Filters
total: 3530
filtered: 2878
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: INTERNAL CARBON SOURCE
-
CPTU/DMT control of heavy tamping compaction of sands
PublicationHeavy tamping compaction method in cohesionless alluvial soil was evaluated with CPTU and DMT tests. Some examples of interpretation of soundings in pre-treated and compacted sands are given. The compaction work was performed in two stages. Compaction control was performed after each stage of tamping. Additional tests were performed two weeks after the compaction works completion to study the set-up effect. While typical increase...
-
Dissociative ionization dynamics of dielectric gas C3F7CN
PublicationFluoronitrile C3F7CN is a promising candidate for the replacement of SF6 dielectric gas in high-voltage insulation. We present a combined experimental and theoretical study on its ionization dynamics probed in the 0-100 eV energy range. We exploited the total ion collection technique to determine the absolute ionization cross section, mass spectrometry to determine the fragment branching ratios and ab initio nonadiabatic molecular...
-
Analysis of the regenerative braking process for the urban traffic conditions
PublicationIn a regular drive system, with an internal combustion engine, vehicle braking is connected with the unproductive dissipation of kinetic and potential energy accumulated in the mass of the vehicle into the environment. This energy can constitute up to 70% of the energy used to drive a vehicle under urban conditions. Its recovery and reuse is one of the basic advantages of hybrid and electric vehicles. Modern traffic management...
-
The effect of pre-hydrogen charging on corrosion behaviour of superduplex stainless steel welded joints
PublicationThe paper presents results of research undertaken to determine the influence of hydrogen on passivity and corrosion resistance of 2507 super duplex stainless steel welded joints. Butt welded joints were made with low heat input using flux corded arc welding (FCAW) method. Coupons of 5.0 x 5.0 mm were cut from the welded joints containing weld metal (WM), heat affected zone (HAZ) and parent metal (PM). Hydrogen was introduced...
-
Multi-mode vibronic interactions in the five lowest electronic states of the fluorobenzene radical cation
PublicationThe multi-mode vibronic interactions between the five lowest electronic states of the fluorobenzene radical cation are investigated theoretically, based on ab initio electronic structure data, and employing the linear vibronic coupling model. Low-energy conical intersections, and strong vibronic couplings are found to prevail within the set of X-A and B-C-D cationic states, while the interactions between these two sets of states...
-
Time-domain measurement methods for R, L and C sensors based on aversatile direct sensor-to-microcontroller interface circuit
PublicationtIn the paper new time-domain measurement methods for determining values of resistive (R), inductive(L) and capacitive (C) sensors based on a versatile direct sensor-to-microcontroller interface for microcon-trollers with internal analog-to-digital converters (ADCs) and analog comparators (ACs) are presented.The interface circuit consists of a reference resistor Rrworking as a voltage divider, a given R, L or C sensorand a microcontroller...
-
MARSTRUCT benchmark study on nonlinear FE simulation of an experiment of an indenter impact with a ship side-shell structure
PublicationThis paper presents a benchmark study on collision simulations that was initiated by the MARSTRUCT Virtual Institute. The objective was to compare assumptions, finite element models, modelling techniques and experiences between established researchers within the field. Fifteen research groups world-wide participated in the study. An experiment involving a rigid indenter penetrating a ship-like side structure was used as the case...
-
Characterization of volatile compounds, structural, thermal and physico-mechanical properties of cross-linked polyethylene foams degraded thermo-mechanically at variable times
PublicationWaste cross-linked polyethylene foam (wXLPE) was thermo-mechanically degraded at variable time using internal batch mixer. The progress of wXLPE degradation has been investigated by using a simultaneous thermogravimetric/differential scanning calorimetry analyzer coupled with Fourier transform infrared spectroscopy, swelling measurements, tensile tests and scanning electron microscopy. Volatile organic compounds generated during...
-
Chinese Foreign Direct Investments in Europe. The Polish Case
PublicationThe first aim of this paper is to analyze the features that have motivated Chinese outbound investments in the European Union. The paper outlines also the policies adopted by the European institutions and its member states to encourage the increase of the Chinese FDI without harming the internal European market, and consequently phase out all concerns that are afflicting the European public opinion. The second purpose is more focused...
