Search
Search results for: pedot-rgo composite
-
Formation of Highly Conductive Boron-Doped Diamond on TiO2 Nanotubes Composite for Supercapacitor or Energy Storage Devices
PublicationIn the present paper, we report the phenomena of the formation of the novel composite nanostructures based on TiO2 nanotubes (NTs) over-grown by thin boron-doped diamond (BDD) film produced in Microwave Plasma Enhanced Chemical Vapor Deposition (PE MWCVD). The TiO2 nanotube array overgrown by boron-doped diamond immersed in 0.1 M NaNO3 can deliver high specific capacitance of 7.46 mF cm−2. The composite electrodes were characterized...
-
Towards Computer-Aided Graphene Covered TiO2-Cu/(CuxOy) Composite Design for the Purpose of Photoinduced Hydrogen Evolution
PublicationIn search a hydrogen source, we synthesized TiO2-Cu-graphene composite photocatalyst for hydrogen evolution. The catalyst is a new and unique material as it consists of copper-decorated TiO2 particles covered tightly in graphene and obtained in a fluidized bed reactor. Both, reduction of copper from Cu(CH3COO) at the surface of TiO2 particles and covering of TiO2-Cu in graphene thin layer by Chemical Vapour Deposition (CVD) were...
-
Impact response of novel layered two stage fibrous composite slabs with different support type
PublicationThe performance of novel Layered Two Stage Fibrous Composite slabs (LTSFC) was pioneered under falling mass collisions using a combined experimental and numerical study. Such LTSFC slabs consist of three layers with and without the insertion of glass fibre mesh between the layers. LTSFC techniques were used to fabricate the composite slabs with three layers including 3%, 1.5%, and 3% of fibre content for the top, middle, and...
-
A Quantitative Investigation of Dislocation Density in an Al Matrix Composite Produced by a Combination of Micro-/Macro-Rolling
PublicationAn aluminum matrix composite with dispersed carbon nanotubes (CNTs) was produced via flake powder metallurgy using a micro-rolling process and vacuum hot pressing (VHP), followed by conventional rolling using a macro-rolling process. The microstructure and mechanical properties of the produced composites were studied. In addition, a new quantitative model was introduced to study the dislocation density based on the microstructural...
-
Edgewise Compressive Behavior of Composite Structural Insulated Panels with Magnesium Oxide Board Facings
PublicationEdgewise compression response of a composite structural insulated panel (CSIP) with magnesium oxide board facings was investigated. The discussed CSIP is a novel multifunctional sandwich panel introduced to the housing industry as a part of the wall, floor, and roof assemblies. The study aims to propose a computational tool for reliable prediction of failure modes of CSIPs subjected to concentric and eccentric axial loads. An advanced...
-
Experimental and numerical investigation of mercury removal from flue gas by sorbent polymer composite
PublicationThis paper presents an experimental and numerical investigation of the performance of a sorbent polymer composite (SPC) material used for removing mercury from the flue gases in a full-scale industrial installation. The investigated material is an attractive alternative to activated carbon, which is commonly used for this purpose. While the application of the SPC is characterized by high capital expenditures, this technology offers...
-
Development, characterization and evaluation of composite adsorbent for the adsorption of crystal violet from aqueous solution: Isotherm, kinetics, and thermodynamic studies
PublicationThe purpose of this work focuses on the production and investigations of a new composite material as alternative low-cost adsorbent for the removal of crystal violet (CV) dye from waste solution. The production method was performed by in-situ thermal activation technology via extrusion process of polymer wastes containing tire rubber (50 wt%) and polyurethane foam (50 wt%) using single-screw extruder under processing temperature...
-
The Impact of Ground Tire Rubber Oxidation with H2O2 and KMnO4 on the Structure and Performance of Flexible Polyurethane/Ground Tire Rubber Composite Foams
PublicationThe use of waste tires is a very critical issue, considering their environmental and economic implications. One of the simplest and the least harmful methods is conversion of tires into ground tire rubber (GTR), which can be introduced into different polymer matrices as a filler. However, these applications often require proper modifications to provide compatibility with the polymer matrix. In this study, we examined the impact...
-
Wavelet Analysis for Damage Identification in Composite Structures
Publication -
Failure Analysis of footbridge made of composite materials
PublicationFinite element method analysis of a pedestrian footbridge made of sandwich material is presented. The internal structure of the material is modelled as a structural shell assuming the Equivalent Single Layer approach (ESL). Two FEM commercial codes are employed. The response of the structure is studied in order to determine the load level that activates Hashin and Tsai-Wu failure criteria. Some practical aspects of designing footbridges...
