Search
Filters
total: 397
filtered: 237
Search results for: SIGNAL SAMPLING
-
Derivation of motor mean phase currents in PMSM drives operating with low switching-to-fundamental frequency ratio
PublicationPulse width modulation (PWM) of inverter output voltage causes the waveforms of motor phase cur-rents to consist of distinctive ripples. In order to provide suitable feedback for the motor current con-trollers, the mean value must be extracted from the currents’ waveforms in every PWM cycle. A com-mon solution to derive the mean phase currents is to sample their value at the midpoint of a symmetrical PWM cycle. Using an assumption...
-
Online Volatile Compound Emissions Analysis Using a Microchamber/Thermal Extractor Coupled to Proton Transfer Reaction-Mass Spectrometry
PublicationIndoor air is a complex and dynamic mixture comprising manifold volatile organic compounds (VOCs) that may cause physiological and/or psychological discomfort, depending on the nature of exposure. This technical note presents a novel approach to analyze VOC emissions by coupling a microchamber/thermal extractor (μ-CTE) system to a proton transfer reaction-mass spectrometer (PTR-MS). This configuration provides an alternative to...
-
Ellipse-fitting algorithm implementation in the impedance measurement system based on DAQ card with FPGA
PublicationThe paper presents an implementation of the ellipse-fitting algorithm in the impedance measurement system based on DAQ card equipped with FPGA chip. The method implementation was tested by simulation means as well as experimentally in the designed and presented measurement system. Finally, the limit values of sampling parameters which assures satisfying accuracy were given.
-
Application of passive sampling technique in monitoring research on quality of atmospheric air in the area of Tczew, Poland.
PublicationThis paper presents the results of atmospheric air quality research in Tczew (adjacent to the Vistula River) on the content of BTEX compounds. Analytical procedure applied during the sampling of the analytes from the air used the passive sampling technique (diffusive passive sampler, Radiello®). For determination of BTEX compounds in atmospheric air, two-stage thermal desorption technique combined with gas chromatography (TD-GC-FID)...
-
Analytical Techniques Used in Monitoring of Atmospheric Air Pollutants
PublicationThe air pollution monitoring is one of the most pressing environmental problems today. The paper describes common air pollutants, their interaction and impact on the environment, and classifies the techniques and methods applied in air studies. Furthermore, the review characterizes the selected collection and sampling techniques used for gas sample analysis. Finally, the schematic diagrams of typical designs of systems applied...
-
Polyethylene glycol-coated solid-phase microextraction fibres for the extraction of polar analytes-A review
PublicationThe article discusses the merits and limitations of commercially available solid-phase microextraction (SPME) fibres and compares them with the new type of extraction coatings, in particular those containing polyethylene glycol as sorbent, as well as the methods of the preparation of the latter. It also analyses their possible application for the extraction of a broad spectrum of analytes, with particular emphasis on the sampling...
-
Sea spray as a secondary source of chlorinated persistent organic pollutants? - Conclusions from a comparison of seven fresh snowfall events in 2019 and 2021
PublicationSecondary sources of persistent organic pollutants (POPs) gain in importance worldwide as primary sources decline. In this work, we aim to determine whether sea spray may be a secondary source of chlorinated POPs to the terrestrial Arctic, since a similar mechanism was proposed there only for the more water-soluble POPs. To this end, we have determined polychlorinated biphenyls and organochlorine pesticides concentrations in fresh...
-
Quality of Analytical Results: Classifiying Errors and Estimating Measurement Uncertainty
PublicationThe most important parameter of each analytical result is its reliability. An analytical result is not a constant value; each result has two properties, error and uncertainty. The sources of both these parameters have to be known and their values determined (estimated). All analytical results are obtained by applying an appropriate measuring procedure. The need for reliable results requires application of reliable analytical procedures,...
