Search results for: CONCRETE ADMIXTURES AND ADDITIVES
-
Chemical surface etching methods for ground tire rubber as sustainable approach for environmentally-friendly composites development– a review
PublicationGround tire rubber (GTR) has been used as a sustainable low-cost modifier in various composites. However, due to the hydrophobic nature of GTR, it is in compatible with most matrices and results in deterioration in both mechanical and physical properties of composites. This necessitates pre-modification of the powdered rubber to improve the interfacial bonding at the rubber-matric interface. The most common GTR modification research...
-
Integrated Application of GPR and Ultrasonic Testing in the Diagnostics of a Historical Floor
PublicationThe paper presents the results of integrated ground penetrating radar (GPR) and ultrasonic testing (UT) measurements conducted on a historical floor in St. Nicholas’ Church, Gdańsk, Poland. The described inspection was the first stage of the technical state assessment of the building. The aim of the study was the detection of underfloor air gaps, which were observed in a few trial pits. The condition of the ground under the floor...
-
Badania eksperymentalne strefy przypodporowej żelbetowych belek częściowo sprężonych
PublicationThis project refers to the study the shear zone, under full and partial prestressing in comparison to beams with passive reinforcement.For comparison, variable parameters have been determined:- a/d (from 1,5 to 3,5) - it's shear span to effective depth of the beam . Assuming constant geometrical quantities, "a" is variable.- 26 beams had no vertical shear reinforcement, and the other 26 had closed stirrups.- prestressing intensity...
-
Reduction of noise and rolling resistance by horizontal grinding of asphalt pavements
PublicationGrinding of cement concrete pavements to reduce unevenness and noise is common since a long time. Grinding is then made with wheels equipped with diamond blades rotating in the vertical plane. This creates narrow vertical/longitudinal grooves in the pavement. It is not applied to asphalt pavements. In this paper an alternative type of grinding is studied. In this case plates with diamond heads rotate in the same plane as the pavement,...
-
Investigation on Damage-Involved Structural Response of Colliding Steel Structures during Ground Motions
PublicationEarthquakes are the most unpredictable damaging loads which can affect civil engineering structures. Due to insufficient separation distance between adjacent structures with different dynamic properties, structural collisions may occur during ground motions. Although the research on structural pounding has recently been much advanced, the studies have mainly been conducted for concrete structures. The aim of this paper is to show...
-
Closing the gap – the opportunity for sustainability and smart transition in the Central and East Europe countries
PublicationFor almost half a century the countries of CEE were part of- or were remaining under the influence of- the Soviet Union what caused gaping difference in the starting line towards sustainability. Here the prefabricated concrete blocks of flats were being built at the scale unseen in the western countries. Those buildings, approximately a quarter of the residential market, are in a structurally sound condition to last another five...
-
Żółte barwniki organiczne w XIX-wiecznych farbach Jana Matejki - identyfikacja substancji barwiących, nośników, oraz wypełniaczy
PublicationNaturalne barwniki organiczne można znaleźć w wielu obiektach dziedzictwa kulturowego. Identyfikacja substancji barwiących obecnych w farbach historycznych dostarcza istotnych informacji dla wielu specjalistów zaangażowanych w naukę o sztuce. Identyfikacja składu farb pozwala na zastosowanie odpowiednich procedur dotyczących renowacji i konserwacji historycznych dzieł sztuki. Informacje te pozwalają na ich renowację zgodnie z decyzjami...
-
Doraźna nośność słupów o przekroju kołowym z rur FRP wypełnionych betonem Badania, teoria, obliczanie
PublicationPraca ma charakter monografii opisującej aktualny stan wiedzy z zakresu badań, teorii i projektowania słupów CFFT (concrete-filled fiber-reinforced polymer tube). Celem prowadzonych przez autora prac studialnych i badań własnych, w tym eksperymentalnych, jest szczegółowa analiza doraźnej nośności i zachowania się słupów CFFT poddanych ściskaniu osiowemu i mimośrodowemu. W pierwszym rozdziale wyjaśniono motywację autora do podjęcia...
-
Influence of bitumen type on cracking resistance of asphalt mixtures used in pavement overlays
PublicationCracking is one of the predominant distresses occurring in flexible pavements, especially in old pavements that were rehabilitated with an asphalt overlay. In such cases asphalt mixtures should be designed to ensure high resistance to reflective cracking because new asphalt layers are exposed to existing cracks of the old pavement. The nature of these cracks can be various (transverse, longitudinal as well as crazy cracking). One...
