Filters
total: 646
filtered: 554
Search results for: PROPULSION SHAFT FATIGUE
-
INVESTIGATIONS OF THE LABORATORY FARYMANN DIESEL ENGINE D10 TYPE BY MEANS OF A LANGMUIR PROBE
PublicationA precise determination of the crankshaft angular position, at which fuel ignition occurs in the SI engine, enables credible diagnosis of the technical state of its working space as well as of the fuel feed system. An observation of the Langmuir probe signal provides entirely new possibilities for engine diagnostics. The probe is introduced into the working space of a cylinder through its indicator valve. This paper presents the...
-
Estimation of Screw Displacement Pile-Bearing Capacity Based on Drilling Resistances
PublicationThis article presents an engineering, empiricalmethod of estimating the bearing capacity and settlementcharacteristics Q-s of screw displacement piles andcolumns, based on soil resistance encountered during thedrilling to form piles/columns in the ground. The methodwas developed on the basis of correlation analyses of thetest results of 24 piles made during the “DPDT-Auger”research project (Krasiński et al., 2022a). In the proposedmethod,...
-
Axial-Flux Permanent-Magnet Dual-Rotor Generator for a Counter-Rotating Wind Turbine
PublicationCoaxial counter-rotating propellers have been widely applied in ships and helicopters for improving the propulsion efficiency and offsetting system reactive torques. Lately, the counter-rotating concept has been introduced into the wind turbine design. Distributed wind power generation systems often require a novel approach in generator design. In this paper, prototype development of axial-flux generator with a counter-rotating...
-
Negative impact of constant RPM control strategy on ship NOx emission in waves
PublicationIn severe wave conditions, the ship propulsion system is loaded with high fluctuations due to external disturbances. The highly fluctuating loads enforce radical changes in the main engine torque, which in turn demands variation of the fuel rate injected into the cylinders if a constant rotational speed strategy is applied. Therefore, the temperature of gases varies to a large extent during the combustion process in the cylinders....
-
Lessons learned during SRAD hybrid motor development
PublicationStudent Researched and Developed (SRAD) hybrid rocket motor H-15 with total impulse of 15 $kNs$ was built. First version of the engine has average thrust of 3 $kN$, the second, improved one is prepared with an aim to have average thrust of 5 $kN$. Engine development was started from scratch and went through phases of: definition of design assumptions and constraints, numerical modelling to predict engine performance, CAD and CAM...
-
Modern GFRP Composite Footbridges
PublicationApplication of GFRP composites in civil engineering is still not large but already noticeable. Advantages of this material, such as: low volume weight, relatively high stiffness and strength, well fatigue resistance, easiness in shaping, high material damping and high environmental resistance, make it attractive for bridge and in particular foot-bridge designers. It is estimated that nowadays in the world there are realized hundreds...
-
Modelling of the Baumann turbine stage operation Part II. Free and kinetic vibrations
PublicationIn this paper has been presented a methodology of validation a novel mathematical model dedicated to evaluation and prediction of material degradation and demage of steam turbine elements such as blades, valves and pipes due to three mechanisms: stress-corosion, high-temperature creep and low-cyclic fatigue. The validation concept is based on an experimental setup manufactured in the Laboratory of Faculty of Mechanical and Power...
-
Kompensacja skoków ciśnienia w pompie tłoczkowej o zmiennej wydajności z rozrządem krzywkowym
PublicationPrzedmiotem rozprawy doktorskiej jest opis matematyczny, badania i symulacja mechanizmu kompensacji skoków ciśnienia w pompie tłoczkowej z rozrządem krzywkowym typu PWK. W rozprawie przedstawiono istniejące rozwiązania konstrukcyjne pomp tłokowych, kładąc szczególny nacisk na przedstawienie stosowanych w nich mechanizmów rozrządu i kompensacji skoków ciśnienia. Ponadto szczegółowo opisano budowę i zasadę działania pompy PWK będącej...
-
Real-time hybrid model of a wind turbine with doubly fed induction generator
PublicationIn recent years renewable sources have been dominating power system. The share of wind power in energy production increases year by year, which meets the need to protect the environment. Possibility of conducting, not only computer simulation, but also laboratory studies of wind turbine operation and impact on the power system and other power devices in laboratory conditions would be very useful. This article presents a method...
-
INFLUENCE OF TIME ON THE BEARING CAPACITY OF PRECAST PILES
PublicationOne of the most popular types of foundations in layered subsoil with very differentiated soil shear strengths are precast piles. One of the reasons is a fact that we can well control the driving process during the installation of these piles. The principles of the assessment of bearing capacity and settlements of the piles given by Eurocode 7, concentrate on two main methods, i.e. Static Pile Load Tests (SPLT) and Dynamic Driving...