-
Determination of volatile organic compounds in water samples using membrane-solid phase microextraction (M-SPME) (headspace version)
PublicationThe results of a study on the use of membrane-solid phase microextraction (M-SPME) for sampling volatile organic compounds (VOCs) from the headspace above the liquid medium are presented. The sampled VOCs were subsequently quantified by gas chromatography (GC). Two systems were compared in this study, i.e. a novel two-phase sorption system (M-SPME), and a commercial fibre. Headspace sampling using SPME was optimized with respect...
-
Current trends in solid-phase microextraction (SPME) fibre catings
PublicationThis critical review presents information on known and innovative approaches to the manufacture of fibre coatings used in solid-phase microextraction (SPME). The properties, advantages and drawbacks of the different types of commercially available SPME fibre coatings are discussed in detail, as are those of novel types of coatings and the methodologies of their preparation. The applications of fibre coatings in the solid-phase...
-
Usage of Two-Center Basis Function Neural Classifiers in Compact Smart Resistive Sensors
PublicationA new solution of the smart resistance sensorwith the Two-Center Basis Function (TCBF) neuralclassifier, for which the resistance sensor is a component ofan anti-aliasing filter of an ADC is proposed. Thetemperature measurement procedure is based on excitationof the filter by square impulses, sampling time response ofthe filter and processing measured voltage values by theTCBF classifier. All steps of the measurement procedure...
-
Direct algorithm for optimizing robust MPC of drinking water distribution systems hydraulics
PublicationModel-based predictive control is an effective method for control the large scale systems [1]–[6], [8], [16], [17]. Method is based on on-line solution of the control task over the control horizon using current and past measurements, as well as the system model. Only a first element of calculated control sequence is applied to the plant. At the next sampling instant, based on new process output measurements, control procedure is...
-
Adaptive CAD-Model Construction Schemes
PublicationTwo advanced surrogate model construction techniques are discussed in this paper. The models employ radial basis function (RBF)interpolation scheme or artificial neural networks (ANN) with a new training algorithm. Adaptive sampling technique is applied withrespect to all variables. Histograms showing the quality of the models are presented. While the quality of RBF models is satisfactory, theperformance of the ANN models obtained...
-
Optical Sensor Based Gestures Inference Using Recurrent Neural Network in Mobile Conditions
PublicationIn this paper the implementation of recurrent neural network models for hand gesture recognition on edge devices was performed. The models were trained with 27 hand gestures recorded with the use of a linear optical sensor consisting of 8 photodiodes and 4 LEDs. Different models, trained off-line, were tested in terms of different network topologies (different number of neurons and layers) and different effective sampling frequency...
-
Evaluation of the fast impedance spectroscopy method in the laboratory measurement system
PublicationIn this paper the method for fast impedancespectroscopy of technical objects with very high impedance(|Zx| ≥ 1 GΩ) is evaluated by means of simulation and practicalexperiment. The method is based on excitation of an object, witha square pulse and measurements of voltage and currentresponses with DAQ card. The object impedance spectrum isobtained with use of continuous Fourier transform. Someimprovements of the method concerned...
-
DEVELOPMENT OF THE ALGORITHM OF POLISH LANGUAGE FILM REVIEWS PREPROCESSING
PublicationThe algorithm and the software for conducting the procedure of Preprocessing of the reviews of films in the Polish language were developed. This algorithm contains the following steps: Text Adaptation Procedure; Procedure of Tokenization; Procedure of Transforming Words into the Byte Format; Part-of-Speech Tagging; Stemming / Lemmatization Procedure; Presentation of Documents in the Vector Form (Vector Space Model) Procedure; Forming...
-
Solid Phase Microextraction: Apparatus, Sorbent Materials, and Application.
Publicationhe primary objective of this review article is to strategically screen and highlight the advancements in the area of solid phase microextraction (SPME). The plenty of review articles have been written on different aspects of SPME, this review is dedicated to provide the brief but clear overview of the research footprints so produced from SPME. Some of the key advancements in types and designs, coating materials, coating strategies,...