-
Distributed Framework for Visual Event Detection in Parking Lot Area
PublicationThe paper presents the framework for automatic detection of various events occurring in a parking lot basing on multiple camera video analysis. The framework is massively distributed, both in the logical and physical sense. It consists of several entities called node stations that use XMPP protocol for internal communication and SRTP protocol with Jingle extension for video streaming. Recognized events include detecting parking...
-
Micro-modelling of shear localization during quasi-static confined granular flow in silos using DEM
PublicationThe paper deals with the quasi-static confined flow of cohesionless sand in a plane strain model silo with parallel walls and a slowly movable bottom. Numerical modelling was carried out by the discrete element method (DEM) using spheres with contact moments to approximately capture a non-uniform shape of sand particles. Different initial void ratios of sand and silo wall roughness grades were employed. Regular triangular grooves...
-
On the lack of explicit internal criticism of contemporary personalists. An outline of the problem
Publication -
Optimization of the geometry of the crankshaft for an internal combustion engine with heat regeneration
Publication -
Role of Dean’s Offices in Developing Internal Normative Acts at HEIs
Publication -
TEST FOR ASSESSING THE ENERGY EFFICIENCY OF VEHICLES WITH INTERNAL COMBUSTION ENGINES
PublicationThe most popular method for assessing the energy efficiency of vehicles is to compare the fuel consumption achieved in the conditions of selected approval test. Operating conditions are defined using the speed profiles, usually for only two categories: urban and extra-urban driving. Assessing the energy efficiency of vehicles should be performed using a more detailed classification of conditions. Presented results of comparison...
-
Construction of glucosamine-6-phosphate synthase with an internal hexahistydyl fragment
PublicationL-Glutamine: D-fructose-6-phosphate aminotransferase (EC 2.6.1.16), known also as glucosamine-6-phosphate (GlcN-6-P) syntase, catalyzes the first committed step in the amino sugar biosynthetic pathway in prokaryotic and eukaryotic organisms. The enzyme carries out a complex reaction involving ammonia transfer and sugar phosphate isomerization. GlcN-6-P syntase is an important point of metabolic control of amino sugar biosynthesis...
-
Internal friction in pure Co and CoPt alloy during ordering
PublicationZbadano tarcie wewnętrzne, wskaźnik modułu sprężystości postaciowej i podatność magnetyczną stopu CoPt (50% at. Pt) w stanie nieuporządkowanym, uzyskanym w wyniku oziębienia, podczas wyżarzania do 850 K przy wzrostach temperatury 6K/min. i 2K/min., stosując odwróconą skręcarkę wahadłową. Zaobserwowano maksimum tarcia wewnętrznego w CoPt przy 700 K oraz w monokrysztale kobaltu w 720 K w pobliżu martenzytycznej przemiany fazowej,...
-
Fixed roof to shell connection in tank with an internal floating cover.
PublicationReferat dotyczy projektowania połączenia dachu stałego zbiornika walcowego z płaszczem w przypadku zastosowania wewnętrznego przekrycia pływającego. Zaproponowano zastosowanie dodatkowego pierścienia usztywniającego, zabezpieczającego górną krawędź płaszcza zbiornika. Wyniki analiz z zastosowaniem metody elementów skończonych zamieszczono w formie map naprężeń.
-
Monosaccharides as internal probes for the determination of the absolute configuration of 2-butanol
PublicationD-dlukoza, D-mannoza i L-ramnoza zostały poddane reakcji z mieszaniną racemiczną 2-butanolu. Otrzymane w ten sposób glikozydy były analizowane za pomocą spektroskopii NMR, z wykorzystaniem eksperymentów COSY i NOESY. Analiza konformacyjna wiązania glikozydowego (dokonana w oparciu o modelowanie molekularne i heteronuklearne stałe sprzężenia) wraz z analizą sprzężeń dipolowych obserwowanych w widmie NOESY umożliwiła określenie konfiguracji...
-
Study on a polish peat bog “Rucianka” as a source of yeast strains capable of effective phenol biodegradation
PublicationPhenol is one of the most widely distributed environmental pollutants which can be found in wastewaters and industrial effluents. Due to its toxicity and resistance to self-degradation, it could become even lethal for humans and animals. The treatment of this toxic compound is focused on psychical–chemical methods, although biological treatment of phenol is preferable for economic aspects related to relatively...
