Filters
total: 864
filtered: 682
Search results for: ARCHIVES
-
STRUCTURE AND MAGNETIC PROPERTIES OF Bi5Ti3FeO15 CERAMICS PREPARED BY SINTERING, MECHANICAL ACTIVATION AND EDAMM PROCESS. A COMPARATIVE STUDY
PublicationThree different methods were used to obtain Bi5Ti3FeO15 ceramics, i.e. solid-state sintering, mechanical activation (MA) with subsequent thermal treatment, and electrical discharge assisted mechanical milling (EDAMM). The structure and magnetic properties of produced Bi5Ti3FeO15 samples were characterized using X-ray diffraction and Mössbauer spectroscopy. The purest Bi5Ti3FeO15 ceramics was obtained by standard solid-state sintering...
-
A New Microwave Ceramic – Polymer Composite with 0-3 Connectivity
PublicationGoal of the present research was to fabricate and study two-phase BiNbO4//PVDF composites with 0-3 connectivity. Such composite consists of there-dimensionally connected polymer matrix loaded with dielectric ceramic particles. In the present case BiNbO4 powder acted as an active phase (dispersed phase) whereas polyvinylidene fluoride (PVDF) acted as a non-active (passive) phase (matrix). BiNbO4//PVDF composites with the volume...
-
Low temperature broad band dielectric spectroscopy of multiferroic Bi6Fe2Ti3O18 ceramics
PublicationIn the present research the tool of broadband dielectric spectroscopy was utilized to characterize dielectric behavior of Bi6Fe2Ti3O18 (BFTO) Aurivillius-type multiferroic ceramics. Dielectric response of BFTO ceramics was studied in the frequency domain (Δν=0.1Hz – 10MHz) within the temperature range ΔT=-100°C – 200°C. The Kramers-Kronig data validation test was employed to validate the impedance data measurements and it was found...
-
Fabrication and Crystal Structure of Sol-Gel Deposited BST Thin Films with Compositional Gradient
PublicationIn the present research technology of compositionally graded barium strontium titanate Ba1-xSrxTiO3 thin films deposited on stainless steel substrates by sol-gel spin coating followed with thermal annealing at T = 650°C is reported. Results of thermal behavior of the sol-gel derived powders with compositions used for fabrication of graded structure (i.e. with Sr mole fraction x = 0.5, 0.4 and 0.3) are described. X-ray diffraction...
-
INFLUENCE OF BISMUTH CONTENT ON COMPLEX IMMITTANCE CHARACTERISTICS OF PRESSURELESS SINTERED BiNbO4 CERAMICS
PublicationGoal of the present research was to study immittance properties of BiNbO4 ceramics fabricated by the solid state reaction route followed by pressureless sintering. Four sets of samples were examined, namely the one fabricated from the stoichiometric mixture of oxides, viz. Bi2O3 and Nb2O5 as well as the ones with an excess of 3%, 5% and 10% by mole of Bi2O3. The immittance properties were studied by impedance spectroscopy. Measurements...
-
Styrene Oxidation by Copper(II) Complexes Salen-Type Encapsulated into Nay Zeolite
PublicationThe copper(II) complex with a Schiff-base salen-type ligand has been encapsulated in the nanopores of a NaY zeolite by using two different methodologies, the flexible ligand and in situ complex preparation methods. The encapsulated and non-encapsulated copper(II) complexes were screened as catalysts for styrene oxidation by using TBHP as the oxygen source in acetonitrile solvent. Under the optimized conditions, the catalysts exhibited...
-
Styrene epoxidation over heterogeneous manganese(III) complexes
PublicationThe manganes(III) complex functionalised with 2,3-dihydropyridazine has been encapsulated in the supercages of the NaY zeolite using two different procedures, flexible ligand and in situ complex. The parent zeolite and the encapsulated manganese(III) complexes were screened as catalysts for styrene oxidation by using t-BOOH as the oxygen source in acetonitrile. Under the optimized conditions, the catalysts exhibited moderate activity...
-
Influence of Processing Conditions on Crystal Structure of Bi6Fe2Ti3O18 Ceramics
PublicationAim of the present research was to apply a solid state reaction route to fabricate Aurivillius-type ceramics described with the formula Bi6Fe2Ti3O18 (BFTO) and reveal the influence of processing conditions on its crystal structure. Pressureless sintering in ambient air was employed and the sintering temperatures were 850 and 1080 °C. It was found that the fabricated BFTO ceramics were multiphase ones. They consisted of two Bim+1Fem-3Ti3O3m+3...
