Search
Filters
total: 753
filtered: 691
Search results for: IONIC LIQUID VISCOSITY TEMPERATURE QSPR EXPERIMENTAL
-
Pressure drop of HFE7000 and HFE7100 during flow condensation in minichannels
PublicationAttention is focused on the issues of flow resistance and pressure drop of perspective refrigeration fluids during condensation in the two-phase flow in minichannels. The case of the flow through a cylindrical single channel of 2.3 mm inner diameter was carefully analyzed. Pressure drop tests have been performed in diabatic flow conditions. The effect of heat flux, mass flux, vapour quality and saturation temperature on the two-phase...
-
Influence of Additional Loads on Chosen Gait Parameters and Muscles Activity
PublicationThis paper is devoted to human motion analysis and comparison of chosen kinematics parameters during normal gait with and without additional load in a form of backpack. A stability in both cases were compared in both frontal and sagittal planes, by applying a video tracking system. Experimental tests performed on treadmill, passive markers, placed on volunteers bare skin were used. Additionally, an infra-red camera was employed...
-
Modeling of microstructure evolution during high-temperature oxidation of porous Fe-Cr steels
PublicationResearch on the high-temperature oxidation of metals and alloys is experimentally challenging due to the requirement for long-term corrosion exposure, and in the case of porous alloys, due to their complex internal microstructure. In this study, a corrosion model based on the morphological operations of dilation and erosion has been developed. This approach allows for a utilization of various raster representations of the microstructure...
-
Size-exclusion chromatography for the determination of the boiling point distribution of high-boiling petroleum fractions
PublicationThe paper describes a new procedure for the determination of boiling point distribution of high-boiling petroleum fractions using size exclusion chromatography with refractive index detector. Thus far, the determination of boiling range distribution by chromatography has been accomplished using simulated distillation with gas chromatography with the flame ionization detection. This study revealed that in spite of substantial differences...
-
Effect of bio-polyol molecular weight on the structure and properties of polyurethane-polyisocyanurate (PUR-PIR) foams
PublicationThe increasing interest in polyurethane materials has raised the question of the environmental impact of these materials. For this reason, the scientists aim to find an extremely difficult balance between new material technologies and sustainable development. This work attempts to validate the possibility of replacing petrochemical polyols with previously synthesized bio-polyols and their impact on the structure and properties...
-
Experimental Investigations on the Influence of Coil Arrangement on Melting/Solidification Processes
PublicationThe latent heat thermal energy storage units are very popular because of their high energy density and almost close to constant temperature during the charging/discharging. In the present study has been proposed new shell-and-coil geometry with a shifted coil position to enhance the performance of phase change thermal magazine. The experimental investigations have been performed both for the melting and solidification process of...
-
Titanium lanthanum three oxides decorated magnetic graphene oxide for adsorption of lead ions from aqueous media
PublicationThe current study presents a viable and straightforward method for synthesizing titanium lanthanum three oxide nanoparticles (TiLa) and their decoration onto the ferrous graphene oxide sheets to produce FeGO-TiLa as efficient magnetic adsorbent. Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and vibration sample magnetometer (VSM) were used to evaluate...
-
Experimental and numerical analysis of the pyrolysis dynamics of a single wood particle: presentation of the radiographic technique
PublicationPyrolysis is an oxygen-free process for the thermal decomposition of raw materials. The heat conduction and flow of pyrolysis products (i.e., the gas fraction and liquid vapour generated during pyrolysis) influence the process and products. In this work, the influence of the orientation of wooden particle fibres with respect to the direction of the heat source on the dynamics of the process was investigated, where there were two...
-
Shielded HMSIW-based frequency-tunable self-quadruplexing antenna using different solid/liquid dielectrics
PublicationThis article proposes a frequency-tunable self-quadruplexing antenna based on a shielded half-mode substrate integrated waveguide (S-HMSIW). In order to reduce the size of the HMSIW cavity resonator and to obtain quad-band characteristics, a modied E-shaped slot is engraved on the top of the metal. The experimental validation is carried out after analyzing the data using a circuit model. Flexibility of each resonant frequency is...