-
Geometric working volume of a satellite positive displacement machine
PublicationThis article describes a method for determining the geometric working volume of satellite positive displacement machines (pump and motor). The working mechanism of these machines is satellite mechanism consisting of two non-circular gears (rotor and curvature) and circular gears (satellites). Two variants of the satellite mechanism are presented. In the first mechanism, the rolling line of the rotor is a sinusoid "wrapped" around...
-
The experience of movement in orbital space architecture: A narrative of weightlessness
PublicationBased upon a combination of architectural theories, the knowledge of space environment, and psychology of isolated and confined environments, this qualitative research aims to study orbital space settlement in a way to get the built space congenial to the human experience of movement. In this sense, sensors, self-propulsion or mechanical actuators, the inhabitant’s mental and visual capacity for movement, as well as the represented...
-
DETERMINATION OF SEAKEEPING PERFORMANCE FOR A CASE STUDY VESSEL BY THE STRIP THEORY METHOD
PublicationThe increase of seakeeping performance is of particular importance for car and passenger ferries, service ships in the gas and oil extraction industry and offshore wind power farm industry, as well as for special purpose ships (including military applications). In the water areas of the Baltic Sea, North Sea, and Mediterranean Sea, which are characterised by a short and steep wave, the hull shape has a substantial impact on the...
-
Application of unmanned USV surface and AUV underwater maritime platforms for the monitoring of offshore structures at sea
PublicationThe operation of offshore structures at sea requires the implementation of advanced systems for their permanent monitoring. There is a set of novel technologies that could be implemented to deliver a higher level of effective and safe operation of these systems. A possible novel solution may be the application of a new maritime unmanned (USV) surface and underwater vehicles/platforms (AUV). Application of such vehicles/platforms...
-
The experience of movement in orbital space architecture: A narrative of weightlessness
PublicationBased upon a combination of architectural theories, the knowledge of space environment, and psychology of isolated and confined environments, this qualitative research aims to study orbital space settlement in a way to get the built space congenial to the human experience of movement. In this sense, sensors, self-propulsion or mechanical actuators, the inhabitant’s mental and visual capacity for movement, as well as the represented...
-
Structural Health Monitoring of Overhead Power Transmission Lines
PublicationStructural Health Monitoring (SHM) is a novel and continuously developing branch of science and technology that draws attention of scientists all over the world. It creates opportunities to detect, localize and identify structural damage of various types such as: line breakage, permissible sag, bolt loosening, fatigue cracking or insulator contamination. On the other hand the methods used to estimate the remaining operational...
-
ADAPTATION OF ENGINEERING FEA-BASED ALGORITHMS TO LCF FAILURE AND MATERIAL DATA PREDICTION IN OFFSHORE DESIGN
PublicationThere is an ever growing industrial demand for quantitative assessment of fatigue endurance of critical structural details. Although FEA-based calculations have become a standard in engineering design, problems involving the Low-To-Medium cycle range (101-104) remain challenging. This paper presents an attempt to optimally choose material data, meshing density and other algorithm settings in the context of recent design of the...
-
Experimental comparison of hydrodynamic thrust bearings with different pad surface materials
PublicationBabbitt is the material most frequently used as the pad surface material for hydrodynamic bearings operating at usual operating conditions. It shows many advantages important for safe bearing operation, as for example: low friction coefficient, corrosion resistance, fair mechanical properties and outstanding conformability. On the other hand, it is not free from disadvantages, such as limited fatigue strength or limited resistance...
-
The Use of Direct Shear Test for Optimization of Interlayer Bonding Under a Poroelastic Layer
PublicationPoroelastic Road Surfaces (PERS) are characterised by porous structure with air void content of 20% or higher and stiffness almost 10 times lower than that of a standard asphalt course. Such properties enable noise reduction by up to 12 dB in comparison to SMA 11 mixture. However, the disadvantage of a poroelastic pavement is its low durability, which partially results from delamination from the lower layer. The paper aims to investigate...
-
Chemical Theory of Machines, basic principles of strength with examples of calculations
PublicationThis book encompasses the essential range of information on technical aspects of mechanical design. It was written primarily for the students and staff of chemistry faculties of technical universities, yet it may also be utilized by everyone, who ether would like to try or already enjoys designing, but cannot take advantage of typical stress & machine construction handbooks. These handbooks often require familiarity with the concepts...
