Filters
total: 650
filtered: 528
-
Catalog
Chosen catalog filters
Search results for: ansys motor CAD
-
Sensorless Multiscalar Control of Five-Phase Induction Machine with Inverter Output Filter
PublicationThe paper presents a complete solution for speed sensorless control system for five-phase induction motor with voltage inverter, LC filter and nonlinear control of combined fundamental and third harmonic flux distribution. The control principle, also known as multiscalar control, nonlinear control or natural variables control, is based on a use of properly selected scalar variables in control feedback to linearize controlled system....
-
Quasi-discrete modelling of PMSM phase currents in drives with low switching-to-fundamental frequency ratio
PublicationThis study proposes a new quasi-discrete approach to modelling the permanent magnet synchronous motor (PMSM). The quasi-discrete modelling reflects the impact of continuous rotor movement, which takes place during a control cycle, on the shape of motor current waveforms. This provides much improvement in current modelling accuracy under inverter low switching-to-fundamental frequency operation. The proposed approach may be used...
-
Analiza porównawcza 2D i 3D klasycznego i bezstykowego elektrycznego ogrzewania rozjazdów kolejowych
PublicationElektryczne ogrzewanie rozjazdów jest istotnym problemem technicznym i ekonomicznym. Z tych względów istnieje potrzeba prowadzenia badań w celu optymalizacji systemu ogrzewania rozjazdów kolejowych. W niniejszym artykule przedstawiono wyniki analizy numerycznej układów ogrzewania rozjazdów kolejowych metodą klasyczną oraz z zastosowaniem grzejników odizolowanych termicznie od stopki szyny. Przeprowadzono analizę 2D i 3D rozpatrywanych...
-
Novel Nonlinear High Order Technologies for Damage Diagnosis of Complex Assets
PublicationFor the first time worldwide, innovative techniques, generic non-linear higher-order unnormalized cross-correlations of spectral moduli, for the diagnosis of complex assets, are proposed. The normalization of the proposed techniques is based on the absolute central moments, that have been proposed and widely investigated in mathematical works. The existing higher-order, crosscovariances of complex spectral components are not sufficiently...
-
The adaptive backstepping control of PMSM supplied by current source inverter for the field weakening region
PublicationThe sensorless control system of permanent magnet synchronous motor PMSM supplied by current source inverter for field weakening operation is presented in this paper. The adaptive backstepping control system and the backstepping speed observer are presented. The control system is based on multi-scalar variables. The control variables are: dc-link voltage and the output current vector pulsation. The control system was named voltage...
-
Wielkie wydarzenia jako katalizator procesów rewitalizacji
PublicationCelem referatu jest naświetlenie procesów rewitalizacji towarzyszących organizacji wielkich wydarzeń w dwóch aspektach: 1) rewitalizacja jako motor lub jako skutek działań; 2) lokalność i regionalność procesów rewitalizacji. Omówieniu tych zjawisk służą przykłady miast-organizatorów wielkich wydarzeń, Sydney (IO 2000), Pekin (IO 2008), Londyn (IO 2012) oraz Gdańsk (Euro 2012) i Szczecin (The Tall Ships Races 2013). Kluczową kwestią...
-
Sensorless IPMSM drive with rotor position estimator based on analysis of phase current derivatives
PublicationThis paper describes a sensorless Interior Permanent Magnet Synchronous Motor (IPMSM) drive designed for traction applications. Wide-speed sensorless operation is provided with the use of three methods of rotor position estimation designed for: a standstill, low- and high-speed range. The paper focuses on the high-speed estimation algorithm. The estimator uses the derivatives of motor phase currentsresulting from PWM modulation...
-
Optymalizacja transformacji wyników pomiarów bloków kadłuba statku z uwzględnieniem ograniczeń
PublicationArtykuł przedstawia algorytm optymalizujący transformację wyników pomiarów bloków i sekcji kadłuba statku z uwzględnieniem ograniczeń. Optymalizacji podlega suma odległości pomiędzy mierzonymi punktami, a korespondującymi punktami w modelu CAD, uwzględniając jedno z dwóch możliwych ograniczeń: wspólna płaszczyzna, albo wspólna oś. Transformacja wyników pomiarów wykonywana jest wcelu przeprowadzenia porównania faktycznych wymiarów...