-
Aggregation of imidazoacridinones - spectroscopic and microcalorimetric approach
PublicationImidazoacridinones (IA) belong to a group of polycyclic heteroaromatic antitumor compounds. IA create the aggregated form in water solution. Self-association of substances is a very important phenomenon in many fields of applied chemistry. It is also fundamental model reaction of many kinds of molecular interactions such as the micelle formation of amphiphilic substances and the binding of small organic molecules to macromolecules....
-
Influences of grain shape and size distribution on permeability
PublicationThe present study investigates the effects of shape and size distributions of grains on the coefficient of permeability (k). A series of constant head permeability tests were performed to characterize the coefficient of permeability. Three particle size ranges (4.75- 0.075, 1.18- 0.075 and 0.300-0.075 mm) of two different sands (Narli Sand, Crushed Stone Sand) having different shapes were tested in a constant head permeability...
-
Pt-rich intermetallic APt8P2 (A = Ca and La)
PublicationThe combination of experimental and theoretical investigation of two new Pt-rich intermetallic compounds: APt8P2 (A = Ca and La) is presented, including solid-state synthesis, crystal structure determination, physical properties characterization and chemical bonding analysis. APt8P2 was obtained through the high-temperature pellet synthesis. According to both single crystal and powder X-ray diffraction results, APt8P2 crystallize...
-
Experimental study on single phase operation of microjet augmented heat exchanger with enhanced heat transfer surface
PublicationThe article presents experimental investigations on a prototype heat exchanger. Presented research is focused on combined active and passive enhancement techniques of surface modification and microjet impingement. The results were compared to reference plate heat exchanger without microjet impingement. The Wilson plot method was applied to determine the heat transfer coefficients in the single phase operation. The heat exchanger...
-
Crack propoagation in MgO-PSZ ceramic materials
PublicationThe properties of ceramic materials such as elevated hardness, high temperature capability, low coefficient of thermal expansion are of interest for rolling element materials. Widely used ceramic materials in engineering applications are silicon nitride, zirconia and alumina. The paper presents an experimental study of the fatigue life of MgO-PSZ ceramic material in lubricated contact with defined types of cracks. A ceramic angular...
-
Waste Tyres Pyrolysis for Obtaining Limonene
PublicationThis review deals with the technologies of limonene production from waste tyre pyrolysis. Thermal decomposition is attractive for tackling the waste tyre disposal problem, as it enables both: energy to be recovered and limonene to be obtained. This material management recycling of tyres is environmentally more beneficial than the burning of all valuable products, including limonene. Given this recoverability of materials from waste...
-
Organic Acids and Polyphenols Determination in Polish Wines by Ultrasound-Assisted Solvent Extraction of Porous Membrane-Packed Liquid Samples
PublicationIn the near future, Poland is going to have more and more favorable conditions for viticulture. Organic acids and polyphenols are among the most commonly analyzed compounds due to their beneficial properties for human health and their importance in the winemaking process. In this work, a new technique involving ultrasound-assisted solvent extraction of porous membrane-packed liquid samples (UASE-PMLS) was for the first time described...
-
Significant Production of Thermal Energy in Partially Ionized Hyperbolic Tangent Material Based on Ternary Hybrid Nanomaterials
PublicationNanoparticles are frequently used to enhance the thermal performance of numerous materials. This study has many practical applications for activities that have to minimize losses of energy due to several impacts. This study investigates the inclusion of ternary hybrid nanoparticles in a partially ionized hyperbolic tangent liquid passed over a stretched melting surface. The fluid motion equation is presented by considering the...
-
Numerical analysis of vacuum drying of a porous body in the integrated domain
Publicationn the present study, the vacuum drying process of an apple slice is numerically modeled based on a control volume method. Transient two-dimensional Navier– Stokes, energy, moisture, and Luikov equations are solved by numerical coding (Fortran) to simulate the simultaneous heat and mass transfer in the ambient and apple slice, respectively. The privilege of using Luikov's model is that the capillary forces are considered, and a...