-
Functional Bi2O3/Gd2O3 Silica-Coated Structures for Improvement of Early Age and Radiation Shielding Performance of Cement Pastes
PublicationThis study presents a new approach towards the production of sol-gel silica-coated Bi2O3/Gd2O3 cement additives towards the improvement of early mechanical performance and radiation attenuation. Two types of silica coatings, which varied in synthesis method and morphology, were used to coat Bi2O3/Gd2O3 structures and evaluated...
-
Separation and determination of the group-type composition of modern base and lubricating oils with a wide range of polarity, especially emitted to the environment
PublicationLubricating oils are composed of base oils (>85% v/v) and enriching additives (<15% v/v). Three types of base oils may be distinguished: 1) traditional bases (obtained by low-volatile fractions from crude oil distillation refining), 2) synthetic bases (mainly poly-alpha-olefins, sometimes esters, especially succinic acid esters), 3) bases of natural origin (especially obtained from refined plant oils). The bases of natural origin...
-
Nonlinear numerical simulation of earthquake-induced pounding between timber frame buildings
PublicationEarthquakes may induce serious dynamic loads acting on buildings, which can lead to damage or even destruction of the whole structure. In densely populated areas, it is quite common that buildings are located very close one to another which can result in pounding between them during ground motions. Due to the environmental awareness, multi-story timber frame buildings are gaining popularity and therefore there is a need to investigate...
-
The Application of Granulated Expanded Glass Aggregate with Cement Grout as an Alternative Solution for Sub-Grade and Frost-Protection Sub-Base Layer in Road Construction
PublicationThe purpose of the research was to assess the possibility of using granulated expanded glass aggregate (GEGA) with cement grout as a replacement of a sub-grade and frost-protection layer, made of natural fine aggregates (NATU), stabilized with a hydraulic binder. Instead of traditional parts of the road construction, such as the sub-grade and frost-protection layer with the application of fine aggregate, stabilized with cement,...
-
Time travel without paradoxes: Ring resonator as a universal paradigm for looped quantum evolutions
PublicationA ring resonator involves a scattering process where a part of the output is fed again into the input. The same formal structure is encountered in the problem of time travel in a neighborhood of a closed timelike curve (CTC). We know how to describe quantum optics of ring resonators, and the resulting description agrees with experiment. We can apply the same formal strategy to any looped quantum evolution, in particular to the...
-
Screw displacement pile shaft deformations measured by vibrating wire and fiber optic systems during a static load test
PublicationThis paper describes a full scale static load test performed on a 400 mm diameter screw displacement pile equipped with four different strain measuring systems. Three types of vibrating wire strain gauges (VWSG) were used: global - retrievable, local attached to steel pipe and local concrete embedded. The fourth system was distributed fiber optic sensors based on Rayleigh back scattering (DFOS) - three in the pile cross section....
-
EVALUATION OF 3D MODEL OF REBAR FOR QUANTITATIVE PARAMETERS
PublicationThe construction industry practices and processes are evolving constantly, and with the emergence of Industry 4.0, the use of technologies is expanding. Construction progress monitoring is an essential project lifecycle process; project success and timely completion are linked with effective progress monitoring operations and adopted tools. In the domain of automated construction progress monitoring, 3D modeling techniques have...
-
Factors affecting low-temperature cracking of asphalt pavements: analysis of field observations using the ordered logistic model
PublicationAccurate identification of factors that primarily affect the number of low-temperature cracks is crucial for selection of road materials and planning of pavement maintenance. Field investigations of lowtemperature cracks were performed in the years 2014 and 2020 on the same 68 road sections being in service in typical traffic conditions. The collected data were statistically analysed using the ordered logistic regression model....
-
Introducing a Computational Method to Retrofit Damaged Buildings under Seismic Mainshock-Aftershock Sequence
PublicationRetrofitting damaged buildings is a challenge for engineers, since commercial software does not have the ability to consider the local damages and deformed shape of a building resulting from the mainshock record of an earthquake before applying the aftershock record. In this research, a computational method for retrofitting of damaged buildings under seismic mainshock-aftershock sequences is proposed, and proposed computational...
-
Investigation on Mode I Fracture Behavior of Hybrid Fiber-Reinforced Geopolymer Composites
PublicationRecent reports in the literature have shown that fber-reinforced geopolymer composites (FRGC) made with monofbers exhibit a signifcant enhancement in fracture energy. However, many aspects of the fracture performance of hybrid fberreinforced geopolymer composites (HFRGC) remain largely unexploited, and these are predominant for the structures. For the frst time, the mode I fracture energy of HFRGC is investigated. The mode I behavior...
