Filters
total: 604
Search results for: LOAD TESTING
-
Verification of safety in low-voltage power systems without nuisance tripping of residual current devices
PublicationLow-voltage power systems require initial and periodical verification to check the effectiveness of protection against electric shock. As a protection in case of fault, automatic disconnection of supply is most often used. To verify such a protection measure, the earth fault loop impedance or resistance is measured. This measurement is easy to perform in circuits without residual current devices. When residual current devices are...
-
A testing method of analog parts of mixed-signal electronic systems equipped with the IEEE1149.1 test bus
PublicationA new solution of the JTAG BIST for testing analog circuits in mixed-signal electronic microsystems controlled by microcontrollers and equipped with the IEEE1149.1 bus is presented. It is based on a new fault diagnosis method in which an analog circuit is stimulated by a buffered signal from the TMS line, and the time response of the circuit to this signal is sampled by the ADC equipped with the JTAG. The method can be used for...
-
Reliable testbed for indoor positioning systems
PublicationThis paper proposes a test environment for indoor localization system, based on radio wave propagation prosperities. The following sections presents variety of problems from the assessment of the existing localization system to the analysis of inconveniences which occur when comparison of different localization systems is implemented. The problem is associated with different testing environments presented in published papers is...
-
From U2TP Models to Executable Tests with TTCN-3
PublicationThe approach towards system engineering according to Model-Driven Architectures (MDA) with code generation derived from model implies also an increased need for research on automation of the test generation process. This paper presents an approach to derive executable tests from UML 2.0 Testing Profile diagrams automatically. In particular, an approach to derive executable tests within the Testing and Test Control Notation (TTCN-3)...
-
Validation of a virtual test environment for C2X communication under radio jamming conditions
PublicationIn this paper, we propose a novel car-2-x communication security testing methodology in the physical layer of wireless systems. The approach is dedicated to automated testing of autonomous vehicles and it is essential for such complex systems operation, especially with regard to safety and security issues. It is based on scenario-driven testing in virtual and real test environments created from collected or simulated data. The...
-
Evaluation of possibilities in identification and susceptibility testing for Candida glabrata clinical isolates with the Integral System Yeast Plus (ISYP)
PublicationThe aim of this study was to evaluate possibilities of correct identification and susceptibility testing of C. glabrata clinical isolates with Integral System Yeast Plus (ISYP). For species identification, as the reference method, API Candida test and species-specific PCR reactions were used. The potential of antifungal susceptibility testing by the ISYP test was compared with the Sensititre Yeast One. Whilst the reference methods...
-
Chemical identification of rubber fender sample and hardness and density measurements
PublicationScope of testing: Chemical identification of rubber fender sample and hardness and density measurements. - Raport z badań zleconych - Numer umowy: 031178
-
Classification of high-voltage varistors into groups of differentiated quality
PublicationThe research was aimed on defining a factor of quality for high-voltage varistors using Non-Destructive Testing (NDT) techniques, which could be applied during the production testing. The newly proposed parameter Q determined on the basis of the lowest resonant frequency fr measured within the preselected frequency range was taken into account. The parameter Q was defined for ZnO structures after firing, without metallized contacts....
-
Model-based testing for execution algorithms in the simulation of cyber-physical systems
PublicationThe understanding of simulation semantics of a hybrid system is a challenge for computational engineers as it requires expertise in computer science, engineering, numerical methods, and mathematics at once. The testing methods for the execution of a simulation are being researched but not yet applied on the industrial level. Consequently, the semantics of the simulation becomes a critical artifact in the system development process....
-
Effects of laser pulse duration in two-photon vision threshold measurements
PublicationPulsed near-infrared (NIR) light sources can be successfully applied for both imaging and functional testing of the human eye, as published recently1. These two groups of applications have different requirements. For imaging applications, the most preferable is invisible scanning beam while efficiently visible stimulating beam is preferable for functional testing applications. The functional testing of human eye using NIR laser...