-
A Closed Bipolar Electrochemical Cell for the Interrogation of BDD Single Particles: Electrochemical Advanced Oxidation
PublicationA closed bipolar electrochemical cell containing two conductive boron-doped diamond (BDD) particles of size 250 – 350 m, produced by high-pressure high-temperature (HPHT) synthesis, has been used to demonstrate the applicability of single BDD particles for electrochemical oxidative degradation of the dye, methylene blue (MB). The cell is fabricated using stereolithography 3D printing and the BDD particles are located at either...
-
Homogeneous nucleation rate of methane hydrate formation under experimental conditions from seeding simulations
PublicationIn this work, we shall estimate via computer simulations the homogeneous nucleation rate for the methane hydrate at 400 bars for a supercooling of about 35 K. The TIP4P/ICE model and a Lennard-Jones center were used for water and methane, respectively. To estimate the nucleation rate, the seeding technique was employed. Clusters of the methane hydrate of different sizes were inserted into the aqueous phase of a two-phase gas–liquid...
-
Sub‐Nanometer‐Scale Cu9S5 Enables Efficiently Electrochemical Nitrate Reduction to Ammonia
PublicationThe sub-nanometer is a key feature size in materials science. Unlike single-atom and nanomaterials, size effects and inter-component cooperative actions in sub-nanomaterials will effective on its performance is more significant. Here, 0.95 nm ordered arrangement Cu9S5 sub-nanowires (Cu9S5 SNWs) are synthesized through the co-assembly effect of inorganic nuclei (Cu9S5) and clusters (phosphotungstic acid-PTA), achieving a significant...
-
Air-cooled photovoltaic roof tile as an example of the BIPVT system – An experimental study on the energy and exergy performance
PublicationThe air-cooled photovoltaic tile is a subject of presented investigations, which focused on improving the overall system efficiency of PV tiles with heat recovery. The operational efficiency of a PV roof tile, together with the construction optimising the air cooling efficiency, were the main points of plans realized at this research stage. The article describes the experimental research consisting of the assessment of electrical,...
-
Green energy extraction for sustainable development: A novel MPPT technique for hybrid PV-TEG system
PublicationThe Photovoltaic (PV) module converts only a small portion of irradiance into electrical energy. Most of the solar energy is wasted as heat, resulting in a rise in PV cell temperature and a decrease in solar cell efficiency. One way to harvest this freely available solar thermal energy and improve PV cell efficiency is by integrating PV systems with thermoelectric generators (TEG). This cogeneration approach of the hybrid PV-TEG...
-
Diagnostic Analysis of Exhaust Gas with A Quick-Changing Temperature from a Marine Diesel Engine Part II / Two Factor Analysis
PublicationThe article presents a continuation of research carried out to determine the effect of input parameters (changes in engine structure parameters) on selected output parameters (diagnostic measures), based on quickly changing exhaust gas temperature. A method of determining the simultaneous influence of two input factors (the structure parameter and the engine load) on one output factor was presented, as well as an evaluation...
-
Nanostructure and dielectric behavior of vanadate glasses containing BaTiO3
PublicationThe ac and dc electrical conductivity of barium titanate doped bismuth-vanadate as-quenched and heat-treated materials was measured in the frequency range from 1 mHz to 1 MHz and in the temperature range from 153 K to 423 K with the impedance spectroscopy method. The microstructure was investigated by means of XRD, scanning electron microscopy (SEM), atomic force microscopy (AFM) and confocal microscopy. The obtained results showed...
-
LCF behavior of 2024AA under uni- and biaxial loading taking into account creep pre-deformation
PublicationThis study presents the results of experimental low-cycle fatigue (LCF) tests of aluminum 2024 alloy T3511 temper in uni- and biaxial loading states. Tests were carried out on both the as-received material (hardened extruded rods) and material with different pre-deformation histories. These deformations were carried out in the creep process at 200 °C and 300 °C for two different levels of at each temperature. The pre-deformed material’s...