-
Metodyka projektowania łożysk ślizgowych z tamą hydrodynamiczną.
PublicationW artykule przedstawiono nową metodykę projektowania poprzecznych łożysk ślizgowych z tamą hydrodynamiczną. Zaproponowana metoda pozwala na wyznaczanie charakterystyk statycznych i dynamicznych dowolnych łożysk poprzecznych, w których wykonano jedną lub wiele tam hydrodynamicznych. W omawianej metodzie wykorzystano dwa niezależne programy komputerowe (BEARing i ArtBEAR). W celu oszacowania dokładności wybranej metody wykonano obliczenia...
-
Search for optimum geometry of selected steel sandwich panel joints
PublicationZastosowanie stalowych paneli typu sandwich w konstrukcjach okrętowych wymaga rozwiązania wielu problemów. Jednymi z trudniejszych zagadnień związanych z tymi nowymi strukturami są połączenia pomiędzy panelami oraz między panelami i konstrukcją innego typu. Artykuł przedstawia poszukiwanie optymalnej geometrii połączenia typu panel-panel w układzie wzdłużnym, przy użyciu parametrycznego modelu w programie ANSYS. Poszukiwano konfiguracji...
-
Komputerowa analiza węzła kompensacji luzów nowego typu silników satelitowych
Publicationopisano analizę komputerową z wykorzystaniem metody mes nowego typu silników satelitowych o małych objętościach roboczych. silniki te przeznaczone są między innymi do napędów narzędzi górniczych. celem prowadzenia tych analiz była poprawa węzła kompensacji luzów osiowych. analizy wykonane były w oparciu o metodę elementów skończonych i przygotowane przy wykorzystaniu programu ansys. dodatkowo przeprowadzono eksperymentalną weryfikację...
-
Path integrals formulations leading to propagator evaluation for coupled linear physics in large geometric models
PublicationReformulating linear physics using second kind Fredholm equations is very standard practice. One of the straightforward consequences is that the resulting integrals can be expanded (when the Neumann expansion converges) and probabilized, leading to path statistics and Monte Carlo estimations. An essential feature of these algorithms is that they also allow to estimate propagators for all types of sources, including initial conditions....
-
Polish Regions in Implementation of the Lisbon Strategy
PublicationPolskie regiony w gospodarce opartej na wiedzy. Innowacje jako motor rozwoju regionalnego. Rola regionalnych strategii innowacji (RIS). Fundamentem RIS są technologie innowacyjne i kompleksy naukowo-badawcze. Warunkiem jest rozwój społeczeństwa wiedzy.
-
Metodyka badań rozwojowych nowego typu silników i pomp satelitowych
PublicationResearch and development of new type satellite motors and satellite pumps SM with small geometrical displacement, from 5 to 73 cm3/rev, has been conducted in cooperation with Stosowanie Maszyn company from Katowice (manufacturer of motors and pump SM). The improvement of construction of those machines, especially construction of axial compensation and construction of fluid distribution channels have been the main problem of research...
-
Pathological and physiological high-frequency oscillations in focal human epilepsy
PublicationHigh-frequency oscillations (HFO; gamma: 40-100 Hz, ripples: 100-200 Hz, and fast ripples: 250-500 Hz) have been widely studied in health and disease. These phenomena may serve as biomarkers for epileptic brain; however, a means of differentiating between pathological and normal physiological HFO is essential. We categorized task-induced physiological HFO during periods of HFO induced by a visual or motor task by measuring frequency,...
-
Molecular mechanism and energetics of coupling between substrate binding and product release in the F 1 -ATPase catalytic cycle
PublicationF1-ATPase is a motor protein that couples the rotation of its rotary γ subunit with ATP synthesis or hydrolysis. Single-molecule experiments indicate that nucleotide binding and release events occur almost simultaneously during the synthesis cycle, allowing the energy gain due to spontaneous binding of ADP to one catalytic β subunit to be directly harnessed for driving the release of ATP from another rather than being dissipated...
-
High Performance Control of AC Drives with Matlab/ Simulink
PublicationExplore this indispensable update to a popular graduate text on electric drive techniques and the latest converters used in industry. The Second Edition of High Performance Control of AC Drives with Matlab®/Simulink delivers an updated and thorough overview of topics central to the understanding of AC motor drive systems. The book includes new material on medium voltage drives, covering state-of-the-art technologies and challenges...