-
Water-Lubricated Sintered Bronze Journal Bearings—Theoretical and Experimental Research
PublicationWater lubricated bearings are used from many years in shipbuilding, hydro power and other industries because of their advantages such as: extensive serviceable life, low coefficient of friction, longevity of shaft sleeve, good abrasion resistance, low maintenance required, unit simplicity, no danger of pollution and low price. Various types of water lubricated sliding bearings have been tested at the Technical University of Gdansk...
-
Effect of presence of lifting pocket on the THD performance of a large tilting-pad thrust bearing
PublicationHydrostatic assistance is a commonly used method to improve limited load carrying ability of tiltingpad thrust bearings during transient states of operation of vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves, etc.), it also requires manufacturing of special recesses/pockets at pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up...
-
FEM modelling of screw displacement pile interaction with subsoil
PublicationPredicting the-settlement characteristics of piles is an important element in the designing of pile foundations. The most reliable method in evaluating pile-soil interaction is the static load test, preferably performed with instrumentation for measuring shaft and pile base resistances. This, however, is a mostly post-implementation test. In the design phase, prediction methods are needed, in which numerical simulations play an...
-
EMISJA AKUSTYCZNA JAKO SYGNAŁ DIAGNOSTYCZNY ODWZOROWUJĄCY ZMĘCZENIOWE ZUŻYCIE WARSTW ŚLIZGOWYCH PANWI ŁOŻYSK GŁÓWNYCH I KORBOWYCH SILNIKÓW O ZAPŁONIE SAMOCZYNNYM
PublicationW artykule przedstawiono wyniki badań laboratoryjnych, z których wynika, że emisja akustyczna (EA) może być uznana za sygnał diagnostyczny, przydatny do identyfikacji stanu technicznego łożysk głównych i korbowych okrętowych silników o zapłonie samoczynnym. Wykazano w nim bowiem, że parametry emisji akustycznej takie jak: czas rejestracji, energia sygnału, amplituda sygnału, ilość przekroczeń poziomu dyskryminacji, czas narastania,...
-
Caring for Children with Dravet Syndrome: Exploring the Daily Challenges of Family Caregivers
PublicationWhile Polish studies focus on the symptoms, causes and treatment of people suffering from Dravet syndrome (DS), much less is known about the situation of the family caregivers of DS children. This study was designed to explore the experiences, daily challenges and needs related to caring for DS children. An anonymous self-administered online questionnaire was developed. Thesurvey was completed by 75 family caregivers affiliated...
-
Influence of the notch rounding radius on estimating the elastic notch stress concentration factor in a laser welded tee joint
PublicationIn recent years an increased interest of industry in sandwich-type metal structures can be observed. These structures consist of thin plates of 2.5 mm in thickness separated by stiffeners of different shapes and forms. Welds joining the plates and stiffeners are made on the outer side of the plates using laser welding technique. A locally focused source of heat causes the plate to melt creating a very narrow and elongated joint....
-
Impact of overloaded vehicles on load equivalency factors and service period of flexible pavements
PublicationOverloaded vehicles occur less frequently in comparison to properly loaded vehicles but due to their greater potential to cause damage they significantly contribute to the distress of pavement structure. As the studies show, the phenomena of vehicles overloading intensifies when the control of traffic is poor and the average percentage of overloaded vehicles on analyzed roads varies from 6% to 23%. The main goal of the ar-ticle...
-
MINERAL CONTENT OF TREE SAP FROM THE SUBCARPATHIAN REGION
Publicationbut also as medicinal substance in folk medicine. Traditionally, it was used to treat various conditions, mostly anaemia and chronic fatigue. This study has been designed to establish the content of metallic elements (sodium, potassium, calcium, magnesium, zinc and copper) in sap collected from eight different species (silver birch, downy birch, hornbeam, Norway maple, boxelder maple, black walnut, black alder and white willow)...
-
Exploring the trends in flux-cored arc welding: scientometric analysis approach
PublicationFlux-cored arc welding (FCAW) is a universal group of welding methods in terms of the scope of application and automation possibilities, the share of which in various industries in many countries is still increasing. The paper presents the results of bibliographic analyses (scientometric analysis with the use of VOSviewer, Bibliometrix and CitNetExplorer tools) of a data set of 993 publications indexed in the Web of Science database...
-
Effect of aeration of antibiotic-loaded bone cement on its properties and bactericidal effectiveness
PublicationBACKGROUND: Antibiotic-loaded bone cements are now widely used in medicine. They are able to locally deliver antibiotic particles and they allow treat or protect against infection. It is assumed that the bactericidal effectiveness of bioactive bone cements depend on the parameters of its production. Hence, the aim of this study was to check the effect of aeration of bone cement before mixing the components on its properties as...