-
From Functional Requirements through Test Evaluation Design to Automatic Test Data Retrieval – a Concept for Testing of Software Dedicated for Hybrid Embedded Systems
PublicationFrom Functional Requirements through Test Evaluation Design to Automatic Test Data Retrieval – a Concept for Testing of Software Dedicated for Hybrid Embedded Systems
-
Diagnostics of high-voltage varistor quality using resonant ultrasound spectroscopy
PublicationResonant spectroscopy is an effective nondestructive testing method focused on defects detection in tested objects. Resonance spectrum contains an information about the mechanical properties and particularly about the structural homogeneity of the whole object. A swept frequency method has been used to measure the selected resonant frequencies range. The system for measurement of resonant ultrasound spectroscopy of high-voltage...
-
Regulacje prawne odnoszące się do testowania samochodów autonomicznych na drogach publicznych w Polsce i w Kalifornii
PublicationThe current level of technological advancement allows for predicting that in the near future autonomous technology may be successfully used for the production of self-driving cars. Many companies (not necessarily related to the automotive sector) have spotted the chance of future profits and thus started working on testing and development of autonomous vehicles. The initiation of work has indicated the lack of possibility to test...
-
Application of TMS320c67xx signal processors for SONIC-self-optimizing narrowband interference canceler
PublicationThe paper presents a laboratory system for testing active control algorithms of acoustics noise in ducts. An applied algorithm - self-optimizing narrowband interference canceller (SONIC), allows one to remove narrowband disturbances of constant or slowly time-varying frequencies. Example experimental results of using the laboratory system for supression of sinusoidal disturbance are described. An electronic part of the system was...
-
METHOD OF TRAINING THE ENDOSCOPIC VIDEO ANALYSIS ALGORITHMS TO MAXIMIZE BOTH ACCURACY AND STABILITY
PublicationIn the article a new training and testing method of endoscopic video analysis algorithms is presented. Classical methods take into account only eciency of recognizing objects on single video frames. Proposed method additionally considers stability of classiers output for real video input. The method is simple and can be trained on data sets created for other solutions. Therefore, it is easily applicable to existing endoscopic video...
-
Application of Complementary Signals in Built-In Self Testers for Mixed-Signal Embedded Electronic Systems
PublicationThis paper concerns the implementation of shape-designed complementary signals (CSs), matched to the frequency characteristic of the circuit under test, in built-in self testers (BISTs), dedicated to mixed-signal embedded electronic systems for testing their analog sections. The essence of the proposed method and solution of CS BIST is low-cost realization on the base of hardware and software resources of microcontrollers used...
-
Self-Testing of Analog Parts Terminated by ADCs Based on Multiple Sampling of Time Responses
PublicationA new approach for self-testing of analog parts terminated by analog-to-digital converters in mixed-signal electronic microsystems controlled by microcontrollers is presented. It is based upon a new fault diagnosis method using a transformation of the set of voltage samples of the time response of a tested analog part to a square impulse into localization curves placed in a multidimensional measurement space. The method can be used...
-
The Effect of Water and Frost on Fatigue Life of Asphalt Concrete
PublicationThis paper presents testing of fatigue life of asphalt concrete that has been subjected to action of water and frost. Simulation of water and frost action was based on the original AASHTO T283 method and its modification. The original method was modified in such a way that instead of a single freeze-thaw cycle, 50 and 150 cycles were applied. Fatigue life was measured in the indirect tensile fatigue test in the Nottingham asphalt...
-
Challenges in operating and testing loop heat pipes in 500–700 K temperature ranges
PublicationThe potential applications of loop heat pipes (LHPs) are the nuclear power space systems, fuel cell thermal management systems, waste heat recovery systems, medium temperature electronic systems, medium temperature military systems, among others. Such applications usually operate in temperature ranges between 500–700 K, hence it is necessary to develop an LHP system that will meet this requirement. Such a thermal management device...
-
Acquisition and indexing of RGB-D recordings for facial expressions and emotion recognition
PublicationIn this paper KinectRecorder comprehensive tool is described which provides for convenient and fast acquisition, indexing and storing of RGB-D video streams from Microsoft Kinect sensor. The application is especially useful as a supporting tool for creation of fully indexed databases of facial expressions and emotions that can be further used for learning and testing of emotion recognition algorithms for affect-aware applications....