-
Acoustic lifecycle study of the double-layer porous asphalt on E4 in Huskvarna, Sweden
PublicationIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed on the E4 motorway through the Swedish city Huskvarna. Earlier experience in Sweden indicated that it was feasible to obtain a high initial noise reduction but due to the widespread use of studded tires in winter, clogging and ravelling created losses of around 2 dB per year, with an expected acoustical lifetime of only 3 years. However, the improved...
-
Unfolding new values in the landscape of conflict
PublicationThe main objective of the paper is to investigate how the conflict quality of landscape can be used as its asset and potential for creating new values. Like mediation between different overlapping archaeologies offers a basis for the perception of place in the chronology of time, the mediation between conflicted areas creates a capacious zone for enhancing the unique quality of landscape in its architectural, social, cultural and...
-
Correlation between Compressive Strength and Heat of Hydration of Cement Mortars with Siliceous Fly Ash
PublicationThis paper presents the results of calorimetric and strength tests of mortars with ordinary Portland cement and two substitution rates (10 and 20%) of cement by siliceous fly ash. The prepared samples were cured under isothermal conditions at four different temperatures: 23, 33, 43 and 53 °C. Heat of hydration was measured using an isothermal calorimeter dedicated to monitor the hydration process of cementitious composites such...
-
Mechanical and physical assessment of epoxy, mineral, solvent-based, and water-soluble coating materials
PublicationThis paper assesses the behavior of mineral, epoxy (EP), solvent, and water-soluble coatings when exposed to salt and regular water for 28 days. Also, it evaluates the pull-off adhesion strength of the same coating materials applied to concrete slabs saturated with oil and water and dried with two different processes: air-dried for 28 days and air-dried for 14 days plus 14 days in the oven at 70 °C. Properties such as carbonation,...
-
Seismic damage diagnosis in adjacent steel and RC MRFs considering pounding effects through improved wavelet-based damage-sensitive feature
PublicationThis paper aims to propose complex Morlet (cmorfb-fc) wavelet-based refined damage-sensitive feature (rDSF) as a new and more precise damage indicator to diagnose seismic damages in adjacent steel and Reinforced Concrete (RC) Moment Resisting Frames (MRFs) assuming pounding conditions using acceleration responses. The considered structures include 6- and 9-story steel and 4- and 8-story RC benchmark MRFs that are assumed to have...
-
The best porous asphalt pavement in Sweden so far
PublicationIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed in various versions on the E4 motorway through the Swedish city Huskvarna. As a result of a court decision the Swedish Transport Administration had to reduce noise emission by applying a low noise road surface that would reduce A-weighted noise levels by 5 dB, as an average. Earlier experience in Sweden indicated that it was possible to obtain a high...
-
Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test
PublicationLow-temperature cracking is one of the most common road pavement distress types in Poland. While bitumen performance can be evaluated in detail using bending beam rheometer (BBR) or dynamic shear rheometer (DSR) tests, none of the normalized test methods gives a comprehensive representation of low-temperature performance of the asphalt mixtures. This article presents the Bending Beam Creep test performed at temperatures from −20...
-
Ecological and Health Effects of Lubricant Oils Emitted into the Environment
PublicationLubricating oils used in machines with an open cutting system, such as a saw or harvester, are applied in forest areas, gardening, in the household, and in urban greenery. During the operation of the device with an open cutting system, the lubricating oil is emitted into the environment. Therefore, the use of an oil base and refining additives of petroleum origin in the content of lubricants is associated with a negative impact...
-
Analiza kosztów i czasu budowy domu jednorodzinnego w technologii drewna krzyżowo klejonego CLT
Publication-
-
Analiza przyczepności prętów żebrowanych w betonie metodą pull-out na próbkach centrycznych i mimośrodowych
PublicationArtykuł dotyczy analizy przyczepności żebrowanego stalowego pręta zbrojeniowego w betonie. Celem pracy była ocena wpływu położenia pręta w betonowym bloku na lokalną zależność naprężenie przyczepności-poślizg. Podjęto także próbę numerycznej symulacji przeprowadzonych eksperymentów w programie ABAQUS. Analizę doświadczalną przeprowadzono za pomocą testu pull-out na dwóch rodzajach próbek – centrycznych i mimośrodowych w dwóch wariantach,...