-
Modelling of heat transfer in supercritical pressure recuperators
PublicationIn the paper presented is analysis of convective flow heat transfer at supercritical pressure in channels of heat exchanger working in the thermodynamic cycle. The modelling is based on the division of the flow into three regions, namely the heavy fluid, a two phase flow consisting of the heavy and light fluids and finally the light fluid flow. Modelling is concentrated on the region of simultaneous flow of two fluids divided into...
-
Absorptive Desulfurization of Model Biogas Stream Using Choline Chloride-Based Deep Eutectic Solvents
PublicationThe paper presents a synthesis of deep eutectic solvents (DESs) based on choline chloride (ChCl) as hydrogen bond acceptor and phenol (Ph), glycol ethylene (EG), and levulinic acid (Lev) as hydrogen bond donors in 1:2 molar ratio. DESs were successfully used as absorption solvents for removal of dimethyl disulfide (DMDS) from model biogas steam. Several parameters affecting the absorption capacity and absorption rate have been...
-
Towards Computer-Aided Graphene Covered TiO2-Cu/(CuxOy) Composite Design for the Purpose of Photoinduced Hydrogen Evolution
PublicationIn search a hydrogen source, we synthesized TiO2-Cu-graphene composite photocatalyst for hydrogen evolution. The catalyst is a new and unique material as it consists of copper-decorated TiO2 particles covered tightly in graphene and obtained in a fluidized bed reactor. Both, reduction of copper from Cu(CH3COO) at the surface of TiO2 particles and covering of TiO2-Cu in graphene thin layer by Chemical Vapour Deposition (CVD) were...
-
Slowly-closing valve behaviour during steam machine accelerated start-up
PublicationThe paper discusses the state of stress in a slowly-closing valve during accelerated start-up of a steam turbine. The valve is one of the first components affected by high temperature gradients and is a key element on which the power, efficiency and safety of the steam system depend. The authors calibrated the valve model based on experimental data and then performed extended Thermal-FSI analyses relative to experiment. The issue...
-
New approaches for improving selectivity and sensitivity of resistive gas sensors: a review
PublicationPurpose – This paper aims to present the methods of improving selectivity and sensitivity of resistance gas sensors. Design/methodology/approach – This paper compares various methods of improving gas sensing by temperature modulation, UV irradiation or fluctuation-enhanced sensing. The authors analyze low-frequency resistance fluctuations in commercial Taguchi gas sensors and the recently developed tungsten trioxide (WO3) gas-sensing...
-
Characterization of single-stranded DNA-binding proteins from the psychrophilic bacteria Desulfotalea psychrophila, Flavobacterium psychrophilum, Psychrobacter arcticus, Psychrobacter cryohalolentis, Psychromonas ingrahamii, Psychroflexus torquis, and Photobacterium profundum
PublicationBackground: Single-stranded DNA-binding proteins (SSBs) play essential roles in DNA replication, recombination and repair in Bacteria, Archaea and Eukarya. In recent years, there has been an increasing interest in SSBs, since they find numerous applications in diverse molecular biology and analytical methods. Results: We report the characterization of single-stranded DNA-binding proteins from the psychrophilic bacteria Desulfotalea...
-
Nanocrystalline diamond microelectrode on fused silica optical fibers for electrochemical and optical sensing
PublicationFabrication process of thin boron-doped nanocrystalline diamond (B-NCD) microelectrode on fused silica single mode optical fiber has been investigated. The B-NCD films were deposited on the fibers using Microwave Plasma Assisted Chemical Vapor Deposition (MW PA CVD) at glass substrate temperature of 475 ºC. We have obtained homogenous, continuous and polycrystalline surface morphology with the mean grain size in the range of 100-250...
-
Opto-Electrochemical Sensing Device Based on Long-Period Grating Coated with Boron-Doped Diamond Thin Film
PublicationThe fabrication process of thin boron-doped nanocrystalline diamond (B-NCD) microelectrodes on fused silica single mode optical fiber cladding has been investigated. The B-NCD films were deposited on the fibers using Microwave Plasma Assisted Chemical Vapor Deposition (MW PA CVD) at glass substrate temperature of 475 ºC. We have obtained homogenous, continuous and polycrystalline surface morphology with high sp3 content in B-NCD...