-
Using an IEEE1149.1 Test Bus for Fault Diagnosis of Analog Parts of Electronic Embedded Systems
PublicationThe new solution of a BIST called the JTAG BIST for self-testing of analog parts of electronic embedded systems is presented in the paper. The JTAG BIST consists of the BCT8244A and SCANSTA476 integrated circuits of Texas Instruments controlled via the IEEE 1149.1 bus. The BCT8244A is a scan test device with octal buffers, and the SCANSTA476 is a 12-bit ADC with 8 analog input channels. Self-testing approach is based on the fault...
-
Usability Testing of Mobile Applications: A Methodological Framework
PublicationLess than five percent of all mobile applications have become successful throughout 2023. The success of a new mobile application depends on a variety of factors ranging from business understanding, customer value, and perceived quality of use. In this sense, the topic of usability testing of mobile applications is relevant from the point of view of user satisfaction and acceptance. However, the current knowledge seems to be fragmented,...
-
Requirements, modifications and methods of mechanical testing of bone cement – literature review
PublicationThe Aim of the paper is to show the basic requirements for the bone cement, its modifications in terms of physical, mechanical and biological properties and testing methods. This publication is intended to be a source of systematized basic knowledge regarding the modified bone cement.
-
Derivation of Executable Test Models From Embedded System Models using Model Driven Architecture Artefacts - Automotive Domain
PublicationThe approach towards system engineering compliant to Model-Driven Architecture (MDA) implies an increased need for research on the automation of the model-based test generation. This applies especially to embedded real-time system development where safety critical requirements must be met by a system. The following paper presents a methodology to derive basic Simulink test models from Simulink system models so as to execute them...
-
Effect of Variation of Hard Segment Content and Graphene-Based Nanofiller Concentration on Morphological, Thermal, and Mechanical Properties of Polyurethane Nanocomposites
PublicationThis study describes the development of a new class of high-performance polyurethane elastomer nanocomposites containing reduced graphene oxide (RGO) or graphene nanoplatelets (GNP). Two types of polyurethane elastomers with different contents of hard segments (HS) were used as a polymer matrix. The developed nanocomposites were characterized by thermal analysis (DSC, TG), dynamic mechanical testing (DMA), hardness testing, mechanical...
-
The Multiplatform Environment for Simulation and Features Estimation of Mixed-Signal Devices
PublicationThe use of simulation laboratories is gaining popularity in thedomains of engineering programs. However, the experience in teaching showsthat the simulation itself is not very effective in didactic processes. Teachingprocesses in thefield of specialist subjects, designed for students of technicaluniversities, should be based on direct operations performed by the student onreal devices. At the same time, at the later stages of didactic...
-
Affect aware video games
PublicationIn this chapter a problem of affect aware video games is described, including such issue as: emotional model of the player, design, development and UX testing of affect-aware video games, multimodal emotion recognition and a featured review of affect-aware video games.
-
Problematyka dotycząca zapewnienia fotostabilności substancji leczniczych w postaciach leku
PublicationUV and visible radiation may influence on the stability of some active pharmaceutical ingredients and in a consequence destabilizes such medicinal products, causes changesin its physicochemical properties also with negative pharmacological and sometimes even toxic effects. For this reason it is important to conduct the routine testing photostability. The knowledge of chemistry and technology as well as some methods of...
-
Finite Element Method Applied in Electromagnetic NDTE: - A Review
PublicationThe paper contains an original comprehensive review of finite element analysis (FEA) applied by researchers to calibrate and improve existing and developing electromagnetic non-destructive testing and evaluation techniques, including but not limited to magnetic flux leakage (MFL), eddy current testing, electromagnetic-acoustic transducers (EMATs). Premium is put on the detection and modelling of magnetic field, as the vast majority...
-
Centrifugal magnetic fluid seals
PublicationSeals perform an important and at times overlooked function in a lubricant system. They prevent or minimize the movement of the lubricant between two surfaces and also minimize the level of contamination in the system. Seals are divided into static and dynamic types. Static seals operate in systems where the mating surfaces do not move relative to each other. In contrast, dynamic seals operate under conditions where the mating surfaces...