-
3D Printing of Metallic Implants
PublicationThe fabrication of various elements, solid and open porous structures of stainless steel and Ti alloy is described. The process was started with the design of 3D models in CAD/CAM system. The 3D models were transformed into *.stl files and then the manufacturing process of the real structures by means of the selective laser melting with the SLM Realizer 100 3D printer was made. The paper shows the porous specimens made for possible...
-
IDENTIFICATION OF THE INTERFECE OF LATERAL SLIDE BEARINGS
PublicationIn the paper, the model of slide bearings of motor engine, the metodology of research on this type of bearings and its results are presented measurement standpoint consisting of main elements of Briggs & Stratton 550 serie 10 T 802 model piston motor engine driven by three phase elektric engine is introduced . On the measurement standpoint are measurements were done, needed for specification...
-
Impact of Low Switching-to-Fundamental Frequency Ratio on Predictive Current Control of PMSM: A simulation study
PublicationPredictive current control algorithms for permanent magnet synchronous (PMSM) drives rely on an assumption that within short intervals motor currents can be approximated with linear functions. This approximation may result either from discretizing the motor model or from simplifications applied to the continuous-time model. As the linear current approximation has been recognized as inaccurate in case when the drive operates with...
-
Analytical modeling of electric drives for vehicle traction control systems
PublicationWheel-torque control bandwidth in vehicle dynamics model is crucial in evaluating optimal tracking ability of tire slip and in analysis of control system stability. Electric drives’ control dynamics are influenced by timing of digital control events, e.g. by sampling instant of motor currents. Reflecting this timing in drive analytical models is therefore important for analysis of vehicle traction systems. The paper considers five...
-
Współczynniki strat energetycznych w elementach napędu hydrostatycznego
PublicationW każdym układzie napędowym należy zastąpić obraz przepływu mocy opisany dotychczas powszechnie stosowanym wykresem Sankey’a spadku mocy zgodnego z kierunkiem przepływu mocy proponowanym przez autora wykresem wzrostu mocy w układzie przeciwnego do kierunku przepływu mocy. Należy więc opisywać straty i sprawność energetyczną a także pole pracy każdego silnika i układu napędowego jako zależne od wielkości fizycznych niezależnych...
-
Analiza rozkładu pola magnetycznego w kadłubie okrętu z cewkami układu demagnetyzacyjnego
PublicationOkręty wyposażone są w system automatycznej demagnetyzacji. W zależności od kursu okrętu prądy płynące w cewkach umieszczonych wewnątrz okrętu minimalizują pole własne okrętu. Uzwojenia demagnetyzacyjne powinny być tak rozmieszczone, aby zapewniały w przybliżeniu równomierny rozkład pola magnetycznego w kadłubie okrętu. Z tego względu konieczne jest określenie odpowiedniego rozkładu przestrzennego uzwojeń demagnetyzacyjnych okrętu....
-
Komputerowy model 3D stawu biodrowego
PublicationW pracy przedstawiono stworzony w programie ANSYS komputerowy model 3D stawu biodrowego. Model wykonano w oparciu o budowę anatomiczną oraz zebrane dane dotyczące stałych materiałowych kości i elementów chrzęstnych. Analiza i porównanie modelu biochemicznego, lepkosprężystego, mieszanego oraz molekularno – agregacyjnego służy ułatwieniu stworzenia modelu najbliższego rzeczywistości, który można by wykorzystać w projektowaniu endoprotez...
-
Hałaśliwość silników asynchronicznych – podstawy nowych hipotez
PublicationArtykuł zawiera nowe spojrzenie na hałas emitowany przez silniki asynchroniczne. Poprzez wykonane badania akustyczne z analizami widmowymi określono związki przyczynowo-skutkowe powstawania drgań i hałasu przy zasilaniu sieciowymch i przekształtnikowym. Na podstawie wyznaczonych charakterystyk kierunkowych ciśnienia akustycznego silników sformułowano hipotezę, że rola tarcz łożyskowych w emitowaniu hałasu przez silnik może być...
