displaying 1000 best results Help
Search results for: INDUCTION MOTOR DRIVES, SLIDING‐MODE, SPEED OBSERVER, VARIABLE SPEED
-
EMC disturbances in connection of driving system
PublicationIt is known the steep voltage changes caused by IGBT frequency inverters may cause some electromagnetic problems in driving system. Special dU/dt type as well as sinusoidal filters are used in order to limit the level of the disturbances. The paper presents investigation results of EMC disturbances in inverter supplied induction motor. Experiments have proved that disturbances in current connection differ essentially. Important...
-
Integrated Three-Level Dual-Phase Inverter
PublicationIn view of reducing the number of inverter legs that provide dual-phase, three-level output voltages (as may be needed in an uninterruptible power supply), and that also provide a wide range of output frequencies (as needed in an advanced motor drive system with wide speed ranges), a three-level, dual-phase inverter topology is presented in this paper. Its three-level attribute was based on the F-type inverter topological concept,...
-
Destruction of AFM probes during normal operation
Open Research DataThe quality of the images obtained with the use of an atomic force microscope is determined by the state of the blade interacting with the tested material. Image artifacts can be generated by various reasons, such as oxidation, contamination or an error in blade fabrication, but also appear as a result of the repeated scanning process and inevitable...
-
Chip suction system in circular sawing machine: empirical research and computational fluid dynamics numerical simulations
PublicationThe experimental analysis of the wood chip removing system during its redesigning in the existing sliding table circular saw and computational fluid dynamic (CFD) numerical simulations of the air flow process is presented in the paper. The attention was focused on the extraction hood and the bottom shelter of the actual existing system. The main aim was to perform experimental research on the pressure distribution inside the...
-
ANALYSIS OF POSSIBILITIES FOR THE USE OF VOLUME-DELAY FUNCTIONS IN THE PLANNING MODULE OF THE TRISTAR SYSTEM
PublicationTravel time is a measure commonly used for traffic flow modelling and traffic control. It also helps to evaluate the quality of traffic control systems in urban areas. Traffic control systems that use traffic models to predict changes and disruptions in vehicle flows have to use vehicle speed-prediction models. Travel time estimation studies the effects of traffic volumes on a street section at an average speed. The TRISTAR Integrated...
-
Radio Channel Measurements in 868 MHz Off-Body Communications in a Ferry Environment
PublicationIn this paper, a characterization of the 868 MHz off-body radio channel in BANs is presented. Measurements were carried out in a ferry environment using a specific set-up. A method for path loss using radio distance measurements (RDMs) was developed. It allows to automate the measurements process and make it independent from the variable speed of a moving person. Based on the observed path loss as a function of distance, the obtained...
-
Vibration surveillance for efficient milling of flexible details fixed in adjustable stiffness holder
PublicationThe paper presents the results of research related to the possibility of using an intelligent workpiece holder with adjustable stiffness, during end milling process. Machining a one side supported flexible workpiece will be performed with constant spindle speed and feed speed. In order to avoid hazardous vibration, stiffness of the especially designed spring (mounted in a workpiece holder) will be modified off-line. In order to...
-
Nanostructures fabrication with use of electrical AFM litography
Open Research DataIn the last 10 years, one of the nanotechnological trends has been observed, consisting in the development of new variants of computer memory systems with high capacity and speed of access, using quantum dots. One of the techniques for creating nanodots and other nanostructures is based on the use of an atomic force microscope acting as a lithographic...
-
Condition-Based Monitoring of DC Motors Performed with Autoencoders
PublicationThis paper describes a condition-based monitoring system estimating DC motor degradation with the use of an autoencoder. Two methods of training the autoencoder are evaluated, namely backpropagation and extreme learning machines. The root mean square (RMS) error in the reconstruction of successive fragments of the measured DC motor angular-frequency signal, which is fed to the input of autoencoder, is used to determine the health...
-
Comparative analysis of coaxial magnetocumulative generators
PublicationThis paper presents the results of a computer simulation of coaxial magnetocumulative current generators (MCGs). The simulation tests were carried out for different values of the internal diameter, length and speed of the deformation of the MGP element.
-
SEM examination of surface layer of C45 steel after grinding on defferent depth
Open Research DataFerrite examination for the medium carbon structural steel with low content of Mn, Si, Cu, Cr and Ni after its grinding to a depth of 2 µm, 8 µm, 14 µm and 20 µm, at constant wheel circumferential speed of vs = 25 m/s and constant feed rate vft = 1 m/min. It was shown that the grinding of C45 steel causes strong work hardening of ferrite in surface...