-
On the plastic buckling of curved carbon nanotubes
PublicationThis research, for the first time, predicts theoretically static stability response of a curved carbon nanotube (CCNT) under an elastoplastic behavior with several boundary conditions. The CCNT is exposed to axial compressive loads. The equilibrium equations are extracted regarding the Euler–Bernoulli displacement field by means of the principle of minimizing total potential energy. The elastoplastic stress-strain is concerned...
-
Investigation of the road noise source employing an automatic noise monitoring station
PublicationThe paper presents a pilot investigation of noise source models in two selected localizations in the context of future dynamic noise map creation. The experiments were carried out using the automatic noise monitoring station engineered at the Multimedia Systems Departmentof the Gda´nsk University of Technology. The results of the noise measurements employing monitoring stations and its comparison to the reference values are depicted....
-
Comparative Evaluation of Multicoil Inductive Power Transfer Approaches Based on Z-source Network
PublicationThis paper describes comparative evaluation between wireless power transfer topologies with utilization of Z-source network. Paper describes components calculation method. List of open-loop, close-loop simulations were conducted to compare both topologies. Spectrum of signals is also researched.
-
Generation-recombination and 1/f noise in carbon nanotube networks
PublicationThe low-frequency noise is of special interest for carbon nanotubes devices, which are building blocks for a variety of sensors, including radio frequency and terahertz detectors. We studied noise in as-fabricated and aged carbon nanotube networks (CNNs) field-effect transistors. Contrary to the majority of previous publications, as-fabricated devices demonstrated the superposition of generation-recombination (GR) and 1/f noise...
-
A Novel Coupling Matrix Synthesis Technique for Generalized Chebyshev Filters With Resonant Source–Load Connection
PublicationThis paper reports a novel synthesis method for microwave bandpass filters with resonant source–load connection. In effect, a network realizing N+1 transmission zeros (where N is the number of reflection zeros) is obtained. The method is based on a prototype transversal coupling matrix (N+2, N+2) with source and load connected by a resonant circuit formed by a capacitor in parallel with a frequency-invariant susceptance. To complement...
-
Negative carbon dioxide gas power plant integrated with gasification of sewage sludge
PublicationOne of the primary objectives of the negative carbon dioxide gas power plant (nCO2PP) is to develop an innovative technology confirming the possibility of the use of sewage sludge to produce electricity while having a positive impact on the environment. In this paper, a mathematical model is presented to estimate thermodynamic parameters of the system in relation to the gasification process and changes in such parameters in the...
-
Open-transistor fault diagnostics in voltage-source inverters by analyzing the load current
PublicationA novel method is presented for the detection andisolation of open-transistor faults in voltage-source invertersfeeding low-power AC motors. The method is based onmonitoring two diagnostic signals, one indicating sustained nearzerovalues of output current and thus permitting fault detection,the other permitting the isolation of the particular transistorwhich went faulty. The latter signal is the ratio of the averagephase current...
-
Electrically Conductive Carbon‐based (Bio)‐nanomaterials for Cardiac Tissue Engineering
PublicationA proper self-regenerating capability is lacking in human cardiac tissue which along with the alarming rate of deaths associated with cardiovascular disorders makes tissue engineering critical. Novel approaches are now being investigated in order to speedily overcome the challenges in this path. Tissue engineering has been revolutionized by the advent of nanomaterials, and later by the application of carbon-based nanomaterials...
-
The Internet as a knowledge source in Knowledge Views
PublicationArtykuł ten przedstawia koncepcję widoków na bazę wiedzy, jak może ona zostać wykorzystana w celu zbierania informacji z różnych źródeł, wnioskowania nad tymi informacjami i udostępnienia ich w postaci wymaganej przez aplikację. Korzystając z widoków na bazę wiedzy, aplikacja może "widzieć" Internet jako pojedyncze źródło wiedzy.
-
Scalar- and vector-source wave equations
PublicationW analizie zjawisk akustyki liniowej i obliczeniach pola, powszechnie stosowane są równania falowe skalarne dotyczące ciśnienia akustycznego lub potencjału prędkości, natomiast rzadko są choćby tylko wspominane równania wektorowe operujące prędkością cząstek. Jest to przejaw asymetrii w traktowaniu skalarnych i wektorowych wielkości akustycznych. Artykuł przypomina dwa zestawy dualnych równań falowych, jednorodnych i niejednorodnych,...