-
Mechanical Properties of Aluminium Bracket Strengthening
PublicationThe aim of the research is laboratory investigation of aluminium brackets employed to fasten lightweight curtain walls to building facilities. Tensile loads perpendicular to end plates (vertical) were applied here. The author focused on the solutions intended to increase the load-carrying capacity of aluminium brackets applying the plain washer form A (DIN 125; ISO 7089), plain washer with an outer diameter about 3d (DIN 9021;...
-
Intergranular Corrosion Detection Using Electromagnetic Transducers for Ultrasonic Testing
PublicationThe aim of this paper is to create a research methodology that allows a quick analysis of the structural state of high alloy austenitic steels using non-destructive ultrasonic tests, in contrast to destructive standard methods. Electromagnetic acoustic transducers (EMAT) are used to generate and receive the ultrasonic wave and detect the microstructural changes caused by sample sensitization in elevated temperature, even after...
-
A comprehensive approach to double inverted pendulum modelling
PublicationThe problem of mathematical modelling and indication of properties of a DIP has been investigated in this paper. The aim of this work is to aggregate the knowledge on a DIP modelling using the Euler-Lagrange formalism in the presence of external forces and friction. To indicate the main properties important for simulation, model parameters identification and control system synthesis, analytical and numerical tools have been used....
-
Induced sheath voltages in 110 kV power cables – case study
PublicationThis paper considers electric shock hazard due to induced sheath voltages in 110 kV power cables. The purpose of this paper is to find an optimal configuration of the power cable system, taking into account electric shock hazard and ability of the system to transfer maximal power. A computer simulations on a computer model of the local power system, comprising high voltage power cables, were carried out. This model enables to analyse...
-
Equitable and semi-equitable coloring of cubic graphs and its application in batch scheduling
PublicationIn the paper we consider the problems of equitable and semi-equitable coloring of vertices of cubic graphs. We show that in contrast to the equitable coloring, which is easy, the problem of semi-equitable coloring is NP- complete within a broad spectrum of graph parameters. This affects the complexity of batch scheduling of unit-length jobs with cubic incompatibility graph on three uniform processors to minimize...
-
Multi-region fuzzy logic controller with local PID controllers for U-tube steam generator in nuclear power plant
PublicationIn the paper, analysis of multi-region fuzzy logic controller with local PID controllers for steam generator of pressurized water reactor (PWR) working in wide range of thermal power changes is presented. The U-tube steam generator has a nonlinear dynamics depending on thermal power transferred from coolant of the primary loop of the PWR plant. Control of water level in the steam generator conducted by a traditional PID controller...
-
PROBABILISTIC ANALYSIS OF A SPACE TRUSS BY MEANS OF A MULTIDIMENSIONAL VARIABLE DESCRIPTION
PublicationThe objective of this paper is to present a variant of the point estimate method (PEM) to determine mean values and standard deviations of limit loads of engineering structures. This approach is illustrated by limit state analysis of a space truss, considering geometric and material imperfections. The calculations were performed for different random models, so the influence of random parameters on the limit load of the truss can...
-
Correlations between organic pollution indicators in municipal wastewater
PublicationThe paper presents the results of a study of parameters used for determining the amount of organic pollutants in wastewater flowing into a collective wastewater treatment plant with a population equivalent of about 120 000 PE. The plant constituted part of a sewage system. Assays were performed for biochemical oxygen demand (BOD5), chemical oxygen demand (CODCr), permanganete index (CODMn) and total organic carbon (TOC). In addition,...
-
The structurally similar TRFH domain of TRF1 and TRF2 dimers shows distinct behaviour towards TIN2
PublicationThe telomere repeat binding-factor 1 and 2 (TRF1 and TRF2) proteins of the shelterin complex bind to duplex telomeric DNA as homodimers, and the homodimerization is mediated by their TRFH (TRF-homology) domains. We performed molecular dynamic (MD) simulations of the dimer forms of TRF1TRFH and TRF2TRFH in the presence/absence of the TIN2TBM (TIN2, TRF-interacting nuclear protein 2, TBM, TRF-binding motif) peptide. The MD results...
-
The 90th Birthday Jubilee of Professor Eugeniusz Bielewicz
PublicationOn the jubilee year of the 90th birthday of prof. Eugeniusz Bielewicz, a portrait of this eminent civil engineer and scholar is presented by his co-workers.
-
Effect of Semiconductor Element Substitution on the Electric Properties of Barium Titanate Ceramics
PublicationThe investigated ceramics were prepared by a solid-state reaction from simple oxides and carbonates with the use of a mixed oxide method (MOM). The morphology of BaTi0.96Si0.04O3 (BTSi04) ceramics was characterised by means of a scanning electron microscopy (SEM). It was found that Si+4 ion substitution supported the grain growth process in BT-based ceramics. The EDS results confirmed the high purity and expected quantitative composition...