-
The Doppler effect in a bistatic system for determining the position of moving targets
PublicationThe article presents the theoretical analysis and the results of numerical calculations of the Doppler effect it occurs in a system designed to determine the position and speed of a moving target. The transmitter is the source of the signal and it emits a sinusoidal, acoustic and continuous wave. Signal reflected off a moving target is received by four hydrophones. Based on the signals, four Doppler shifts are determined and inserted...
-
Experiment-aided virtual prototyping to minimize tool-workpiece vibration during boring of large-sized structures
PublicationThe paper presents the author's method of solving the problems of vi-bration suppression during boring of large-sized workpieces by means of an in-novative method of adjusting the rotational speed of the boring bar. It consists in selecting the spindle speed in accordance with the results of the cutting process simulation. The method includes identification of the model of the finite element method of the boring bar. The Root Mean...
-
Performance Characteristics of a Micro-turbine, International
Publication. In the paper a design of a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of particular experimental investigations and numerical calculations are shown, followed by conclusions. The co-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The values of the main cycle parameters were as follows:- heat...
-
Performance Characteristics of a Micro-Turbine
PublicationIn the paper a design of a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of particular experimental investigations and numerical calculations are shown, followed by conclusions. The co-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The values of the main cycle parameters were as follows:heat output:...
-
Impact and stretching standardized tests as useful tools for assessment of viscoelastic behavior for highly rubberized asphalt binder
PublicationAsphalt binder is generally identified as a brittle material at low service temperature or under high-speed load, and the brittleness becomes serious after weathering aging. Improving the toughness of asphalt binder through adding high-content of crumb tire rubber is an efficient method to solve this problem. Devulcanized rubber modified asphalt binder (DRMA) with different contents (15–40%) of devulcanized rubber (DR) were prepared...
-
Determining and visualizing safe motion parameters of a ship navigating in severe weather conditions
PublicationThe paper presents a method of determining, organizing and displaying ship collision avoidance information, which is based on the Collision Threat Parameters Area (CTPA) technique. The method makes it possible to visualize navigational threats as well as possible collision avoidance manoeuvres. The solution is focused on supporting navigation in severe weather conditions. Normally collision avoidance decisions are made taking into...
-
Method of estimating the rolling resistance coefficient of vehicle tyre using the roller dynamometer
PublicationThe tendency in the past few years has been to introduce tyres with lower rolling resistance coefficients to the market. This paper presents a mathematical method for determining the rolling resistance coefficients variation depending on the speed. The method uses power balance which results from automobile dynamics while rolling on chassis dynamometer. The rolling resistance coefficients of tyres obtained through ‘drum test method’,...
-
Influence of geometrical and operational parameters on tooth wear in the working mechanism of a satellite motor
PublicationThis article describes the phenomena affecting the wear of the rotor of the working mechanism in a hydraulic satellite motor. The basic geometrical relationships that allow the calculation of the coordinates of the points of contact between the satellite and the rotor and the curvature are presented. A method for calculating the number of contacts of the satellite teeth with the rotor teeth and of the satellite teeth with the curvature...
-
Evaluating the mobile robot positions using accelerometer data
PublicationThis paper analyzes the problem of determining the position of a robot using an accelerometer, which is an essential part of inertial measurement units (IMU). The information gained from such a gauge, however, requires double integration of sensor data. To assure an expected effect, a mathematical model of a low-cost accelerometer of the MEMS type is derived. Moreover, in order to improve the performance of positioning based on...
-
Evaluating the position of a mobile robot using accelerometer data
PublicationThis paper analyses the problem of determining the position of a robot using an accelerometer, which is an essential part of inertial measurement units (IMU). The information gained from such a gauge, however, requires double integration of sensor data. To assure an expected effect, a mathematical model of a low-cost accelerometer of the MEMS type is derived. Moreover, in order to improve the performance of positioning based on...
-
Studies of Nonlinear Sound Dynamics in Fluids Based on the Caloric Equation of State
PublicationThe sound speed and parameters of nonlinearity B/A, C/A in a fluid are expressed in terms of coefficients in the Taylor series expansion of an excess internal energy, in powers of excess pressure and density. That allows to conclude about features of the sound propagation in fluids, the internal energy of which is known as a function of pressure and density. The sound speed and parameters of nonlinearity in the mixture consisting...