-
New type T-Source inverter
Publication -
Selected dried fruits as a source of nutrients
Publication -
Dietary antioxidants as a source of hydrogen peroxide
PublicationStudies of 54 antioxidants revealed that 27 of them, mainly polyphenols, generated hydrogen peroxide (H2O2) when added to Dulbecco’s modified Eagle’s medium (DMEM), other media used for culture of mammalian and yeast cells and phosphate-buffered saline. The most active antioxidants were: propyl gallate (PG), (−)-epigallocatechin gallate (EGCG) and quercetin (Q). Chelex treatment and iron chelators decreased H2O2 generation suggesting...
-
Evaluation of Open Source SIEM for Situation Awareness Platform in the Smart Grid Environment
PublicationThe smart grid as a large-scale system of systems has an exceptionally large surface exposed to cyber-attacks, including highly evolved and sophisticated threats such as Advanced Persistent Threats (APT) or Botnets. When addressing this situation the usual cyber security technologies are prerequisite, but not sufficient. The smart grid requires developing and deploying an extensive ICT infrastructure that supports significantly...
-
A negative effect of carbon phase on specific capacity of electrode material consisted of nanosized bismuth vanadate embedded in carbonaceous matrix
PublicationLithium-ion batteries (LIBs) are widely used all over the world. The LIBs belong to a renewable energy source and energy storage devices. The increase in energy demand causes that new materials of higher energy and higher power densities are still under investigation. Herein, we compare electrochemical properties of bismuth vanadate (BiVO4) embedded and not embedded into carbonaceous matrix as an anode material along with structural...
-
Numerical methodology for evaluation the combustion and emissions characteristics on WLTP in the light duty dual-fuel diesel vehicle
PublicationThe worldwide aim of reducing environmental impact from internal combustion engines bring more and more stringent emission regulations. In 2017 by EU has been adopted new harmonized test procedure called WLTP. In general terms this test was designed for determining the levels of harmful emissions and fuel consumption of traditional and hybrid cars. This procedure contains specific driving scenarios which representing reallife driving...
-
Processing, Performance Properties, and Storage Stability of Ground Tire Rubber Modified by Dicumyl Peroxide and Ethylene-Vinyl Acetate Copolymers
PublicationIn this paper, ground tire rubber was modified with dicumyl peroxide and a variable content (in the range of 0–15 phr) of ethylene-vinyl acetate copolymers characterized by different vinyl acetate contents (in the range of 18–39 wt.%). Modification of ground tire rubber was performed via an auto-thermal extrusion process in which heat was generated during internal shearing of the material inside the extruder barrel. The processing,...
-
Numerical Analysis of Mice Carotid Arteries’ Response Emphasizing the Importance of Material Law Constants’ Validation
PublicationIn this paper, a detailed validation of the passive material properties of mice carotid arteries and constants of the Fung and Holzapfel hyperelastic material laws is conducted by means of static nonlinear FEM analyses. The response of the carotid arteries in an inflation test is studied here for the following mouse models: wild-type, mdx, sgcd−/−, Eln+/+, Eln+/−, Fbln5+/+, and Fbln5−/−. All FEM computations are conducted on models...
-
Advances in analysis, quantification and modelling of N2O emission in SBRs under various DO set points
PublicationNitrous oxide (N2O), considered a major greenhouse gas (GHG) in wastewater treatment plants (WWTPs), is produced during both nitrification and denitrification processes; hence, it needs to be controlled by internal and external strategies. Various factors, such as DO, temperature, and pH, could be incorporated into the mitigation of emissions in WWTPs. In this research, potential operational strategies were investigated in order...
-
Analysis of Investments in RES Based on the Example of Photovoltaic Panels in Conditions of Uncertainty and Risk—A Case Study
PublicationThe aim of this study is to examine the profitability of investment in a photovoltaic microinstallation, to analyze the impact of legal changes on its profitability, and to perform a sensitivity analysis of the investment profitability to energy price changes. The novelty of the research applies to the financial analysis of two legal systems of discount called net-metering and net-billing. The two systems and the change in energy...
-
Innovation in the strategies of Polish provinces - a comparative study of selected cases
PublicationMany strategic management theorists and practitioners believe that the implementation of innovation is one of the key factors determining the company success and show the relationship between long-term innovation strategy and business development strategy. It has also been claimed that similar strategies should be developed for each unit of public administrationMinistry of Economy has set National Development Strategy 2007-2015...