-
Tribological Behaviour of Copper-Graphene Composite Materials
Publication -
Wavelet analysis for damage identification in composite structures
Publicationw pracy zaproponowano metodę analizy sygnalu opartą o transformatę falkową, pozwalajacą na identyfikcaje pęknięcia zmęczeniowego w jednowymiarowych elementach konstrukcyjnych wykonanych z materialow kompozytowych
-
Wave Propagation Modelling in Composite Plates with Damages
PublicationW pracy przedstawiono model i wyniki analizy propagacji fali spręzystej w płycie kompozytowej z uszkodzeniami.
-
Detection of delamination in multi layer composite beams.
PublicationW pracy przedstawiono model belki kompozytowej z delaminacją. Omówiono czynniki propagacji fali sprężystej w belce i możliwości wykorzystania zmian w propagującej fali wywołanych delaminacją do jej detekcji.
-
Role of composite cathodes in single chamber SOFC.
PublicationZbadano wpływ składu katody na napięcie oraz wydajność ogniw paliwowych pracujących w konfiguracji jednokomorowej. W związku z tym, że takie ogniwo pracuje w mieszanienie powietrza i paliwa, napięcie jest określone przez różnice aktywności katalitycznej anody i katody. Typowy cermet na bazie niklu oraz związki perovskitów pracują dobrze odpowiednio jako anoda i katoda. Jednakże perowskity mają również właściwości katalityczne,...
-
Damage Detection of Steel-Concrete Composite Beam
Publication -
Fabrication methods of smart composite coatings - review
PublicationPostoperative bacterial infections are one of the main reasons for unsuccessful implantation of long-term implants. The development of bacterial infection requires antibiotic therapy, in extreme cases a reimplantation procedure is necessary. In order to provide materials for implants with antibacterial properties, they are subjected to modifications to create a coating that will release the drug substance, when the inflammation...
-
Thermal properties of a cement composite containing phase change materials (PCMs) with post-pyrolytic char obtained from spent tyres as a carrier
PublicationThis work examines the possible use of post-pyrolysis char made from spent vehicle tyres as a carrier for phase change materials (PCM), which could be used as an additive to cement mortar. Because of the ability of PCM to accumulate heat, the cement composite obtained from it, apart from its structural and strength properties, will acquire an additional energy storage function, which can be very important for energy-saving construction. In...
-
From Bioink to Tissue: Exploring Chitosan-Agarose Composite in the Context of Printability and Cellular Behaviour
PublicationThis study presents an innovative method for producing thermosensitive bioink from chitosan hydrogels saturated with carbon dioxide and agarose. It focuses on a detailed characterisation of their physicochemical properties and potential applications in biomedicine and tissue engineering. The ORO test approved the rapid regeneration of the three-dimensional structure of chitosan–agarose composites in a unidirectional bench press...
-
Experimental and numerical evaluation of mechanical behaviour of composite structural insulated wall panels under edgewise compression
PublicationA composite structural insulated sandwich panel (CSIP) is a quite novel approach to the idea of sandwich structures. A series of natural-scale experimental test is required each time a change in panel’s geometry is planned and a reliable computational tool is required to precede actual laboratory testing with virtual simulations. An attempt of creating such a tool has been made with use of a commercial FEM code ABAQUS, in order...
-
Experimental Studies of Concrete-Filled Composite Tubes under Axial Short- and Long-Term Loads
PublicationThe paper presents experimental studies on axially compressed columns made of concrete-filled glass fiber reinforced polymer (GFRP) tubes. The infill concrete was C30/37 according to Eurocode 2. The investigated composite pipes were characterized by different angles of fiber winding in relation to the longitudinal axis of the element: 20, 55 and 85 degrees. Columns of two lengths, 0.4 m and 2.0 m, were studied. The internal diameter...
-
Sintering Parameter Investigation for Bimetallic Stainless Steel 316L/Inconel 718 Composite Printed by Dual-Nozzle Fused Deposition Modeling
PublicationFused deposition modeling (FDM) nowadays offers promising future applications for fabricating not only thermoplastic-based polymers but also composite PLA/Metal alloy materials, this capability bridges the need for metallic components in complex manufacturing processes. The research is to explore the manufacturability of multi-metal parts by printing green bodies of PLA/multi-metal objects, carrying these objects to the debinding...