-
VIBRATION SURVEILLANCE DURING MILLING OF FLEXIBLE DETAILS WITH A USE OF THE ACTIVE OPTIMAL CONTROL
PublicationThe main goal of modern machining operations is to achieve increasingly better performance. High Speed Machining and/or High Performance Cutting, despite a lot of advantages, have also some drawbacks, for example, a possibility of losing stability and development of self-excited chatter vibration. This paper presents an approach of vibration surveillance during high speed milling with a use of active optimal control. Non-stationary...
-
An application of acoustic sensors for the monitoring of road traffic
PublicationAssessment of road traffic parameters for the developed intelligent speed limit setting decision system constitutes the subject addressed in the paper. Current traffic conditions providing vital data source for the calculation of the locally fitted speed limits are assessed employing an economical embedded platform placed at the roadside. The use of the developed platform employing a low-powered processing unit with a set of microphones,...
-
Underwater Navigation System Based on Doppler Shifts of a Continuous Wave
PublicationThe paper describes a concept of an underwater navigation system designed to determine the location and speed of its ROVs or divers. Conducted by the Department of Marine Electronic Systems at the Gdansk University of Technology for several years, research has focused on navigation systems which determine positions on the basis of Doppler shifts of echo signals reflected from a moving object. This article presents a different version...
-
Multi-objective weather routing of sailboats considering wave resistance
PublicationThe article presents a method to determine the route of a sailing vessel with the aid of deterministic algorithms. The method assumes that the area in which the route is to be determined is limited and the basic input data comprise the wind vector and the speed characteristic of the vessel. Compared to previous works of the authors, the present article additionally takes into account the effect of sea waves with the resultant resistance...
-
Polarization-dependent optical absorption in phosphorene flakes
PublicationThe interest of 2D materials is constantly increasing because of their very attractive mechanical, electrical and optical parameters. They have been used in many applications, e.g. photodetectors, sensors, modulators, insulators. One of the recently discovered 2D materials is phosphorene. In contrast to graphene, phosphorene has a direct bandgap tuned by numbers of layers in the 2D structure. The phosphorene flakes are strongly...
-
Determination of the dynamic critical maneuvering area in an encounter between two vessels: Operation with negligible environmental disruption
PublicationThis paper introduces the concept of Collision Avoidance Dynamic Critical Area (CADCA) for onboard Decision Support Systems (DSS). The indicator proposed is derived via identification of a minimum required maneuvering zone in an encounter between two vessels. The CADCA model accounts for ship maneuvering dynamics and associated hydrodynamic actions emerging from different rudder angles and forward speed effects. The method presented...
-
Non-Salient Brushless Synchronous Generator Main Exciter Design for More Electric Aircraft
PublicationThis paper presents a prototype of high speed brushless synchronous generators (BSG) design for the application in autonomous electric power generation systems (e.g., airplane power grid). Commonly used salient pole field of the main generator part of BSG was replaced with a prototype non-salient pole field. The main objective of the research is an investigation into the advantages and disadvantages of a cylindrical field of the...
-
Consideration of dynamic loads in the determination of axle load spectra for pavement design
PublicationAxle load spectra constitute a crucial part of the data for pavement design and pavement distress analysis. Typically, axle load spectra represent static load from vehicles and do not include dynamic loads generated by vehicles in motion. While dynamic loads can significantly contribute to faster pavement distress, this fact is mostly omitted in pavement design methods. The paper presents a methodology for consideration of dynamic...
-
Measures of Functional Reliability of Two-Lane Highways
PublicationRural two-lane highways are the most common road type both in Poland and globally. In terms of kilometres, their length is by far greater than that of motorways and expressways. They are roads of one carriageway for each direction, which makes the overtaking of slower vehicles possible only when there is a gap in the stream of traffic moving from the opposite direction. Motorways and express roads are dual carriageways that are...
-
Negative impact of constant RPM control strategy on ship NOx emission in waves
PublicationIn severe wave conditions, the ship propulsion system is loaded with high fluctuations due to external disturbances. The highly fluctuating loads enforce radical changes in the main engine torque, which in turn demands variation of the fuel rate injected into the cylinders if a constant rotational speed strategy is applied. Therefore, the temperature of gases varies to a large extent during the combustion process in the cylinders....
-
The Experimental Determination of Bearings Dynamic Coefficients in a Wide Range of Rotational Speeds, Taking into Account the Resonance and Hydrodynamic Instability
PublicationMethods for the experimental determination of dynamic coefficients are commonly used for the analysis of various types of bearings, including hydrodynamic, aerodynamic and foil bearings. There are currently several algorithms that allow estimating bearing dynamic coefficients. Such algorithms usually use various excitation techniques applied to rotor–bearings systems. So far only a small number of scientific publications show how...