-
The importance of the bottom layer in double-layer porous asphalt for noise reduction
PublicationDouble-layer porous asphalt concrete (DPAC) surfaces are generally considered to be the acoustically most effective low noise road surfaces ready for implementation. While DPAC used on highways in warm climates may have an average life of around 8 years, in Scandinavia with severe winter climate DPAC usually survive only about 3 years; partly due to wear of studded tyres. An ongoing project in Sweden, applying DPAC and single-layer...
-
Diagnostyka ultradźwiękowa mostowej belki prefabrykowanej typu T metodą młoteczkową
PublicationZastosowanie prefabrykacji w budowie obiektów mostowych pozwala optymalizować zużycie energii i materiałów i tym samym redukować koszty budowanego obiektu. Prefabrykowane belki sprężone mogą występować jako elementy kablobetonowe wykonywane bezpośrednio na placu budowy lub powstawać w zakładzie prefabrykacji jako elementy strunobetonowe. Elementy prefabrykowane wytwarzane w warunkach przemysłowych muszą spełniać wymagania wysokiej trwałości,...
-
Instalacja oświetleniowa w zbiorniku wody "Stary Sobieski" - rozważania o spektakularnym zabytku techniki
PublicationArtykuł przedstawia efekty badań autora nad niezwykle okazałą, ponad stuletnią instalacją elektryczną, która zachowała się w zabytkowym obiekcie infrastruktury wodociągowej w niemal 100% oryginalnej formie (nie licząc częściowej dewastacji). Jest to rzadki przykład tego rodzaju zabytku, ponieważ obiekty tego typu i w tym wieku zwykle podlegały modernizacji na przestrzeni lat albo, po wyłączeniu z eksploatacji zostały całkowicie...
-
Interactions of selected mono- and disaccharides with precipitated calcium carbonate particles
PublicationCalcium carbonate is a widespread compound in nature and it can be produced by living organisms in the biomineralization process. Calcite, aragonite and vaterite are anhydrous polymorphic forms of calcium carbonate, wherein the calcite is the most thermodynamically stable. Vaterite is the metastable crystalline phase, which can be a precursor of calcite and aragonite, because it can easily transformed by dissolution and re crystallization...
-
The Effect of Surface Modification of Ti13Zr13Nb Alloy on Adhesion of Antibiotic and Nanosilver-Loaded Bone Cement Coatings Dedicated for Application as Spacers
PublicationSpacers, in terms of instruments used in revision surgery for the local treatment of postoperative infection, are usually made of metal rod covered by antibiotic-loaded bone cement. One of the main limitations of this temporary implant is the debonding effect of metal–bone cement interface, leading to aseptic loosening. Material selection, as well as surface treatment, should be evaluated in order to minimize the risk of fraction...
-
Does the chemical modification of Nystatin A1 affect the drug's ability to overcome the multidrug resistance of fungi?
PublicationAlthough the contemporary medicine keeps moving forward, disseminated infections caused by fungal pathogens are an emerging challenge. The dramatic rise of fungal diseases, especially the most life-threatening systemic mycoses is associated with a permanently growing number of immunodeficient patients. Undoubted difficulties in the treatment of fungal infections are caused by lack of highly effective and selective antifungal drugs,...
-
Challenges and opportunities related to the use of sewage sludge ash in cement-based building materials – A review
PublicationDue to the increasingly demanding legal regulations, regarding both sewage sludge (SS) and solid residues obtained during its thermal utilization processes, new solutions to limit their negative impact on the environment are sought. One approach that eliminates the risk of sewage sludge ash (SSA) is its use in cement building materials. The article contains a detailed literature review regarding the use of SSA in mortars and concretes,...
-
DYNAMIC ANALYSIS OF THE RAILWAY BRIDGES IN POLAND WITH REGARDS TO HIGH-SPEED TRAINS PASSAGE ADJUSTMENT
PublicationThe dynamic analysis of the railway bridge in Tczew was carried out in the article as an example of such bridges adaptation suitability to handle high-speed trains. Calculations of railway bridges are greatly complicated and labor-consuming. The bridge model and a rolling stock passage simulation were developed in the SOFISTIK software. Three types of elements were used for the correct mapping of the structure in the calculation...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublicationThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Potential Impact of Waterway Development on Cultural Landscape Values: The Case of the Lower Vistula
PublicationThe northern (“lower”) section of the Vistula is on the route of two international waterways—E70 and E40. However, the current condition of the riverbed prevents larger vessels from passing through. Plans for the waterway date back to the beginning of the 20th century. Following Poland’s ratification of the European Agreement on Main Inland Waterways of International Importance in 2017, the general concept has been transformed...
