displaying 1000 best results Help
Search results for: thermal%20imaging%20visualization
-
Experimental research on helical coil biomass boiler with oil as a heating fluid
PublicationThis paper presents an experimental research of helical coil biomass boiler with thermal oil heating agent. Heat exchanger consists of two coaxial helical coils swept by the flue gases. The burner is a single vertical retort connected to the fuel tank (wooden pellets). The boiler is a part of micro-power plant in which the heat from the boiler is exchanged with low-boiling HFE7100 to produce steam for a custom steam turbine. The...
-
Heat transfer intensification by enlarged surface roughness in the plate heat exchanger
PublicationIn the paper an experimental analysis of passive heat transfer intensification technique employed in the case of the plate heat exchanger is presented. The passive intensification was obtained by a modification of the heat transfer surface. The roughness of surface was increased by a use of glass micro-beads. Single-phase convective heat transfer in the water-water system was studied. The experiment was accomplished in two stages....
-
Ground Tire Rubber Filled Flexible Polyurethane Foam—Effect of Waste Rubber Treatment on Composite Performance
PublicationThe application range of flexible polyurethane (PU) foams is comprehensive because of their versatility and flexibility in adjusting structure and performance. In addition to the investigations associated with further broadening of their potential properties, researchers are looking for new raw materials, beneficially originated from renewable resources or recycling. A great example of such a material is ground tire rubber (GTR)—the...
-
A new method for real-time monitoring of volatiles in frying fumes using proton transfer reaction mass spectrometry with time-of-flight analyse
PublicationTo safeguard the consumers’ well-being, it is necessary to develop novel methods for determination of carcinogens in food, including volatiles generated during frying. The currently used procedures for analysis of volatile fraction of vegetable oils are not based on real-time measurements and thus do not enable the determination of carcinogenic compounds in frying fumes; instead, only the headspace or liquid fraction is sampled....
-
Application of Artificial Neural Networks to Predict Insulation Properties of Lightweight Concrete
PublicationPredicting the properties of concrete before its design and application process allows for refining and optimizing its composition. However, the properties of lightweight concrete are much harder to predict than those of normal weight concrete, especially if the forecast concerns the insulating properties of concrete with artificial lightweight aggregate (LWA). It is possible to use porous aggregates and precisely modify the composition...
-
STRUCTURE AND MAGNETIC PROPERTIES OF Bi5Ti3FeO15 CERAMICS PREPARED BY SINTERING, MECHANICAL ACTIVATION AND EDAMM PROCESS. A COMPARATIVE STUDY
PublicationThree different methods were used to obtain Bi5Ti3FeO15 ceramics, i.e. solid-state sintering, mechanical activation (MA) with subsequent thermal treatment, and electrical discharge assisted mechanical milling (EDAMM). The structure and magnetic properties of produced Bi5Ti3FeO15 samples were characterized using X-ray diffraction and Mössbauer spectroscopy. The purest Bi5Ti3FeO15 ceramics was obtained by standard solid-state sintering...
-
Microstructure and Electrical Properties of Fe,Cu Substituted (Co,Mn)3O4 Thin Films
PublicationIn this work, thin films (~1000 nm) of a pure MnCo2O4 spinel together with its partially substituted derivatives (MnCo1.6Cu0.2Fe0.2O4, MnCo1.6Cu0.4O4, MnCo1.6Fe0.4O4) were prepared by spray pyrolysis and were evaluated for electrical conductivity. Doping by Cu increases the electrical conductivity, whereas doping by Fe decreases the conductivity. For Cu containing samples, rapid grain growth occurs and these samples develop cracks...
-
Zmienność termicznego charakteru okresów zimowych w Polsce i jej przyczyny
PublicationPraca przybliża problematykę funkcjonowania fenomenu klimatycznego Oscylacji Północnego Atlantyku (Norh Atlantic Oscillation – NAO) oraz omawia jej wpływ na kształtowanie charakteru termicznego zim (grudzień – marzec) na obszarze Polski. Zmiana faz NAO z w przewadze ujemnych na w przewadze dodatnie, jaka nastąpiła w latach 1987-1989 spowodowała, że po roku 1989 obserwuje się w Polsce znaczne złagodzenie stopnia ostrości zim.
-
The role of hydrogen bonding on tuning hard-soft segments in bio-based thermoplastic poly(ether-urethane)s
PublicationThis work describes the preparation of bio-based thermoplastic poly(ether-urethane)s (TPU) via a prepolymer method and investigates the effect of varying the interphase hydrogen-bonding (H-bonding) on physicochemical, thermal and mechanical properties. This was achieved by varying the glycol type and molar ratio of [NCO]/[OH] groups used during the prepolymer chain extending step. The TPUs’ chemical structure was analyzed by Fourier...