-
Effect of processing parameters on the cyclic behaviour of aluminium friction stir welded to spark plasma sintered aluminium matrix composites with bimodal micro-and nano-sized reinforcing alumina particles
PublicationUnderstanding the cyclic behaviour of Alumina reinforced Aluminium composites (Al-A2O3) was of critical importance, for their further application in the different industrial sectors. The present study is focussing on the cyclic behaviour of the Al-Alumina nanocomposite produced through the combination of spark plasma sintering (SPS) method and friction stir welding (FSW). The added Alumina with total content of 10% is the combination...
-
Bitumen Aging—Laboratory Simulation Methods Used in Practice and Selected Directions of Research on New Methods
PublicationChanges in the properties of bitumen binders that occur as a result of aging have a huge impact on the durability of products produced from them. In particular, asphalt pavements, which constitute the most common use of petroleum bitumen, are susceptible to damage resulting from the increasing stiffness of the bitumen during its life cycle. Increased stiffness of asphalt pavements reduces the pavement resistance to low-temperature...
-
Nonlinear Control of a Doubly Fed Generator Supplied by a Current Source Inverter
PublicationNowadays, wind turbines based on a doubly fed induction generator (DFIG) are a commonly used solution in the wind industry. The standard converter topology used in these systems is the voltage source inverter (VSI). The use of reverse-blocking insulated gate bipolar transistor (RB-IGBT) in the current source inverter topology (CSI), which is an alternative topology, opens new possibilities of control methods. This paper presents...
-
A Comparative Study of Fuzzy SMC with Adaptive Fuzzy PID for Sensorless Speed Control of Six-Phase Induction Motor
PublicationMulti-phase motors have recently replaced three-phase induction motors in a variety of applications due to the numerous benefits they provide, and the absence of speed sensors promotes induction motors with variable speed drives. Sensorless speed control minimizes unnecessary speed encoder cost, reduces maintenance, and improves the motor drive’s reliability. The performance comparison of the fuzzy sliding mode controller (FSMC)...
-
Longitudinal Motion Due to Action of Tunnel Thrusters
PublicationTunnel thrusters are propulsion and active control devises that provide a side force, or transverse thrust, to support mooring operations or position keeping. They shorten the time of manoeuvring, reduce the cost of towage and since inception, manoeuvrability specifically in ports has become a lot easier. Tunnel thrusters can either be operated manually or with the help of Dynamic Positioning systems which makes it even more efficient. Theoretically,...
-
Using differential pressure sensor to measure nitrous oxide level in a tank
PublicationA method for measuring the level of liquid nitrous oxide oxidizer in a hybrid rocket motor oxidizer tank is proposed. Presented approach is more accurate than the most commonly used method of this measurement, which employs weighting of the whole sounding rocket or an oxidizer tank. In our solution we use a differential pressure sensor to measure the change of pressure at the bottom of an oxidizer tank in comparison to the pressure...
-
A Comparative Study of Fuzzy SMC with Adaptive Fuzzy PID for Sensorless Speed Control of Six-Phase Induction Motor
PublicationMulti-phase motors have recently replaced three-phase induction motors in a variety of applications due to the numerous benefits they provide, and the absence of speed sensors promotes induction motors with variable speed drives. Sensorless speed control minimizes unnecessary speed encoder cost, reduces maintenance, and improves the motor drive’s reliability. The performance comparison of the fuzzy sliding mode controller (FSMC)...
-
Field Evaluation of High Modulus Asphalt Concrete Resistance to Low-Temperature Cracking
PublicationHigh-modulus asphalt concrete has numerous advantages in comparison to conventional asphalt concrete, including increased resistance to permanent deformations and increased pavement fatigue life. However, previous studies have shown that the construction of road pavements with High Modulus Asphalt Concrete (HMAC) may significantly increase the risk of low-temperature cracking. Those observations were the motivation for the research...
-
Analysis of diagnostic informativeness of the exhaust temperature of a naval gas turbine
PublicationThe conducted investigations aimed to carry out an analysis of the possibility that the failures identification in the automatic control system of a gas turbine engine could be worked out on the basis of measurements of the exhaust stream temperature behind the gas generator. The exhaust temperature represents a basic control parameter, enabling technical state evaluation of the engine within the operation process, which is observed...
-
Pile Model Tests Using Strain Gauge Technology
PublicationOrdinary pile bearing capacity tests are usually carried out to determine the relationship between load and displacement of pile head. The measurement system required in such tests consists of force transducer and three or four displacement gauges. The whole system is installed at the pile head above the ground level. This approach, however, does not give us complete information about the pile-soil interaction. We can only determine...