-
Neutral point balancing technique for 3-level neutral point clamped converter with servo system
PublicationNeutral point voltage drift compensation technique in 3-level NPC multilevel converter and servo system is described in the paper. Analytical expressions are obtained for power subsystem elements parameters of servo drive system. Simulation of servo system, based on PMSM motor with 3-level NPC converter is considered.
-
Impact of digital signal processing on FOC current feedback in high-speed PMSM drive
PublicationIn applications where size and weight of the electric motor are among major design concerns, Permanent Magnet Synchronous Motors (PMSMs) with wide operational speed-range are commonly preferred. Due to limited inverter switching frequency, high-speed operation of a drive results in a low ratio between the switching frequency and the fundamental frequency of motor voltage. Such operating conditions have been recently identified...
-
CFD analysis of fluid flow through the labyrinth seal
PublicationSteam and gas turbines are some of the fundamental means of power generation. The energy efficiency of the turbines, however, is not satisfactory. Ever since the start-up of the first turbine in the world, engineers have been striving for their increased efficiency. Multiple solutions to the problem of steam loss in an operating turbine are available. The use of seals is one of them. Empirical methods or numerical calculations...
-
Comparative Analysis of Numerical and Experimental Studies of the Airflow Around the Sample of Urban Development
PublicationIn this paper, on the background of a short overview of the recent advances in the field of Environmental Wind Engineering (EWE), a comparison of wind tunnel experiment and numerical simulation for some cases of airflow around an urban layout have been reported. The purpose of the study is quantitative and qualitative comparison of measurements in the wind tunnel as well as numerical simulation using Ansys Fluent software. The...
-
COOPERATION BETWEEN UNIVERSITY AND EXTERNAL COMPANY IN ARCHITECTURAL INVENTORY USING INNOVATIVE MEASURING TECHNOLOGY
PublicationArchitectural inventories are the main field for using innovative technology ( remote sensing). The main purpose of using ie. Laser scanning or photogrammetry is to capture all of the important details of structure. Regarding the extents of inventory works, it may only apply to external details, such as facades, supporting structures and surroundings, whilst in terms of advanced inventory, the building's interior is also expected...
-
A pilot study to assess an in-process inspection method for small diameter holes produced by Direct Metal Laser Sintering
PublicationPurpose The purpose of this research is to evaluate the geometric quality of small diameter holes in parts printed by DMLS technology. An in-process optical inspection method is proposed and assessed during a pilot study. The influence of the theoretical hole diameter assumed in a CAD system and the sample thickness (hole length) on the hole clearance was analysed. Design/methodology/approach The samples made of two different...
-
Variable Speed AC Drives with Inverter Output Filters
PublicationThe advance of variable speed drives systems (VSDs) engineering highlights the need of specific technical guidance provision by electrical machines and drives manufacturers, so that such applications can be properly designed to present advantages in terms of both energy efficiency and expenditure. This book presents problems and solutions related to inverter-fed electrical motors. Practically orientated, the book describes the...
-
Appendix E
PublicationThe advance of variable speed drives systems (VSDs) engineering highlights the need of specific technical guidance provision by electrical machines and drives manufacturers, so that such applications can be properly designed to present advantages in terms of both energy efficiency and expenditure. This book presents problems and solutions related to inverter-fed electrical motors. Practically orientated, the book describes the...
-
Prosthetic Elements Made of the Ti-13Zr-13Nb Alloy by Selective Laser Melting
PublicationThe fabrication of the prosthetic foundations and bridges from the Ti-13Zr-13Nb alloy is described. The process was started from CAD/CAM design of 3D models of the foundations based on scanning of patient`s mouth. Next, 3D models were transformed into *.stl files for the manufacturing stage and then the manufacturing process by means of the selective laser melting with the SLM Realizer 100 equipment was made. The intrinsic structure...
-
Computer-aided analysis of thermal convection near electric devices
PublicationObciążalność długotrwała urządzeń elektrycznych zależy od intensywności oddawania ciepła przez te urządzenia do otoczenia. Dla zwiększenia obciążalności długotrwałej urządzeń stosuje się konwekcję wymuszoną np. z wykorzystaniem wentylatorów. Wszechstronne obserwacje i analiza procesów konwekcji naturalnej wskazują, że jej intensyfikację można uzyskać dzięki umieszczaniu w pobliżu urządzenia oddającego ciepło elementów tworzących...