-
Nanotubular Oxide Layer Formed on Helix Surfaces of Dental Screw Implants
PublicationSurface modification is used to extend the life of implants. To increase the corrosion resistance and improve the biocompatibility of metal implant materials, oxidation of the Ti-13Nb- 13Zr titanium alloy was used. The samples used for the research had the shape of a helix with a metric thread, with their geometry imitating a dental implant. The oxide layer was produced by a standard electrochemical method in an environment of...
-
Direction-of-Arrival Estimation Methods in Interferometric Echo Sounding
PublicationNowadays, there are two leading sea sounding technologies: the multibeam echo sounder and the multiphase echo sounder (also known as phase-dierence side scan sonar or bathymetric side scan sonar). Both solutions have their advantages and disadvantages, and they can be perceived as complementary to each other. The article reviews the development of interferometric echo sounding array configurations and the various methods applied...
-
Tacit knowledge influence on intellectual capital and innovativeness in the healthcare sector: A cross-country study of Poland and the US
PublicationThis study provides empirical proof that whole organizational innovativeness is rooted in tacit knowledge due to its potency of human capital creation and, that a learning culture composed of a learning climate and mistakes acceptance component fosters human capital development. The main practical implication is that if the IC components are externally rather than internally determined in the particular organization embedded in...
-
On the Use of Selected 4th Generation Nuclear Reactors in Marine Power Plants
PublicationThis article provides a review of the possibility of using different types of reactors to power ships. The analyses were carried out for three different large vessels: a container ship, a liquid gas carrier and a bulk carrier. A novelty of this work is the analysis of the proposal to adapt marine power plants to ecological requirements in shipping by replacing the conventional propulsion system based on internal combustion engines...
-
Do mistakes acceptance foster innovation? Polish and US cross-country study of tacit knowledge sharing in IT
PublicationAbstract Purpose – This study aims to understand and compare how the mechanism of innovative processes in the information technology (IT) industry – the most innovative industry worldwide – is shaped in Poland and the USA in terms of tacit knowledge awareness and sharing driven by a culture of knowledge and learning, composed of a learning climate and mistake acceptance. Design/methodology/approach – Study samples were drawn from...
-
CONDITIONS OF THE GREEN TRANSFORMATION. THE CASE OF THE EUROPEAN UNION
PublicationThe main purpose of the paper is to identify the factors that determine the course of green transformation and to assess the current stage and possible directions of change in subsequent years in EU countries. The literature lacks comprehensive studies that show the impact of diverse types of factors on the course of green transformation. For this purpose, two perspectives of the research – economic and environmental – are usually...
-
Electrochemical synthesis and characterization of nanocomposites based on poly(3,4-ethylenedioxythiophene) and functionalized carbon nanotubes
PublicationThis work is focused on new composite materials consisting of poly(3,4-ethylenedioxythiophene) (pEDOT) and functionalized multi-walled carbon nanotubes synthesized electrochemically. Three types of composites were synthesized: the first one containing carbon nanotubes with carboxyl groups (covalent functionalization), the second one containing oxidized carbon nanotubes ox-MWCNTs (with different oxygen-rich polar groups) (covalent...
-
Improving denitrification efficiency at the "Wschod" WWTP in Gdansk (Poland) - effects of different carbon sources
PublicationCelem badań było określenie wpływu dawkowania trzech różnych źródeł węgla (ścieków po oczyszczaniu mechanicznym, metanolu, ścieków gorzelnianych) na szybkość denitryfikacji, mierzoną w warunkach laboratoryjnych z osadem czynnym z oczyszczalni ścieków Gdańsk-Wschód. Największą szybkość procesu (4.8-5.2 mgN/(g*h)) zaobserwowano dla ścieków przemysłowych. Dodatkowo przeprowadzono badanie długości fazy adaptacji osadu do metanolu w...
-
Synergistic effects of nitrogen-doped carbon and praseodymium oxide in electrochemical water splitting
PublicationHybrid materials featuring perovskite-type metal oxide in conjunction with heteroatom-doped graphene hold immense promise as alternatives to costly noble metal catalysts for electrochemical water splitting, facilitating the generation of environmentally friendly hydrogen. In this study, perovskite-type oxide containing praseodymium, barium, strontium, cobalt, and iron atoms dispersed in a carbon matrix as a catalyst is synthesized...