-
Influence of preprocessing techniques on pulse pressure velocity determination
PublicationPulse Wave Velocity (PWV) is measured and utilized in many clinical applications. Recently, a wide research has been led to develop a cuff-less and continuous blood pressure method basing on PWV. However, in this application a decision on choosing an appropriate fiducial point of pulse wave (PW) waveform is necessary and substantial. It would allow to measure time parameters necessary to determine PWV. An influence of sampling...
-
Zmiana szybkości próbkowania z zastosowaniem filtrów I-FIR
PublicationW pracy omówiono zagadnienie projektowania filtrów I-FIR (Interpolated FIR) na potrzeby algorytmu zmiany szybkości próbkowania (SRC - Sampling Rate Conversion). Przeprowadzono analizę skutków zastosowania filtrów I-FIR, ze szczególnym uwzględnieniem analizy wydajności numerycznej implementacji algorytmów SRC realizujących konwersję pomiędzy standardem szybkości próbkowania CD i DAT. Na koniec opracowano i przeanalizowano warianty...
-
Errors of a Linear Current Approximation in High-Speed PMSM Drives
PublicationCurrent sampling techniques and predictive algorithms used in the digital control of electric drives rely on a simple mathematical model that assumes linear current changes upon constant supplying voltages. This paper identifies rotor movement as a factor that makes this assumption invalid when the rotor covers an angular distance of a few tens of degrees during the control interval duration. The errors of the linear current approximation...
-
Analysis of antibiotic resistance in Escherichia coli isolated from the Reda River and the Oliwski Stream using basic statistical methods = Zastosowanie metod ststystycznych do analizy antybiotykoodporności bakterii wskaźnikowych pochodzących z rzeki Redy i Potoku Oliwskiego
PublicationIn this study distribution of antimicrobial resistance patterns among fecal indicator bacteria (Escherichia coli and Enterococcus spp.) was examined in two watercourses. The susceptibility analyses were carried out against the antimicrobial agents, important in treating human E. coli and enterococcal infection. Water samples were obtained from the Oliwski Stream and from the Reda River. On each watercourse the five representative...
-
Seagrass vegetation and meiofauna enhance the bacterial abundance in the Baltic Sea sediments (Puck Bay)
PublicationThis study presents the first report on bacterial communities in the sediments of eelgrass (Zostera marina) meadows in the shallow southern Baltic Sea (Puck Bay). Total bacterial cell numbers (TBNs) and bacteria biomass (BBM) assessed with the use of epifluorescence microscope and Norland’s formula were compared between bare and vegetated sediments at two localities and in two sampling summer months. Significantly higher TBNs and...
-
Pikselowy cyfrowy układ CDS przeznaczony do przetwornika obrazu CMOS
PublicationW artykule zaproponowano cyfrowy układ CDS (Correlated Double Sampling) przeznaczony do przetwornika obrazu CMOS. Układ różni się od klasycznych rozwiązań tym, że dwie pamięci przechowujące próbki sygnału wizyjnego zastąpiono jednym licznikiem rewersyjnym. Dzięki tej modyfikacji możliwa jest znaczna redukcja powierzchni układu CDS i umieszczenie go w każdym pikselu przetwornika obrazu CMOS. System został zaprojektowany i przesymulowany...
-
Pikselowy cyfrowy układ CDS przeznaczony do przetwornika obrazu CMOS
PublicationW artykule zaproponowano cyfrowy układ CDS (Correlated Double Sampling) przeznaczony do przetwornika obrazu CMOS. Układ różni się od klasycznych rozwiązań tym, że dwie pamięci przechowujące próbki sygnału wizyjnego zastąpiono jednym licznikiem rewersyjnym. Dzięki tej modyfikacji możliwa jest znaczna redukcja powierzchni układu CDS i umieszczenie go w każdym pikselu przetwornika obrazu CMOS. System został zaprojektowany i przesymulowany...