-
Koncepcja i modelowanie silnika o wirującym tworniku oraz magneśnicy do zastosowania w napędzie miejskiego samochodu elektrycznego
PublicationW artykule zaprezentowano koncepcję, model oraz prototyp silnika z wirującym twornikiem oraz magneśnicą. Opisano historię powstania i zastosowania tego typu silników w motoryzacji. Przedstawiono nowoczesne rozwiązania konstrukcyjne i zastosowania we współczesnych samochodach elektrycznych i hybrydowych. Opracowano model silnika z wirującym twornikiem i magneśnicą oraz przedstawiono wybrane wyniki symulacji przeprowadzone w programie...
-
Koncepcja, realizacja i analiza nowego typu silnika piezoelektrycznego o strukturze wielokomórkowej
PublicationDotychczasowe wyniki badań w obszarze aktuatorów piezoelektrycznych, wskazują ich potencjalnie duże możliwości w przyszłych zastosowaniach specjalnych. W artykule przedstawiono proces projektowania nowego typu silnika piezoelektrycznego. Opisane zostały wybrane topologie maszyn piezoelektrycznych. Przedstawiono wady i zalety silnika ultrasonicznego z falą biegnącą oraz silnika o ruchu obrotowym. W ramach realizacji projektu...
-
Przekształtnik prądu jako sterownik w układach napędowych z silnikami indukcyjnymi
PublicationThe circuits used for power conversion applied in drives with electric machines are classified into two groups: voltage source inverters (VSI) and current source inverters (CSI). Application of the current source inverter results in better properties of drive than application of voltage source inverter because there is no output filter. The development of power electronics and especially the IGBTs, in which on/off-times are very...
-
Bezczujnikowe sterowanie trakcyjnym silnikiem IPMSM małej mocy
PublicationThis paper describes an algorithm for estimation of IPMSM angular rotor position. The algorithm uses derivatives of motor phase currents resulting from PWM modulation to obtain the rotor position. Control of the IPMSM electromagnetic torque requires a precise estimation of the rotor angular position throughout the wide speed range. This involves using a set of estimation methods switched with the dependence on the actual rotor...
-
Możliwości poprawy sprawności pomp głębinowych HYDRO-VACUUM SA drogą zastosowania nowoczesnych komputerowych metod projektowania
PublicationW prezentacji omówiono algorytm postępowania jaki został zrealizowany przy modernizacji istniejącej konstrukcji pompy głębinowej. Modernizacji dokonano przy użyciu nowoczesnych metod komputerowych z wykorzystaniem własnego oprogramowania do obliczeń jedno i dwu-wymiarowych oraz komercyjnych programów CAD i do obliczeń przepływów 3D (Fluent). Porównano wyniki badań na konstrukcji rzeczywistej z badaniami numerycznymi konstrukcji...
-
Inteligentny modeler graficzny w komputerowych systemach wspomagania projektowania budowlanego
PublicationW pracy przedstawiono Inteligentny Modeler Graficzny (IMG), integrujący proces projektowania w systemach CAD. IMG integruje dwie podstawowe fazy projektowania : fazę konstruowania z fazą analziy konstrukcji. Podstawą integracji stałą się metoda Graphic Data Edition (GDE) rozpoznawania rysunku, oprata na koncepcji Logiki Rozmytej. Metoda GDE pozwoliła na zbudowanie modelera rozmytego, mającego za zadanie rozpoznanie rysunku i wygenerowanie...
-
Koncept ekologicznie przyjaznego masowca „Gary Muwalt” napędzanego siłą wiatru
PublicationW artykule przeanalizowano możliwości, jakie niesie wykorzystanie siły wiatru we współczesnym transporcie morskim na przykładzie ekologicznego masowca z napędem żaglowym. W tym celu dokonano analiz oporowych przy użyciu metod CFD oraz analizy ekonomicznej na podstawie danych rynkowych. Jest to wstęp do dalszych prac, mających na celu stworzenie nowoczesnej jednostki ograniczającej emisję szkodliwych substancji do atmosfery oraz...