-
Study on the Structure-Property Dependences of Rigid PUR-PIR Foams Obtained from Marine Biomass-Based Biopolyol
PublicationThe paper describes the preparation and characterization of rigid polyurethane-polyisocyanurate (PUR-PIR) foams obtained with biopolyol synthesized in the process of liquefaction of biomass from the Baltic Sea. The obtained foams differed in the content of biopolyol in polyol mixture (0–30 wt%) and the isocyanate index (IISO = 200, 250, and 300). The prepared foams were characterized in terms of processing parameters (processing...
-
Influence of Bitumen Type and Asphalt Mixture Composition on Low-Temperature Strength Properties According to Various Test Methods
PublicationIn regions with low-temperatures, action transverse cracks can appear in asphalt pavements as a result of thermal stresses that exceed the fracture strength of materials used in asphalt layers. To better understand thermal cracking phenomenon, strength properties of different asphalt mixtures were investigated. Four test methods were used to assess the influence of bitumen type and mixture composition on tensile strength properties...
-
Effects of the polyhistidine tag on kinetics and other properties of trehalose synthase from Deionococcus geothermalis
PublicationTwo recombinant trehalose synthases from Deinococcus geothermalis (DSMZ 11300) were compared. A significant influence of the artificial polyhistidine tag was observed in protein constitution. The recombinant trehalose synthase from D. geothermalis with His6 -tag has a higher K m value of 254 mM, in comparison with the wild-type trehalose synthase (K m 170 mM), and displayed a lower activity of maltose conversion when compared...
-
Cargo ships heat demand - operational experiment
PublicationThe paper presents the results of an experiment conducted on two cargo ships – a 5300 TEU container with a steam heating system and a 7500 dwt general cargo ship with a thermal oil system. On both ships research has been carried out using specially designed measuring equipment. After gathering data about flow velocity and temperatures (steam/ cooling water/ thermal oil/ seawater/ outside air), calculations have been done, resulting...
-
Power augmentation of PGE Gorzow's gas turbine by steam injection - thermodynamic overview
PublicationThe impact of steam injection upon a gas turbine and a combined power plant performance has been investigated. This article describes and summarizes possibilities of modification for current gas turbine in PGE Gorzow power plant into the Cheng cycle. Our modification deals with a thermal cycle, in which steam produced in a heat recovery steam generator is injected into the gas turbine's combustion chamber. It has been proved that...
-
Linear and branched polyester resins based on dimethyl-2,5-furandicarboxylate for coating applications
PublicationIn this study, novel bio-based hydroxyl-functional (co)polyesters from dimethyl-2, 5-furandicarboxylate (DMF), 2,3-butanediol, and a variety of comonomers viz. glycerol, pentaerythritol or trimethylolpropane are prepared using a solvent-free, bulk polycondensation technique. Extensive molecular and thermal characterization was performed to elucidate the properties of these materials. The materials showed suitable properties for solvent-borne...
-
Effect of Porosity on the Thermo-Mechanical Behavior of Friction-Stir-Welded Spark-Plasma-Sintered Aluminum Matrix Composites with Bimodal Micro- and Nano-Sized Reinforcing Al2O3 Particles
PublicationThe thermo-mechanical behavior of nanosized Al2O3 particles reinforcing aluminum was analyzed in the present paper. The material was prepared by spark plasma sintering and friction stir welding. The thermal stresses affecting the composite behavior during welding were modeled through COMSOL MultiPhysics, and the results were validated by the analyses of the composites’ mechanical properties. The spark-plasma-sintered materials...
-
Influence of plasmon resonance on the luminescence of titanium dioxide thin films doped with rare earth ions
PublicationIn this work the study of the optical properties of europium doped titanium dioxide thin films (TiO2:Eu) enhanced by gold plasmonic nanostructures are presented. Plasmonic platforms were manufactured by thermal annealing of thin film of Au, deposited on a Corning glass substrate. As a result of thermal treatment, gold spherical nanostructures with average dimensions of 50 nm were obtained. Luminescent TiO2:Eu film was deposited...
-
Effect of Nb and Al on in vitro dissolution behavior and structure of Na2O-MgO CaO-P2O5 glasses
PublicationIn vitro dissolution, structure, and thermal properties of the glass series Na2O-MgOsingle bondCaOsingle bondNb2O5 -Al2O3-P2O5 were studied. The dissolution behavior in phosphate-buffered saline (PBS) confirmed the potential bioactive properties of tested glasses. The dissolution process was found to depend on the Al, Nb, and Mg contents. Al, respectively, suppresses the Nb and accelerates the Mg release process from the glasses....