-
Employment of passive sampling in monitoring indoor air quality in selected residences in a Tri-city area in Poland
PublicationTime-weighted average concentrations of selected volatile compounds were measured in chosen residences in a Tri-City area of Poland by means of passive sampling. The results were compared to those obtained by dynamic technique – sorption tubes filled with Tenax TA sorbent. Results obtained by employing the two techniques were similar. Total volatile organic compound (TVOC) parameters were also determined. An attempt was also...
-
Local variability in snow concentrations of chlorinated persistent organic pollutants as a source of large uncertainty in interpreting spatial patterns at all scales
PublicationSingle point sampling, a widespread practice in snow studies in remote areas, due to logistical constraints, can present an unquantified error to the final study results. The low concentrations of studied chemicals, such as chlorinated persistent organic pollutants, contribute to the uncertainty. We conducted a field experiment in the Arctic to estimate the error stemming from differences in the composition of snow at short distances...
-
Distribution of volatile organohalogen compounds in petrochemical plant water streams
PublicationThe study assesses halogenated volatile organic compound concentrations in the water and wastewaterstreams of a petrochemical plant. Water samples were collected at 11 sampling points during 5 samplingcampaigns. The samples were collected from the oil dewaxing unit and in the wastewater treatmentplant. Dichloromethane and 1,2-dichloroethane were the most frequently determined compounds. Tetrachloroethenewas also detected at the...
-
Evaluating Performance and Accuracy Improvements for Attention-OCR
PublicationIn this paper we evaluated a set of potential improvements to the successful Attention-OCR architecture, designed to predict multiline text from unconstrained scenes in real-world images. We investigated the impact of several optimizations on model’s accuracy, including employing dynamic RNNs (Recurrent Neural Networks), scheduled sampling, BiLSTM (Bidirectional Long Short-Term Memory) and a modified attention model. BiLSTM was...
-
Neural network based algorithm for hand gesture detection in a low-cost microprocessor applications
PublicationIn this paper the simple architecture of neural network for hand gesture classification was presented. The network classifies the previously calculated parameters of EMG signals. The main goal of this project was to develop simple solution that is not computationally complex and can be implemented on microprocessors in low-cost 3D printed prosthetic arms. As the part of conducted research the data set EMG signals corresponding...
-
TS-based RSM-aided design of cold-formed steel stiffened C-sectional columns susceptible to buckling
PublicationThe paper focuses on joint-performance analysis of a built-up cold-formed thin-walled C-sectional column with a fillister (stiffener) of the same type, interconnected with a series of bolts located along the length of the compressed members in specific spacing. The quantity of bolts and the non-connected starting distance of the fillister are considered random variables of the problem. Optimal distribution of joints on the stiffener...
-
A novel hybrid adaptive framework for support vector machine-based reliability analysis: A comparative study
PublicationThis study presents an innovative hybrid Adaptive Support Vector Machine - Monte Carlo Simulation (ASVM-MCS) framework for reliability analysis in complex engineering structures. These structures often involve highly nonlinear implicit functions, making traditional gradient-based first or second order reliability algorithms and Monte Carlo Simulation (MCS) time-consuming. The application of surrogate models has proven effective...
-
Global Surrogate Modeling by Neural Network-Based Model Uncertainty
PublicationThis work proposes a novel adaptive global surrogate modeling algorithm which uses two neural networks, one for prediction and the other for the model uncertainty. Specifically, the algorithm proceeds in cycles and adaptively enhances the neural network-based surrogate model by selecting the next sampling points guided by an auxiliary neural network approximation of the spatial error. The proposed algorithm is tested numerically...
-
Analytical procedures for determination of cocaine and its metabolites in biological samples
PublicationThe dangerous effects and increased usage of illicit drugs have inspired the development of analytical methodologies. We based our review of analytical procedures for determination of cocaine (COC) and its metabolites on literature from the past two decades. Our main aim was to compare the capabilities of different analytical techniques. The diversity of matrices from which COC is determined (e.g., blood, hair, saliva, plasma,...