-
Decreasing CO2 Emissions By Reducing Tire Rolling Resistance
PublicationThe first motor vehicle was built by Nicolas Cugnot almost 250 years ago and since then there has been a continuous process of motor vehicles’ improvements, as well as development of new road pavements. The fuel crisis of the 70s of the 20th century made it clear to vehicle builders that measures should be taken to reduce vehicle fuel consumption and it contributed to an increased interest in electric vehicles. Although significant...
-
Effect of Overloaded Vehicles on Whole Life Cycle Cost of Flexible Pavements
PublicationThe phenomenon of vehicle overloading—illegal exceeding of maximum legal weight of vehicles, is a serious problem both in developing and developed countries around the world. Overloaded vehicles occur less frequently in comparison to properly loaded vehicles but due to their greater potential to cause damage they significantly contribute to distress of pavement structure. As studies show, the number of overloaded vehicles increases...
-
Effect of Coating Material Properties on Tilting-pad Thrust Bearing Performance
PublicationPolymer lined tilting-pad bearings demonstrate many advantages over traditional bearing systems. Bearings with a polymer layer in comparison with a babbitted layer show, for example: lower value of friction coefficient (important during start/stops), higher fatigue strength of the coating, better distribution of the load on individual pads due to lower elasticity of the polymers, wider range of operational temperatures or the ability...
-
The application of magnetic fluids in sealing nodes designed for operation in difficult conditions and in machines used in sea environment
PublicationPresented in article MF seals are being researched for sea technology purposes due to their excellent tightness and low resistance of motion. These features are most valuable for ring propellers and ship's main propeller shaft. There are more reasons why technologists payf significant attention for various MFseals applications in their difficult operating conditions. For instance, an advanced pumping systems are designed with contactless...
-
The application of magnetic fluids in sealing nodes designed for operation in difficult conditions and in machines used in sea environment
PublicationPresented in article MF seals are being researched for sea technology purposes due to their excellenttightness and low resistance of motion. These features are most valuable for ring propellers and ship'smain propeller shaft. There are more reasons why technologists payf significant attention for various MFseals applications in their difficult operating conditions. For instance, an advanced pumping systemsare designed with contactless...
-
Challenges associated with development of AUV - unmanned autonomous underwater vehicles to be operated using the AI-based control systems
PublicationThe last decade has been devoted towards further development of the UUV unmanned underwater vehicles which may be of two types. There are the USV unmanned surface vehicles and UUV unmanned underwater vehicles. There is a growing interest to work out and implement the fully advanced AUV autonomous underwater vehicles. The main drivers towards development of such the vehicles are the technologies of autonomous systems, sensors and...
-
Influence of bitumen type on cracking resistance of asphalt mixtures used in pavement overlays
PublicationCracking is one of the predominant distresses occurring in flexible pavements, especially in old pavements that were rehabilitated with an asphalt overlay. In such cases asphalt mixtures should be designed to ensure high resistance to reflective cracking because new asphalt layers are exposed to existing cracks of the old pavement. The nature of these cracks can be various (transverse, longitudinal as well as crazy cracking). One...
-
NUMERICAL MODEL QUALITY ASSESSMENT OF OFFSHORE WIND TURBINE SUPPORTING STRUCTURE BASED ON EXPERIMENTAL DATA
PublicationAs a structure degrades some changes in its dynamical behavior can be observed, and inversely, observation and evaluation of these dynamical changes of the structure can provide information of structural state of the object. Testing of the real structure, besides of being costly, can cover only limited working states. It is particularly considerable in case of hardly accessible, and randomly/severely dynamically loaded offshore...
-
Modelling Signalised Intersections Reliability of Functioning
PublicationThe article addresses a fundamental aspect of traffic, i.e. the operation of traffic signals at intersections, in reference to the reliability theory. In many cases, when intersections carry substantial amounts of traffic, selecting control parameters to produce satisfactory traffic conditions is quite difficult. Design methods do not cover all possible situations which are the result of intersection geometry and location...
-
Modelling and analysis of a synchronous generator in more electric aircraft power system using Synopsys/Saber simulator = Modelowanie i analiza generatora synchronicznego w systemie elektroenergetycznym nowoczesnego samolotu. Zastosowanie symulatora Synopsys/Saber
PublicationStreszczenie angielskie: A model for studying synchronous machine (SM) dynamic behaviour in more electric aircraft (MEA) power system is developed and implemented in the Synopys/Saber simulation environment. The modelling language MAST has been used to elaborate the SM model. The elaborated model exhibit a network with the same number of external terminals/ports as the real SM, and represents its behaviour in terms of the electrical...