seen in the last decade, the team carried out further experiments...
-
A method of earth fault loop impedance measurement without unwanted tripping of RCDs
PublikacjaIn low-voltage networks, earth fault loop impedance (EFLI) measurement is the basis for assessing the effectiveness of automatic disconnection of supply. Such a measurement is performed during initial and periodical verification, especially in a TN low-voltage network. Nowadays, due to widespread application of residual current devices (RCDs), such test is difficult in many circuits because RCDs operate during the test. In this...
-
A High-Efficient Measurement System With Optimization Feature for Prototype CMOS Image Sensors
PublikacjaIn this paper, a gray-scale CMOS image sensor (CIS) characterization system with an optimization feature has been proposed. By using a very fast and precise control of light intensity, based on the pulsewidth-modulation method, it is avoided to measure the illuminance every time. These features accelerate the multicriteria CIS optimization requiring many thousands of measurements. The system throughput is 2.5 Gb/s, which allows...
-
Suppression of distortions in signals received from Doppler sensor for vehicle speed measurement
PublikacjaDoppler sensors are commonly used for movement detection and speed measurement. However, electromagnetic interference and imperfections in sensor construction result in degradation of the signal to noise ratio. As a result, detection of signals reflected from moving objects becomes problematic. The paper proposes an algorithm for reduction of distortions and noise in the signal received from a simple, dual-channel type of a Doppler...
-
MEASUREMENT AND ANALYSIS OF A FLOOD WAVE PROPAGATION ON THE KACZA RIVER IN GDYNIA IN NORTHERN POLAND
PublikacjaKacza river is located in northern Poland in the neighborhood of the Gulf of Gdansk and the Baltic Sea. A Kacza having length of 15 km and catchment area of 53 km2 collects the water into the Gulf mostly from inhabited and forested areas within the administrative boundaries of the city of Gdynia. On the 14th and 15th of July 2016 in northern Poland on the large area of Tri-City agglomeration (Gdynia, Gdansk and Sopot) total daily...
-
Analysis of distance measurement errors in CW FM sonar with MLS code modulation
PublikacjaAlthough used in the classic silent sonar, the CW FM sounding signal has a major flaw which is its inaccuracy in determining the distance to a target. The authors of the article have developed a concept of silent sonar using frequency modulation signals switched by pseudorandom codes, already discussed in their previous work. This article presents a detailed analysis of errors in CW FM sonar with pseudo-random sequence code modulation...
-
Modelling and Measurement of Folk Guitar: Truss Rod and Strings in Numerical Analysis of Tone
PublikacjaThe study makes an attempt to model a complete vibrating guitar including its non-linear features, specifically the tension-compression of truss rod and tension of strings. The purpose of such a model is to examine the influence of design parameters on tone. Most experimental studies are flawed by uncertainties introduced by materials and assembly of an instrument. Since numerical modelling of instruments allows for deterministic...
-
INFLUENCE OF WRONGLY ASSUMED PROBABILITY DISTRIBUTION ON THE UNCERTAINTY OF RESISTANCE MEASUREMENT BY TECHNICAL METHOD
PublikacjaThe paper presents studies on the influence of probability distributions on the expanded uncertainty of the resistance measurement. Choosing the correct probability distribution is very important to estimate of measurement uncertainty. The most commonly used distribution is the rectangular distribution. The paper presents the results of analysis of the resistance measurement uncertainty using the technical method of two resistances:...
-
Investigation of Weigh-in-Motion Measurement Accuracy on the Basis of Steering Axle Load Spectra
PublikacjaWeigh-in-motion systems are installed in pavements or on bridges to identify and reduce the number of overloaded vehicles and minimise their adverse eect on road infrastructure. Moreover, the collected trac data are used to obtain axle load characteristics, which are very useful in road infrastructure design. Practical application of data from weigh-in-motion has become more common recently, which calls for adequate attention to...
-
FIBRE-OPTIC SENSOR FOR SIMULTANEOUS MEASUREMENT OF THICKNESSAND REFRACTIVE INDEX OF LIQUID LAYERS
PublikacjaIn this paper, we present a fibre-optic sensor for simultaneous measurement of refractive index and thickness of liquid layers. We designed an experimental low-coherence setup with two broadband light sources and an extrinsic fibre-optic Fabry–Pérot interferometer acting as the sensing head. We examined how the refractive index of a liquid film and its thickness affect spectrum at the output of a fibre-optic interferometer. We...
-
Comparison of Different Measurement Techniques as Methodology for Surveying and Monitoring Stainless Steel Chimneys
PublikacjaThe measurement of a chimney axis is an engineering geodesy task. These measurements allow to assess the technical condition of chimneys and are usually carried out for reinforced concrete chimneys. When measuring high chimneys, the main problem may be the need to go a long distance to take a measurement. The surface of the chimney can also be problematic because it can absorb so much light from the range finder that total station...
-
Measurement Campaign and Mathematical Model Construction for the Ship Zodiak Magnetic Signature Reproduction
PublikacjaThe paper presents the partial work done within the framework of the EDA Siramis II project focused on magnetic signature reproduction of ships. Reproduction is understood here as the ability to determine the magnetic anomaly of the local Earth magnetic field in any direction and at any measurement depth due to the presence of the analysed object. The B-91 type hydrographic ship Zodiak was selected as the real case study. The work...