-
FEM modelling of screw displacement pile interaction with subsoil
PublicationPredicting the-settlement characteristics of piles is an important element in the designing of pile foundations. The most reliable method in evaluating pile-soil interaction is the static load test, preferably performed with instrumentation for measuring shaft and pile base resistances. This, however, is a mostly post-implementation test. In the design phase, prediction methods are needed, in which numerical simulations play an...
-
Fragility analysis of structural pounding between adjacent structures arranged in series with various alignment configurations under near‑field earthquakes
PublicationA major cause of local to total damages is related to structural pounding in a large number of past earthquakes. In general, these collisions take place as a result of differences in the dynamic characteristics of the colliding structures. To acquire a better perception of the behavior of structures, in this paper, three structures featuring different heights are modeled in series and with various configurations next to each other...
-
Tyre/road noise reduction by a poroelastic road surface
PublicationLow noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory...
-
Building damage due to structural pounding during earthquakes
PublicationEarthquake-induced pounding between adjacent buildings has been identified as one of the reasons for substantial damage or even total collapse of colliding structures. A major reason leading to interactions in buildings results from the differences in their dynamic parameters and also from insufficient distance between the structures. Although the research on structural pounding has been much advanced, the studies have mainly been...
-
The geodetic monitoring of the engineering structure – a practical solution of the problem in 3D space
PublicationThe study raises the issues concerning the automatic system designed for the monitoring of movement of controlled points, located on the roof covering of the Forest Opera in Sopot. It presents the calculation algorithm proposed by authors. It takes into account the specific design and location of the test object. High forest stand makes it difficult to use distant reference points. Hence the reference points used to study the stability...
-
The long-term properties of mineral-cement-emulsion mixtures
PublicationThis publication presents evaluation of long-term behavior of mineral-cement-emulsion (MCE) mixtures. MCE mixtures are among the major products of cold recycling of old asphalt pavements. They are composed by binding of the old materials reclaimed from the pavement and new mineral aggregate using two different binding agents – cement and bituminous emulsion. While bituminous emulsion dissolutes and binds materials quite fast, it...
-
Sustainable utilization of copper post-flotation waste in cement composites
PublicationThe current way of managing the copper ore flotation waste is by placing it in waste neutralization facilities. However, flotation waste has great potential in application in cement composites. The article presents the detailed characteristics of post-flotation waste (PFW) and three types of cements: CEM I, CEM II/B-V, and CEM III/A, 42.5 MPa class. The post-flotation waste added for 20% of the cement mass increase the water demand...
-
Linear viscoelastic transversely isotropic model based on the spectral decomposition of elasticity tensors
PublicationThe linear viscoelasticity is still a useful model in the engineering for studying the behavior of materials loaded with different loading rates (frequencies). Certain types of materials reveal also an anisotropic behavior: fiber reinforced composites, asphalt concrete mixtures, or wood, to name a few. In general, researchers try to identify experimentally the dependence of engineering constants like: directional Young’s moduli...
-
Finite element models used in diagnostics of transverse cracks in bridge approach pavement
Open Research DataTransverse cracks in the asphalt pavement were observed on bridge structures next to single-module expansion joints with a 5 meter approach slab set at the depth of 1 m. The finite element (FE) models of the approach pavement were created to investigate the reasons of premature cracking and crack initiation mechanism over the back edge of the abutment...
-
WERYFIKACJA KONCEPCJI PRZEGUBÓW PLASTYCZNYCH PROJEKTOWANYCH NA ODZIAŁYWANIA SEJSMICZNE WIADUKTU V6 OBWODNICY ISTAMBUŁU
PublicationW pracy zawarto wyniki analiz betonowego wiaduktu V6 budowanego w ciągu obwodnicy Istambułu w Turcji realizowanego w ramach projektu Northern Marmara Highway. Przeprawę stanowią dwie niezależne nitki o skrzynkowym przekroju poprzecznym i szerokości 22,00 m. Schemat statyczny obiektu to belka dziewięcioprzęsłowa o długości całkowitej 446,86 m oparta na podporach słupowych o zmiennej sztywności (rys.1) i wysokościach zmieniających...
-
Investigation of low-temperature cracks on selected national roads and motorways in Poland 2020
Open Research DataThe dataset contains video investigation and records of 68 road sections in various parts of Poland. Videos were recorded with the use of two cameras: 1) mounted in front of measurement vehicle, which was focused on overall view of road and 2) which was focused on pavement surface. The records are categorized according to the ID of the section given...