-
Partition of friction heat between sliding semispaces due to adhesion-deformational heat generation
PublicationAnalytical expressions of heat-partition coefficient and contact temperatures for two sliding semispaces with account for adhesion-deformational heat generation and contact heat exchange have been obtained. The rate of deformational heat generation is assumed to decay exponentially with increase of distance from the interface. It has been shown that heat-generation configuration and the intensity of contact heat exchange have impact...
-
Study of Soil Temperature and Moisture Changes in a Physical Model of an Underground Cable Line
PublicationThe ampacity of power cables is highly dependent on the thermal resistivity of the soil in which they are laid. The lower it is, the higher this ampacity. The thermal resistivity of the soil decreases as its moisture increases. Therefore, it is preferable that the soil around the cables has high moisture. Unfortunately, the heat generated in heavily loaded cables causes the migration of moisture from the surrounding soil, which...
-
Water uptake analysis of acceptor-doped lanthanum orthoniobates
PublicationIn this work, lanthanum orthoniobates doped with either antimony, calcium, or both have been synthesized and studied. The water uptake of the investigated materials has been analyzed by means of thermogravimetric studies. The results show the difference between the thermodynamics of hydration between the lanthanum orthoniobate system and other proton conducting ceramics. The relation between the water uptake and effective acceptor...
-
Flow boiling intensification in minichannels by means of mechanical flow turbulising inserts
PublicationThe work presents the results of experimental investigation on heat transfer in minichannels. Refrigerant R123 was used as a test fluid. Single vertical silver tubes of 380 mm length and 2.3 mm diameter were examined with two variants of turbulising inserts. A wide range of parameters was considered, namely mass flux G=534-3011 kg/(m2s), heat flux qw=28.5-68.4 kW/m2, saturation temperature Tsat=23-86 stC and the full range of vapour...
-
DSC Study of Polyurethanes obtained from 4,4'-Bis(10-Hydroxydecaoxy)biphenyl
Publication -
Experimental investigation of dryout of SES36, R134a, R123 and ethanol in vertical small diameter tubes
PublicationW publikacji przedstawiono wyniki badań eksperymentalnych kryzysu wrzenia typu dryout podczas wrzenia w przepływie czterech czynników (SES36, R134a, R123, alkohol etylowy) w kanałach o średnicy wewnętrznej 1.15 mm i 2.3 mm. Badania przeprowadzono w szerokim zakresie zmian stopnia suchości pary (0.65-1), gęstości strumienia masy (40-900 kg/(m2s)) i gęstości strumienia ciepła (20-220 kW/m2). W badaniach wykorzystano technikę termowizyjną...
-
Improvement of the resistance to oxidation of the ecological greases by the additives
Publication -
Modelling relation between oxidation resistance and tribological properties of non-toxic lubricants with the use of artificial neural networks
Publication -
Production of gaseous matrix-free reference materials
Publication -
Heat transfer enhancement through nanofluids with applications in automobile radiator
Publication -
Thermodynamics, size, and dynamics of zwitterionic dodecylphosphocholine and anionic sodium dodecyl sulfate mixed micelles
Publication -
Hydrothermal, microwave and mechanochemical modification of amorphous zirconium phosphate structure
Publication -
Active carbons from waste biochars
Publication -
Swelling effects in cross-linked polymers by thermogravimetry
Publication -
Adsorption and calorimetric studies of hydrothermally modified carbosils
Publication -
Modification of titanium phosphate precipitated from titanylsulfate
Publication -
Carbon–silica gel adsorbents
Publication -
Application of differential scanning calorimetry to study porous structure of hydrothermally modified silicas
Publication -
Synthesis and characterization of metal polycarboxylates constructed from lanthanides(iii) and 1,2,4,5-benzenetetracarboxylic acid
Publication -
Sessile droplet contact angle of water–Al2O3, water–TiO2 and water–Cu nanofluids
PublicationThis work presents measurements of the contact angle of sessile droplets for three nanofluids, i.e. water–Al2O3, water–TiO2 and water–Cu. The plates made of glass, anodized aluminium and stainless steel of different roughness served as substrates. Ultrasonic vibration was used for 30–60 min in order to stabilise the dispersion of the nanoparticles. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight....
-
Experimental study of pressure rise at the evaporator of capillary pumped loop with acetone and water as working fluids
PublicationIn this work studied is the possibility of fluid pumping using capillary forces in the capillary pumped loop. Experimental and theoretical studies have been performed to understand the phenomena associated with heat transfer in porous structure of the evaporator. The capillary effect was studied during operation of two different capillary porous structures with two different working fluids, namely water and acetone. The results...