-
Numerical and Analytical Investigation of Aluminium Bracket Strengthening
PublicationThis paper focuses on an analytical and numerical investigation of aluminium brackets used to fasten light-weight curtain walls to building facilities. The authors propose a solution to increase the load capacity of aluminium brackets by means of additional cover plates (straps). This paper also includes a short survey of literature and material properties concerning the EN AW-6060 T6 aluminium alloy. This paper suggests an initiation...
-
Non-proportional full-order Luenberger observers of induction motors
PublicationThe paper recapitulates recently conducted investigations of non-proportional Luenberger observers, applied to reconstruction of state variables of induction motors. Three structures of non-proportional observers are analyzed, a proportional-integral observer, modified integral observer and observer with integrators. Criteria for gain selection of the observer are described, classical ones based on poles, as well as additional,...
-
Laser granulometer as an useful tool for selection of appropriate membranes used in the MIEX®DOC-UF/MF hybrid process
PublicationIn the study, particle size distribution of the MIEX® resin was presented. Such analyses enable to determinate whether presence of fine resin fraction may be the reason for unfavorable membrane blocking during water purification by the hybrid MIEX®DOC-microfiltration/ultrafiltration systems. Granulometric analysis of resin grains using the laser diffraction particle size analyzer (laser granulometer) was carried out as well as...
-
Mobile devices and computing cloud resources allocation for interactive applications
PublicationUsing mobile devices such as smartphones or iPads for various interactive applications is currently very common. In the case of complex applications, e.g. chess games, the capabilities of these devices are insufficient to run the application in real time. One of the solutions is to use cloud computing. However, there is an optimization problem of mobile device and cloud resources allocation. An iterative heuristic algorithm for...
-
ENVIRONMENTAL DEGRADATION OF DISSIMILAR AUSTENITIC 316L AND DUPLEX 2205 STAINLESS STEELS WELDED JOINTS
PublicationThe paper describes structure and properties of dissimilar stainless steels welded joints between duplex 2205 and austenitic 316L steels. Investigations were focused on environmentally assisted cracking of welded joints. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement was determined in slow strain rate tests (SSRT) with the strain rate of 2.2 × 10–6 s–1. Chloride-inducted SCC was determined in the...
-
Comparative analysis of coaxial magnetocumulative generators
PublicationThis paper presents the results of a computer simulation of coaxial magnetocumulative current generators (MCGs). The simulation tests were carried out for different values of the internal diameter, length and speed of the deformation of the MGP element.
-
Frequency and time domain characteristics of digital control of electric vehicle in-wheel drives
PublicationIn-wheel electric drives are promising as actuators in active safety systems of electric and hybrid vehicles. This new function requires dedicated control algorithms, making it essential to deliver models that reflect better the wheel-torque control dynamics of electric drives. The timing of digital control events, whose importance is stressed in current research, still lacks an analytical description allowing for modeling its...
-
DYNAMIC RESPONSE OF FORUM GDANSK STRUCTURE DUE TO RAIL TRAFFIC
PublicationThe paper presents the study of the impact of vibration induced by the movement of the railway rolling stock on the Forum Gdańsk structure. This object is currently under construction and is located over the railway tracks in the vicinity of the Gdańsk Główny and Gdańsk Śródmieście railway stations. The analysis covers the influence of vibrations on the structure itself and on the people within. The in situ measurements on existing...
-
Damage Analysis of Tensioning Cable Anchorage Zone of a Bridge Superstructure, Using CDP Abaqus Material Model
PublicationNumerical analysis of the tensioning cables anchorage zone of a bridge superstructure is presented in this paper. It aims to identify why severe concrete cracking occurs during the tensioning process in the vicinity of anchor heads. In order to simulate the tensioning, among others, a so-called local numerical model of a section of the bridge superstructure was created in the Abaqus Finite Element Method (FEM) environment. The...
-
An assessment of health status and health behaviours in adolescents: main points and methods of the SOPKARD-Junior programme.
PublicationThe study involved preparing and implementing a model of screening assessments for adolescents and comparison of anthropometric examinations between the population of the SOPKARD-Junior programme and representative sample of Polish children in the same years.Additionally, data concerning attendance rates for particular examinations carried out under SOPKARD-Junior programme were presented.Revier2,comment 1
-
Equitable coloring of graphs. Recent theoretical results and new practical algorithms
PublicationIn this paper we survey recent theoretical results concerning conditions for equitable colorability of some graphs and recent theoretical results concerning the complexity of equitable coloring problem. Next, since the general coloring problem is strongly NP-hard, we report on practical experiments with some efficient polynomial-time algorithms for approximate equitable coloring of general graphs.