-
Insight into Potassium Vanadates as Visible-Light-Driven Photocatalysts: Synthesis of V(IV)-Rich Nano/Microstructures for the Photodegradation of Methylene Blue
PublicationPhotocatalysis is regarded as a promising tool for wastewater remediation. In recent years, many studies have focused on investigating novel photocatalysts driven by visible light. In this study, K2V6O16·nH2O nanobelts and KV3O8 microplatelets were synthesized and investigated as photocatalysts. Samples were obtained via the facile method based on liquid-phase exfoliation with ion exchange. By changing the synthesis temperature...
-
Cavitation-Based Processes for Water and Wastewater Treatment
PublicationCavitation based on advanced oxidation processes (Cav-AOPs) is interesting alternatives for already implemented wastewater treatment technologies. Destructive and strongly undesirable phenomena in the industry, i.e., cavitation, revealed to be useful in a positive manner as a source of energy for chemical reactions. During the implosion of cavitation bubbles, focused energy and resulting high temperature and pressure allows to...
-
Application of mechanistic and data-driven models for nitrogen removal in wastewater treatment systems
PublicationIn this dissertation, the application of mechanistic and data-driven models in nitrogen removal systems including nitrification and deammonification processes was evaluated. In particular, the influential parameters on the activity of the Nitrospira activity were assessed using response surface methodology (RSM). Various long-term biomass washout experiments were operated in two parallel sequencing batch reactor (SBR) with a different...
-
Synergism of floated paperboard sludge cake /sewage sludge for maximizing biomethane yield and biochar recovery from digestate: A step towards circular economy
PublicationAnaerobic digestion of floated paperboard sludge (PS) cake suffers from volatile fatty acids (VFAs) accumulation, nutrient unbalanced condition, and generation of digestate with a risk of secondary pollution. To overcome these drawbacks, sewage sludge (SS) was added to PS cake for biogas recovery improvement under a co-digestion process followed by the thermal treatment of solid fraction of digestate for biochar production. Batch...
-
Assessment of FSW Welds Made of Aluminum Alloy AW7075-T651.
PublicationThis paper summarizes the results of experimental studies in which the aluminum alloy AW7075-T651 was friction stir welded (FSW) using various combinations of process parameters (rotational - R and travel speed - T). Mechanical properties of the test welds were assessed by using static tensile test and Vickers hardness measurement. The temperature of the welded plates was monitored during welding by means of thermocouples placed...
-
ROSANNE Project: New Procedure for Noise Characterisation of Road Surfaces in Europe
PublicationROSANNE is a collaborative project in the 7th EU Framework Programme which aims at harmonising measurement methods for skid resistance, noise emission and rolling resistance of road pavements as a preparation for standardization. The project started in November 2013 and is developing and improving standards in the field of working group CEN/TC 227/WG 5. Regarding the influence of the pavement on the road traffic noise emission,...
-
Generalized Einstein relation in disordered organic semiconductors: Influence of the acoustic phonons–charge carriers scattering
PublicationIn this work, we analyze the generalized Einstein relation for disordered organic semiconductors with a non-equilibrium Druyvesteyn-type distribution function. The Druyvesteyn behavior of hot electrons in a solid state is associated with the acoustic phonons–charge carriers scattering. Such a case has been experimentally demonstrated in electroluminescent inorganic rare–earth–doped zinc chalcogenides. Therefore, we can assume that,...
-
Pressure effects on the electronic structure and superconductivity of (TaNb)0.67(HfZrTi)0.33 high entropy alloy
PublicationEffects of pressure on the electronic structure, electron-phonon interaction, and superconductivity of the high entropy alloy ( TaNb ) 0.67 ( HfZrTi ) 0.33 are studied in the pressure range 0–100 GPa. The electronic structure is calculated using the Korringa-Kohn-Rostoker method with the coherent potential approximation. Effects of pressure on the lattice dynamics are simulated using the Debye-Grüneisen model and the Grüneisen...