-
Properties of polyamide 6 and thermoplastic polyurethane blends containing modified montmorillonites
PublicationAnalizie poddano nowy rodzaj mieszanin polimerowych poliamidu 6 z termoplastycznymi elastomerami poliuretanowymi. Mieszaniny wzmocniono poprzez dodatek organicznie modyfikowanych montmorylonitów (Cloisite). Uzyskane układy przebadano metodami termicznymi, dyfrakcyjnymi oraz scharakteryzowano podstawowe właściwości mechaniczne.
-
DSC study of polyurethanes obtained from 4,4´bis(10-hydroxydecaoxy) biphenyl.
PublicationW naszych badaniach nad poliuretanami segmentowymi i sztywno segmentowymi, otrzymanymi z 4,4`-bis(6-hydroksyheksyloksy)bifenylu (BHHBP), diizocyjanianu4,4`-dicykloheksylometanu (HMDI) i oligo(adypinianu 1,6-heksylenu) stwierdziliśmy, że poliuretany otrzymane z HMDI o składzie 16% trans, trans-, 52%cis, trans- i 32% cis, cis-HMDI charakteryzują się znacznie niższymi temperaturami przejść fazowych, niż te otrzymane z frakcji...
-
Experimental verification of natural convective heat transfer phenomenon from isothermal cuboids
PublicationArtykuł przedstawia wyniki badań eksperymentalnych konwekcyjnej wymiany ciepła od powierzchni izotermicznego prostopadłościanu o stosunkowo dużych rozmiarach (t.j. 1.5 m x1 m x 0.5 m). Celem tych badań było otrzymanie wyników, które można by porównać z otrzymanymi dla obiektu w mniejszej skali i prezentowano we wcześniejszych doniesieniach (Int. J. Heat Mass Transfer 46 (2003) 2169-2178). Rozwiązanie eksperymentalne przeprowadzono...
-
Circumferential temperature distribution during nucleate pool boiling outside smooth and modified horizontal tubes
PublicationPrzedstawiono wyniki badań eksperymentalnych obwodowego rozkłądu temperatury w poziomych rurkach, ogrzewanych elektrycznie na których zachodzi wrzenie pęcherzykowe. Wykazano, że lokalne - w obszarze górnej tworzącej rurki, zastosowanie powłki porowatej prowadzi do wygładzenia rozkładu temperatury oraz obniżenia średniej temperatury ścianki.
-
Production of gaseous matrix-free reference materials. Application of thermoanalytical techniques
PublicationMateriały odniesienia są wykorzystywane w każdym laboratorium w celu zapewnienia jakości wyników pomiarów analitycznych. Produkcja materiałów odniesienia nie jest zadaniem łatwym, szczególnie w przypadku składników gazowych, toksycznych i o nieprzyjemnym zapachu. Termiczny rozkład związków powierzchniowych jest bardzo dogodnym sposobem sporządzania właśnie tego rodzaju mieszanin. Ważną rolę w procesie termicznego rozkładu związków...
-
Characterization of PVC-based polymer inclusion membranes with phosphonium ionic liquids
Publication -
Temperature-dependent interactions in the chitosan/cyclosporine A system at liquid–air interface
Publication -
MgO/CaO-loaded porous carbons for carbon dioxide capture
Publication -
Desirability-based optimization of dual-fuel diesel engine using acetylene as an alternative fuel
Publicationhe study examined the dual-fuel engine performance employing acetylene gas as primary fuel and diesel as pilot fuel. The engine's operational parameters were adjusted using the Box-Behnken design, and the results were recorded. The best operating settings were yielded as 81.25 % engine load, 4.48 lpm acetylene gas flow rate and the compression ratio were 18. At this optimized setting the BTE was 27.1 % and the engine emitted 360...
-
Nucleate pool boiling on porous metallic coatings
PublicationPrzedstawiono wyniki systematycznych badań eksperymentalnych przejmowania ciepła podczas wrzenia pęcherzykowego wody destylowanej w stanie nasycenia od płaskich i cylindrycznych powierzchni o specjalnie przygotowanej powierzchni: gładkiej, chropowatej oraz pokrytej warstwą porowatą.
-
Liquid crystal technique application for heat transfer investigation inafin-tube heat exchanger element
PublicationPublikacja przedstawia rezultaty prac autorów w zakresie wykorzystania techniki ciekłokrystalicznej w badaniach wymiany ciepła dla elementów wymiennika ciepła. Technika ta z powodzeniem została zastosowana do analizy sposobu zabudowy wymiennika na jego efektywność.