-
Model of the double-rotor induction motor in terms of electromagnetic differential
PublicationThe paper presents a concept, a construction, a circuit model and experimental results of the double-rotor induction motor. This type of a motor is to be implemented in the concept of the electromagnetic differential. At the same time it should fulfill the function of differential mechanism and the vehicle drive. One of the motor shafts is coupled to the direction changing mechanical transmission. The windings of the external rotor...
-
Improving sensitivity of residual current transformers to high frequency earth fault currents
PublicationFor protection against electric shock in low voltage systems residual current devices are commonly used. However, their proper operation can be interfered when high frequency earth fault current occurs. Serious hazard of electrocution exists then. In order to detect such a current, it is necessary to modify parameters of residual current devices, especially the operating point of their current transformer. The authors proposed...
-
Automotive fleet repair facility wastewater treatment using air/ZVI and air/ZVI/H2 O2 processes
PublicationAdvanced automotive fl eet repair facility wastewater treatment was investigated with Zero-Valent Iron/Hydrogen Peroxide (Air/ZVI/H2 O2 ) process for different process parameters: ZVI and H2 O2 doses, time, pH. The highest Chemical Oxygen Demand (COD) removal effi ciency, 76%, was achieved for ZVI/H2 O2 doses 4000/1900 mg/L, 120 min process time, pH 3.0. COD decreased from 933 to 227 mg/L. In optimal process conditions odor and...
-
Curb-to-Barrier Face Distance Variation an a TB51 Bridge Barrier Crash Test Simulation
PublicationThis paper addresses the problem of road safety regarding barrier placement as relative to the curb. A short summary of existing regulations is presented. Numerical simulations using the explicit finite element system Ls- Dyna are shown. In the analysis, variable distance between the barrier and the curb is assumed. The obtained result reveals that the distance has little impact on the working width of the barrier.
-
The Influence of the Chemical Composition of Selected Waste Materials from the Production of Copper on the Final Environmental Assessment
PublicationThis article presents qualitative and quantitative analysis of the waste produced by KGHM Polska Miedź. The waste has been analyzed according to its chemical composition and balanced in order to be reused and recycled. Special attention has been paid to mining industries producing the biggest amount of waste and ore enrichment businesses generating waste, which isn’t reused nowadays. Laboratory reseach has been conducted on floatation...
-
Simulation of the remanence influence on the transient states in a single-phase multiwinding transformer
PublicationThis paper presents the mathematical model of a single-phase multi-winding core type transformer taking into account magnetic hysteresis phenomenon based on the feedback Preisach model (FPM). The set of loop differential equations was developed for a K-th winding transformer model where the flux linkages of each winding includes flux Φ common to all windings as a function of magneto motive force Θ of all windings. The first purpose...
-
Moment resistance of I-section end-plate roof girder splices; a case study
PublicationThis article deals with the problem of determining the resistance of end-plate connections. A nonlinear FEM model of the joint was constructed in order to predict its carrying capacity. A standard code procedure was done as well. The analyses have been done to assess atypical end-plate joints designed and constructed as a part of roof structures.
-
Computing internodal conductivities in numerical modeling of two dimensional unsaturated flow on rectangular grid
PublicationW artykule porównano rozwiązania numeryczne dwuwymiarowego równania przepływu nienasyconego z użyciem różnych metod uśredniania współczynnika przewodności hydraulicznej między sąsiednimiwęzłami. Uwzględniono średnia arytmetyczną, geometryczną, "pod prad" oraz całkową, a także niedawno zaproponowany sposób uśredniania oparty na analizie przepływu ustalonego. Ten ostatni sposób okazałsię najbardziej uniwersalny, gdyż umożliwiał otrzymanie...
-
A graphical approach to yield and boundary surfaces of selected hypoplastic constitutive equations
PublicationThe article describes how to identify the boundary and yield surface for hypoplastic constitutive equations proposed by Wu, Gudehus and Bauer. It is shown how to identify and plot the surfaces for any equation in this class. Calculation errors are analyzed characteristic for appleid set of numerical formulas. In the paper there are computer links to the source code prepared in the MATLAB system, based on istructions in the article....
-
Electrophysiological features in patients with sinus node dysfunction and vasovagal syncope
PublicationThe aim of the study was to identify electrophysiological criteria that can be used for identification of patients with sinus node dysfunction and concurrent vasovagal syncope.