-
Immittance Studies of Bi6Fe2Ti3O18 Ceramics
PublicationResults of studies focusing on the electric behavior of Bi6Fe2Ti3O18 (BFTO) ceramics are reported. BFTO ceramics were fabricated by solid state reaction methods. The simple oxides Bi2O3, TiO2, and Fe2O3 were used as starting materials. Immittance spectroscopy was chosen as a method to characterize electric and dielectric properties of polycrystalline ceramics. The experimental data were measured in the frequency range D = (101–107)...
-
Novel Vision Monitoring Method Based on Multi Light Points for Space-Time Analysis of Overhead Contact Line Displacements
PublicationThe article presents an innovative vision monitoring method of overhead contact line (OCL) displacement, which utilizes a set of LED light points installed along it. A light point is an, LED fed from a battery. Displacements of the LED points, recorded by a camera, are interpreted as a change of OCL shape in time and space. The vision system comprises a camera, properly situated with respect to the OCL, which is capable of capturing...
-
Environmental Role of Rime Chemistry at Selected Mountain Sites in Poland
PublicationThe results of field experiments on fog pollutantdeposition enhanced by local mountain climate, completed by thedendrochronological analysis of the forest response, are presentedin this paper. In spite of their low absolute altitude (1,000-1,600 ma.s.l), the Sudetes and the Silesian Beskid form a noticeable orographicbarrier for the airflow of the humid Atlantic air masses.This results in the increase of cloudiness and fog frequency...
-
Phototransformation of Amlodipine: Degradation Kinetics and Identification of Its Photoproducts
PublicationNowadays, monitoring focuses on the primary compounds and does not include degradation products formed during various biological and chemical processes. Transformation products may have the same effects to human health and the environment or sometimes they can be more toxic than the parent compound. Unfortunately, knowledge about the formation of degradation products is still limited, however, can be very important for the environmental...
-
Assessment of thermal and electrical performance of flat plate air-cooled photovoltaic roof tile – experimental and numerical studies
PublicationThe current state of development of the solar energy sector necessitates a new form of incentive for entities to invest in photovoltaic (PV) installations. Building-integrated photovoltaic/thermal (BIPV/T) systems are gaining increasing interest. Effective methods for heat recovery from BIPV/T collectors are searched for. Presented research experimentally and numerically considered the influence of cooling conditions on the electrical...
-
Flow boiling intensification in minichannels by means of mechanical flow turbulising inserts
PublicationThe work presents the results of experimental investigation on heat transfer in minichannels. Refrigerant R123 was used as a test fluid. Single vertical silver tubes of 380 mm length and 2.3 mm diameter were examined with two variants of turbulising inserts. A wide range of parameters was considered, namely mass flux G=534-3011 kg/(m2s), heat flux qw=28.5-68.4 kW/m2, saturation temperature Tsat=23-86 stC and the full range of vapour...
-
Effects of Noncontact Shoulder Tool Velocities on Friction Stir Joining of Polyamide 6 (PA6)
PublicationIn this study, the effects of the traverse and rotational velocities of the noncontact shoulder tool on the heat generation and heated flux during the friction stir joining of high-density polyamide 6 (PA6) polymer were investigated. The computational fluid dynamics (CFD) method was employed to simulate the thermomechanical phenomena during the friction stir joining (FSJ) process of PA6. A developed model was used to consider the...
-
Reactive imines: Addition of 2-aminopyrimidine to the imine bond and isolation of the aminal from the equilibrium mixture aminal/imine
PublicationThe reaction between o-vanillin and 2-aminopyrimidine leads to the formation of a single crystalline product: aminal, 1, which results from the reaction of the initially formed imine with 2-aminopyrimidine. The reaction was followed by the NMR spectroscopy. VT NMR studies prove that in solution two major species are observed: aminal and imine and their ratio depends on the time or/and temperature with the imine content increasing...