-
Ni/cerium Molybdenum Oxide Hydrate Microflakes Composite Coatings Electrodeposited from Choline Chloride: Ethylene Glycol Deep Eutectic Solvent
PublicationCerium molybdenum oxide hydrate microflakes are codeposited with nickel from a deep eutectic solvent-based bath. During seven days of exposure in 0.05 M NaCl solution, the corrosion resistance of composite coating (Ni/CeMoOxide) is slightly reduced, due to the existence of some microcracks caused by large microflakes. Multielemental analysis of the solution, in which coatings are exposed and the qualitative changes in the surface...
-
Deformation Analysis of a Composite Bridge during Proof Loading Using Point Cloud Processing
PublicationRemote sensing in structural diagnostics has recently been gaining attention. These techniques allow the creation of three-dimensional projections of the measured objects, and are relatively easy to use. One of the most popular branches of remote sensing is terrestrial laser scanning. Laser scanners are fast and efficient, gathering up to one million points per second. However, the weakness of terrestrial laser scanning is the...
-
Marta Kuc-Czarnecka dr
PeopleMarta Kuc-Czarnecka is the deputy head of the Department of Statistics and Economics at the Faculty of Management and Economics of the Gdańsk University of Technology. She also serves as the Dean's proxy for AMBA accreditation. She is a co-founder of Rethinking Economics Gdańsk and a member of the Foundation Edward Lipiński for the promotion of pluralism in economic sciences. In 2018-2022, she was Eurofound’s quality of life and...
-
Electrophoretically Deposited Chitosan/Eudragit E 100/AgNPs Composite Coatings on Titanium Substrate as a Silver Release System
PublicationDue to the possibility of bacterial infections occurring around peri-implant tissues, it is necessary to provide implant coatings that release antibacterial substances. The scientific goal of this paper was to produce by electrophoretic deposition (EPD) a smart, chitosan/Eudragit E 100/silver nanoparticles (chit/EE100/AgNPs) composite coating on the surface of titanium grade 2 using different deposition parameters, such as the...
-
Polyurethane/ground tire rubber composite foams based on polyglycerol: processing, mechanical and thermal properties
PublicationDuring the synthesis of rigid polyurethane foams, petrochemical polyol was substituted with polyglycerol, the product of thermo-catalytic polycondensation of waste glycerol, resulting from biodiesel production. Two types of ground tire rubbers, untreated and thermo-mechanically reclaimed, were used to obtain ‘‘green’’ polyurethane-polyglycerol composite foams. Samples were prepared by a single-step method for the ratio of NCO/OH...
-
Composite Hodgkin and non-Hodgkin lymphoma - Male, 65 - Tissue image [10100730045406631]
Open Research DataThis is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Composite Hodgkin and non-Hodgkin lymphoma - Male, 65 - Tissue image [10100730045404301]
Open Research DataThis is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Composite Hodgkin and non-Hodgkin lymphoma - Male, 65 - Tissue image [10100730045401001]
Open Research DataThis is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Composite Hodgkin and non-Hodgkin lymphoma - Male, 65 - Tissue image [10100730045409611]
Open Research DataThis is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Composite Hodgkin and non-Hodgkin lymphoma - Male, 65 - Tissue image [10100730045401421]
Open Research DataThis is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Composite Hodgkin and non-Hodgkin lymphoma - Male, 65 - Tissue image [10100730045407111]
Open Research DataThis is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Composite Hodgkin and non-Hodgkin lymphoma - Male, 65 - Tissue image [10100730045403771]
Open Research DataThis is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Composite Hodgkin and non-Hodgkin lymphoma - Male, 65 - Tissue image [10100730045403501]
Open Research DataThis is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
The topography of carbon black-polylactide composite 3D printed electrodes after femtosecond laser ablation
Open Research DataThis dataset contains a series of scanning electron microscopy images revealing the topography of 3D printed carbon black-polylactide composite electrodes after laser ablation with a femtosecond laser. Different laser powers were investigated, namely: 10%, 25%, 50%, 75% and 100%. The CB-PLA electrodes were 3D printed using an Ender printer. Femtosecond laser NKT Photonics, Origami XP parameters: power at 100%...
-
The Effect of AgInS2, SnS, CuS2, Bi2S3 Quantum Dots on the Surface Properties and Photocatalytic Activity of QDs-Sensitized TiO2 Composite
PublicationThe eect of type (AgInS2, SnS, CuS2, Bi2S3) and amount (5, 10, 15 wt%) of quantum dots (QDs) on the surface properties and photocatalytic activity of QDs-sensitized TiO2 composite, was investigated. AgInS2, SnS, CuS2, Bi2S3 QDs were obtained by hot-injection, sonochemical, microwave, and hot-injection method, respectively. To characterize of as-prepared samples high-resolution transmission electron microscopy (HRTEM), scanning...