-
The dependence of linear viscoelasticity limits of cold-recycled mixtures on time of curing and compaction method
PublicationCold-recycled mixtures are currently among the most widely used and investigated methods that enable recycling of old pavement structures in an environmentally friendly manner. Upon milling, the old pavement structure – whose gradation can be improved with addition of virgin aggregate – is mixed and compacted at ambient temperature. The main binding agents are bituminous emulsion and cement. Due to their dual binding behaviour,...
-
Obtaining a Well-Trained Artificial Intelligence Algorithm from Cross-Validation in Endoscopy
PublicationThe article shortly discusses endoscopic video analysis problems and artificial intelligence algorithms supporting it. The most common method of efficiency testing of these algorithms is to perform intensive cross-validation. This allows for accurately evaluate their performance of generalization. One of the main problems of this procedure is that there is no simple and universal way of obtaining a specific instance of a well-trained...
-
A Taxonomy of Model-Based Testing for Embedded Systems from Multiple Industry Domains
PublicationThis chapter provides a taxonomy of Model-Based Testing (MBT) based on the approaches that are presented throughout this book as well as in the related literature. The techniques for testing are categorized using a number of dimensions to familiarize the reader with the terminology used throughout the chapters that follow. In this chapter, after a brief introduction, a general definition of MBT and related work on available MBT...
-
Fuzzy Sets in the GIS Environment in the Location of Objects on the Surface of Water Bodies
PublicationThe issue presented here focuses on concerns about the localization of the object on water surface. The article shows how to facilitate localization process by applying mathematical solutions characterized by simplicity, rapid action and delivering credible results. The paper shows the results of background experiments, which enabled to collect technical parameters needed for conducting simulation testing. The research has been...
-
Acoustic evaluation of road surfaces using different Close Proximity testing devices
PublicationAccording to the valid standard, Close Proximity (CPX) method intends to evaluate the influence of road surfaces on traffic noise. Measurements may be carried out with the use of a self-powered vehicle or a special test trailer equipped with testing tyre towed by another vehicle. Two different testing devices took part in the research organized in Poland in order to determine the ranking of road surfaces in terms of acoustic parameters....
-
Testing for conformance of parallel programming pattern languages
PublicationThis paper reports on the project being run by TUG and IMAG, aimed at reducing the volume of tests required to exercise parallel programming language compilers and libraries. The idea is to use the ISO STEP standard scheme for conformance testing of software products. A detailed example illustrating the ongoing work is presented.
-
Determination of energy-transfer distributions in ionizing ion-molecule collisions
PublicationThe main objective of this study is to determine the energy transfer occuring in ion-molecule collisions. In order to solve this problem, we followed two approaches; the first one by validating a purely experimental method and the second one by testing a new theoretical model M3C (Microcanonical Metropolis Monte Carlo).
-
Testbed for development and verification of hybrid localization systems
PublicationIn this paper a testbed for development and verification of hybrid localization systems is presented. It allows for systematic analysis of hybrid localization methods and speed up the development of new schemes. The proposed testbed platform is composed of subsystem for sequential data collection and testing infrastructure that can be used for investigating the localization mechanisms in controllable environment.
-
Numerical and experimental study on effect of boundary conditions during testing of stiffened plates subjected to compressive loads
PublicationThis study analyses the effect of boundary conditions during testing on the structural behaviour stiffened plates with different thicknesses subjected to compressive loads. The goal of the compressive tests is to analyse the ultimate strength of a stiffened plate. During the test, relevant physical quantities are measured and investigated. The supporting structure's behaviour is investigated by analysing the force-displacements...
-
Laser Dissimilar Welding of AISI 430F and AISI 304 Stainless Steels
PublicationA dissimilar autogenous laser welded joint of AISI 430F (X12CrMoS17) martensitic stainless steel and AISI 304 (X5CrNi18-10) austenitic stainless steel was manufactured. The welded joint was examined by non-destructive visual testing and destructive testing by macro- and microscopic examination and hardness measurements. With reference to the ISO 13919-1 standard the welded joint was characterized by C level, due to the gas pores...