-
Zastosowanie AutoCAD Civil3D w nauczaniu projektowania dróg szynowych
PublicationNa Wydziale Inźynierii Lądowej i Środowiska Politechniki Gdańskiej od kilku lat głównym programem typu CAD wykorzystywanym w procesie kształcenia jest AutoCAD Civil 3D. Wersja edukacyjna tego programu jest zainstalowana w uczelnianych laboratoriach komputerowych, a studenci i pracownicy uczelni mogą go instalować na swoich komputerach w ramach programu Autodesk Student Engineering & Design Community. Jednak sposób rozwiązywania...
-
Ocena wpływu wymiarów wypełnienia kontrolowanego i rezystywności cieplnej ziemi rodzimej na obciążalność długotrwałą kabli elektroenergetycznych
PublicationRezystywność cieplna ziemi ma istotny wpływ na obciążalność prądową długotrwałą elektroenergetycznych linii kablowych. W przypadku niekorzystnej rezystywności cieplnej można zastosować wypełnienie kontrolowane, czyli wymianę ziemi wokół kabli na substancję o znanych parametrach cieplnych. Wyznaczenie obciążalności długotrwałej z wypełnieniem kontrolowanym jest kłopotliwe, ponieważ na jej wartość wpływ ma zarówno rezystywność cieplna,...
-
Aplikacje i środowiska kontekstowe: Ontologie w interaktywnych aplikacjach zorientowanych kontekstowo
PublicationPrzedstawiono model przetwarzania typu pervasive computing. Zanalizowano składowe aplikacji interaktywnej zorientowanej kontekstowo. Opisano architekturę takiej aplikacji, wykorzystującej usługi sieciowe, konteksty, scenariusze i ontologie. Scharakteryzowano metodę integracji tych elementów w wykorzystaniem adnotacji. zaproponowano motor wykonawczy dla kontenera usług sieciowych, bazujący na standardach: OSGi OWL-S
-
Compact satellite hydraulic unit
PublicationThe article describes the design and operation of a prototype hydraulic unit. It is based on an inversed kinematics, satellite pump in which the body rotates around the shaft. The pump is placed inside the electric motor. Thanks to that the compact and low mass construction was achieved. Thanks to new commutation unit with enlarged channels, lower pressure losses were obtained. The article presents the construction and results...
-
Current Source Inverter Fed Drive
PublicationThis book covers three-phase and multiphase (more than three-phase) motor drives including their control and practical problems faced in the field (e.g., adding LC filters in the output of a feeding converter), are considered. The new edition contains links to Matlab®/Simulink models and PowerPoint slides ideal for teaching and understanding the material contained within the book. Readers will also benefit from the inclusion of: A...
-
TeleCAD w kształceniu studentów Wydziału Inżynierii Lądowej Politechniki Gdańskiej
PublicationPrzedstawiono system TeleCAD opracowany w ramach projektu Leonardo da Vinci - Teleworkers Training for CAD Systems Users (1998-2001). Głównym celem projektu było stworzenie środowiska obsługi kursów programu AutoCAD bazującego na Internecie jako medium do komunikacji między uczestnikami oraz do dostarczania materiałów kursowych. W artykule zaprezentowano również system służący do oceny jakości szkoleń na odległość. Szkolenie TeleCAD...
-
Micromouse robot - technical design and construction
PublicationW ostatnich latach obserwuje się intensywny rozwój robotyki. Roboty znajdują zastosowanie w różnych gałęziach przemysłu i życiu codziennym. Ich projektowanie wymaga interdyscyplinarnej wiedzy obejmującej obszary mechaniki, elektroniki, metrologii, automatyki i informatyki. W artykule przedstawiono poszczególne etapy wykonania robota typu Micromouse. Jest to specyficzne urządzenie, którego zadaniem jest zbadanie labiryntu, dotarcie...
-
Zastosowanie obserwatora ATO do filtracji wyników estymacji położenia w napędzie z silnikiem PMSM
Publicationreferacie zaproponowano zastosowanie obserwatora ATO (ang. Angle Tracking Observer) do poprawy dokładności odtwarzania położenia kątowego wirnika silnika PMSM (ang. Permanent Magnet Synchronous Motor) za pomocą estymatora fizykalnego. Opracowano dedykowaną, uproszczoną strukturę ATO. Zaproponowano procedurę doboru nastaw wzmocnień obserwatora w oparciu o model symulacyjny. Skuteczność działania ATO potwierdzono badaniami eksperymentalnymi.