-
Prediction of maximum tensile stress in plain-weave composite laminates with interacting holes via stacked machine learning algorithms: A comparative study
PublicationPlain weave composite is a long-lasting type of fabric composite that is stable enough when being handled. Open-hole composites have been widely used in industry, though they have weak structural performance and complex design processes. An extensive number of material/geometry parameters have been utilized for designing these composites, thereby an efficient computational tool is essential for that purpose. Different Machine Learning...
-
Epitoanyag-Journal of Silicate Based and Composite Materials
Journals -
Composite shells in 6-field nonlinear shell theory
PublicationW pracy przedstawiono równanie konstytutywne uwzględniające wielowarstwowość materiału powłoki. Równania wyprowadzono bazując na podejściu Equivalent Single Layer
-
Composite (La, Sr)MnO3-YSZ cathode for SOFC
PublicationW pracy przedstawiono właściwości elektryczne kompozytów (La,Sr)MnO3-YSZ. Materiały te dzieki swoim włąściwościom mogą staniwć dobry materiał na katody ogniw paliwowych. Przedstawiono też wyniki badań ogniwa paliwowego pracującego z paliwem wodorowym zbudowanego na bazie katody z kompozytu LSM-YSZ i anody Ni-YSZ. Uzyskano gęstośc mocy 0.26 W cm−2 przy temperaturze 850°C.
-
Modeling for Detection of Degraded Zones in Metallic and Composite Structures
PublicationW pracy przedstawiono przegląd metod modelowania uszkodzeń w postaci pęknięć i delaminacji wystepujących w elementach konstrukcyjnych
-
Experimental investigations of concrete dowels in composite floor system
PublicationOpisano nowy system stropow zespolonych umozliwiajacych montaz instalacji klimatyzacyjnych, wentylacyjnych i grzewczych w przestrzeni pomiedzy dwoma plytami betonowymi konstrukcji stropu: gorna i dolna. Obie plyty polaczone sa wzajemnie srodnikami stalowymi z wycieciami u gory i na dole w ksztalcie 'puzzle', ktore we wspolpracy z plyta betonowa tworza tzw. dyble betonowe. Wykonano badania laboratoryjne typu 'Push-out' tych polaczen...
-
Fracture in composite/aluminium joints of variable adhesive properties
PublicationA strain gauge technique recently developed with the wedge test, for estimating crack length and, thus, the fracture energy of structural adhesive bonding, has been employed on a system in which one adherend had two types of surface treatment. Simple polishing and polishing with subsequent sandblasting were the treatments used, with a distinct straight line, perpendicular to the sample edges, separating the two. Despite the clear-cut...
-
The influence of preparing conditions on the properties of SrTi0.98Nb0.02O3-YSZ composite
PublicationZbadano wpływ warunków przygotowania na właściwości kompozytów SrTi0.98Nb0.02O3-YSZ jako potencjalnych warstw przejściowych między anodą a elektrolitem w tlenkowych ogniwach paliwowych SOFC. Udowodniono, że proces wstępnej obróbki temperaturowej substratów oraz sposób ich mielenia znacznie wpływa na przewodnictwo elektryczne badanych materiałów.
-
Impedance Investigations of the Mechanism of Oxygen Evolution on Composite Electrodes
Publication -
Thermal and optical properties of P3HT:PC70BM:ZnO nanoparticles composite films
Publication -
Damage Detection in Composite Materials Using Hyperspectral Imaging
Publication -
Stability analysis of cylindrical composite shells in MSC/Nastran
PublicationW pracy badane jest zastosowanie systemu MSC/NASTRAN for Windows do analizy stateczności kompozytowych powłok cylindrycznych. Przeprowadzono obliczenia dla dwóch wybranych przykładów paneli cylindrycznych poddanych równomiernemu ściskaniu w kierunku tworzącej dokonując analizy zarówno w zakresie stateczności początkowej jak i problemu geometrycznie nieliniowego w procesie przyrostowym. Otrzymane wyniki w pełni potwierdziły bogate...
-
New ceramic and composite tools for smoothing burnishing process
PublicationW pracy przedstawiono nowe konstrukcje narzędzi ceramicznych i z kompozytu karbonado do nagniatania twardych hartowanych stali. Zamieszczono wyniki badań wpływu parametrów technologicznych nagniatania walcowych próbek ze stali 45 o różnej twardości 23-56HRC na chropowatość powierzchni próbek.