-
Thermal Imaging Aided Assessment of a State of Equipment Under Test and its Protecting Elements
PublicationIn the paper the investigation results using thermal imaging methods are presented. The examined is a state of equipment under test and its protecting components. The estimations are done for the chosen protecting elements during surge immunity testing. The results show that the thermal imaging methods are useful for early detection of possible damage of a device being tested
-
CRVG - a new model for wireless networks topology generation
PublicationThis paper presents a new model of wireless network topology generator. Its main advantage is the possibility of relatively sparse networks generation. Because no iteration is needed, the model can be used for massive generation of networks for testing. The topological properties of produced graphs place them in the class of scale free networks, resembling real ones.
-
Impedance Spectra of RC Model as a Result of Testing Pulse Excitation Measurement Method Dataset
PublicationThe dataset titled Impedance spectra of RC model as a result of testing pulse excitation measurement method contains the impedance spectrum of an exemplary test RC model obtained using pulse excitation. The dataset allows presentation of the accuracy of the impedance spectroscopy measuring instrument, which uses the pulse excitation method to shorten the time of the whole spectrum acquisition.
-
The effectivness of fault detection in common rail injectors examination methods
PublicationThe article presents the effectiveness tests of fault detection in common rail injectors. 40 injectors with different wear levels were tested. Testing was made on two test benches of a completely different design. Research includes comparison of accuracy, reproducibility and testability to detect specific defects. A device was created for visualization of the fuel injector spraying steam.
-
A new method for measuring the psychoacoustical properties of tinnitus
Publicationinformation, select the tinnitus treatment and quantitatively substantiate its effects, the measurement of the Tinnitus psychoacoustic parameters should be made an inherent part of the Tinnitus therapy. Methods For this purpose the multimedia-based sound synthesizer has been proposed for testing tinnitus and the results obtained this way are compared with the outcome of the audiometer-based Wilcoxon test. The method has been verified...
-
Tensile and Fatigue Behavior of Additive Manufactured Polylactide
PublicationThis article presents the results of monotonic tensile and fatigue tests conducted on commercial polylactide or polylactic acid (PLA). The results of fatigue tests for this material present in the literature are limited, especially for additive manufactured elements. The specimens were manufactured using the injection molding and the fused filament fabrication (FFF) method. The FFF specimens were divided into five subgroups, depending...
-
An idea of an approach to self-testing of mixed signal systems based on a quadratic function stimulation
PublicationA new approach to self-testing of the analog parts of mixed-signal electronic systems controlled by microcontrollers equipped with an ADC and a DAC is presented. It is based on a BIST and a new fault diagnosis method. A novelty is the use of the DAC as a component of the BIST, allowing to generate a stimulating signal with a quadratic function shape. It contributes to a better extraction of information about the state of the circuit...
-
Immunity of residual current devices to the impulse leakage current in circuits with variable speed drives
PublicationThis paper concerns reliability of supply in variable speed drive circuits with residual current devices. During normal operation of these circuits high value of leakage current causes unwanted tripping of residual current devices. Immunity of residual current devices to the impulse leakage current should be evaluated. The system for testing of residual current devices and results of the test are presented
-
Usability Techniques Possible to Use in Diagnostic Tools Interface Improvement
PublicationThe development of diagnostic tools has caused a rapid increase in the amount of information generated and presented, necessitating the use of computer displays as an interface to data presentation and the use of modern diagnostic tools. The paper presents methods for testing usability that can be used in designing and improving the quality of interfaces of modern diagnostic tools that use communication through graphical user interfaces.
-
Low-power device simulator for micro-energy measurement methods testing
PublicationThe paper presents low-power device simulator designed for testing of micro-energy measurement methods. Such kind methods can be used for evaluation of power systems based on Energy Harvesting. The device allows to set the current consumption characteristic over the time, thus making possible playing the role of different types of low-power devices e.g. simulating sensor network node.