-
Measurement of expenditure efficiency of Polish cities with county rights in the context of quality of life
PublikacjaThe article is devoted to the measurement of efficiency of overall expenditures. The purpose of the study is to evaluate the efficiency of use of budget resources by local government units in the context of fostering quality of life. The subject of the study is 65 Polish cities with county rights (county status). Calculations were carried out using Data Envelopment Analysis (DEA). The results of analysis confirm the two research...
-
Measurement of distance, velocity and angle of arrival using FMCW-CW combined waveform
PublikacjaA procedure of tacking small flying object based on a general principle of FMCW and Doppler radar is presented. In order to increase measurement range, this technique uses active signal source on the moving object. For simultaneous measurements of distance, radial velocity and direction (AoA) as well as simplified synchronization a combined FMCW-CW waveform is proposed. The presented measurement system was realized and verified...
-
Energy Recovery Analysis in A-Type Pressure Regulation and Measurement Stations in Istanbul, Esenyurt
Publikacja -
Application of Particle Image Velocimetry method for monitoring the volume changes during silo flow on the basis of X-radiographs
PublikacjaW artykule przedstawiono wyniki badań nad zastosowaniem techniki pomiarowej PIV (Particle Image Velocimetry) do analizy zmian objętościowych zachodzących w materiale sypkim w czasie opróżniania silosu prostokątnego. Jako mateirły do analizy wykorzystano cyfrowe radiografy uzyskane z kontynualnej rejestracji z użyciem systemu tomografii promieni X. Szcególny nacisk położono na analizę zmian objętościowych zachodzącyh w kanale przepływu.
-
Combining X-ray tomogrpahy imaging and DEM simulations to investigate granular material flow during silo discharging
PublikacjaEven after few decades of research, the study of particle motion taking place during silo discharging hasn’t been fully addressed, both experimentally and numerically, because of nontrivial behaviors that occur during associated flow patterns. For instance, discrete element method (DEM) has shown good qualitative prediction potential of velocity profile, but, on the other hand, frequently failed to match quantitatively experimental...
-
Design, Realization and Measurements of Enhanced Performance 2.4 GHz ESPAR Antenna for Localization in Wireless Sensor Networks
PublikacjaThis paper presents the design, realization and measurements of an Electronically Steerable Parasitic Array Radiator (ESPAR) antenna with enhanced performance of estimating the incoming signal direction. Designed antenna is dedicated for 2.4 GHz ISM applications with emphasis on Wireless Sensor Networks (WSN). Proposed antenna provides different radiation patterns by proper configuration of the parasitic elements. Thus, several...
-
Measurements of Spectral Spatial Distribution of Scattering Materials for Rear Projection Screens used in Virtual Reality Systems
PublikacjaRapid development of computing and visualisation systems has resulted in an unprecedented capability to display, in real time, realistic computer-generated worlds. Advanced techniques, including three-dimensional (3D) projection, supplemented by multi-channel surround sound, create immersive environments whose applications range from entertainment to military to scientific. One of the most advanced virtual reality systems are CAVE-type...
-
The fixed state in impedance measurements of a two-step electrode reaction proceeding with accompanying adsorption of an intermediate product
Publikacja -
Solubility of sulfanilamide in binary solvents containing water: Measurements and prediction using Buchowski-Ksiazczak solubility model
Publikacja -
Measurements of OF QoS/QoE parameters for media streaming in a PMIPv6 TESTBED WITH 802.11 b/g/n WLANs
PublikacjaA growing number of mobile devices and the increasing popularity of multimedia services result in a new challenge of providing mobility in access networks. The paper describes experimental research on media (audio and video) streaming in a mobile IEEE 802.11 b/g/n environment realizing network-based mobility. It is an approach to mobility that requires little or no modification of the mobile terminal. Assessment of relevant parameters...
-
Measurements and Visualization of Sound Intensity Around the Human Head in Free Field Using Acoustic Vector Sensor
PublikacjaThis paper presents measurements and visualization of sound intensity around the human head simulator in a free field. A Cartesian robot, applied for precise positioning of the acoustic vector sensor, was used to measure sound intensity. Measurements were performed in a free field using a head and torso simulator and the setup consisting of four different loudspeaker configurations. The acoustic vector sensor was positioned around...
-
Folding kinetics of WW domains with the united residue force field for bridging microscopic motions and experimental measurements
Publikacja -
INTERLABORATORY COMPARISON OF THE ELECTROMAGNETIC EMISSION MEASUREMENTS USING FAR AND GTEM TEST SITES UP TO 1 GHz
PublikacjaElectromagnetic emission limiting is one of the basic requirements in the European Directive 2014/30/EU (EMC Directive). Manufacturers often use alternative methods of measurements to make preliminary verification of emission. This paper presents and analyzes problem with comparison between measurements in different test sites: FAR (Fully Anechoic Room) and GTEM (Gigahertz Transverse Electromagnetic cell). FAR is assumed as the...