-
Complex Root Finding Algorithm Based on Delaunay Triangulation
PublicationA simple and flexible algorithm for finding zeros of a complex function is presented. An arbitrary-shaped search region can be considered and a very wide class of functions can be analyzed, including those containing singular points or even branch cuts. The proposed technique is based on sampling the function at nodes of a regular or a self-adaptive mesh and on the analysis of the function sign changes. As a result, a set of candidate points...
-
Experimental certification of an informationally complete quantum measurement in a device-independent protocol
PublicationMinimal informationally complete positive operator-valued measures (MIC-POVMs) are special kinds of measurement in quantum theory in which the statistics of their d2-outcomes are enough to reconstruct any d-dimensional quantum state. For this reason, MIC-POVMs are referred to as standard measurements for quantum information.Here, we report an experiment with entangled photon pairs that certifies, for what we believe is the first...
-
Evolutionary music composition system with statistically modeled criteria
PublicationThe paper concerns an original evolutionary music composition system. On the basis of available solutions, we have selected a finite set of music features which appear to have a key impact on the quality of composed musical phrases. Evaluation criteria have been divided into rule-based and statistical sub-sets. Elements of the cost function are modeled using a Gaussian distribution defined by the expected value and variance obtained...
-
Realizacja przetwornika obrazu CMOS z wbudowaną konwersją A/C i cyfrowym układem CDS
PublicationW artykule przedstawiono realizację w technologii CMOS 180 nm przetwornika obrazu z wbudowaną konwersją analogowo-cyfrową oraz z funkcją cyfrowej redukcji szumu. Przedstawiona realizacja przetwornika obrazu różni się od znanych z literatury rozwiązań tym, że układ redukcji szumu CDS (Correlated Double Sampling) umieszczono w każdym pikselu obrazu. Dzięki tej modyfikacji możliwe jest zastąpienie migawki szczelinowej przez migawkę...
-
The home-made in situ passive flux sampler for the measurement of monoterpene emission flux: preliminary studies
PublicationThe paper presents the construction and metrological characteristics of the home-made in situ passive flux sampler, an analytical tool representing small-scale emission chambers working in situ and passively sampling analytes from the gaseous phase. The sorption element was a cylindrical container made of stainless steel net, packed with a carbon sorbent bed-graphitized charcoal, Carbograph 4 (35/50mesh). The recommended working/exposure...
-
Global Complex Roots and Poles Finding Algorithm Based on Phase Analysis for Propagation and Radiation Problems
PublicationA flexible and effective algorithm for complex roots and poles finding is presented. A wide class of analytic functions can be analyzed, and any arbitrarily shaped search region can be considered. The method is very simple and intuitive. It is based on sampling a function at the nodes of a regular mesh, and on the analysis of the function phase. As a result, a set of candidate regions is created and then the roots/poles are verified...
-
Trace elements content of surface peat deposits in the Solovetsky Islands (White Sea)
PublicationPeatlands form environmental archives of trace element deposition. In this regard they are particularly valuable for areas such as the Arctic, where regular pollution monitoring is either impossible or extremely costly. The aim of this study was to assess pollution in the Solovetsky Islands (65° 05' N, 35° 53' E) by examining the spatial variability in trace element content of the uppermost layer of peat, immediately below the...
-
Volatile Compound Emissions from Stereolithography Three-Dimensional Printed Cured Resin Models for Biomedical Applications
PublicationStereolithography three-dimensional printing is used increasingly in biomedical applications to create components for use in healthcare and therapy. The exposure of patients to volatile organic compounds (VOCs) emitted from cured resins represents an element of concern in such applications. Here, we investigate the biocompatibility in relation to inhalation exposure of volatile emissions of three different cured commercial resins...
-
The occurrence of heavy metals and metal-resistant bacteria in water and bottom sediments of the Straszyn reservoir (Poland)
PublicationThe aim of this study is investigate the distribution of selected heavy metals (zinc, copper, lead, cadmium) and metal-resistant bacteria in water and bottom sediments of drinking water reservoir for Gdańsk (Poland). The research area - Straszyn Lake is a dam reservoir on Radunia river, of the total volume of 3 mln m3. Sediment and water sampling took place between May and October 2013 (eight series). Regarding metal concentration...