-
Advanced field investigations of screw piles and columns
PublicationPrzedstawiono opis badań pali i kolumn wkręcanych na terenowym poletku doświadczalnym, wykonanych w ramach projektu badawczego MNiSW. Badania statyczne pali i kolumn wykonano z zaawansowanym systemem do pomiaru rozkładu siły wzdłuż trzonów. Przedstawiono podstawowe wyniki badań z rozdziałem obciążenia na podstawę i pobocznicę pali i kolumn.
-
The results of analyses of deep excavation walls using two different methods of calculation
PublicationPrzedstawiono wyniki obliczeń obudowy głębokiego wykopu dwukrotnie rozpieranej i dwukrotnie kotwionej w gruncie jednorodnym niespoistym. Obliczenia numeryczne wykonano metodą podpór sprężysto-plastycznych i metodą elementów skończonych. Zwrócono uwagę na istotne różnice w wynikach obliczeń. Zaproponowano wyjaśnienie przyczyn zaobserwowanych różnic w wynikach obliczeń otrzymanych z obu metod.
-
Monte Carlo simulations of the fracture resistance degradation of asphalt concrete subjected to environmental factors
PublicationThe paper presents the results of laboratory tests of SCB (semi-circular beam) samples of asphalt concrete, subjected to the destructive effect of water and frost as well as the aging processes. The determined values of material parameters show significant dispersions, which makes the design of mixtures difficult. Statistical analysis of the test results supplemented by computer simulations made with the use of the proprietary...
-
Influence of cyclic frozen and defrost on mechanical properties of polytetrafluoroethylene (PTFE)-coated woven fabrics
PublicationThis research aims to determine the influence of the cyclic process of freezing and defrosting on the mechanical properties of the chosen glass fibres and PTFE-coated woven fabrics. The specimens were subjected to freezing at about −20 °C for 4 h and thawing by full immersion into the water at about +20 °C for 4 h. The fabric samples after 25 and 50 frozen cycles were air-dried at room temperature for one week and then subjected...
-
Process control of air stream deodorization from vapors of VOCs using a gas sensor matrix conducted in the biotrickling filter (BTF)
PublicationThis article presents the validity, advisability and purposefulness of using a gas sensor matrix to monitor air deodorization processes carried out in a peat-perlite-polyurethane foam-packed biotrickling filter. The aim of the conducted research was to control the effectiveness of air stream purification from vapors of hydrophobic compounds, i.e., n-hexane and cyclohexane. The effectiveness of hydrophobic n-hexane and cyclohexane...
-
Practical aspects of testing superconducting electromagnets by the capacitor discharge method taking into account the non-linearity of circuit parameters
PublicationThe article presents selected issues related to the development and testing of the diagnostics systems dedicated for superconducting electromagnets. The systems were constructed to assess the production quality of superconducting electromagnets of the SIS100 synchrotron, a new accelerator being built as part of the Facility of Antiproton and Ion Research (FAIR). One of the systems is used for automatic checking of electrical connection...
-
Discrete identification of continuous non-linear and non-stationary dynamical systems that is insensitive to noise correlation and measurement outliers
PublicationThe paper uses specific parameter estimation methods to identify the coefficients of continuous-time models represented by linear and non-linear ordinary differential equations. The necessary approximation of such systems in discrete time in the form of utility models is achieved by the use of properly tuned `integrating filters' of the FIR type. The resulting discrete-time descriptions retain the original continuous parameterization...
-
Settlement of a historic building due to seepage-induced soil deformation
PublicationThe research paper reviews issues associated with the impact of groundwater flow on soil characteristics and parameters, hence, the entire structure of a building set on it. Water seepage through the ground, building subsoil or structural elements of buildings made of soil affects the soil skeleton and may lead to changes in the arrangement of individual grains relative to each other, i.e., a modified soil structure. Soil solid...
-
Effect of different ventilation systems on air quality, heat consumption and psycho-physical comfort in modern residential buildings
PublicationArtykuł omawia wpływ różnych systemów wentylacji na jakość powietrza, zużycie ciepła i komfort psychiczno-fizyczny w nowoczesnych domach mieszkalnych na terenie Niemiec. Badania wykonano na kompleksie domków jednorodzinnych. Zbadano wpływ 4 systemów wentylacji.
-
Numerical simulations of granular material flow in silos with and without insert
PublicationArtykuł omawia wyniki naporu materiału sypkiego podczas przepływu w silosach z i bez wkładek. Obliczenia wykonano wykorzystując sformułowanie ale na bazie prawa sprężysto-plastycznego według druckera-pragera. Zbadano wpływ kształtu i położenia wkładki na wielkość naporu i rodzaj przepływu.