-
Multiobjective Aerodynamic Optimization by Variable-Fidelity Models and Response Surface Surrogates
PublicationA computationally efficient procedure for multiobjective design optimization with variable-fidelity models and response surface surrogates is presented. The proposed approach uses the multiobjective evolutionary algorithm that works with a fast surrogate model, obtained with kriging interpolation of the low-fidelity model data enhanced by space-mapping correction exploiting a few high-fidelity training points. The initial Pareto...
-
Wear in siding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specim. sets #20-#21, #22-#23, #24-#25, #26-#27, #28-#29,#30 - #31. Run time: 4-8h.
Open Research DataWear in sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer.Running time: 4-8h.Specimen sets:Specim. sets (# [upper, rotating] - #[lower, non-rotating]):#20-#21, #22-#23, #24-#25, #26-#27,...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #24 - #25.
Open Research DataSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #24 (upper, rotating), #25 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #28 - #29.
Open Research DataSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #28 (upper, rotating), #29 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Wear in siding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specim. sets #20-#21, #22-#23, #24-#25, #26-#27, #28-#29,#30 - #31. Run time: 0-4h.
Open Research DataWear in sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer.Running time: 0 - 4h.Specimen sets:Specim. sets (# [upper, rotating] - #[lower, non-rotating]):#20-#21, #22-#23, #24-#25, #26-#27,...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #30 - #31.
Open Research DataSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #30 (upper, rotating), #31 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #20 - #21.
Open Research DataSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #20 (upper, rotating), #21 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #22 - #23.
Open Research DataSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #22 (upper, rotating), #23 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #28 - #29.
Open Research DataSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #28 (upper, rotating), #29 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #26 - #27.
Open Research DataSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #26 (upper, rotating), #27 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Local basis function estimators for identification of nonstationary systems
PublicationThe problem of identification of a nonstationary stochastic system is considered and solved using local basis function approximation of system parameter trajectories. Unlike the classical basis function approach, which yields parameter estimates in the entire analysis interval, the proposed new identification procedure is operated in a sliding window mode and provides a sequence of point (rather than interval) estimates. It is...
-
AeroSense Measurements: Wind Tunnel ETH Zurich
Open Research DataData from wind tunnel tests of Aerosesne measurement system installed on NACA 0012 at ETH Zurich wind tunnel.
-
A Target Information Display for Visualising Collision Avoidance Manoeuvres in Various Visibility Conditions
PublicationThe paper introduces a new approach to displaying information on targets. The proposed display visualises three types of information: targets’ motion parameters (typical for target tracking), combinations of own course and speed which collide with those targets (typical for Collision Threat Parameters Area display by Lenart (1983)) and combinations of own course and speed which are not compliant with COLREGS in this case (based...
-
Changes in conditions of acoustic wave propagation in the Gdansk deep as an effect of climate changes in the Baltic Sea region
PublicationThe article presents the results from a research project investigating acoustic climate changes in the Gdansk Deep based on data extending from 1902 to 2019. This part of the southern Gotland Basin, is rarely discussed in the scientific literature. The speed of sound in the seawater is a function of temperature, salinity, and depth. In such shallow sea as Baltic Sea, the impact of depth is not substantial. The other two factors...
-
Analysis and design improvement of high class roads’ arched sections in Poland
PublicationAlthough Polish road network standards, in particular higher classes of roads are improving dynamically the number of fatalities on the network is still higher that EU’s average. Ensuring road safety and high maintaining standards is a complex issue and one that poses a major challenge for all road authorities. Road accidents at high speed roads characterize specially serious material and social consequences, thus research into...
-
Experimental analysis of chip removing system in circular sawing machine
PublicationPaper presents analysis of the process of removing the wood chips generated during the cutting of the material on the circular sawing machine. The attention is focused on the upper cover of the chip removing system. Within the framework of the work a systematic experimental study of pressure distribution in the cover during operation of the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm was carried...
-
Dual drive control under SVPWM, experimental results
Open Research DataThe dataset contains the experimental results of the project: A universal algorithm of space vector pulse width modulation for three-level three and multi-phase NPC inverters with DC-link voltage balancing. The analysis includes the behaviour of the drive system, examining the dynamic system response to speed and angle changes, and encompassing data...