-
Survey of ICT students' views on self-assessment of professional preparation after remote study
PublicationThe contemporary post-pandemic reality is characterised by an undisputable shift toward remote education and work. The aim of this article is to identify the assessment of ICT evaluation of different forms of study, including desktop, remote and hybrid forms; to find out their preferences towards different forms of education and work, and to determine their sense of self-efficacy in terms of professional tasks undertaken after...
-
Comparison of Evaluation of Air Odour Quality in Vicinity of Petroleum Plant Using a Prototype of Electronic Nose Instrument and Fast GC Technique
PublicationThe paper presents the results of investigation on classification of the ambient air samples collected in a vicinity of the LOTOS Group S.A. petroleum plant with respect to odour. The investigations were carried out with an electronic nose prototype and a commercial electronic nose of Fast GC-type – HERACLES II. The prototype was equipped with a set of six semiconductor sensors by FIGARO Co. and a photoionization sensor of PID-type....
-
Effect of Impoundment on Physico-chemical Properties of Water in the Flowing through stream, the Case of the Turawa Reservoir
PublicationThe Turawa reservoir is one of the most important storage reservoirs in Poland. Quite many physico-chemical parameters of water in the reservoir itself and also in the Mała Panew, the river flowing through the reservoir were measured at various periods of the year. Measuring and sampling points were situated at the river inflow, over the reservoir, and at the river outflow. The parameters included temperature, electrical conductivity,...
-
Main complications connected with detection, identification and determination of trace organic constituents in complex matrix samples
PublicationIt is well known that some problems with the determination of organic analytes at trace level can occur. This issue is connected with contamination during each stage of the analytical procedure from sampling to sample preparation up to chromatographic analysis, which often leads to false-positive or overestimated results. Another problem associated with determination of analytes occurs at trace- and ultra-trace level is a background...
-
THE SITUATION OF WOMEN IN THE POLISH LABOUR MARKET IN THE LIGHT OF CHANGES IN THE PENSION SECURITY SYSTEM
PublicationThe aim of the study is to examine the opinion of a group of women on their economic activity and decisions related to retirement. The first part of the article reviews previous research related to the economic activity of older people with a special focus on women. In the empirical part of the article, women’s opinions on issues related to retirement were analyzed. The research was carried out in 2016 on a sample of 45 women,...
-
Dynamic Headspace Sampling as an Initial Step for Sample Preparation in Chromatographic Analysis
PublicationThis work represents a brief summary of the use of dynamic headspace (DHS) as a technique for sample preparation in chromatographic analysis. Despite numerous developments in the area of analyte isolation and enrichment, DHS remains one of the fundamental methods used with GC. In our opinion, interest in this technique will not diminish significantly because it conforms to stipulations of green analytical chemistry. Moreover, DHS...
-
Direct measurements of odorous volatile organic compounds present in biosolids cakes by Proton Transfer Reaction – Mass Spectrometry Technique
PublicationThis paper show the results of investigation of concentration of odorous chemical compounds emitted upon ageing of anaerobically stabilised biosolids that could contribute to the overall odour character of nuisance emissions. Biosolids samples from wastewater treatment plant were collected in spring time. Concentrations of volatile organic compounds using a US EPA flux hood and Proton Transfer Reaction-Time of Flight-Mass Spectrometry...
-
Deep neural networks approach to skin lesions classification — A comparative analysis
PublicationThe paper presents the results of research on the use of Deep Neural Networks (DNN) for automatic classification of the skin lesions. The authors have focused on the most effective kind of DNNs for image processing, namely Convolutional Neural Networks (CNN). In particular, three kinds of CNN were analyzed: VGG19, Residual Networks (ResNet) and the hybrid of VGG19 CNN with the Support Vector Machine (SVM). The research was carried...